Relationship between the interfacial tension and compatibility of polycarbonate and poly(acrylonitrile–butadiene–styrene) blends with reactive compatibilizers

We studied the morphological, mechanical, and rheological properties of polycarbonate (PC) and poly(acrylonitrile–butadiene–styrene) (PolyABS) blends with different types of compatibilizer. Styrene–acrylonitrile–maleic anhydride terpolymer (SAM) was used as a compatibilizer of the blends. For comparison, styrene–acrylonitrile–glycidyl methacrylate terpolymer (SAG) was also used as a compatibilizer. For the PC–PolyABS (70/30 wt %) blends with SAM, the mechanical strength and complex viscosity reached a maximum when the SAM concentration was 5 phr. The mechanical and rheological results of the blend were consistent with the morphological result that the PolyABS domain size reached a minimum when the SAM content was 5 phr. The interfacial tension (α) of the blend was compared with the compatibilizer type and content, which were calculated by the Palierne emulsion model with the relaxation time of the PC–PolyABS blend. The α is consistent with the morphological and mechanical properties of the PC–PolyABS blend. The results of the morphological, mechanical, and rheological properties of the blend suggest that SAM was a more effective compatibilizer than SAG, and the optimum compatibilizer content of SAM was 5 phr. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46418.     

Melt rheology of nanometre‐calcium‐carbonate‐filled acrylonitrile–butadiene–styrene (ABS) copolymer composites during capillary extrusion

The melt flow properties during capillary extrusion of nanometre‐calcium‐carbonate‐filled acrylonitrile–butadiene–styrene (ABS) copolymer composites were measured by using a Rosand rheometer to identify the effects of the filler content and operation conditions on the rheological behaviour of the sample melts. The experiments were conducted under the following test conditions: temperature varied from 220 to 240 °C and shear rate ranged from 10 to 10⁴ s^?1. The filler volume fractions were 0, 10, 20, 30, 40 and 50%. The results showed that the shear flow did not strictly obey the power law under the test conditions, and that the entry pressure drop (ΔP_en) and the extension stress (σ_e) in entry flow increased nonlinearly, while the melt shear viscosity (η_s) and extension viscosity (η_e) decreased with increasing the wall shear stress (τ_w) at constant test temperature. The dependence of the melt shear viscosity on the test temperature was approximately consistent with the Arrhenius expression at fixed τ_w. When τ_w was constant, η_s and η_e increased while ΔP_en and σ_e decreased with the addition of the filler volume fraction. © 2002 Society of Chemical Industry     

Effects of extrusion conditions on rheological behavior of acrylonitrile–butadiene–styrene terpolymer melt

The influence of temperatures and flow rates on the rheological behavior during extrusion of acrylonitrile–butadiene–styrene (ABS) terpolymer melt was investigated by using a Rosand capillary rheometer. It was found that the wall shear stress (τ_w) increased nonlinearly with increasing apparent shear rates and the slope of the curves changed suddenly at a shear rate of about 10³ s^?1, whereas the melt‐shear viscosity decreased quickly at a τ_w of about 200 kPa. When the temperature was fixed, the entry‐pressure drop and extensional stress increased nonlinearly with increasing τ_w, whereas it decreased with a rise of temperature at a constant level of τ_w. The relationship between the melt‐shear viscosity and temperature was consistent with an Arrhenius expression. The results showed that the effects of extrusion operation conditions on the rheological behavior of the ABS resin melt were significant and were attributable to the change of morphology of the rubber phase over a wide range of shear rates. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 606–611, 2002     

Recycling of blends of acrylonitrile–butadiene–styrene (ABS) and polyamide

The aim of this work is to evaluate routes to upgrade recycled engineering plastics, especially mixed plastics with acrylonitrile–butadiene–styrene copolymers (ABS) as the major component. A core‐shell impact modifier was successfully used to improve the impact strength of blends of ABS and ABS/polycarbonate (PC) blends recycled from the automotive industry. However, the presence of other immiscible components like polyamide (PA), even in small amounts, can lead to a deterioration in the overall properties of the blends. A styrene–maleic anhydride (SMA) copolymer and other commercial polymer blends were used to promote the compatibilization of ABS and PA. The core‐shell impact modifier was again found to be an efficient additive with regard to the impact strength of the compatibilized ABS/PA blends. The results obtained with fresh material blends were quite promising. However, in blends of recycled ABS and glass‐fiber‐reinforced PA, the impact strength did not exhibit the desired behavior. The presence of poorly bonded glass fibers in the blend matrix was the probable reason for the poor impact strength compared with that of a blend of recycled ABS and mineral‐filled PA. Although functionalized triblock rubbers (SEBS–MA) can substantially enhance the impact strength of PA, they did not improve the impact strength of ABS/PA blends because the miscibility with ABS is poor. The possibilities of using commercial polymer blends to compatibilize otherwise incompatible polymer mixtures were also explored giving promising results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2535–2543, 2002     

Mechanical properties of acrylonitrile–butadiene–styrene copolymer/poly(l‐lactic acid) blends and their composites

As the material properties of acrylonitrile–butadiene–styrene copolymer (ABS) have an excessively wide margin for applications in automobile console boxes, ABS partly replaced with poly(l ‐lactic acid) (PLA) may be used for the same purpose with improved ecofriendliness if the corresponding deterioration of the material properties is acceptable through the choice of appropriate additives. ABS composites with 30 wt % renewable components (PLA and cellulose pulp) were prepared by melt compounding, and the material properties were examined as a function of the additive content. The changes in the mechanical properties of the ABS/PLA blends were examined after the addition of cellulose pulp and two clays [Cloisite 25A (C25A) and sodium montmorillonite] as well as these two clays treated with bis(3‐triethoxysilylpropyl)tetrasulfide (TESPT). The heat distortion temperatures of the composites were measured as a function of the content of the TESPT‐treated C25A. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40329.     

Properties of acrylonitrile–butadiene–styrene/polycarbonate blends with styrene–butadiene–styrene block copolymer

The importance of alloys and blends has increased gradually in the polymer industry so that the plastics industry has moved toward complex systems. The main reasons for making polymer blends are the strengthening and the economic aspects of the resultant product. In this study, I attempted to improve compatibility in a polymer blend composed of two normally incompatible constituents, namely, acrylonitrile–butadiene–styrene (ABS) and polycarbonate (PC), through the addition of a compatibilizer. The compatibilizing agent, styrene–butadiene–styrene block copolymer (SBS), was added to the polymer blend in ratios of 1, 5, and 10% with a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by scanning electron microscopy and differential scanning calorimetry. Further, all three blends of ABS/PC/SBS were subjected to examination to obtain their yield and tensile strengths, elasticity modulus, percentage elongation, Izod impact strength, hardness, heat deflection temperature, Vicat softening point, and melt flow index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2521–2527, 2004     

Mechanical and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer reinforced with potassium titanate whiskers

Potassium titanate (K₂Ti₆O₁₃) whisker treated with tetrabutyl orthotitanate was used to improve the mechanical and thermal properties of the poly(acrylonitrile–butadiene–styrene) (ABS) copolymer. The composites were prepared in a twin‐screw extruder followed by injection molding. Static tensile measurements showed that both the modulus and breaking stress of ABS/K₂Ti₆O₁₃ composites increase considerably with increasing whisker content; the strain at break of ABS was almost unaffected by the incorporation of a whisker content up to 15 wt %. Izod impact tests indicated that the composites showed a decrease in the impact strength with increasing whiskers content. Thermogravimetric analysis showed that the K₂Ti₆O₁₃ whisker additions have little effect on the thermooxidative stability of ABS. Scanning electron microscopic observations revealed that the whiskers were aligned along the melt‐flow direction in the thin surface layer, whereas the whiskers were oriented randomly as well as perpendicular to the injection direction in the thick core region of the composites. The Tsai–Halpin equation was used to evaluate the moduli of the ABS/K₂Ti₆O₁₃ composites. The theoretical calculations generally correlated well with the experiment data by assuming K₂Ti₆O₁₃ whiskers to have an aspect ratio of 12. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2985–2991, 1999     

Modification of poly(styrene) by reactive blending with nitrificated rubber

A possible way to obtain modified poly(styrene) (PS) with a new complex of properties: 2–3 times higher impact resistance in a combination with significantly increased tensile strength and bending strength, 6–8 times higher flowability and strongly increased adhesion is described here. It is established that the modified PS new properties complex is a result from an elastification, nitrification, structure modification, and “critical” phenomena in the two component system studied. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 638–645, 2001     

Blends of recycled polycarbonate and acrylonitrile–butadiene–styrene: comparing the effect of reactive compatibilizers on mechanical and morphological properties

Blends of recycled polycarbonate (PC) and acrylonitrile–butadiene–styrene (ABS) were prepared and some mechanical and morphological properties were investigated. To compatibilize these blends, ABS‐g‐(maleic anhydride) (ABS‐g‐MA) and (ethylene–vinyl acetate)‐g‐(maleic anhydride) (EVA‐g‐MA) with similar degree of grafting of 1.5% were used. To compare the effect of the type of compatibilizer on mechanical properties, blends were prepared using 3, 5 and 10 phr of each compatibilizer. A co‐rotating twin‐screw extruder was used for blending. The results showed that ABS‐g‐MA had no significant effect on the tensile strength of the blends while EVA‐g‐MA decreased the tensile strength, the maximum decrease being about 9.6% when using 10 phr of this compatibilizer. The results of notched Charpy impact strength tests showed that EVA‐g‐MA increased the impact strength of blends more than ABS‐g‐MA. The maximum value of this increase occurred when using 5 phr of each compatibilizer, it being about 54% for ABS‐g‐MA and 165% for EVA‐g‐MA. Scanning electron microscopy micrographs showed that the particle size of the dispersed phase was decreased in the continuous phase of PC by using the compatibilizers. Moreover, a blend without compatibilizer showed brittle behaviour while the blends containing compatibilizer showed ductile behaviour in fracture. © 2013 Society of Chemical Industry     

Polylactide toughening with epoxy‐functionalized grafted acrylonitrile–butadiene–styrene particles

Glycidyl methacrylate functionalized acrylonitrile–butadiene–styrene (ABS‐g‐GMA) particles were prepared and used to toughen polylactide (PLA). The characteristic absorption at 1728 cm^?1 of the Fourier transform infrared spectra indicated that glycidyl methacrylate (GMA) was grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Chemical reactions analysis indicated that compatibilization and crosslinking reactions took place simultaneously between the epoxy groups of ABS‐g‐GMA and the end carboxyl or hydroxyl groups of PLA and that the increase of GMA content improved the reaction degree. Scanning electron microscopy results showed that 1 wt % GMA was sufficient to satisfy the compatibilization and that ABS‐g‐GMA particles with 1 wt % GMA dispersed in PLA uniformly. A further increase of GMA content induced the agglomeration of ABS‐g‐GMA particles because of crosslinking reactions. Dynamic mechanical analysis testing showed that the miscibility between PLA and ABS improved with the introduction of GMA onto ABS particles because of compatibilization reactions. The storage modulus decreased for the PLA blends with increasing GMA content. The decrease in the storage modulus was due to the chemical reactions in the PLA/ABS‐g‐GMA blends, which improved the viscosity and decreased the crystallization of PLA. A notched impact strength of 540 J/m was achieved for the PLA/ABS‐g‐GMA blend with 1 wt % GMA, which was 27 times than the impact strength of pure PLA, and a further increase in the GMA content in the ABS‐g‐GMA particles was not beneficial to the toughness improvement. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Modification of acrylonitrile‐butadiene‐styrene terpolymer by graft copolymerization with maleic anhydride in the melt. II. Properties and phase behavior

The graft copolymerization of maleic anhydride (MAH) onto acrylonitrile‐butadiene‐styrene terpolymer (ABS) using dicumyl peroxide and benzoyl peroxide as the binary initiator and styrene as the comonomer in the molten state was described. The properties and phase morphologies of the modified products (ABS‐g‐MAH) were studied. The results indicate that the melt flow index (MFI) of ABS‐g‐MAH increases with the increase of MAH content, the initiator concentration, and the screw speed, whereas the MFI decreases with the increase of temperature. The impact strength and the percentage elongation of ABS‐g‐MAH both decreased and the tensile strength of ABS‐g‐MAH increased slightly as the grafting degree increased. The phase inversion behavior of the modified product was observed by transmission electron microscopy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2834–2839, 2004     

Characterization of rubber phase in acrylonitrile–butadiene–styrene polymers

The performances of rubber‐toughened polymers like acrylonitrile–butadiene–styrene (ABS) are strongly affected by the type and amount of rubber phase. Characterization of rubber phase is an effective method to predict and control the physical and mechanical behaviors of ABS materials. In this work, different methods have been employed to determine the amount of rubber phase in ABS polymers. The first method was based on thermogravimetry using a particular step degradation of the polymer. In the second method, characteristic absorption bands in the Fourier transform infrared spectra were used to make a calibration curve to determine the rubber content of unknown ABS samples. The third method was based on variation of heat capacity of ABS polymers with increasing the rubber phase content. In the fourth method, a two‐step solvent extraction followed by centrifuging was used to separate the rubber particles of different ABS samples. Separation of hardened rubber particles was used to study the size and size distribution of rubber particles. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Kinetic investigation of thermooxidative degradation of poly(vinyl chloride)/acrylonitrile–butadiene–styrene blends by isothermal thermogravimetric analysis

The thermal degradation of poly(vinyl chloride)/acrylonitrile–butadiene–styrene (PVC/ABS) blends of different compositions was investigated by means of isothermal thermogravimetric analysis at temperatures of 210°–240°C in flowing atmosphere of air. The Flynn equation, the method of stationary point, and kinetic equation using the Prout–Tompkins model proved to be satisfactory in describing the thermooxidative degradation in the range of 5–30% conversions. The apparent activation energy E and preexponential factor Z were calculated for all compositions of PVC/ABS blends. The ratios E/ln Z are constant for pure and modified PVC and point to the unique mechanism of degradation process. Upon increasing the ratio of ABS in the PVC/ABS blend up to 50%, only the rate of the process is changed; the mechanism remains unchanged. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 833–839, 1999     

Preparation of poly(acrylonitrile–butadiene–styrene)/montmorillonite nanocomposites and degradation studies during extrusion reprocessing

In this study, the preparation of organically modified montmorillonite/poly(acrylonitrile–butadiene–styrene) (ABS) nanocomposites was studied by melt blending in a twin‐screw extruder. The composite material was subjected to a series of five extrusion cycles, and the effect of reprocessing on the material's structural properties was investigated. More specifically, chemical changes were studied with attenuated total reflectance/Fourier transform infrared analysis, the thermal response was recorded by differential scanning calorimetry experiments, and the thermal stability was detected with thermogravimetric analysis. Also, the rheological properties of these blends were investigated via melt flow index tests as a measure of their processability during melt mixing and molding processes. Furthermore, the mechanical strength of the obtained mixtures was explored, and the observed interactions were interpreted in terms of the influence of each component on the functional properties of the final mixture. This attempt enriched our knowledge about the recycling of ABS, with the additional aspect of the use of collected data from more complex systems, that is, composite materials, where the montmorillonite nanoparticles play a role in the interactions initiated by repeated processing. The experimental results of this study show that the reprocessing of ABS/montmorillonite induced oxidation products, but the rheological, mechanical, and thermal properties and the thermal and color stabilities of the composites remained almost stable. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Effect of styrene–isopren–styrene addition on the recycled polycarbonate/acrylonitrile–butadiene–styrene polymer blends

Interfacial agents as compatibilizers have recently been introduced into polymer blends to improve microstructure and mechanical properties of thermoplastics. In this way, it is possible to prepare a mixture of polymeric materials that can have superior mechanical properties over a wide temperature range. In this study, an incompatible blend of Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) Copolymer were made compatible by addition of 5, 10, and 20% Styrene–Isopren–Styrene Copolymer (SIS). The mixing operation was conducted using a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by SEM and DSC techniques. Furthermore, the elastic modulus, tensile and yield strengths, percentage elongation, hardness, melt flow index, Izod impact resistance, heat deflection temperature (HDT), Vicat softening point values of polymer alloys of various ratios were determined. It was found that addition of SIS to the structures decreased the tensile strength, yield strength, elastic modulus, and hardness, whereas it increased Izod impact strength and percentage elongation values. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 559–566, 2006     

Gloss reduction and morphological properties of polycarbonate and poly(methyl methacrylate‐acrylonitrile‐butadiene‐styrene) blends with SAN‐co‐GMA as a reactive compatibilizer

The gloss properties of the polycarbonate (PC)/poly(methyl methacrylate‐acrylonitrile‐butadiene‐styrene) (MABS) blend with styrene‐acrylonitrile‐co‐glycidyl methacrylate (SAN‐co‐GMA) as a compatibilizing agent were investigated. For the PC/poly(MABS)/SAN‐co‐GMA (65/15/20, wt %) blend surface, the reduction of gloss level was observed most significantly when the GMA content was 0.1 wt %, compared with the blends with 0.05 wt % GMA or without GMA content. The gloss level of the PC/poly(MABS)/SAN‐co‐GMA (0.1 wt % GMA) blend surface was observed to be 35, which showed 65% lower than the PC/poly(MABS)/SAN‐co‐GMA blend without GMA content. The gloss reduction was most probably caused by the insoluble fractions of the PC/poly(MABS)/SAN‐co‐GMA blend that were formed by the reaction between the carboxylic acid group in poly(MABS) and epoxy group in SAN‐co‐GMA. The results of optical and transmission electron microscope analysis, spectroscopy study, and rheological properties supported the formation of insoluble structure of the PC/poly(MABS)/SAN‐co‐GMA blend when the GMA content was 0.1 wt %. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46450.     

High-performance poly(lactic acid)/starch materials prepared via starch surface modification and its in situ enhancement

High-performance modified poly(lactic acid) (PLA)/starch (ST) blends were prepared by incorporating silane coupling agent. The coupling agent acted as a bridge between PLA and ST components, enhancing their interfacial compatibility during the melt blending. The addition of epoxy-functionalized silane coupling agent improved the interfacial adhesion between PLA and ST phases, as evidenced by the decreased number and spacing of gaps between the ST particles and PLA matrix. The coupling agent also filled the surface crack of the ST particles, improving their dispersion in PLA matrix. The tensile strength of the modified PLA/ST blend increased from 19.6 MPa for the neat PLA/ST blend to 53.4 MPa, exceeding that of neat PLA. The modified blend also showed improved hydrophobicity and thermal stability. This research presented an effective approach to reducing the cost of PLA-based materials and improving the performance of ST-filled PLA materials by enhancing the interfacial adhesion between ST and PLA through surface modification with silane coupling agent. It provided a simple and feasible strategy for the high-performance modification of polyester/ST materials.     

Tailoring the morphology and properties of poly(lactic acid)/poly(ethylene)‐co‐(vinyl acetate)/starch blends via reactive compatibilization

Poly(lactic acid)/poly(ethylene‐co‐vinyl acetate)/starch (PLA/EVA/starch) ternary blends were prepared by multi‐step melt processing (reactive extrusion) in the presence of maleic anhydride (MA), benzoyl peroxide and glycerol. The effects of MA and glycerol concentration on the morphology and properties of the PLA/EVA/starch blends were studied using scanning electron microscopy, transmission electron microscopy, atomic force microscopy, the Molau experiment, dynamic mechanical thermal analysis and differential scanning calorimetry etc. The plasticization and compatibilization provided a synergistic effect to these blends accompanied by a significant reduction in starch particle size and an increase in interfacial adhesion. Starch was finely dispersed in the ternary blends with a dimension of 0.5 ? 2 µm. Furthermore, EVA‐coated starch or a starch‐in‐EVA type of morphology was observed for the reactively compatibilized PLA/EVA/starch blends. The EVA with starch gradually changed into a co‐continuous phase with increasing MA concentration. Consequently, the toughness of the blends was improved. Since property stability of starch is an issue, the tensile properties of these blends were measured after different storage times and the blends showed good property stability. Copyright © 2012 Society of Chemical Industry     

Blends of acrylonitrile–butadiene–styrene/waste poly(ethylene terephthalate) compatibilized by styrene maleic anhydride

Waste poly(ethylene terephthalate) (PET) from thin bottles was blended with acrylonitrile–butadiene–styrene (ABS) copolymer in different proportions, up to 10 wt %. Styrene maleic anhydride (SMA) copolymer was used as a compatibilizer. The tensile strength and heat deflection temperature of the blend were higher than that of virgin ABS. Flexural modulus remained unaffected, although a slight decrease in impact property was observed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2593–2599, 2001