The effect of PtRuW ternary electrocatalysts on methanol oxidation reaction in direct methanol fuel cells

PtRu and PtRuW ternary electrocatalysts were synthesized using an NaBH₄ reduction method. A uniform distribution of particles, with average particle size of 3–3.5 nm was indentified from X-ray diffraction (XRD) and transmission electron microscopy (TEM). The electrochemically active surface area was slightly decreased after the addition of W into PtRu. When W was added to PtRu, the specific and mass activity of methanol electro-oxidation was increased. The most active catalyst was Pt₅Ru₄W, of which specific and mass activities were 265.38 mA/m² and 6.21 A/g^·catal, respectively. The specific and mass activity was 390 and 320% higher than that of PtRu.     

Nickel phthalocyanine-tetrasulfonic acid as a promoter of methanol electro-oxidation on Pt/C catalyst

This paper describes an investigation of the role of nickel phthalocyanine-tetrasulfonic acid (NiPcTs) for methanol electro-oxidation on a Pt/C catalyst. Cyclic voltammetry (CV) revealed that NiPcTs has no catalytic activity in methanol or CO electro-oxidation. However, methanol electro-oxidation occurs faster on a Pt/C catalyst modified with NiPcTs than on the original Pt/C catalyst. CO stripping results demonstrated that NiPcTs promotes electro-oxidation of adsorbed CO (CO_ads) on the Pt/C catalyst, which is likely to be responsible for the enhancement of the methanol electro-oxidation rate. The promotion effect of NiPcTs is attributable to its ability to modify the electron density of the Pt surface. The electron deficiency of Pt⁰ in the NiPcTs-Pt/C catalyst is shown by the shift of the Pt⁰ 4f peak to higher binding energies in the X-ray photoelectron spectrum.     

Investigations of Compositions and Performance of PtRuMo/C Ternary Catalysts for Methanol Electrooxidation

PtRuMo/C catalyst was prepared by impregnation reduction method and characterised. Comparison is made between a home‐made PtRu/C prepared by similar method and Pt/C (E‐Tek Co., Pt/C‐ET) catalysts. One glassy carbon disc electrode for ternary alloy catalyst was used to evaluate the catalytic performances by cyclic voltammetric, chronoamperometric, amperometric i–t curves, and electrochemical impedance spectra (EIS). The electrochemical measurement results indicated that the performance of PtRuMo/C with a molar ratio of 6:3:1 was the highest among 15 Pt_xRu_yMo_10–x–y/C catalysts with different molar ratios. The composition, particle size, lattice parameter and morphology of the PtRuMo(6:3:1)/C catalyst were determined by means of X‐ray energy dispersive analysis, X‐ray diffraction (XRD) and transmission electron micrographs (TEM). The result of XRD analysis exhibits that PtRuMo(6:3:1)/C has the fcc structure with the smaller lattice parameter than the home‐made PtRu/C and Pt/C‐ET. Its typical particle sizes is only about 5 nm. With respect to the catalytic activity and stability, the PtRuMo(6:3:1)/C catalyst is superior to PtRu/C despite their comparable active areas. Though the electrochemically active surface area of Pt/C‐ET is the biggest, its performance is the lowest. EIS results also indicate that the reaction resistances for methanol electrooxidation on the PtRuMo(6:3:1)/C catalyst are smaller than those of PtRu/C at different polarisation potentials.     

Effect of reduction conditions on electrocatalytic activity of a ternary PtNiCr/C catalyst for methanol electro-oxidation

The effect of reduction conditions on a Pt₂₈Ni₃₆Cr₃₆/C catalyst was investigated by using two different reduction methods: hydrogen reduction and NaBH₄ reduction. In hydrogen reduced catalysts, dissolution of metallic Ni and Cr was observed during cyclic voltammetry (CV) tests, and a larger amount of Ni and Cr was dissolved when reduced at higher temperatures. For methanol electro-oxidation, the highest specific current density of 1.70 A m⁻² at 600 s of the chronoamperometry tests was observed in the catalyst reduced at 300 °C, which was ∼24 times that of a Pt/C catalyst (0.0685 A m⁻²). In NaBH₄ reduced catalysts, formation of an amorphous phase and a more Pt-rich surface was observed in X-ray diffraction and CV results, respectively, with increasing amounts of NaBH₄. When reduced by 50 times of the stoichiometric amount of NaBH₄, the PtNiCr/C catalyst (PtNiCr-50t) showed a current density of 34.1 A g_{noble metal}⁻¹, which was 81% higher than the 18.8 A g_{noble metal}⁻¹ value of a PtRu/C catalyst at 600 s of the chronoamperometry tests. After 13 h of chronoamperometry testing, the activity of the PtNiCr-50t (15.0 A g_{noble metal}⁻¹) was 110% higher than the PtRu/C catalyst (7.15 A g_{noble metal}⁻¹). The PtNiCr/C catalyst shows promise as a Ru-free methanol oxidation catalyst.     

Single-step polyol synthesis of alloy Pt<Subscript>7</Subscript>Sn<Subscript>3</Subscript> versus bi-phase Pt/SnO<Subscript>x</Subscript> nano-catalysts of controlled size for ethanol electro-oxidation

Disordered alloy and bi-phase PtSn nanoparticles of nominal Pt:Sn ratio of 70:30 atomic % with controlled size and narrow size distribution were synthesized using a single-step polyol method. By adjusting the solution pH it was possible to obtain Pt₇Sn₃ nanoparticles of various sizes from 2.8 to 6.5 nm. We found that the presence of NaOH in the synthesis solution not only influenced the nanoparticle size, but as it was revealed by XRD, it apparently also dictated the degree of Pt and Sn alloying. Three catalysts prepared at lower NaOH concentrations (C_NaOH < 0.15 M) showed disordered alloy structure of the nominal composition, while the other three catalysts synthesized at higher NaOH concentrations (C_NaOH > 0.15 M) consisted of bi-phase nanoparticles comprising a crystalline phase close to that of pure Pt together with an amorphous Sn phase. These observations are plausibly due to the phase separation and formation of monometallic Pt and amorphous SnO_x phases. A proposed reaction mechanism of Pt₇Sn₃ nanoparticle formation is presented to explain these observations along with the catalytic activities measured for the six synthesized carbon-supported Pt₇Sn₃ catalysts. The highest catalytic activity towards ethanol electro-oxidation was found for the carbon-supported bi-phase catalyst that formed the largest Pt (6.5 nm) nanoparticles and SnO_x phase. The second best catalyst was a disordered alloy Pt₇Sn₃ catalyst with the second largest nanoparticle size (5 nm), while catalysts of smaller size (4.5–4.6 nm) but different structure (disordered alloy vs. bi-phase) showed similar catalytic performance inferior to that of the 5 nm disordered alloy Pt₇Sn₃ catalyst. This work demonstrated the importance of producing bi-metallic PtSn catalysts with large Pt surfaces in order to efficiently electro-oxidize ethanol.     

Reduction of CO<Subscript>2</Subscript> to CO via reverse water-gas shift reaction over CeO<Subscript>2</Subscript> catalyst

CeO₂ catalysts with different structure were prepared by hard-template (Ce-HT), complex (Ce-CA), and precipitation methods (Ce-PC), and their performance in CO₂ reverse water gas shift (RWGS) reaction was investigated. The catalysts were characterized using XRD, TEM, BET, H₂-TPR, and in-situ XPS. The results indicated that the structure of CeO₂ catalysts was significantly affected by the preparation method. The porous structure and large specific surface area enhanced the catalytic activity of the studied CeO₂ catalysts. Oxygen vacancies as active sites were formed in the CeO₂ catalysts by H₂ reduction at 400 °C. The Ce-HT, Ce-CA, and Ce-PC catalysts have a 100% CO selectivity and CO₂ conversion at 580 °C was 15.9%, 9.3%, and 12.7%, respectively. The highest CO₂ RWGS reaction catalytic activity for the Ce-HT catalyst was related to the porous structure, large specific surface area (144.9 m²?g^?1) and formed abundant oxygen vacancies.     

Comparative study of the preparation and electrochemical performance of LiNi<Subscript>1</Subscript><Subscript>/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript> electrode material for rechargeable lithium batteries

Positive electrode material LiNi_1/2Mn_1/2O₂ was synthesized via the carbonate co-precipitation method and the hydroxide precipitation route to study the effects of the precursor on its structural and electrochemical properties. The results of X-ray diffraction and Rietveld refinement show that the carbonate precursor of Ni²⁺ and Mn²⁺ exhibits one phase at a pH of 8.5, while the hydroxide deposit separates into Ni(OH)₂ and Mn(OH)₂ phases under the same experimental conditions. LiNi_1/2Mn_1/2O₂ material prepared from the hydroxide precursor shows 8.9% Li/Ni exchange and a large capacity loss of 11.3% in the first 10 cycles. By contrast, more uniform distribution of transition metal ions and stable Mn²⁺ in the carbonate precursor contribute to only 7.8% Li/Ni disorder in the obtained LiNi_1/2Mn_1/2O₂, which delivers a reversible capacity of about 182 mAh g⁻¹ at a current rate of 14 mA g⁻¹ between 2.5 and 4.8 V.     

Effects of surface area on electrochemical performance of Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript> cathode material

The effect of surface area on the electrochemical properties and thermal stability of Li[Ni_0.2Li_0.2Mn_0.6]O₂ powders was characterized using a charge/discharge cycler and DSC (Differential Scanning Calorimeter). The surface area of the samples was successfully controlled from ~4.0 to ~11.7 m² g⁻¹ by changing the molar ratio of the nitrate/acetate sources and adding an organic solvent such as acetic acid or glucose. The discharge capacity and rate capability was almost linearly increased with increase in surface area of the sample powder. A sample with a large surface area of 9.6–11.7 m² g⁻¹ delivered a high discharge capacity of ~250 mAh g⁻¹ at a 0.2 C rate and maintained 62–63% of its capacity at a 6 C rate versus a 0.2 C rate. According to the DSC analysis, heat generation by thermal reaction between the charged electrode and electrolyte was not critically dependent on the surface area. Instead, it was closely related to the type of organic solvent employed in the fabrication process of the powder.     

Synthesis and catalytic properties of nanostructured Me/Mn<Subscript>0.5</Subscript>Ce<Subscript>0.5</Subscript>O<Subscript>2</Subscript> in the oxidation of carbon monoxide

The nanostructured solid solution Mn_0.5Ce_0.5O₂ is synthesized to develop effective noble metal free catalysts for the detoxification of technogenic contaminants. Its chemical and phase compositions and textural characteristics are studied by differential thermal analysis, X-ray diffraction analysis, laser mass spectrometry, and low-temperature nitrogen adsorption. The activity of the solid solution in the oxidation of carbon monoxide is determined by the flow method within a temperature range of 20–300°C at atmospheric pressure, a gas hourly space velocity of 1800 h⁻¹ for the following gas mixture composition, vol %: CO, 3.6; O₂, 8.0; N₂, balance. The activity of Mn_0.5Ce_0.5O₂ is shown to be appreciably higher than the activity of MnO_x and CeO₂, and the temperature of 100% conversion is 92, 120, and 210°C, respectively. Using the solid solution as a support and the technique of impregnation, we synthesize the nanostructured catalysts Cu/Mn_0.5Ce_0.5O₂ and Ag/Mn_0.5Ce_0.5O₂, which manifest high activity in the oxidation of carbon monoxide: the temperature of 100% conversion is 77 and 85°C, respectively. The new catalysts could be of interest for the purification of industrial and motor vehicle wastes.     

Effect of reaction conditions on the catalytic performance of Co<Subscript>9</Subscript>Fe<Subscript>3</Subscript>Bi<Subscript>1</Subscript>Mo<Subscript>12</Subscript>O<Subscript>51</Subscript> in the oxidative dehydrogenation of n-butene to 1,3-butadiene

Oxidative dehydrogenation of n-butene to 1,3-butadiene over Co₉Fe₃Bi₁Mo₁₂O₅₁ catalyst was conducted in a continuous flow fixed-bed reactor. The effect of reaction conditions (steam/n-butene ratio, reaction temperature, and space velocity) on the catalytic performance of Co₉Fe₃Bi₁Mo₁₂O₅₁ was investigated. Steam played an important role in decreasing contact time, suppressing total oxidation of n-butene, and removing coke during the reaction. Yield for 1,3-butadiene showed a volcano-shaped curve with respect to steam/n-butene ratio. The compensation between thermodynamic effect and kinetic effect led to a volcano-shaped curve of 1,3-butadiene yield with respect to reaction temperature. The Co₉Fe₃Bi₁Mo₁₂O₅₁ catalyst showed the best catalytic performance at a certain value of space velocity. The optimum steam/n-butene ratio, reaction temperature, and gas hourly space velocity were found to be 15, 420 °C, and 675 h⁻¹, respectively.     

Pt45Ru45M10/C (M = Fe, Co, and Ni) catalysts for methanol electro-oxidation

Pt₄₅Ru₄₅M₁₀/C (M = Fe, Co, and Ni) catalysts were synthesized and physical and electrochemical properties were analyzed by XRD, TEM, CO stripping and methanol electro-oxidation activity measurement. Among these catalysts, the Pt₄₅Ru₄₅Fe₁₀/C catalyst exhibited the highest mass activity of 2.6 A/g catal. while those of the Pt₄₅Ru₄₅Co₁₀/C and Pt₄₅Ru₄₅Ni₁₀/C catalysts were 2.2 and 2.5 A/g catal., respectively. In the case of specific activity, the catalysts exhibited much higher activities of 110 (130%), 120 (140%) and 150 (170%) mA/m² for the Fe, Co and Ni incorporated catalysts, respectively, than 88 mA/m² of a commercial PtRu/C catalyst.     

Synthesis and electrochemical properties of layered LiNi<Subscript>1/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript>prepared by coprecipitation

Spherical LiNi_1/2Mn_1/2O ₂ powders were synthesized from LiOH . H₂O and coprecipitated metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The average particle size of the powders was about 10 m and the size distribution was quite narrow due to the homogeneity of the metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The tap-density of the LiNi_1/2Mn_1/2O₂ powders was approximately 2.2 g cm_–3, which is comparable to the tap-density of commercial LiCoO₂. The LiNi_1/2Mn_1/2 O₂electrode delivered a discharge capacity of 152, 163, 183, and 189 mA h g^–1 in the voltage ranges of 2.8–4.3, 2.8–4.4, 2.8–4.5, and 2.8–4.6 V, respectively, with good cyclability. Furthermore, Al(OH)₃-coated LiNi_1/2Mn_1/2O₂exhibited excellent cycling behavior and rate capability compared to the pristine electrode.     

Preparation and electrochemical performance of Li-rich layered cathode material,Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript>, for lithium-ion batteries

The Li-rich layered cathode material, Li[Ni_0.2Li_0.2Mn_0.6]O₂, was synthesized via a “mixed oxalate” method, and its structural and electrochemical properties were compared with the same material synthesized by the sol–gel method. X-ray diffraction (XRD) shows that the synthesized powders have a layered O₃–LiCoO₂-type structure with the R-3m symmetry. X-ray photoelectron spectroscopy (XPS) indicates that in the above material, Ni and Mn exist in the oxidation states of +2 and +4, respectively. The layered material exhibits an excellent electrochemical performance. Its discharge capacity increases gradually from the initial value of 228 mA hg⁻¹ to a stable capacity of over 260 mA hg⁻¹ after the 10th cycle. It delivers a larger capacity of 258 mA hg⁻¹ at the 30th cycle. The dQ/dV curves suggest that the increasing capacity results from the redox-reaction of Mn⁴⁺/Mn³⁺.     

Copolymerization of Vinyl Chloride and Ethylene with Cp<Superscript>*</Superscript>Ti( OCH<Subscript>3</Subscript>)<Subscript>3</Subscript>/MAO Catalyst

Summary Copolymerization of vinyl chloride (VC) and ethylene with Cp^*Ti( OCH₃)₃/MAO catalyst was investigated. The Cp^*Ti( OCH₃)₃/MAO catalyst initiated the copolymerization of VC with ethylene, although the copolymer yields were low. In the ¹³C NMR spectra of the copolymers, the peaks based on junction part between VC and ethylene was observed, but the signals were small. From DSC measurement of the copolymers, only one glass transition temperature was observed. Thus, it is clear that the copolymerization with Cp^*Ti( OCH₃)₃/MAO catalysts gave the copolymer, and the copolymer consisting of block sequence rather than random copolymer. Received: 13 November 2002/Revised: 6 January 2003/Accepted: 10 January 2003 Correspondence to Kiyoshi Endo     

Solution-Combustion Synthesis of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> as a Cathode Material for Lithium-Ion Batteries

A cathode material for lithium-ion batteries–LiNi_1/3Co_1/3Mn_1/3O₂–was prepared by solution combustion synthesis and characterized by XRD, SEM, and galvanostatic charge/discharge cycling. The sample calcined at 950°C for 10 h showed best charge/discharge performance. An initial discharge capacity (C) of 150.5 mA h g^–1 retained 95.7% of its value after 75 charge/discharge cycles at I_c = 14 mA g^–1 (0.2C rate), I_d = 70 mA g^–1 (0.5C rate).     

Influence of phosphorous addition on Bi<Subscript>3</Subscript>Mo<Subscript>2</Subscript>Fe<Subscript>1</Subscript> oxide catalysts for the oxidative dehydrogenation of 1-butene

Bi₃Mo₂Fe₁P _x oxide catalysts were prepared by a co-precipitation method and the influence of phosphorous content on the catalytic performance in the oxidative dehydrogenation of 1-butene was investigated. The addition of phosphorous up to 0.4mole ratio to Bi₃Mo₂Fe₁ oxide catalyst led to an increase in the catalytic performance; however, a higher phosphorous content (above P=0.4) led to a decrease of conversion. Of the tested catalysts, Bi₃Mo₂Fe₁P_0.4 oxide catalyst exhibited the highest catalytic performance. Characterization results showed that the catalytic performance was related to the quantity of a π-allylic intermediate, facile desorption behavior of adsorbed intermediates and ability for re-oxidation of catalysts.     

Pd/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts on cellular supports for VOC vapor neutralization

The results from investigating the influence of temperature, concentration, and flow rate on the catalytic oxidation of vapors of volatile organic compounds (VOCs) in the presence of Pd/γ-Al₂O₃ catalyst on cellular supports are presented. The activity of Pd/γ-Al₂O₃ catalysts on ceramic and metal monolith supports with a cellular structure during the catalytic neutralization of VOC (ethanol, ethyl acetate) vapors under laboratory conditions was determined, and the most stable catalyst for the preliminary study of a large batch was chosen. A pilot unit was created to test a large batch of cellular monolith catalyst in neutralizing VOC vapors under conditions of flexographic production. It was established that a high rate of conversion (> 99 %) was achieved for VOC concentrations of 0.5 g/m³ at space velocities of up to ∼10⁴ h⁻¹, and for VOC concentrations of 5.0 g/m³ at space velocities of up to ∼5 × 10⁵ h⁻¹. The change in the activity of the catalysts on metal (nickel alloyed by aluminum) and ceramic cellular supports in service was investigated. After 300–500 min of operation, virtually complete deactivation of catalyst on a metal support was observed, accompanied by the formation of nickel oxide and acetate. Pilot unit tests with catalyst on cellular supports having a volume of 14.5 l in neutralizing the ventilation exhausts of flexographic production confirmed the possibility of more than 90% conversion at VOC concentrations of ∼0.1 g/m³ and more than 97% at VOC concentrations of over 1 g/m³. A consistently high conversion of VOC was observed during a 100 h test of the pilot unit. A system for recovering the heat released during VOC oxidation lowers the operating costs of the pilot unit.     

Insoluble Wilkinson Catalyst RhCl(TPPTS)<Subscript>3</Subscript> Supported on SBA-15 for Heterogeneous Hydrogenation with and Without Supercritical CO<Subscript>2</Subscript>

The insoluble Wilkinson catalyst RhCl[P(m-C₆H₄SO₃)Na)₃]₃ changes from inert to very active by supported on mesoporous material SBA-15, and the catalyst is stable, easy to separate from products, clean, and can be reused directly. This catalyst combines the advantages of homogeneous catalysts and heterogeneous catalysts very well.     

Characterization and electrocatalytic properties of PtRu/C catalysts prepared by impregnation-reduction method using Nd2O3 as dispersing reagent

A simple impregnation-reduction method introducing Nd₂O₃ as dispersing reagent has been used to synthesize PtRu/C catalysts with uniform Pt-Ru spherical nanoparticles. X-ray diffraction (XRD) analysis, transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) analysis have been used to characterize the composition, particle size and crystallinity of the catalysts. Well-dispersed catalysts with average particle size about 2 nm are achieved. The electrochemically active surface area of the different PtRu/C catalysts is determined by the CO_ad-stripping voltammetry experiment. The electrocatalytic activities of these catalysts towards methanol electrooxidation are investigated by cyclic voltammetry measurements and ac impedance spectroscopy. The in-house prepared PtRu/C catalyst (PtRu/C-03) in 0.5 M H₂SO₄ + 1.0 M CH₃OH at 30 °C display a higher catalytic activity and lower charge-transfer resistance (R_t) than that of the standard PtRu/C catalyst (PtRu/C-C). It is mainly due to enhanced electrochemically active specific surface, higher alloying extent of Ru and the abundant Pt⁰ and Ru oxides on the surface of the PtRu/C catalyst.     

Study of electrochemical properties and the charge/discharge mechanism for Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>/MnO<Subscript>2</Subscript>-AC hybrid supercapacitor

Spinel Li₄Mn₅O₁₂ was prepared by a sol–gel method. The manganese oxide and activated carbon composite (MnO₂-AC) were prepared by a method in which KMnO₄ was reduced by activated carbon (AC). The products were characterized by XRD and FTIR. The hybrid supercapacitor was fabricated with Li₄Mn₅O₁₂ and MnO₂-AC, which were used as materials of the two electrodes. The pseudocapacitance performance of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor was studied in various aqueous electrolytes. Electrochemical properties of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor were studied by using cyclic voltammetry, electrochemical impedance measurement, and galvanostatic charge/discharge tests. The results show that the hybrid supercapacitor has electrochemical capacitance performance. The charge/discharge test showed that the specific capacitance of 51.3 F g⁻¹ was obtained within potential range of 0–1.3 V at a charge/discharge current density of 100 mA g⁻¹ in 1 mol L⁻¹ Li₂SO₄ solution. The charge/discharge mechanism of Li₄Mn₅O₁₂ and MnO₂-AC was discussed.