Electrochemical oxidation of oxalic acid at highly boron-doped diamond electrodes

Electrochemical oxidation of oxalic acid has been investigated at bare, highly boron-doped diamond electrodes. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. Hydrogen-terminated diamonds exhibited well-defined peaks of oxalic acid oxidation in a wide pH range. A good linear response was observed for a concentration range from 50 nM to 10 microM, with an estimated detection limit of approximately 0.5 nM (S/N = 3). In contrast, oxygen-terminated diamonds showed no response for oxalic acid oxidation inside the potential window, indicating that surface termination contributed highly to the control of the oxidation reaction. An investigation with glassy carbon electrodes was conducted to confirm the surface termination effect on oxalic acid oxidation. Although a hydrogen-terminated glassy carbon electrode showed an enhancement of signal-to-background ratio in comparison with untreated glassy carbon, less stability of the current responses was observed than that at hydrogen-terminated diamond.     

Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

The electrochemistry of histamine and serotonin in neutral aqueous media (pH 7.2) was investigated using polycrystalline, boron-doped diamond thin-film electrodes. Cyclic voltammetry, hydrodynamic voltammetry, and flow injection analysis (FIA) with amperometric detection were used to study the oxidation reactions. Comparison experiments were carried out using polished glassy carbon (GC) electrodes. At diamond electrodes, highly reproducible and well-defined cyclic voltammograms were obtained for histamine with a peak potential at 1.40 V vs SCE. The voltammetric signal-to-background ratios obtained at diamond were 1 order of magnitude higher than those obtained for GC electrodes at and above 100 microM analyte concentrations. A linear dynamic range of 3-4 orders of magnitude and a detection limit of 1 microM were observed in the voltammetric measurements. Well-defined sweep rate-dependent voltammograms were also obtained for 5-hydroxytryptamine (5-HT). The characteristics of the voltammogram indicated lack of adsorption of its oxidation products on the surface. No fouling or deactivation of the electrode was observed within the experimental time of several hours. A detection limit of 0.5 microM (signal-to-noise ratio 13.8) for histamine was obtained by use of the FIA technique with a diamond electrode. A remarkably low detection limit (10 nM) was obtained for 5-HT on diamond by the same method. Diamond electrodes exhibited a linear dynamic range from 10 nM to 100 microM for 5-HT determination and a range of 0.5-100 microM for histamine determination. The FIA response was very reproducible from film to film, and the response variability was below 7% at the actual detection limits.     

Direct electrochemical oxidation of disulfides at anodically pretreated boron-doped diamond electrodes

Anodically oxidized diamond electrodes have been used to oxidize disulfides, thiols, and methionine in aqueous acidic media and tested for amperometric detection of these compounds after chromatographic separation. Cyclic voltammetric signals for 1 mM glutathione disulfide (GSSG) were observed at 1.39 and 1.84 V vs SCE, the values being less positive than those of its as-deposited counterpart as well as glassy carbon electrode. The voltammetric and chronocoulometric results have indicated the high stability of the electrode with negligible adsorption. A positive shift in the peak potential with increasing pH indicated the attractive electrostatic interaction between the anodically oxidized diamond surface and the positively charged GSSG in acidic media that promoted its analytical performance. The results of the electrolysis experiments of disulfides and thiols showed that the oxidation reaction mechanism of glutathione (GSH) and GSSG involves oxygen transfer. Following separation by liquid chromatography (LC), the determination of both GSH and GSSG in rat whole blood was achieved at a constant potential (1.50 V vs Ag/AgCl), and the limits of detection for GSH and GSSG were found to be 1.4 nM (0.028 pmol) and 1.9 nM (0.037 pmol) with a linear calibration range up to 0.25 mM. These detection limits were much lower than those reported for the amperometry using Bi-PbO2 electrodes and LC-mass spectrometry, and the LC method using diamond electrodes were comparable with enzymatic assay in real sample analysis. The high response stability and reproducibility together with the possibility of regeneration of the electrode surface by on-line anodic treatment at 3 V for 30 min further support the applicability of anodically pretreated diamond for amperometric detection of disulfides.     

Electrochemical degradation of chlorobenzene on boron-doped diamond and platinum electrodes

In this paper the electrochemical degradation of chlorobenzene (CB) was investigated on boron-doped diamond (BDD) and platinum (Pt) anodes, and the degradation kinetics on these two electrodes was compared. Compared with the total mineralization with a total organic carbon (TOC) removal of 85.2% in 6 h on Pt electrode, the TOC removal reached 94.3% on BDD electrode under the same operate condition. Accordingly, the mineralization current efficiency (MCE) during the mineralization on BDD electrode was higher than that on the Pt electrode. Besides TOC, the conversion of CB, the productions and decay of intermediates were also monitored. Kinetic study indicated that the decay of CB on BDD and Pt electrodes were both pseudo-first-order reactions, and the reaction rate constant (k_s) on BDD electrode was higher than that on Pt electrode. The different reaction mechanisms on the two electrodes were investigated by the variation of intermediates concentrations. Two different reaction pathways for the degradation of CB on BDD electrode and Pt electrode involving all these intermediates were proposed.     

Anodic oxidation of wastewater containing the Reactive Orange 16 Dye using heavily boron-doped diamond electrodes

Boron-doped diamond (BDD) films grown on the titanium substrate were used to study the electrochemical degradation of Reactive Orange (RO) 16 Dye. The films were produced by hot filament chemical vapor deposition (HFCVD) technique using two different boron concentrations. The growth parameters were controlled to obtain heavily doped diamond films. They were named as E1 and E2 electrodes, with acceptor concentrations of 4.0 and 8.0 × 10²¹ atoms cm⁻³, respectively. The boron levels were evaluated from Mott-Schottky plots also corroborated by Raman's spectra, which characterized the film quality as well as its physical property. Scanning Electron Microscopy showed well-defined microcrystalline grain morphologies with crystal orientation mixtures of (1 1 1) and (1 0 0). The electrode efficiencies were studied from the advanced oxidation process (AOP) to degrade electrochemically the Reactive Orange 16 azo-dye (RO16). The results were analyzed by UV/VIS spectroscopy, total organic carbon (TOC) and high-performance liquid chromatography (HPLC) techniques. From UV/VIS spectra the highest doped electrode (E2) showed the best efficiency for both, the aromaticity reduction and the azo group fracture. These tendencies were confirmed by the TOC and chromatographic measurements. Besides, the results showed a direct relationship among the BDD morphology, physical property, and its performance during the degradation process.     

Examination of the spatially heterogeneous electroactivity of boron-doped diamond microarray electrodes

Spatial variations in the electrical and electrochemical activity of microarray electrodes, fabricated entirely from diamond, have been investigated. The arrays contain approximately 50-mum-diameter boron-doped diamond (BDD) disks spaced 250 mum apart (center to center) in insulating intrinsic diamond supports, such that the BDD regions are coplanar with the intrinsic diamond. Atomic force microscopy (AFM) imaging of the surface reveals a roughness of no more than +/-10 nm over the array. Each BDD microdisk within the array contains polycrystalline BDD with a variety of different grains exposed. Using conducting-AFM, the conductivity of the different grains was found to vary within a BDD microdisk. Electrochemical imaging of the electroactivity of the microdisk electrodes using scanning electrochemical microscopy operating in substrate generation-tip collection mode revealed that, under apparently diffusion-limited steady-state conditions, there was a small variation in the response between electrodes. However, the majority of electrodes in the array appeared to show predominantly metallic behavior. For the electrodes that showed a lower activity, all grains within the microdisk supported electron transfer, albeit at different rates, as evidenced by studies on the electrodeposition of metallic silver, at potentials far negative of the flat band potential of oxygen-terminated polycrystalline diamond. The possibility of using these array electrodes for steady-state diffusion-limited measurements in electroanalytical applications is far-reaching. However, caution should be exercised in the kinetic analysis of voltammetric measurements, since wide variations in the electroactivity of individual grains are apparent when the potential is below the diffusion-limited value.     

掺硼金刚石膜电极在液晶盒残留液晶清洗中的应用研究

目前液晶盒残留液晶的清洗一般采用非ODS有机溶剂的溶解或表面活性剂的乳化分散作用来去除，效果并不十分理想。应用掺硼金刚石膜电极这一现今热点研究的功能材料，提出了将金刚石膜电极电化学高级氧化技术的氧化分解作用与水基清洗剂的传质、渗透、分散作用相结合的清洗技术，并通过实验确定了K3PO4添加浓度为0．4mol，L和清洗温度为70℃的最佳关键清洗参数，能在充分发挥高级氧化作用的同时，保证水基清洗剂最佳的传质、渗透和分散作用，有效实现了液晶盒残留液晶的高效清洗。     

Label-free sequence-specific DNA sensing using copper-enhanced anodic stripping of purine bases at boron-doped diamond electrodes

Stripping voltammetric determination of purine bases in the presence of copper ions at mercury, amalgam, or carbon-based electrodes has recently been utilized in analysis of DNA or synthetic oligodeoxynucleotides (ODNs). Here we report on copper-enhanced label-free anodic stripping detection of guanine and adenine bases in acid-hydrolyzed DNA at anodically oxidized boron-doped diamond electrode (AO-BDDE). The AO-BDDE was successfully applied in a three-electrode microcell in which an approximately 50 microL drop of the analyte solution can be efficiently stirred during the accumulation step by streaming of an inert gas. Accelerated mass transport due to the solution motion in the presence of copper resulted in enhancement of the guanine oxidation signal by about 2 orders of magnitude (compared to accumulation of the analyte from still solution not containing copper), allowing an easy detection of approximately 25 fmol of the ODNs. The proposed technique is shown to be suitable for a determination of purine (particularly guanine) content in DNA samples. Applications of the technique in magnetic bead-based DNA assays (such as hybridization with DNA sequences exhibiting asymmetrical distribution of purine/pyrimidine nucleotides between the complementary strands or monitoring of amplification of specific DNA fragments in a duplex polymerase chain reaction) are demonstrated.     

Thiol-yne reaction on boron-doped diamond electrodes: application for the electrochemical detection of DNA-DNA hybridization events

Boron-doped diamond (BDD) interfaces were chemically functionalized through the catalyst free thiol-yne reaction. Different thiolated precursors (e.g., perfluorodecanethiol, 6-(ferrocenyl)-hexanethiol, DNA) were successfully "clicked" to alkynyl-terminated BDD by irradiating the interface at 365 nm for 30 min. Thiolated oligonucleotide strands were immobilized using the optimized reaction conditions, and the surface concentration was tuned to obtain a surface coverage of 3.1 × 10(12) molecules cm(-2). Electrochemical impedance spectroscopy (EIS) was employed to follow the kinetics of hybridization and dehybridization events. The sensitivity of the oligonucleotide modified BDD interface was assayed, and a detection limit of 1 nM was obtained.     

Experimental and theoretical investigations on the compressibility of nanocrystalline nickel

We investigated nanocrystalline nickel experimentally (x-ray diffraction) and theoretically (cluster ab initio calculations). No phase transition was observed in nano-nickel. The volume, isothermal bulk modulus and its pressure derivative derived experimentally and theoretically are 43.56 (0.13) ų, 228(15) GPa, 4.02(0.51) and 44.00 ų, 217 GPa and 3.20, respectively. We found no appreciable change in the value of bulk modulus for nano-nickel as compared to the bulk-nickel.An erratum to this article can be found at     

Selective voltammetric and amperometric detection of uric acid with oxidized diamond film electrodes

Electrochemically anodized diamond film electrodes were used for selective detection of uric acid (UA) in the presence of high concentrations of ascorbic acid (AA) by differential pulse voltammetry and chronoamperometry. Because the oxidation peak potential for AA is approximately 450 mV more positive than that for UA at anodized diamond electrodes, UA can be determined with very good selectivity. By use of chronoamperometry, linear calibration curves were obtained for UA over the concentration range up to 1 x 10(-6) M in 0.1 M HClO4 solution, with the lowest experimental value measured being 5 x 10(-8) M. This is consistent with the fact that a statistical analysis of the calibration curve yielded a detection limit of 1.5 x 10(-8) M (S/N = 3). AA in less than 20-fold excess does not interfere. The practical analytical utility of the method is demonstrated by the measurement of UA in human urine and serum without any preliminary treatment.     

Large-amplitude Fourier transformed high-harmonic alternating current cyclic voltammetry: kinetic discrimination of interfering Faradaic processes at glassy carbon and at boron-doped diamond electrodes

Significant advantages of Fourier transformed large-amplitude ac higher (second to eighth) harmonics relative to responses obtained with conventional small-amplitude ac or dc cyclic voltammetric methods have been demonstrated with respect to (i) the suppression of capacitive background currents, (ii) the separation of the reversible reduction of [Ru(NH(3))(6)](3+) from the overlapping irreversible oxygen reduction process under conditions where aerobic oxygen remains present in the electrochemical cell, and (iii) the kinetic resolution of the reversible [Ru(NH(3))(6)](3+/2+) process in mixtures of [Fe(CN)(6)](3-) and [Ru(NH(3))(6)](3+) at appropriately treated boron-doped diamond electrodes, even when highly unfavorable [Fe(CN)(6)](3-) to [Ru(NH(3))(6)](3+) concentration ratios are employed. Theoretical support for the basis of kinetic discrimination in large-amplitude higher harmonic ac cyclic voltammetry is provided.     

Electrochemical oxidation of chlorophenols at a boron-doped diamond electrode and their determination by high-performance liquid chromatography with amperometric detection

Anodically pretreated diamond electrodes have been used for the detection of chlorophenols (CPs) in environmental water samples after high-performance liquid chromatographic (HPLC) separation. The anodization of as-deposited boron-doped polycrystalline diamond thin-film electrodes has enabled the stable determination of phenols over a wide concentration range. Prior to the HPLC analysis, a comparative study with ordinary glassy carbon, as-deposited diamond, and anodized diamond was made to examine the oxidative behavior of phenols by cyclic voltammety and flow injection analysis with amperometric detection. At anodized diamond electrodes, reproducible, well-defined cyclic voltammograms were obtained even at high CP concentration (5 mM), due to a low proclivity for adsorption of the oxidation products on the surface. In addition, after prolonged use, the partially deactivated diamond could be reactivated on line by applying a highly anodic potential (2.64 Vvs SCE) for 4 min, which enabled the destruction of the electrodeposited polymer deposits. Hydroxyl radicals produced by the high applied potential, in which oxygen evolution occurs, are believed to be responsible for the oxidation of the passivating layer on the surface. When coupled with flow injection analysis (FIA), anodized diamond exhibited excellent stability, with a response variability of 2.3% (n = 100), for the oxidation of a high concentration (5 mM) of chlorophenol. In contrast, glassy carbon exhibited a response variability of 39.1%. After 100 injections, the relative peak intensity, for diamond decreased by 10%, while a drastic decrease of 70% was observed for glassy carbon. The detection limit obtained in the FIA mode for 2,4-dichlorophenol was found to be 20 nM (S/N = 3), with a linear dynamic range up to 100 microM. By coupling with the column-switching technique, which enabled on-line preconcentration (50 times), the detection limit was lowered to 0.4 nM (S/N = 3). By use of this technique, anodized diamond electrodes were demonstrated for the analysis of CPs in drainwater that was condensed from the flue gas of waste incinerators.     

Kinetic studies of hydroquinone_quinone at the boron-doped diamond electrode by cyclic voltammetry

Abstracts are not published in this journal This revised version was published online in November 2006 with corrections to the Cover Date.     

Direct electrochemistry of Shewanella loihica PV-4 on gold nanoparticles-modified boron-doped diamond electrodes fabricated by layer-by-layer technique

Microbial Fuel Cells (MFCs) are robust devices capable of taping biological energy, converting pollutants into electricity through renewable biomass. The fabrication of nanostructured electrodes with good bio- and electrochemical activity, play a profound role in promoting power generation of MFCs. Au nanoparticles (AuNPs)-modified Boron-Doped Diamond (BDD) electrodes are fabricated by layer-by-layer (LBL) self-assembly technique and used for the direct electrochemistry of Shewanella loihica PV-4 in an electrochemical cell. Experimental results show that the peak current densities generated on the Au/PAH multilayer-modified BDD electrodes increased from 1.25 to 2.93 microA/cm(-2) as the layer increased from 0 to 6. Different cell morphologies of S. loihica PV-4 were also observed on the electrodes and the highest density of cells was attached on the (Au/PAH)6/BDD electrode with well-formed three-dimensional nanostructure. The electrochemistry of S. loihica PV-4 was enhanced on the (Au/PAH)4/BDD electrode due to the appropriate amount of AuNPsand thickness of PAH layer.     

Differential pulse voltammetry of toxic metal ions at the boron-doped CVD diamond electrode

Boron-doped polycrystalline diamond films were grown over a molybdenum substrate by a microwave plasma CVD process using a methane and hydrogen gas mixture at a pressure of 35 ± 1 Torr. Boron doping of diamond was achieved in situ by using a solid boron source while growing diamond in the CVD processxu. We have observed a negligible background current (l) for diamond by differential pulse voltammetry in 0.5 M NaCl, 0.5 M H₂SO₄, and 0.5 M HNO₃ solutions over a wide potential range. Therefore, diamond will certainly have a use as an electrode material in electroanalytical applications to detect trace toxic/nontoxic metal ions such as cadmium, lead, copper, and silver. Differential pulse voltammetry was used to detect and evaluate the presence of lead ions in 0.5 M NaCl and cadmium ions in 0.5 M H₂SO₄ supporting electrolyte solution using highly conducting boron-doped diamond coated molybdenum electrode material. Furthermore, reverse differential pulse voltammetry was used to evaluate the presence of copper and silver ions in 0.5 M H₂SO₄ and 0.5 M HNO₃ solution, respectively. Diamond electrode has been used in this study to detect metallic ions in the solution over a wide potential range that covers + 0.8 V to –0.4 V vs., SHE.     

Laser activation voltammetry: selective removal of reduced forms of methyl viologen deposited on glassy carbon and boron-doped diamond electrodes

The effect of high-intensity laser pulses on the reduction of methyl viologen at glassy carbon electrodes in aqueous solution is investigated using laser activation voltammetry (LAV) under both channel flow and no-flow conditions and compared with the effect of conventional variable-temperature voltammetry. The reduction proceeds in two consecutive one-electron steps, and the neutral two-electron-reduction product of methyl viologen is shown by voltammetry and in situ optical microscopy to form two types of deposits, amorphous and crystalline, on the electrode surface. Laser activation voltammetry using a 10 Hz pulsed Nd-YAG 532 nm laser is shown to remove the deposits from the electrode surface at different laser intensities: the amorphous material is more easily ablated than the crystalline deposit. By conventional variable-temperature voltammetry, it is shown that the two stripping peaks disappear as the temperature is increased. However, with conventional heating, the opposite ease of removal is detected compared to the case of laser activation voltammetry: the stripping response associated with the crystalline material disappears at lower temperatures compared to that for the amorphous material. In the presence of high-intensity laser pulses (>0.17 W cm(-2)), glassy carbon surfaces are damaged and the voltammetric characteristics become poor. It is shown that, by the employment of a thin-film boron-doped diamond electrode grown using a chemical vapor deposition procedure on a tungsten substrate, much higher laser intensities can be applied and well-defined LAV signals can be obtained without deactivation of the electrode.     

不同氩气与氢气流量比对硼掺杂纳米金刚石膜的影响

采用直流热阴极PCVD方法,以B(OCH3)3作为硼源,通过改变氩气与氢气流量比,在p型Si衬底上沉积了硼掺杂纳米金刚石膜.研究了不同氩气与氢气流最比对掺硼金刚石膜生长的影响.采用扫描电子显微镜、拉曼光谱仪、X射线衍射仪、霍尔系统等对样品的形貌、结构和导电性能进行了表征.结果表明,随着氩气与氢气流量比的增加,膜的晶粒尺寸由微米级向纳米级转变,并且膜中非晶碳成分增多,膜的导电性能变好.     

Experimental and theoretical investigations of Mg2+-doped single-crystal fibres of lithium niobate

Pure and Mg-doped single-crystal LiNbO₃ fibres (molar concentrations up to 5 mol.% MgO) have been investigated via X-ray diffraction and micro-Raman scattering experiments in order to compare their structural (cell volume) and dynamical (modes) properties with those of bulk material. Novel first-principles calculations have been performed to ascertain definitely the frequency assignments of TO and LO zone-centre phonons involved in Raman spectra. Three main differences between fibres and bulk are (i) the fibre is not spatially homogeneous at low doping rates (macroscopic homogeneity is achieved when the doping rate reaches 5 mol.%); (ii) the doping dependence of Raman frequencies and linewidths is not the same for certain modes; (iii) the cell volume in the fibres decreases with increasing doping rate in the fibre in contrast with previously reported data on the bulk. Experimental results indicate the presence of two successive regimes when the Mg doping rate is increased up to 5%. This behaviour, already noticed though apparently to a lesser extent in the bulk, is discussed in the framework of a consistent double-vacancy model that encompasses previously proposed models as particular cases. This confirms that Mg²⁺ ions replace antisite Nb ions in a first stage (below 2% in the fibre) while, in a second stage (from 2% to 5% doping rates), Mg²⁺ ions are accommodated in remaining Li vacancies until these are completely filled. The reordering that ensues is undoubtedly linked with the recovered homogeneity of the fibre, the disappearance of photo-refractive effects and the considerable improvement of the resistance to optical damage observed for the 5 mol.% Mg doped crystal.