AlGaN/GaN背对背肖特基二极管氢气传感器

通过溅射的方法制作了Pt/AlGaN/GaN背对背肖特基二极管并测试了该器件对氢气的响应.研究了Pt/AlGaN/GaN背对背肖特基二极管在25和100℃时对于10%H2(N2气中)的响应,计算了器件的灵敏度;并比较了两种温度条件下器件对于氢气响应的快慢;空气中的氧气对于器件电流的恢复有重要的作用;最后由热电子发射公式计算了器件在通入10%的氢气前后有效势垒高度的变化.     

AlGaN/AlN/GaN肖特基二极管的电学性能

利用金属有机化学气相淀积(MOCVD)方法生长的AlGaN/AlN/GaN/蓝宝石材料制备了AlGaN肖特基二极管.器件的肖特基接触和欧姆接触分别为Ti/Pt和Ti/Al/Ti/Au,均采用电子束蒸发的方法沉积.AlGaN表面欧姆接触的比接触电阻率为7.48×10-4Ω/cm2,器件的I-V测试表明该AlGaN肖特基二极管具有较好的整流特性.根据器件的正向,I-V特性计算得到器件的势垒高度和理想因子分别为0.57eV和4.83.将器件在300℃中温退火,器件的电学性能有所改善.     

AlGaN/AlN/GaN肖特基二极管的电学性能

利用金属有机化学气相淀积(MOCVD)方法生长的AlGaN/AlN/GaN/蓝宝石材料制备了AlGaN肖特基二极管.器件的肖特基接触和欧姆接触分别为Ti/Pt和Ti/Al/Ti/Au,均采用电子束蒸发的方法沉积.AlGaN表面欧姆接触的比接触电阻率为7.48×10-4Ω/cm2,器件的I-V测试表明该AlGaN肖特基二极管具有较好的整流特性.根据器件的正向,I-V特性计算得到器件的势垒高度和理想因子分别为0.57eV和4.83.将器件在300℃中温退火,器件的电学性能有所改善.     

AlGaN/GaN SBD的正向导通特性研究

主要研究了横向AlGaN/GaN异质结肖特基势垒二极管(简称SBD)的正向导通特性,设计制备了基于蓝宝石衬底和硅衬底的不同器件结构的AlGaN/GaN SBD器件。测量结果表明,通过适当改变肖特基-欧姆电极布局,以及在导电衬底上施加相应的偏压,可以有效改善器件的正向导通特性。实验所制备的肖特基电极半径为120μm、肖特基-欧姆电极间距为25μm的基于Al2O3衬底的AlGaN/GaN SBD器件,实现了正向导通电流0.05A@2V(Ron=9.13mΩ·cm2)、反向饱和漏电流为10-6 A的性能。对制备的硅基AlGaN/GaN SBD器件的测试发现,通过外加衬底偏压能够有效改善其正向导通特性。     

AlGaN/GaN型气敏传感器对于CO的响应研究

研究了基于AlGaN/GaN型结构的气敏传感器对于C0的传感性.制备出AlGaN/GaN型气敏传感器器件,并测试得到了器件在50℃时对于不同浓度(1%,9000,8000,5000和1000ppm)的C0的响应情况;测试并分析了1%CO在50和100℃下响应度的差异,计算了通人1%CO前后器件的肖特基势垒高度的变化和灵敏度随电压的分布关系.结果表明,器件的灵敏度强烈依赖于器件的工作温度和通入的气体浓度,随着温度和浓度的增加,器件的灵敏度呈单调增加,器件在100℃空气气氛中表现出了良好恢复性能.     

AlGaN/GaN型气敏传感器对于CO的响应研究

研究了基于AlGaN/GaN型结构的气敏传感器对于CO的传感性.制备出AlGaN/GaN型气敏传感器器件,并测试得到了器件在50℃时对于不同浓度（1%,9000,8000,5000和1000ppm）的CO的响应情况;测试并分析了1%CO在50和100℃下响应度的差异,计算了通入1%CO前后器件的肖特基势垒高度的变化和灵敏度随电压的分布关系.结果表明,器件的灵敏度强烈依赖于器件的工作温度和通入的气体浓度,随着温度和浓度的增加,器件的灵敏度呈单调增加,器件在100℃空气气氛中表现出了良好恢复性能.     

AlGaN/GaN型气敏传感器对于C0的响应研究

研究了基于AlGaN/GaN型结构的气敏传感器对于C0的传感性.制备出AlGaN/GaN型气敏传感器器件,并测试得到了器件在50℃时对于不同浓度(1%,9000,8000,5000和1000ppm)的C0的响应情况;测试并分析了1%CO在50和100℃下响应度的差异,计算了通人1%CO前后器件的肖特基势垒高度的变化和灵敏度随电压的分布关系.结果表明,器件的灵敏度强烈依赖于器件的工作温度和通入的气体浓度,随着温度和浓度的增加,器件的灵敏度呈单调增加,器件在100℃空气气氛中表现出了良好恢复性能.     

AlGaN/GaN HEMT器件的研制

介绍了AlGaN/GaN HEMT器件的研制及室温下器件特性的测试.漏源欧姆接触采用Ti/Al/Pt/Au,肖特基结金属为Pt/Au.器件栅长为1μm,获得的最大跨导为120mS/mm,最大的漏源饱和电流密度为0.95A/mm.     

一种阳极连接P型埋层的AlGaN/GaN肖特基二极管

在传统AlGaN/GaN肖特基二极管中,阳极漏电始终是制约器件耐压提高的一个重要因素。因此文中研究了在缓冲层中生长P型埋层并与阳极相连的AlGaN/GaN肖特基二极管结构 AC-PBL FPs SBD来抑制阳极的泄漏电流。同时,在二极管的两级均加上场板来调制该器件的表面电场分布。经过仿真验证可知,该结构的阳极关断泄漏电流得到了有效抑制,同时辅助耗尽沟道内的2DEG,扩大空间电荷区,进而提高了器件的耐压特性。该结构的击穿电压为733 V,与传统GET SBD器件相比,击穿电压提高了近3.4倍,Baliga优值提升了近11.6倍,说明该器件可以应用在电力电子线路中。     

AlGaN/GaN横向肖特基势垒二极管的仿真与制作

基于GaN横向肖特基势垒二极管(SBD)的频率特性和应用的需要,设计了一种基于AlGaN/GaN异质结的横向SBD.利用Silvaco Atlas软件研究了 AlGaN势垒层的厚度和Al摩尔组分对异质结AlχGaN1-χ/GaN SBD电学性能的影响.仿真结果表明,SBD器件截止频率随Al摩尔组分的增加先增大再减小,当AlχGaN,1-χ层中Al摩尔组分为0.2～0.25,其厚度为20～30nm时,AlGaN/GaN SBD器件的频率特性最好.在仿真的基础上,设计制作出了肖特基接触直径为2 μm的非凹槽和凹槽型AlGaN/GaN横向空气桥SBD.通过直流I-V[测试和射频S参数测试,提取了两种SBD器件的理想因子、串联电阻、结电容、截止频率和品质因子等关键参数,该平面 SBD可应用于片上集成和混合集成的太赫兹电路的设计与制造.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.