Effects of carbon fiber length on the tribological properties of paper-based friction materials

Four kinds of paper-based friction materials reinforced with carbon fibers of 100, 400, 600 and 800 μm were prepared by paper-making processes. Experimental results showed that the friction materials became porous with fiber length increasing. The friction torque curves were flat except the sample with 100 μm fibers. The wear rate of the sample with 100 μm fibers was only 1.40×10⁻⁵ mm³/J. Tiny debris and fine scratches formed in the worn surface were the reason for excellent wear resistance of friction pairs with 100 μm fibers. The friction pairs with 400, 600 and 800 μm fibers showed typically abrasive wear and fatigue wear.     

Synthesis of boride coatings on steel using plasma transferred arc (PTA) process and its wear performance

Boriding of the surface of a tool steel using boron powder and the plasma transferred arc process was investigated. It was shown that this method is an easy and effective technique in producing uniform alloyed layers with a thickness of about 1.5 mm and a hardness between 1000 and 1300 HV.The microstructure of the borided surfaces consists of primary Fe₂B-type borides and a eutectic mixture of borides and martensite. Some cracks are observed in the eutectic regions but they do not seem to critically affect the behaviour of the coatings in sliding wear.The wear rate of pin on disc tests is primarily affected by the applied load and it lies between 10⁻⁵ mm³/m for low loads and 10⁻² mm³/m for high loads. Two distinct regimes of mild and severe wear are obtained separated by a critical load. Mild wear is due to the load supporting effect of borides and severe wear is due to their breakage above a critical load. The wear rate is not significantly affected by the sliding velocity and is consistent with the friction coefficient.The friction coefficient varies from 0.13 to 0.23 and depends strongly on the oxidation status of the wear track. The sliding velocity affects the sliding distance where the coefficient of friction reaches equilibrium.     

Synergy between tribo-oxidation and strain rate response on governing the dry sliding wear behavior of titanium

The present work provides an insight into the dry sliding wear behavior of titanium based on synergy between tribo-oxidation and strain rate response. Pin-on-disc tribometer was used to characterize the friction and wear behavior of titanium pin in sliding contact with polycrystalline alumina disk under ambient and vacuum condition. The sliding speed was varied from 0.01 to 1.4 ms^?1, normal load was varied from 15.3 to 76 N and with a sliding distance of 1500 m. It was seen that dry sliding wear behavior of titanium was governed by combination of tribo-oxidation and strain rate response in near surface region of titanium. Strain rate response of titanium was recorded by conducting uni-axial compression tests at constant true strain rate of 100 s^?1 in the temperature range from 298 to 873 K. Coefficient of friction and wear rate were reduced with increased sliding speed from 0.01 to 1.0 ms^?1. This is attributed to the formation of in situ self lubricating oxide film (TiO) and reduction in the intensity of adiabatic shear band cracking in the near surface region. This trend was confirmed by performing series of dry sliding tests under vacuum condition of 2 × 10^?4 Torr. Characterization tools such as optical microscopy, scanning electron microscopy, and X-ray diffractometer provided evidence of such processes. These experimental findings can be applied to enhance the dry sliding wear behavior of titanium with proper choice of operating conditions such as sliding speed, normal load, and environment.     

Analysis of load-speed sensitivity of friction composites based on various synthetic graphites

The frictional response of a multi-component phenolic-based friction material is highly complex under a set of variable loads and speeds. The present paper discusses the sensitivity of friction coefficient (μ) of friction composites containing synthetic graphite with different particle sizes (with similar crystallinity range) to braking pressure and sliding speed. The friction studies were carried out on a sub scale brake-test-rig, following 4 loads × 3 speeds experimental design. The best combination of performance properties was observed for the composite containing synthetic graphite with an average particle size of 410 μm. Other particle sizes which resulted in good performance were 38 and 169 μm. Very fine particle sizes were not beneficial for desired combination of performance properties. Regression analysis of μ following an orthogonal L₉(3 × 3) experimental design method revealed that the first order influences of sliding speed and braking pressure were significant. When all the combinatorial influences of braking pressure and sliding speed are taken into account together their simultaneous effects would be most effective in the range of graphite particle size ～80–250 μm.     

Wear characteristics of a diffusion bonded sintered steel with short term surface treatments

A pin on disc machine was used to investigate the tribological behavior of a diffusion bonded sintered steel, with and without surface treatments of steam oxidation and manganese phosphating, over a wide range of speed (0.2–4 m/s) and applied load (4–500 N) in conditions of dry sliding and starved lubrication by oil impregnation of the porous structure of the materials. Besides the calculated wear rates, the wear mechanisms were determined by examination of the components of the rubbing system (sintered pin, disc and generated debris). A transition from a mild to a severe wear regime was identified, denoted by sharp changes of the wear rate. A transient wear regime, interposed between the mild and severe wear regimes, was detected. The rubbing surface quality degradation was in terms of material displacement around the pin circumference due to a delamination wear mechanism. Such regime was detected for the base sintered steel in dry sliding at 1 m/s for the load range 60–80 N and for both surface treatments in oil impregnated sliding at 0.5 m/s for the load range 200–300 N. Oil impregnation of the base sintered steel expanded the mild wear regime towards higher loads throughout the whole sliding speed range compared to dry sliding. For the lower speeds of 0.2 and 0.5 m/s, manganese phosphated samples in dry sliding exhibited higher transition loads compared to the base sintered steel. The lower oil impregnability of the surface treated samples, due to the sealing of porosity by steam oxidation, led to slightly lower transition loads in oil impregnated sliding, compared to the base sintered steel.     

Wear behavior of electroless Ni–P–B4C composite coatings

In this research, the wear of electroless Ni–P and Ni–P–B₄C composite coatings was reviewed. Auto catalytic reduction of Ni in nickel sulfate and sodium hypophosphate bath including suspended B₄C particles with different concentration was used to create composite coatings with 12, 18, 25 and 33 vol.% of B₄C particles. Coatings 35 μm thick were heat treated at 400 °C for one hour in an argon atmosphere and the wear resistance and friction coefficient of heat-treated samples were determined by block-on-ring tests. All wear tests were carried out at 24 °C, 35% moisture, 0.164 m/s sliding speed and about 1000 m sliding distance. Graphs show that an electroless Ni–P–B₄C composite coating with 25 vol.% of B₄C had the best wear resistance against a CK45 steel counterface.     

Effect of soft carbon black on tribology of deproteinised and polyisoprene rubbers

In this work, the tribological properties of deproteinised natural rubber (DPNR) were examined and compared with synthetic cis-1,4-polyisoprene rubber (IR), namely Natsyn 2200. The effect of adding carbon black (CB) (0, 25 and 50 phr) to both DPNR and IR on the friction and wear characteristics was investigated. Dry abrasion tests were carried out using pin-on-cylinder tribometer with abrasive paper (Diamond 50) under different operating test conditions such as applied normal load (5–35 N), sliding speed (0.3–1.5 m/s) and sliding distance (90–450 m).Experimental results showed that the addition of CB has significantly affected the wear and friction characteristics of both DPNR and IR, i.e. it reduces the abrasion weight loss by more than 70% compared to unfilled rubber, depending on the test conditions and the concentration of CB. The friction coefficient of DPNR was decreased by about 12.5% upon the addition of 50 phr CB, compared to unfilled DPNR. Meanwhile, adding (25–50 phr) CB to IR drastically deteriorates the friction coefficient, i.e. an increase in the friction by about 200% at 25 phr CB and 300% at 50 phr CB compared to unfilled IR.Finally, scanning electron microscopy (SEM) technique is employed to observe the abrasion pattern of rubber in order to correlate the experimental test results to the wear mechanisms.     

Impact of die wear and punch surface textures on aluminium can wall

Aluminium can manufacturing uses a wide range of punch sleeve surface roughness and textures. The ironing die and the punch tooling both can vary in the roughness from 0.04 μm to 0.4 μm Ra during the can forming process. This, together with the roughness of the incoming can body sheet (from 0.3 μm to 0.6 μm Ra) creates a wide range of tool/metal interface coefficients of friction. Ironing dies become rougher and have to be replaced frequently once they lose their shape. Punches maintain a consistent roughness for periods of a week to a month and any surface wear is compensated for with die changes. The initial die and punch surface finish adopted by a manufacturing unit determines the long time plant productivity and punch life. A higher friction on the punch side, compared to the die side, is the preferred manufacturing operating condition. Departures from the preferred condition with ground, polished, cross-hatch and media textured punches are examined. Plants that prefer polished carbide punches over cross-hatched must have their lubrication and coolant parameters controlled within a very narrow operating window. A larger operating window and better performance is achieved with the cross-hatch and micro-textured punches having a Ra less than half that of the can body sheet. Above all, a random isotropic texture is identified as the ideal punch sleeve surface texture and the best performer for aluminium can manufacture.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Preparation,microstructure and tribological behavior of laser cladding NiAl intermetallic compound coatings

Nickel aluminide (NiAl) intermetallic compound coatings were in situ synthesized from pre-placed mixed powders of Ni and Al by laser cladding. The phase composition and microstructure of the NiAl coatings were studied by means of X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The effects of laser cladding parameters on the microstructure and friction and wear behavior of the NiAl coatings were investigated. It has been found that laser power density had a crucial influence on the microstructure and friction and wear behavior of NiAl coatings. Namely, the NiAl coatings synthesized under a lower power density have more dense and fine microstructure, and lower friction coefficient and wear rate. Besides, the friction and wear behavior of the laser cladding NiAl coatings is highly dependent on applied normal load and sliding speed; and the resulting coatings sliding against Si₃N₄ in a ball-on-disc contact mode is more suitable for tribological application at a moderate normal load of 3–7 N and sliding speed of 0.16–0.21 m/s.     

Plastic deformation of 25CrMo4 steel during wear: Effect of the temperature,the normal force,the sliding velocity and the structural state

This article follows a previous study on friction and wear of 25CrMo4 steel [N. Khanafi-Benghalem, K. Loucif, E. Felder, F. Delamare, Influence de la température sur les mécanismes de frottement et d’usure des aciers X12NiCrMoSi25-20 et 25CrMo4 glissant sur du carbure de tungstène, Matériaux et techniques 93 (2005) 347–362]. The aim of our work is to study in more details the process of plastic deformation and the wear rate of this steel in lubricated sliding against cemented tungsten carbide, process observed in the previous work. The considered parameters are the temperature T (from 20 to 200 °C), the normal force P (from 500 to 1500 N), the steel structure (normalised HV 220 and quenched/tempered HV 480 states) and the sliding velocity v (from 0.05 to 0.3 m/s). We measured the friction coefficient and the sample total volume loss. A displacement sensor follows the volume loss evolution during the test; this follow-up is approximate because of the sample plastic flow which leads to the formation of peripheral burrs. All the tests conditions generate a significant plastic deformation of the sample steel, even in the quenched/tempered state: it produces a marked increase of the surface hardness, the work hardened layer being much finer for the quenched/tempered state (15 μm) than for the normalised state (40 μm at 20 °C). For temperatures T ≤ 100 °C in normalised state, the wear follows the Archard's law with an increasing rate with temperature. For T ≥ 120 °C, the wear rate decreases during the test, the global volume of wear being a decreasing function of T. For the quenched/tempered state, the wear rate decreases with the increase of the normal force, this decrease is less than 30% of the normalised state value. The material heating during the wear tests is well correlated with the friction dissipated power, but remains small, except in extreme cases (v maximum, great friction at high temperatures). These results suggest the existence of two wear mechanisms: abrasion by sample debris and burrs emission by plastic flow. The abrasion is probably the dominating mechanism for the tests carried out at the lowest temperatures. The plastic flow becomes a significant component at the highest temperatures. Using a contact model, we discuss to what extent the influence of the temperature and the strain rate on the steel hardness and ductility could explain the temperature and the sliding velocity effect on wear. Other phenomena are probably present: the influence of the steel microstructure and the lubricant on the size and/or the number of particles responsible for abrasion.     

Low wear metal sliding electrical contacts at high current density

Operation of a low wear (2 × 10^?5 mm³/(N-m)), low contact resistance copper sliding electrical contact was demonstrated. The wear rate of a lightly loaded copper–beryllium metal fiber sliding on a polished copper counterface was insensitive to (DC) current density values as great as 440 A/cm² (in a brush positive or anodic configuration). Low wear and relatively low friction (μ ～ 0.2 to 0.3) was achieved by operating the contact immersed in a liquid medium consisting of a hydrofluoroether with helium cover gas, inhibitingoxidationand providing cooling of the contact. Similar experiments performed in liquid mediums of ultrapure water and dilute (3%) hydrogen peroxide show an order of magnitude increase in wear rate and provide further insight on the role of electrochemically enhanced oxidation and the degraded contact resistance and tribological behavior of non-noble sliding electrical contacts in general. In contrast to high current density slidingin hydrofluoroether, an order of magnitude greater wear rate was observed for similar sliding conditionsin hydrogen peroxide or water without the aid of externally supplied electric potential. A conceptual model is proposed correlatingthe rate of brush wear to fatigue strength and electrochemically enhanced oxidation as a result of high current density transport through the contact. A mathematical expression was derived to calculate the approximate wear volume of a single fiber laterally contacting a slip-ring, based on direct measurement of the wear scar geometry.     

Effects of sliding velocity and normal load on friction and wear characteristics of multi-layered diamond-like carbon (DLC) coating prepared by reactive sputtering

Friction and wear tests were performed to investigate effects of sliding velocity and normal load on tribological characteristics of a multi-layered diamond-like carbon (DLC) coating for machine elements. The DLC coatings which consist of sequentially deposited gradient Cr/CrN, W-doped DLC (a-C:H:W) and DLC (a-C:H) layers were formed on carburized SCM 415 Cr–Mo steel disks using a reactive sputtering system. The tests against AISI 52100 steel balls were performed under various sliding velocities (0.0625, 0.125, 0.25, 0.5, 1 and 2 m/s) and normal loads (6.1, 20.7 and 49.0 N) in ambient air (relative humidity=26±2%, temperature=18±2 °C). Each test was conducted for 20 km sliding distance without lubricating oil. The results show that friction coefficients decrease with the increase in sliding velocity and normal load. Wear rates of both surfaces decrease with the increase in normal load. The increase in sliding velocity leads initially to the increase in wear rates up to the maximum value. Then, they decrease, as the sliding velocity increases above specific value that corresponds to the maximum wear rate. Through surface observation and analysis, it is confirmed that formation of transfer layers and graphitized degree of wear surfaces of DLC coatings mainly affect its tribological characteristics.     

Tribological behavior of PEEK components with compositionally graded PEEK/PTFE surfaces

PEEK is a high strength engineering thermoplastic that suffers from a high friction coefficient and a friction induced wear mode. Past studies with 10 μm PEEK and PTFE powders resulted in composite solid lubricant that (at the optimal composition) had a wear rate of k = 2 × 10⁻⁹ mm³/Nm with a friction coefficient of μ = 0.12. A compositional grading of PEEK and PTFE is implemented in this study to create a bulk composite with the functional requirements of component strength, stiffness and wear resistance while providing solid lubrication at the sliding interface. The tribological performances of three functionally graded PEEK components were evaluated on linear reciprocating, rotating pin-on-disk and thrust washer tribometers. Wear rates comparable to samples of the bulk solid lubricant and comparable or improved frictional performance were achieved by compositionally grading the near surface region of PEEK components.     

Improving tribological behaviour of piston ring–cylinder liner frictional pair by liner surface texturing

Experiments were carried out on a reciprocating tester. The lubricant was supplied into the inlet side of the contact zone. The construction of tribological tester allows to measure the friction force between specimen and counter-specimen. Tribological behaviours of cylinder liners with and without oil pockets were compared. Specimens were cut from plateau honed cylinder liners made of grey cast iron. Counter-specimens were cut from grey cast iron piston rings. A special tool acted as a hammer to form additional dimples on the liner surfaces. The area density of oil pockets was about 13%. Specimen surfaces had dimples with average depths about 5 μm and diameters in the range 0.15–0.2 mm. Two batches of tribological tests were carried out, in regimes of full and starved lubrication. Friction tests were conducted at three mean sliding speeds: 0.44, 0.66 and 0.88 m/s. Experiments were performed with normal load in the range 50–300 N, starting from the lowest load. Normal load increased in a stepwise manner after 2 min at each load, until the maximum load was reached. Areal surface topographies of specimens and counter-specimens were measured before and after two batches of tests by white light interferometer.     

The tribological characteristics of TiCN coating at elevated temperatures

The tribological behaviour of TiCN coating prepared by unbalanced magnetron sputtering is studied in this work. The substrates made from austenitic steel were coated by TiCN coatings during one deposition. The measurements were provided by high temperature tribometer (pin-on-disc, CSM Instruments) allowing measuring the dependency of friction coefficient on cycles (sliding distance) up to 500 °C. The evolution of the friction coefficient with the cycles was measured under different conditions, such as temperature or sliding speed and the wear rate of the ball and coating were evaluated. The 100Cr6 balls and the Si₃N₄ ceramic balls were used as counter-parts. The former were used at temperatures up to 200 °C, the latter up to 500 °C. The wear tracks were examined by optical methods and SEM. The surface oxidation at elevated temperatures and profile elements composition of the wear track were also measured.The experiments have shown considerable dependency of TiCN tribological parameters on temperature. Rise in temperature increased both friction coefficient and the wear rate of the coating in case of 100Cr6 balls. The main wear mechanism was a mild wear at temperatures up to 200 °C; fracture and delamination were dominating wear mechanisms at temperatures from 300 to 500 °C.     

Tribological behavior of natural fiber reinforced PLA composites

The application spectrum of natural fiber reinforced polymer composites is growing rapidly in various engineering fields. The present study explores the possibilities of reinforcing thermoplastic bio-polymer with locally available inexpensive plant fibers for developing a new tribo-material. Three different types of natural fibers (nettle, grewia optiva and sisal) were incorporated into PLA polymer to develop laminated composites using a hot compression technique. TGA analysis was carried out to investigate the thermal stability of developed composites. Wear and frictional characteristics of developed composites were investigated under dry contact condition at different operating parameters, such as applied load (10–30 N), sliding speed (1–3 m/s) and sliding distance (1000–3000 m). The experimental results indicate that incorporation of natural fiber mats into PLA matrix significantly improves the wear behavior of neat polymer. There was 10–44% reduction in friction coefficient and more than 70% reduction in specific wear rate of developed composites as compared to neat PLA. The worn surface morphology was studied using scanning electron microscope (SEM) to analyze the wear mechanism in different types of developed composites.     

Friction and wear durability studies on the 3D negative fingerprint and honeycomb textured SU-8 surfaces

The effects of two different textures (a 3D negative fingerprint texture and a honeycomb texture) on the tribological performance of SU-8 polymer surface have been investigated with a ball-on-disc tribometer. Friction and wear behaviors of the textured surfaces are conducted against a 4 mm diameter silicon nitride (Si₃N₄) ball counterface. The coefficient of friction for the negative fingerprint textured surface (μ=∼0.08) is much lower than that of the untextured surface (∼0.2) and the honeycomb textured surface (∼0.41) under a normal load of 100 mN and a rotational speed of 2 rpm. The coefficients of friction of the textured surfaces decrease with increasing normal loads between 100 mN and 300 mN. Above the normal load of 300 mN, the coefficient of friction of the negative fingerprint textured surface increases due to the occurrence of plastic deformation. The honeycomb textured surface has shown the highest coefficient of friction. The wear durability tests are also conducted at a normal load of 100 mN and a rotational speed of 500 rpm on the untextured/textured surfaces on SU-8 in the presence of an overcoat of a nano-lubricant, perfluoropolyether(PFPE). Six samples i.e. the untextured surface (Si/SU-8 and Si/SU-8/PFPE), the 3D negative fingerprint textured surface (Si/SU-8/FP and Si/SU-8/FP/PFPE) and the honeycomb textured surface (Si/SU-8/HC and Si/SU-8/HC/PFPE), each with and without PFPE nano-lubricant, have been investigated for their tribological behaviours. The negative fingerprint pattern on SU-8 with PFPE coating has shown the highest wear life of 60,000 cycles under a normal load of 100 mN. The reasons for excellent tribological performance of 3D fingerprinted SU-8 surface are analyzed using the Hertzian contact area calculation.     

Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites

The non-lubricated, sliding friction and wear behavior of Ti₃Si(Al)C₂ and SiC-reinforced Ti₃Si(Al)C₂ composites against AISI 52100 bearing steel ball were investigated using a ball-on-flat, reciprocating tribometer at room temperature. The contact load was varied from 5 to 20 N. For monolithic Ti₃Si(Al)C₂, high friction coefficients between 0.61 and 0.90 and wear rates between 1.79 × 10⁻³ and 2.68 × 10⁻³ mm³ (N m)⁻¹ were measured. With increasing SiC content in the composites, both the friction coefficients and the wear rates were significantly decreased. The friction coefficients reduced to a value between 0.38 and 0.50, and the wear rates to between 2.64 × 10⁻⁴ and 1.93 × 10⁻⁵ mm³ (N m)⁻¹ when the SiC content ranged from 10 to 30 vol.%. The enhanced wear resistance of Ti₃Si(Al)C₂ is mainly attributed to the facts that the hard SiC particles inhibit the plastic deformation and fracture of the soft matrix, the oxide debris lubricate the counterpair, and the wear mode converts from adhesive wear to abrasive wear during dry sliding.     

Tribological behavior of graphite-containing nickel-based composite as function of temperature,load and counterface

Nickel-based graphite-containing composites were prepared by powder metallurgy method. Their mechanical properties at room temperature and friction and wear properties from room temperature to 600 °C were investigated by a pin-on-disk tribometer with alumina, silicon nitride and nickel-based alloy as counterfaces. The effects of graphite addition amount, temperature, load, sliding speed and counterface materials on the tribological properties were discussed. The micro-structure and worn surface morphologies were analyzed by scanning electron microscope (SEM) attached with energy dispersive spectroscopy (EDS). The results show that the composites are mainly consisted of nickel-based solid solution, free graphite and carbide formed during hot pressing. The friction and wear properties of composites are all improved by adding 6–12 wt.% graphite while the anti-bending and tensile strength as well as hardness decrease after adding graphite. The friction coefficients from room temperature to 600 °C decrease with the increase of load, sliding speed while the wear rates increase with the increasing temperature, sliding speed. The lower friction coefficients and wear rates are obtained when the composite rubs against nickel-based alloy containing molybdenum disulfide. Friction coefficients of graphite-containing composites from room temperature to 600 °C are about 0.4 while wear rates are in the magnitude of 10^?5 mm³/(N m). At high temperature, the graphite is not effective in lubrication due to the oxidation and the shield of ‘glaze’ layer formed by compacting back-transferred wear particles. EDS analysis of worn surface shows that the oxides of nickel and molybdenum play the main role of lubrication instead of graphite at the temperature above 400 °C.