Temperature‐dependent transition of crystal phases in the electrospinning process of poly(vinylidene fluoride‐co‐hexafluoropropylene)

The temperature‐dependent transition of the crystal phases of poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) was investigated in the electrospinning process. A solution of PVDF‐HFP in N,N‐dimethyl acetamide (DMAc) produced only the β‐phase‐dominant crystal up to 70 °C, irrespective of the spinneret temperature. In a mixed solvent of DMAc and acetone, however, the crystal phase of the electrospun fibers was dependent on temperature: β‐phase‐dominant at 30 and 50 °C and α‐phase‐dominant at 70 °C. The transition was related to a change of the coagulation rate during electrospinning, because the less perfect α phase is preferable to the β phase at a higher coagulation rate. The temperature‐dependent increase of the coagulation rate was more drastic in the presence of acetone, so the transition took place only in the mixed solvent. At elevated temperature, acetone not only raised the evaporation rate of the solvent but promoted the phase separation of the polymer resulting from the lower critical solution temperature behavior, which was rheologically traced. © 2019 Society of Chemical Industry     

Effect of hot‐press on electrospun poly(vinylidene fluoride) membranes

Poly(vinylidene fluoride) (PVDF) was electrospun into ultrafine fibrous membranes from its solutions in a mixture of N,N‐dimethylformamide and acetone (9:1, v/v). The electrospun membranes were subsequently treated by continuous hot‐press at elevated temperatures up to 155°C. Changes of morphology, crystallinity, porosity, liquid absorption, and mechanical properties of the membranes after hot‐press were investigated. Results of scanning electron microscopy showed that there were no significant changes in fibrous membrane morphology when the hot‐press temperature varied from room temperature to 130°C, but larger pores were formed because of fibers melting and bonding under higher temperatures. Analyses of X‐ray diffraction and differential scanning calorimeter exhibited that the crystalline form of PVDF could transfer from β‐type to α‐type during hot‐press at temperatures higher than 65°C. Tensile tests suggested that the mechanical properties of the electrospun PVDF membranes were remarkably enhanced from 25 to 130°C, whereas the porosity and the liquid absorption decreased. The hot‐press at 130°C was optimal for the electrospun PVDF membranes. The continuous hot‐press post‐treatment could be a feasible method to produce electrospun membranes, not limited to PVDF, with suitable mechanical properties as well as good porosity and liquid absorption for their applications in high‐quality filtrations or battery separators. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Coaxial electrospun nanofibers of poly(vinylidene fluoride)/polyaniline filled with multi‐walled carbon nanotubes

Core‐shell nanofibers of poly (vinylidene fluoride)/polyaniline/multi‐walled carbon nanotubes (PVDF/PANi/MWCNTs) have been produced using the coaxial electrospinning technique. The nanofibers were semiconductive and had better piezoelectric properties than pure PVDF nanofibers. Piezoelectric PVDF nanofibers are capable of converting mechanical energy into electrical energy, which can be stored in charge storage devices. However, PVDF is not conductive and therefore, a conductive associate material is needed to transfer accumulated static charges into the capacitor. Fourier Transform Infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC) were carried out to study the crystalline β‐phase of PVDF. There was an increase in β‐phase in the electrospun PVDF nanofibers filled with MWCNTs as compared with compression molded samples of neat PVDF. Incorporation of PANi as an intrinsically conductive polymer (ICP) and MWCNTs as conductive nanofiller helps the movement of static charges. Core‐shell nanofibers had conductivities of about seven orders of magnitude higher than simple electrospun nanofibers. POLYM. COMPOS., 35:1198–1203, 2014. © 2013 Society of Plastics Engineers     

Morphology,polymorphism, and metal ion adsorption studies of electrospun nanofibers based on PVDF and organically modified layered double hydroxide

Nonwoven nanofiber mats of polyvinylidene fluoride (PVDF) with modified layered double hydroxide (MLDH) were prepared by electrospinning. The fiber morphology was studied using scanning electron microscopy. X‐ray diffraction and FTIR spectroscopy was used to characterize the polymorphism in electrospun mats. Fibers of diameter in the range 80–800 nm with beads of about 2–3 µm size were observed for pure PVDF, while in case of PVDF/MLDH nanocomposites the number and size of beads were found to be significantly reduced. Uniform and fine nanofibers were obtained at lower content of MLDH, but slightly rough surface was seen for higher content. FTIR and X‐ray diffraction patterns signify various crystalline forms of electrospun PVDF. The content of polar β‐crystalline phase of PVDF, which exhibit piezo and ferroelectric properties was found to be enhanced significantly due to reinforcement of MLDH. Use of these nanofiber mats for heavy metal Cu (II) removal was explored. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4508–4515, 2013     

Reinforcement of electroactive characteristics in polyvinylidene fluoride electrospun nanofibers by intercalation of multi-walled carbon nanotubes

This research work reports on development and characterization of multi-walled carbon nanotube (MWCNT)-doped polyvinylidene difluoride (PVDF) nanofibers by the electrospinning method. PVDF is an extensively studied polymer both theoretically and experimentally due to its appealing ferroelectric, piezoelectric, and pyroelectric properties which strongly favors its promising applications in the development of micro/nanostructure devices. The foremost reason for its ferroelectric and piezoelectric behaviors has been attributed to its crystalline structure, specifically the presence of β-phase; however, the existence of the small percentage of β-phase in pristine PVDF limits its applications. To enhance the electroactive features in the PVDF, MWCNTs have been doped in it to prepare electrospun nanofibers, as electrospinning is a single-step approach. These nonwoven nanofibers were prepared at a DC voltage of 20 kV which were subsequently calcined at 100 °C for 12 h. The estimation of crystal structure and phase identification in these nanofibers have been determined by attenuated FT-IR and XRD, while the morphology, microstructure, mean diameter, and length have been examined by FE-SEM. The observed electrical conductivity, capacitance, permittivity (ε), conductivity (δ), and impedance (Z) in these samples have been tailored by doping a range of MWCNT contents and optimizing the experimental conditions.     

Enhancement of β‐Phase Crystalline Structure and Piezoelectric Properties of Flexible PVDF/Ionic Liquid Surfactant Composite Nanofibers for Potential Application in Sensing and Self‐Powering

Polyvinylidene fluoride (PVDF) is a piezo‐polymer which among its crystalline phases, the β‐phase has been researched for the improvement of piezoelectric properties. In this study, to improve the β‐phase contents and thereby the piezoelectric response of the polymer, the effect of adding self‐synthesized ionic liquid surfactant (ILS) in PVDF nanofibers is studied. This material is added in different weight percentages into the PVDF solution and the nanofibers are produced by electrospinning to prepare active piezoelectric thin layers. SEM, XRD, FTIR, and piezo‐tests are employed for assessing the effect of the ILS on the enhancement of β‐phase in electrospun nanofibers and their piezoelectric performance. The results indicate ≈98.6% β‐phase formation in the sample containing 4 wt% ILS and in comparison with the pure nanofibers, the output voltage and its power density are improved 186.9% and 275%, respectively. Considering the results, it is suggested that the ILS can improve the piezoelectric response of the polymer in the fabricated structure by simple mixing in solution compared to other additives.     

Electrospun Antimicrobial PVDF‐DTAB Nanofibrous Membrane for Air Filtration: Effect of DTAB on Structure,Morphology, Adhesion,and Antibacterial Properties

Antimicrobial polyvinylidene fluoride (PVDF) membrane modified by dodecyltrimethyl ammonium bromide (DTAB) has been electrospun using simple one‐step technology, where the modifying agent DTAB is dissolved in spinning solution. X‐ray photoelectron spectroscopy and electrokinetic analysis confirm reliably the presence of DTAB on the nanofibers surfaces; electrokinetic analysis shows the changes of zeta potential due to modification by DTAB. X‐ray diffraction shows that electrospinning converts the part of α phase (≈40%) present in PVDF powder into β phase with all trans (TTT) zigzag chains conformation in PVDF electrospun membrane. Surface modification does not affect the phase composition of PVDF nanofibers, just only leads to lower crystallinity (smaller size of crystallites) in PVDF nanofibers. DTAB causes the curling of fibers and their aggregation, what completely changed the membrane structure. DTAB‐modified membrane exhibits antibacterial properties against Staphylococcus aureus subsp. Aureus. Concentration of 0.5 wt% DTAB in spinning solution causes partial inhibition of bacterial growth only, while 1.0 wt% concentration leads to complete inhibition.     

Facile and effective promotion of β crystalline phase in poly(vinylidene fluoride) via the incorporation of imidazolium ionic liquids

In this study, a facile and efficient protocol to enhance the β‐phase content of poly(vinylidene fluoride) (PVDF) is developed, in which the effect of room temperature ionic liquids (RTILs), including [1‐butyl‐3‐methylimidazolium (bmim)][PF₆], [bmim][BF₄], [bmim][FeCl₄] and [bmim][Cl], on the crystallization behavior of PVDF is investigated. The resulting PVDF/RTIL hybrids are characterized by Fourier transform infrared (FTIR) spectroscopy, XRD, polarized optical microscopy (POM) and DSC. The FTIR spectroscopy and XRD results show that the fraction of β‐phase, F(β), is significantly enhanced by the incorporation of RTILs, specifically from 49.2% for neat PVDF to 92.6% for hybrid filled with 15 wt% [bmim][PF₆]. The analysis of the crystallization behavior based on the DSC tests reveals that the degree of crystallinity increases with incorporation of RTILs, implying that RTILs could act as directing agents to facilitate the crystallization process, which is further evidenced by the POM results. In addition, the non‐isothermal crystallization kinetics of PVDF and PVDF/RTIL composites are investigated by means of DSC and the results indicate that the addition of the RTILs significantly influences the mechanism of nucleation and growth of PVDF crystallites. © 2013 Society of Chemical Industry     

Transparent poly(methyl methacrylate‐co‐butyl acrylate) nanofibers

Nanofibers of n‐Butyl Acrylate/Methyl Methacrylate copolymer [P(BA‐co‐MMA)] were produced by electrospinning in this study. P(BA‐co‐MMA) was synthesized by emulsion polymerization. The structural and thermal properties of copolymers and electrospun P(BA‐co‐MMA) nanofibers were analyzed using Fourier transform infrared spectroscopy–Attenuated total reflectance (FTIR–ATR), Nuclear magnetic spectroscopy (NMR), and Differential scanning calorimetry (DSC). FTIR–ATR spectra and NMR spectrum revealed that BA and MMA had effectively participated in polymerization. The morphology of the resulting nanofibers was investigated by scanning electron microscopy, indicating that the diameters of P(BA‐co‐MMA) nanofibers were strongly dependent on the polymer solution dielectric constant, and concentration of solution and flow rate. Homogeneous electrospun P(BA‐co‐MMA) fibers as small as 390 ± 30 nm were successfully produced. The dielectric properties of polymer solution strongly affected the diameter and morphology of electrospun polymer fibers. The bending instability of the electrospinning jet increased with higher dielectric constant. The charges inside the polymer jet tended to repel each other so as to stretch and reduce the diameter of the polymer fibers by the presence of high dielectric environment of the solvent. The extent to which the choice of solvent affects the nanofiber characteristics were well illustrated in the electrospinning of [P(BA‐co‐MMA)] from solvents and mixed solvents. Nanofiber mats showed relatively high hydrophobicity with intrinsic water contact angle up to 120°. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4264–4272, 2013     

On the electrospinning of PVDF: influence of the experimental conditions on the nanofiber properties

The characteristics of poly(vinylidene fluoride) (PVDF) nanofibers, prepared by applying the electrospinning technique from N,N‐dimethylformamide/acetone mixtures, were studied by varying the experimental conditions. The nanofiber morphology was assessed by scanning electron microscopy, while wide angle X‐ray diffraction and infrared spectroscopy were performed to study the crystallinity. The influence of the electrospinning conditions, such as kind of solvent mixture, polymer concentration, voltage tension, airflow and humidity, on nanofiber morphology was studied. In particular, the latter parameter, generally not considered, was found to modify the electrospun mat structure in a relevant way. Generally, the above technique turns out to be capable of strongly affecting the polymorphism of the polymer, namely β phase formation was higher in the electrospun mats compared with cast films, which displayed a non‐polar α crystal phase. As far as the influence of the electrospinning conditions on PVDF crystal structure is concerned, modification of the experimental parameters did not affect the α/β ratio. Nevertheless, comparing the behavior of two commercial PVDF samples with similar molecular masses, our results show that the polymer which forms a higher content of β phase in its cast films allowed electrospun mats characterized by almost complete formation of β phase to be obtained. Copyright © 2012 Society of Chemical Industry     

A new approach for conductive network formation in electrospun poly(vinylidene fluoride) nanofibers

Conductive nanofibers of poly(vinylidene fluoride) (PVDF) filled with polyaniline (PANi)‐coated multi‐wall carbon nanotubes (MWCNTs) were fabricated using the electrospinning technique. PANi is an intrinsically conductive polymer. The addition of PANi‐coated MWCNTs to PVDF created short conductive strands on the surface of the nanofibers, facilitating the formation of a conductive network in the transverse direction of the nanofibers. Piezoelectricity along with electric conductivity makes these PVDF nanofibers promising for applications such as sensors and actuators. Electrospun PVDF nanofiber mats had higher piezoelectricity than melt‐processed samples produced using traditional polymer processing techniques, such as compression molding. Spectroscopic imaging techniques were employed to study the effects of the filler and processing conditions on the nanofiber structure. X‐ray diffraction, Fourier transform infrared spectroscopy and differential scanning calorimetry results indicated a large increase in the β‐phase crystals of the PVDF nanofibers. This higher content of β‐phase crystals enhanced the piezoelectricity of the nanofibers. © 2015 Society of Chemical Industry     

Modification of electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) membranes through the introduction of poly(ethylene glycol) dimethacrylate

For the modification of an electrospun poly (vinylidene fluoride‐co‐hexafluoropropylene) (PVDF–HFP) membrane for its potential use as an electrolyte or separator in lithium batteries, poly(ethylene glycol) dimethacrylate (PEGDMA) was introduced into a polymer solution for electrospinning. A post heat treatment of the as‐electrospun membrane at an elevated temperature was performed for PEGDMA polymerization, and this was verified by Fourier transform infrared spectroscopy. The results showed that no significant variations in the membrane morphology were detected when a small amount of PEGDMA (PVDF–HFP/PEGDMA mass ratio = 4/1) was incorporated. This electrospun membrane after heat treatment at 130°C for 2 h exhibited a significantly higher tensile strength (6.26 ± 0.22 MPa) than that of an electrospun PVDF–HFP membrane (3.28 ± 0.35 MPa) without PEGDMA. The porosity and liquid absorption of the electrospun PVDF–HFP/PEGDMA (4/1) membrane were 70.0 ± 1.6% and 267 ± 11%, respectively, lower than those of the electrospun PVDF–HFP membrane (76.5 ± 0.3% and 352 ± 15%) because of the introduction of PEGDMA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polymorphism and crystallization in poly(vinylidene fluoride)/ poly(ϵ‐caprolactone)–block–poly(dimethylsiloxane)–block–poly(ϵ‐caprolactone) blends

The miscibility, crystallization kinetics and crystalline morphology of a new system of poly(vinylidene fluoride)/poly(?‐caprolactone)‐block‐poly(dimethylsiloxane)‐block‐poly(?‐caprolactone) (PVDF/PCL‐b‐PDMS‐b‐PCL) triblock copolymer were investigated by a variety of techniques. The miscibility and phase behaviour of PVDF/PCL‐b‐PDMS‐b‐PCL were studied by determination of the melting point temperature, crystallization kinetics and Fourier transform infrared (FTIR) mapping. Chemical imaging was used as a new technique to characterize the interaction of polymer blends in crystalline morphology. The results demonstrate the existence of characteristic peaks of both PVDF and PCL in the chosen crystalline area. The crystalline structures of PVDF were affected by the PCL‐b‐PDMS‐b‐PCL triblock copolymer and facilitate the formation of the β polymorph which was illustrated by FTIR analysis. The β crystal phase fraction increases significantly on increasing the composition of the PCL‐b‐PDMS‐b‐PCL triblock copolymer. In addition, confined crystallization of PCL within PVDF inter‐lamellar and/or inter‐fibrillar regions was confirmed through polarizing optical microscopy, wide‐angle X‐ray diffraction and small‐angle X‐ray scattering analysis. © 2019 Society of Chemical Industry     

Effect of multi‐walled carbon nanotubes on crystallization,thermal, and mechanical properties of poly(vinylidene fluoride)

Composites were prepared by solution blending poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWNTs). Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) results showed that the crystalline structure of PVDF was changed by the addition of MWNTs and a MWNTs‐induced crystal transformation from α‐phase to β‐phase of PVDF was confirmed. With differential scanning calorimeter (DSC) and dynamic mechanic thermal analysis (DMA) techniques, thermal and mechanical properties of the composite films were examined. As the DSC results showed, addition of MWNTs would lead to the increased cooling crystallization temperature (T_c), implying that MWNTs nanoparticles could act as nucleating agents, which is further proved with the help of polarized optical microphotographs. On the other hand, the decreasing of D_d (degree of crystallinity) implied that the MWNTs networks can confine the crystallization of PVDF. Through the curve analysis of the dynamic mechanical measurements, it was found that the storage modulus (E′) is significantly enhanced, revealing that a strong interaction should exist between PVDF and MWNTs. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

The structure characterization of thermosensitive poly(N‐isopropylacrylamide‐co‐2‐hydroxypropyl methacrylate) hydrogel

The goal of this work was to investigate a possible way of crosslinking polymer chains and the potential formation of intramolecular hydrogen bonds in thermosensitive poly(N‐isopropylacrylamide‐co‐2‐hydroxypropyl methacrylate) (p(NIPAM‐HPMet)) hydrogels obtained by radical polymerization. The chemical structure of the synthesized hydrogels was investigated by Fourier transform infrared (FTIR) spectroscopy and XRD. The FTIR spectrum confirmed the presence of hydrogen bonds formed between the chains in the copolymer. XRD analysis confirmed the amorphous ? crystalline structure of the copolymer. A three‐glass transition and two melting temperatures were detected by DSC. It was found that the addition of HPMet increased the glass transition and melting temperatures of the p(NIPAM‐HPMet) copolymer. The swelling transport mechanism of p(NIPAM‐HPMet) changed from non‐Fickian at 20 °C to case III or zero‐order time‐independent kinetics characterized by a linear mass uptake with time with increasing temperature at 40 °C. © 2013 Society of Chemical Industry     

Effect of nanoclay on the thermal,mechanical, and crystallization behavior of nanofiber webs of nylon‐6

Nylon‐6 and nanoclay/nylon‐6 composite nanofibers were prepared by electrospinning technique, in which formic acid was used as a solvent for good solubility of nylon‐6. The diameter of nylon‐6 and nanoclay/nylon‐6 nanofibers was below 350 nm and had smooth surfaces. The DSC heating curves of nylon‐6 and composites nanofibers show two endotherm behaviors, T_m1 (about 214°C) and T_m2 (about 220°C), corresponding to the melting events of γ‐form and α‐form crystals, respectively. The WAXs study showed that the γ‐crystalline phase predominantly present in both nylon‐6 and nanoclay/nylon‐6 nanofibers. The mechanical properties of the nanoclay/nylon‐6 composite nanofibers were higher than neat nylon‐6 electrospun nanofibers, which was decreased as the quantity of the clay increased. It might be due to the aggregation of nanoclay at high concentration. The thermal properties of the composite nanofibers were higher than neat nylon‐6 nanofibers. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Effect of solvents on morphology and polymorphism of polyvinylidene fluoride membrane via supercritical CO2 induced phase separation

Poly vinylidene fluoride (PVDF) membranes were prepared via supercritical CO₂ induced phase separation. The effects of solvent power on PVDF membrane morphology and polymorphism were investigated using N‐N‐dimethylformamide (DMF), triethyl phosphate (TEP), and their mixture respectively. The morphology evolution including cross‐section and surfaces were thoroughly studied by scanning electron microscope (SEM) and atomic force microscopy (AFM). The differences of solubility parameters between the solvent and PVDF affected the phase separation and the resultant morphology. The various crystalline phases of the membranes were mainly investigated by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffractometer (XRD). Solvent with larger dipole moment tended to form polar β phase. Decreasing the difference of solubility parameters favored the formation of α phase. Furthermore, the effects of salt additive on PVDF membrane morphology and crystalline form were studied as well. Results turned out that lithium chloride (LiCl) induced a porous top surface and boosted the formation of β phase. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41065.     

Electrospun nylon 6 nanofibers incorporated with 2‐substituted N‐alkylimidazoles and their silver(I) complexes for antibacterial applications

The article presents the incorporation of biocides [2‐substituted N‐alkylimidazoles and their silver(I) complexes] into electrospun nylon 6 nanofibers for application as antimicrobial materials. The electrospun nylon 6/biocides nanofiber composites were characterized by IR spectroscopy (ATR‐FTIR) and scanning electron microscopy (SEM‐EDX). The antimicrobial activity of the electrospun nylon 6/biocides nanofiber composites was evaluated against Escherichia coli, Staphylococcus aureus, and Bacillus subtilis subsp. spizizenii using the disk diffusion method, the American Association for Textile Chemists and Colorists test method 100‐2004 and the dynamic shake flask method (American Society for Testing and Materials E2149‐10). The electrospun nylon 6 nanofibers incorporated with 2‐substituted N‐alkylimidazoles displayed moderate to excellent levels of growth reduction against S. aureus (73.2–99.8%). For the electrospun nylon 6 nanofibers incorporated with silver(I) complexes, the levels of growth reduction were >99.99%, for both E. coli and S. aureus, after the antimicrobial activity evaluation using the shake flask method. The study demonstrated that the electrospun nanofibers, fabricated using the incorporation strategy, have the potential to be used as attractive antimicrobial materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39783.     

Crystal polymorphism in electrospun composite nanofibers of poly(vinylidene fluoride) with nanoclay

We investigated for the first time the morphology and crystal polymorphism of electrospun composite nanofibers of poly(vinylidene fluoride) (PVDF) with two nanoclays: Lucentite™ STN and SWN. Both nanoclays are based on the hectorite structure, but STN has organic modifier in between the layers of hectorite while SWN does not. PVDF/nanoclay was dissolved in N,N-dimethylformamide/acetone and electrospun into composite nanofiber mats with fiber diameters ranging from 50-800 nm. Scanning electron microscopy shows that addition of STN and SWN can greatly decrease the number of beads and make the diameter of the nanofibers more uniform due to the increase of electrospinning solution conductivity brought by the nanoclay. Infrared spectroscopy and X-ray diffraction confirm that both STN and SWN can induce more extended PVDF chain conformers, found in beta and gamma phase, while reducing the alpha phase conformers in electrospun PVDF/Nanoclay composite nanofibers. With the attached organic modifier, even a small amount of STN can totally eliminate the non-polar alpha crystal conformers while SWN cannot. The ionic organic modifier makes STN much more effective than SWN in causing crystallization of the polar beta and gamma phases of PVDF. An ion-dipole interaction mechanism, suggested by Ramasundaram, et al. is utilized to explain the crystal polymorphism behavior in electrospun PVDF/nanoclay composite nanofibers.     

Influence of additive on structure of PVDF nanofibers electrospun via new spinneret design

Surface morphology and internal structure of polyvinylidene fluoride (PVDF) nanofibers were investigated in this study. PVDF nanofibers were electrospun by two types of spinnerets, nozzle and channel spinneret, with different contents of tetrabutylammonium chloride (TBAC) and at various take‐up velocities. The new spinneret design, channel spinneret, resulted in thicker fibers while high β‐phase content and small d‐spacing were obtained, especially in the case of low TBAC content. And high TBAC content led to finer PVDF nanofibers with high β‐phase content and small d‐spacing compared to low TBAC content regardless of spinneret types, while an increase in take‐up velocity did not have significant effect on both morphology and internal structure of PVDF nanofibers regardless of TBAC content. It suggests that electrostatic drawing acted dominantly rather than mechanically drawing in the system cooperating TBAC. However, the decreasing difference between two types of spinnerets was observed in terms of β‐phase content with an increase in TBAC content. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1752–1758, 2013