DMFCs用SPEEK/SiOx-S复合质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalized silica powder with sulfonic acid groups (SiOx-S) was added into the SPEEK matrix (DS 55.1%) to prepare SPEEK/ SiOx-S composite membranes. The decrease in both the swelling degree and the methanol permeability of the membranes was a dose-dependent result of addition of the SiOx-S powder. Pure SPEEK membrane swelled 52.6% at 80°C, whereas the SPEEK/SiOx-S (15%, by mass) membrane swelled only 27.3% at the same temperature. From room temperature to 80℃, all SPEEK/SPEEK/SiOx-S composite membranes had methanol permeability of about one order of magnitude lower than that of Nafion115. Compared with pure SPEEK membranes, the addition of the SiOx-S powder not only leads to higher proton conductivity, but also increases the dimensional stability at higher temperatures, and greater proton conductivity can be achieved at higher temperature. The SPEEK/SiOx-S (20%, by mass) membrane could withstand temperature up to 145°C, at which in 100% relative humidity (RH) its proton conductivity exceeded slightly that of Nafion115 membrane and reached 0.17 S•cm－1, while pure SPEEK mem-brane dissolved at 90°C. The SPEEK/SiOx-S composite membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

直接甲醇燃料电池用三羧基丁烷膦酸锆/磺化杂萘联苯聚醚酮复合质子交换膜

用高磺化度的磺化杂萘联苯聚醚酮（SPPEK）制备DMFC质子交换膜时,膜的机械强度会因过度溶胀而下降。通过在SPPEK（DS=61%）中掺杂1,2,4-三羧基丁烷-2-膦酸锆(Zr(PBTC)),我们制备出 Zr(PBTC)/SPPEK复合质子交换膜。实验表明, Zr(PBTC)的掺杂能有效降低膜的吸水量（溶胀）,并能减小膜的甲醇透过系数。80℃时,30wt.%Zr(PBTC) /SPPEK复合膜的吸水量与SPPEK膜比降低了30％。室温下复合膜的甲醇透过系数在10－7 cm2.s-1数量级上,比Nafion 115膜低一个数量级以上。液体甲醇溶液进料的DMFC单电池测试表明,30wt.%Zr(PBTC) /SPPEK复合膜的电池性能优于SPPEK的电池性能。     

Sulfonated poly(ether sulfone)/silica composite membranes for direct methanol fuel cells

A series of sulfonated poly(ether sulfone) (SPES)/silica composite membranes were prepared by sol–gel method using tetraethylorthosilicate (TEOS) hydrolysis. Physico–chemical properties of the composite membranes were characterized by thermogravimetric analysis (TGA), X‐ray diffraction (XRD), scanning electron microscope–energy dispersive X‐ray (SEM–EDX), and water uptake. Compared to a pure SPES membrane, SiO₂ doping in the membranes led to a higher thermal stability and water uptake. SEM–EDX indicated that SiO₂ particles were uniformly embedded throughout the SPES matrix. Proper silica loadings (below 5 wt %) in the composite membranes helped to inhibit methanol permeation. The permeability coefficient of the composite membrane with 5 wt % SiO₂ was 1.06 × 10^?7 cm²/s, which was lower than that of the SPES and just one tenth of that of Nafion® 112. Although proton conductivity of the composite membranes decreased with increasing silica content, the selectivity (the ratio of proton conductivity and methanol permeability) of the composite membrane with 5 wt % silica loading was higher than that of the SPES and Nafion® 112 membrane. This excellent selectivity of SPES/SiO₂ composite membranes could indicate a potential feasibility as a promising electrolyte for direct methanol fuel cell. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Sulfonated poly(ether sulfone)/phosphotungstic acid/attapulgite composite membranes for direct methanol fuel cells

Novel composite sulfonated poly(ether sulfone)(SPES)/phosphotungstic acid (PWA)/attapulgite (AT) membranes were investigated for direct methanol fuel cells (DMFCs). Physical–chemical properties of the composite membranes were characterized by FTIR, DSC, TGA, SEM‐EDX, water uptake, tensile test, proton conductivity, and methanol permeability. Compared with a pure SPES membrane, PWA, and AT doping in the membrane led to a higher thermal stability and glass transition temperature (T_g) as revealed by TGA and DSC. Tensile test indicated that lower AT content (3%) in the composite can significantly increase the tensile strength, while higher AT loading demonstrated a smaller contribution on strength. Proper PWA and AT loadings in the composite membranes can increase the proton conductivity and lower the methanol cross‐over. The proton conductivity of the SPES‐P‐A 10% composite membrane reached 60% of the Nafion 112 membrane conductivity at room temperature while the methanol permeability was only one‐fourth of that of Nafion 112 membrane. This excellent performances of SPES/PWA/AT composite membranes could indicate a potential feasibility as a promising electrolyte for DMFC. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

DMFCs用磺化聚醚醚酮/磺化酚酞型聚醚砜共混质子交换膜

A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein poly(ether sulfone) (SPES-C, DS 53.7%) is blended with the SPEEK matrix (DS 55.1%, 61.7%) to prepare SPEEK/SPES-C blend membrane. The decrease in swelling degree and methanol permeability of the membrane is dose-dependent. Pure SPEEK (DS 61.7%) membrane dissolves completely in water at 70ºC, whereas the swelling degree of the SPEEK (DS 61.7%)/SPES-C (40%, by mass) membrane is 29.7% at 80ºC. From room temperature to 80ºC, the methanol permeability of all SPEEK (DS 55.1%)/SPES-C blend membranes is about one order of magnitude lower than that of Nafion®115. At higher temperature, the addition of SPES-C polymer increases the dimensional stability and greater proton conductivity can be achieved. The SPEEK (DS 55.1%)/SPES-C (40%, by mass) membrane can withstand temperatures up to 150ºC. The proton conductivity of SPEEK (DS 55.1%)/SPES-C (30%, by mass) membrane approaches 0.16 S•cm－1, matching that of Nafion115 at 140ºC and 100% RH, while pure SPEEK (DS 55.1%) membrane dissolves at 90ºC. The SPEEK/SPES-C blend membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.     

聚醚砜/磺化聚醚醚酮共混膜的制备和性能

采用流延法制备了聚醚砜(PES)含量不同的PES/磺化聚醚醚酮(SPEEK)共混膜。PES与SPEEK具有良好的相容性。所制备PES/SPEEK共混膜的含水率、溶胀度和甲醇透过系数均随PES含量的增加而降低。虽然共混膜的质子传导性能有所降低.但阻醇性能和溶胀性能提高,这说明PES/SPEEK共混膜是一种很好的直接甲醇燃料电池用固体高分子电解质膜材料。     

Sulfonated poly(ether ether ketone)/zirconium tricarboxybutylphosphonate composite proton-exchange membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is a very promising alternative membrane material for direct methanol fuel cells. However, with a fairly high degree of sulfonation (DS), SPEEK membranes can swell excessively and even dissolve at high temperature. This restricts membranes from working above a high tolerable temperature to get high proton conductivity. To deal with this contradictory situation, insolvable zirconium tricarboxybutylphosphonate (Zr(PBTC)) powder was employed to make a composite with SPEEK polymer in an attempt to improve temperature tolerance of the membranes. SPEEK/Zr(PBTC) composite membranes were obtained by casting a homogeneous mixture of Zr(PBTC) and SPEEK in N,N-dimethylacetamide on a glass plate and then evaporating the solvent at 60°C. Many characteristics were investigated, including thermal stability, liquid uptake, methanol permeability and proton conductivity. Results showed significant improvement not only in temperature tolerance, but also in methanol resistance of the SPEEK/Zr(PBTC) composite membranes. The membranes containing 30 wt-% ∼ 40 wt-% of Zr(PBTC) had their methanol permeability around 10^-7 cm²·s^-1 at room temperature to 80°C, which was one order of magnitude lower than that of Nafion ^¯115. High proton conductivity of the composite membranes, however, could also be achieved from higher temperature applied. At 100% relative humidity, above 90°C the conductivity of the composite membrane containing 40 wt-% of Zr(PBTC) exceeded that of the Nafion ^¯115 membrane and even reached a high value of 0.36 S·cm^-1 at 160°C. Improved applicable temperature and high conductivity of the composite membrane indicated its promising application in DMFC operations at high temperature.     

PWA/silica doped sulfonated poly(ether sulfone) composite membranes for direct methanol fuel cells

A novel sulfonated poly(ether sulfone) (SPES)/phosphotungstic acid (PWA)/silica composite membranes for direct methanol fuel cells (DMFCs) application were prepared. The structure and performance of the obtained membranes were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), water uptake, proton conductivity, and methanol permeability. Compared to a pure SPES membrane, PWA and SiO₂ doped membranes had a higher thermal stability and glass transition temperature (T_g) as revealed by TGA‐FTIR and DSC. The morphology of the composite membranes indicated that SiO₂ and PWA were uniformly distributed throughout the SPES matrix. Proper PWA and silica loadings in the composite membranes showed high proton conductivity and sufficient methanol permeability. The selectivity (the ratio of proton conductivity to methanol permeability) of the SPES‐P‐S 15% composite membrane was almost five times than that of Nafion 112 membrane. This excellent selectivity of SPES/PWA/silica composite membranes indicate a potential feasibility as a promising electrolyte for DMFC. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Sulfonated (graphene oxide/poly(ether ketone ether sulfone) (S-GO/S-PEKES) composite proton exchange membrane with high proton conductivity for direct methanol fuel cell

ABSTRACT

Sulfonated poly(ether ketone ether sulfone) (S-PEKES) was successfully prepared to obtain the currently highest degree of sulfonation of 0.744. Sulfonated graphene oxide (S-GO) was incorporated into the S-PEKES matrix to increase sulfonic groups (SO₃H) which significantly improved the proton conductivity, methanol blocking, and mechanical stability. The proton conductivity of the S-GO/S-PEKES composite membrane was enhanced up to 5.93 × 10^?2 S.cm^?1, which was 7 times higher than the commercial Nafion 117. S-GO exhibited additional positive effects namely the blocking of methanol passing through the membrane, leading to lower methanol crossover than Nafion 117 by two orders of magnitude and high mechanical stability.     

Mass transport of direct methanol fuel cell species in sulfonated poly(ether ether ketone) membranes

Homogeneous membranes based on sulfonated poly(ether ether ketone) (sPEEK) with different sulfonation degrees (SD) were prepared and characterized. In order to perform a critical analysis of the SD effect on the polymer barrier and mass transport properties towards direct methanol fuel cell species, proton conductivity, water/methanol pervaporation and nitrogen/oxygen/carbon dioxide pressure rise method experiments are proposed. This procedure allows the evaluation of the individual permeability coefficients in hydrated sPEEK membranes with different sulfonation degrees. Nafion^® 112 was used as reference material. DMFC tests were also performed at 50 °C. It was observed that the proton conductivity and the permeability towards water, methanol, oxygen and carbon dioxide increase with the sPEEK sulfonation degree. In contrast, the SD seems to not affect the nitrogen permeability coefficient. In terms of selectivity, it was observed that the carbon dioxide/oxygen selectivity increases with the sPEEK SD. In contrast, the nitrogen/oxygen selectivity decreases. In terms of barrier properties for preventing the DMFC reactants loss, the polymer electrolyte membrane based on the sulfonated poly(ether ether ketone) with SD lower or equal to 71%, although having slightly lower proton conductivity, presented much better characteristics for fuel cell applications compared with the well known Nafion^® 112. In terms of the DMFC tests of the studied membranes at low temperature, the sPEEK membrane with SD = 71% showed to have similar performance, or even better, as that of Nafion^® 112. However, the highest DMFC overall efficiency was achieved using sPEEK membrane with SD = 52%.     

A modified poly(aryle ether ketone sulfone) proton exchange membrane with in situ polymerized polypyrrole for the direct methanol fuel cells

Bone tissue interfacial scaffolds, which encourage cell growth, are critical determinants for clinical success after implant surgery. Over the years, a number of resorbable configurations have emerged for bone cell support and growth, but only a few have demonstrated clinical efficacy. Polymer coatings produced by electrospinning are regarded as very promising bone interfaces because of the ultrathin‐scaled dimensions of its physical structure. In this study, the morphology, composition, thermal properties, and cell growth viability of a number of polylactide‐based systems containing different binary and ternary formulations of this biomaterial with collagen and commercial hydroxyapatite nanoparticles were characterized. The best performance in terms of biocompatibility was obtained for the tricomponent system in which the submicron fibers were further subjected to uniaxial orientation process during formation. The in vitro proliferation of the cells, which harbored on these ultrathin‐structured mats, was examined by means of a metabolic activity indicator and ensured by means of scanning electron microscopy, and cell anchorage was checked by fluorescent optical microscopy. Finally, the optimum tricomponent material was successfully sterilized for the first time by gamma radiation without noticeable losses in cell‐seeding capacity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Sulfonated poly(ether imide) and poly(ether sulfone) blends for direct methanol fuel cells. I. Sulfonation of PEI and characterization of the products

This investigation examines characteristics of sulfonated polyether imides (SPEI) with various ion exchange capacity values (IEC) and completes previous work to enable its blends to be adopted as polyelectrolyte in direct methanol fuel cells (DMFC). Polyether imides (PEI) were sulfonated by using chlorosulfonic acid as the sulfonating agent and chloroform as the solvent. The structure of SPEI was observed by FTIR and ¹H NMR. The sulfonate or sulfonic acid content of the polymers, expressed as a number per repeat unit of the polymer, was accurately determined by elemental analysis and conductometric titration. Physical properties such as solubility, intrinsic viscosities, thermal stability, and glass transition temperature (T_g) were studied for both PEI and SPEI. TGA‐FTIR verified that sulfonic groups, attached to the aromatic ring in the PEI backbone, are split at 230–350°C, but the main‐chain splitting temperature of SPEI is similar to that of pure polymer. The sulfonated samples exhibited good solubilities and increased glass transition temperatures (T_g values) as degree of sulfonation (DS) increased; two T_g values were detected when IEC was sufficiently high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

磷钨酸/二氧化硅/磺化聚醚醚酮复合膜的制备、表征与性能

以二氧化硅和磷钨酸改性磺化聚醚醚酮制得一种新型磺化聚醚醚酮复合膜。复合膜中杂多酸仍然保持着Keggin型PW12O430-阴离子的特征结构,二氧化硅和磷钨酸以无定形状态均匀分散于复合膜中。磷钨酸/二氧化硅/磺化聚醚醚酮复合膜的阻醇性能优于Nafion115;质子导电性能随着温度的提高有所增加。复合膜在磷钨酸中具有良好的稳定性。     

Influence of casting conditions on the properties of sulfonated poly(ether ether ketone ketone)/phosphotungstic acid composite proton exchange membranes

The sulfonated poly(ether ether ketone ketone)/phosphotungstic acid (SPEEKK/PWA) composite membranes were researched for proton exchange membranes. The effect of casting condition on the properties of membranes was studied in detail. The study showed that the casting condition has great influence on the membrane properties because of the hydrogen bond between the SPEEK and PWA and the interaction between the SPEEKK and dimethylformamide (DMF). The PWA particles are well crystallized on the surface when the velocity of the solvent volatilization is very slow under the SEM. The study will favor further research on excellent composite membranes for proton exchange membrane fuel cells. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 4020–4026, 2007     

Sulfonated polyether ether ketone composite proton exchange membranes incorporated with a novel hierarchical-structure hybrid nanofiller consisting solid superacid zirconium phosphate and CNTs

How to simultaneously improved the proton conductivity and mechanical strength is a key problem facing currently used proton exchange membranes (PEMs). Herein, a solid inorganic superacid-zirconium phosphate (ZrP) with a two-dimensional layer structure was combined with one-dimensional carbon nanotubes (CNTs) to prepare hybrid nanofiller ZrP-CNTs by an in situ chemical deposition method. The new hybrid nanofiller was then applied to modify sulfonated polyether ether ketone (SPEEK), a widely used PEM matrix, to obtain a series of composite membranes. The structure and properties of the membranes were fully characterized by SEM, XRD, FTIR, TG, tensile properties, and proton conductivity. The results showed that the proton conductivities of the membranes were significantly improved due to the addition of super solid acid-ZrP that has abundant proton sources or proton sites. Moreover, the composite membranes exhibited better mechanical properties and thermal stability than those of pure SPEEK membrane, owing to the great interface interaction and good compatibility between ZrP-CNTs and SPEEK. The composite membrane (2 wt% ZrP-CNTs) demonstrated the optimal comprehensive performance. Its proton conductivity was 36.63 mS cm⁻¹ and its tensile strength was 37.56 MPa, which was 70% and 10%, respectively, higher than those of the pure SPEEK membrane under the same condition.     

Improved performance of carbon‐based supercapacitors with sulfonated poly(ether ether ketone)/poly(vinyl alcohol) composite membranes as separators

Supercapacitors have attracted much interest because of their high power density and long cycling life. However, the porous polypropylene membranes that are widely used as separators in supercapacitors are unfavorable for transporting ions and constructing the interfaces between electrolyte and electrodes due to their hydrophobic property. As a consequence, a crosslinked solid polymer electrolyte membrane and a semi‐interpenetrating polymer network (sIPN) were fabricated from sulfonated poly(ether ether ketone) (SPEEK) and poly(vinyl alcohol) (PVA), which can be used as hydrophilic separators. Their structures were examined using Fourier transform infrared spectroscopy. The electrochemical properties of assembled electrical double‐layer capacitors (EDLCs) were investigated using cyclic voltammetry, galvanostatic charging–discharging and impedance analysis. At a current density of 1 A g^?1, a single electrode in the EDLC with the sIPN shows a specific capacitance of 134 F g^?1. As a comparison, a single electrode in the EDLC with a SPEEK membrane demonstrates a specific capacitance of only 121 F g^?1. After 1000 charge–discharge cycles, the specific capacitance retentions of both EDLCs are nearly 100%. These results suggest that the sIPN based on SPEEK and PVA has great potential to serve as a separator in EDLCs. © 2018 Society of Chemical Industry     

Preparation and characterization of poly(vinylidene fluoride)/sulfonated poly(phthalazinone ether sulfone ketone) blends for proton exchange membrane

Poly(vinylidene fluoride)/sulfonated poly(phthalazinone ether sulfone ketone) (PVdF/SPPESK) blend membranes are successfully prepared by solution blending method for novel proton exchange membrane (PEM). PVdF crystallinity, FTIR‐ATR spectroscopy, thermal stability, morphology, water uptake, dimension stability, and proton conductivity are investigated on PVdF/SPPESK blends with different PVdF contents. XRD and DSC analysis reveal that the PVdF crystallinity in the blends depends on PVdF content. The FTIR‐ATR spectra indicate that SPPESK remains proton‐conducting function in the blends due to the intactness of ? SO₃H group. Thermal analysis results show a very high thermal stability (T_d1 = 246–261°C) of the blends. PVdF crystallinity and morphology study demonstrate that with lower PVdF content, PVdF are very compatible with SPPESK. Also, with lower PVdF content, PVdF/SPPESK blends possess high water uptake, e.g., P/S 10/90 and P/S 15/85 have water uptake of 135 and 99% at 95°C, respectively. The blend membranes also have good dimension stability because the swelling ratios are at a fairly low level (e.g., 8–22%, 80°C). PVdF/SPPESK blends with low PVdF content exhibit very high proton conductivity, e.g., at 80°C, P/S 15/85 and P/S 10/90 reach 2.6 × 10^?2 and 3.6 × 10^?2 S cm^?1, respectively, which are close to or even higher than that (3.4 × 10^?2 S cm^?1) of Nafion115 under the same test condition. All above properties indicate that the PVdF/SPPESK blend membranes (particularly, with 10–20% of PVdF content) are very promising for use in PEM field. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Sulfonated poly(ether ether sulfone) copolymers for proton exchange membrane fuel cells

Novel aromatic sulfonated poly(ether ether sulfone)s (SPEESs) with tert‐butyl groups were synthesized by aromatic nucleophilic polycondensation of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone (SDCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS), and tert‐butylhydroquinone (TBHQ). The resulting copolymers showed very good thermal stability and could be cast into tough membranes. The morphology of the membranes was investigated with atomic force microscopy. The proton conductivity of SPEES‐40 membranes increased from 0.062 S/cm at 25°C to 0.083 S/cm at 80°C, which was higher than the 0.077 S/cm of Nafion 117 under the same testing conditions. These copolymers are good candidates to be new polymeric electrolyte materials for proton exchange membrane fuel cells. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1443–1450, 2007     

磺化聚醚醚酮／氧化石墨复合膜的制备与表征

采用液相氧化法制备了氧化石墨（GO）,以浓硫酸为磺化剂与聚醚醚酮反应制备了磺化聚醚醚酮（SPEEK）。采用溶液共混法制备了不同组成的SPEEK／GO复合膜,并运用FTIR、XRD、DSC、TG对复合膜进行了表征。研究表明,当氧化石墨和磺化聚醚醚酮复合后,氧化石墨的层间距由0．8nm增大至1．1nm,这说明磺化聚醚醚酮极性基团或者高分子链段已经插入到氧化石墨片层之间。DSC结果显示,氧化石墨的加入,在一定程度上降低了SPEEK的结晶性能。TG分析表明,在温度低于300℃,复合膜的热稳定性比磺化聚醚醚酮的略有降低,但当温度高于450℃后,复合膜的热稳定性反而得到提高。     

Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009