Efficient double-clad thulium-doped fiber laser with a ring cavity

We have constructed a novel ring cavity for a double-clad thulium-doped fiber laser, by placing the fiber's 45 degrees angle-polished output end before the input end and relaunching the pump and the laser power into the fiber. This design can reduce reabsorption by using short fibers without loss of pump efficiency. The dependence of the laser's performance on the fiber's length and the output coupler's reflectivity is investigated experimentally and theoretically. With an 80-cm-long fiber, 2.7-W single-mode continuous-wave output is generated for 11.5 W of launched pump power.     

多波长掺镱光纤激光器实验研究

为了产生室温下掺镱光纤激光器稳定的多波长激光振荡,采用两个光纤环镜作为线形腔掺镱光纤激光器的端镜,在其中一个环镜中熔接一段保偏光纤构成梳状滤波器,通过优化掺镱光纤长度和腔损耗,实现了室温下1060nm附近稳定的多波长振荡.实验结果表明,在室温下,掺镱光纤存在比较明显的非均匀加宽效应,从而使得激光器的振荡波长数随泵浦功率的增加而增加.     

Modeling and optimization of Q-switched double-clad fiber lasers

The numerical modeling of actively Q-switched fiber lasers is systematically presented. On the basis of typical Q-switched ytterbium-doped double-clad fiber lasers under forward and backward pump, the dynamic characteristics of pulse energy, pulse width, population inversion, and stored energy at tens-of-kilohertz repetition rates are studied by using the traveling-wave method. The laser performance is further investigated for different fiber core diameters, doping rates, cavity lengths, fiber losses, signal and pump wavelengths, reflectivities of output coupler, and switching speed of an acousto-optic modulator; the laser optimization is also quantitatively discussed. Some simulation results are also compared with previous experimental results.     

S-band multiwavelength ring Brillouin/Raman fiber laser with 20 GHz channel spacing

We propose and demonstrate a tunable S-band multiwavelength Brillouin/Raman fiber laser (MBRFL) with a tuning range of between 1490 to 1530 nm. The proposed MBRFL is designed around a 7.7 km long dispersion compensating fiber in a simple ring configuration, acting as a nonlinear medium for the generation of multiple wavelengths from stimulated Brillouin scattering (SBS) and also as a nonlinear gain medium for stimulated Raman scattering (SRS) amplification. A laser source with a maximum power of 12 dBm acts as the Brillouin pump (BP), while two 1420 nm laser diodes with a total power of 26 dBm act as the Raman pumps (RPs). The MBRFL can generate a multiwavelength comb consisting of even and odd Stokes at an average power of -12 dBm and -14 dBm respectively, and by separating the even and odd Stokes outputs, a 20 GHz channel spacing is obtained between two consecutive wavelengths. Due to the four-wave mixing (FWM) effect, anti-Stokes lines are also observed. The multiwavelength comb generated is not dependent on the BP, thus providing high stability and repeatability and making it a highly potential source for many real-world applications. This is the first time, to the knowledge of the authors, that a tunable MBRFL has been developed using SRS to obtain gain in the S-band region.     

双包层光纤激光器泵浦阈值的解析表达式

对连续运行时双包层光纤激光器阈值的优化问题进行了分析。从速率方程组出发,在不忽略光纤损耗系数和保留再发射项主导部分的近似条件下推导出了双包层光纤激光器阈值泵浦功率的显函数解析表达式,得到了光纤激光器产生振荡所需的最小光纤长度的显函数解析解;还给出了泵浦光子数密度和上能级粒子数密度沿光纤方向随光纤长度变化的显函数解析解。最后和其他文献中在忽略泵光再发射项和激光损耗的近似条件下得到的结果进行了比较和分析。     

Multiwavelength picosecond and single wavelength femtosecond pulses emission in a passively mode-locked fiber laser using a semiconductor saturable absorber mirror and a contrast ratio tunable comb filter

We propose and demonstrate a highly flexible fiber laser capable of generating stable multiwavelength picosecond and single wavelength femtosecond pulses by using a semiconductor saturable absorber mirror and a contrast ratio tunable comb filter. In the multiwavelength lasing regime, up to 11-wavelength stable mode-locked pulses in 3 dB bandwidth with a channel spacing of 0.8 nm were obtained. While in the single wavelength with broadband spectrum lasing regime, the fiber laser emitted 576 fs soliton pulse. Through changing the contrast ratio of the comb filter, the conversion between the multiwavelength picosecond and single wavelength femtosecond pulsed operations could be efficiently achieved.     

Characterization of a multiwavelength Brillouin-erbium fiber laser based on a linear cavity configuration

We experimentally demonstrate a simple method for generating a multiwavelength Brillouin comb by utilizing a linear cavity of hybrid Brillouin-erbium fiber lasers (BEFLs). The optimization of Brillouin pump wavelength, power, and erbium gain played a significant role in determining the maximum number of Brillouin Stokes signals generated. Simultaneous and stable multiple-wavelength laser output of 22 lines with 10.88-GHz channel spacing has been obtained with good flatness. Various parameters such as 980-nm pump power, Brillouin pump wavelength, and Brillouin pump power that affect the performance of a multiwavelength BEFL system have been investigated. An analysis of the tuning range of the system is presented.     

Tunable multiwavelength fiber laser based on a double Sagnac HiBi fiber loop

A tunable multiwavelength fiber laser based on double Sagnac loops is proposed and demonstrated. Comb filter characteristics of single and double Sagnac loops are analyzed by Jones matrix. Simulated results show that there are better tunability and controllability with double loops than with a single loop, and this also has been confirmed by experimental results. By adjusting the polarization controller and the length of the polarization maintaining fiber the wavelength range, wavelength spacing, and laser linewidth can be tuned. Experimental results indicate that the linewidth of the multiwavelength fiber laser was 0.0187 nm and the optical sidemode suppression ratio was 50 dB.     

Design of a device for pumping a double-clad fiber laser with a laser-diode bar

Pumping rare-earth-doped double-clad fiber lasers with GaAlAs laser-diode bars typically requires one to transform a 1-cm-long one-dimensional linear array of tens of multimode laser-diode sources into atwo-dimensional oblong cross section that approximately matches the fiber's first cladding shape. I describe the design of a device, henceforth called a high-brightness geometric transformer, that uses a cylindrical microlens to image the laser-diode bar near field onto a linear array of soft-glass, thin-clad, rectangular fibers. In turn, the fibers output ends are arranged to form a stack that matches the required first cladding shape. For a typical laser-diode bar with a brightness of 25 mW·μm(-2)·sr(-1), the geometric transformer output brightness is 0.6 mW·μm(-2)·sr(-1), i.e., there is a 40× intermediate loss of brightness. If the output of the geometric transformer is used to pump a Nd-doped double-clad fiber laser, anoverall brightness gain of 340× can be achieved.     

Sequence lasing in a gain-switched Yb3+,Er(3+)-doped silica double-clad fiber laser

Experimental results relating to the gain-switched operation of a double-clad Yb3+,Er(3+)-doped silica fiber laser that is pulse pumped with the output from a flash-lamp-pumped Ti:sapphire laser are presented. For all the configurations of the fiber laser that we studied, the 2F5/2-->2F7/2 laser transition of the Yb3+ ion lased prior to laser emission from the 4I13/2-->4I15/2 transition of the Er3+ ion. To the best of our knowledge, this is the first reported operation of sequence lasing in the Yb3+,Er(3+)-codoped system. This succession of laser pulses deduced from the measurements of this investigation is a consequence of both the short intense pump pulse and the short 900-nm wavelength of the pump that does not overlap with any important excited-state absorption transitions. We believe that the predominant interionic interaction during the course of the pump pulse is the double-energy transfer to the Er3+ ion acting twice from the 2F5/2 energy level of the Yb3+ donor ion. A maximum total output of 1.65 mJ is obtained (1.38 mJ from the 2F5/2-->2F7/2 transition of Yb3+ and 0.27 mJ from the 4I13/2-->4I15/2 transition of Er3+) from a nonoptimized configuration of the fiber laser. The wavelength of the output from the fiber laser was measured to vary approximately linearly with fiber length from 1040 to 1046 nm for the Yb(3+)-based laser and 1535 to 1541 nm for the Er(3+)-based laser.     

Wavelength tuning in optically mode-locked semiconductor fiber ring lasers with linearly chirped fiber Bragg gratings

We demonstrate wavelength tuning in single-wavelength and multiwavelength semiconductor fiber ring lasers that are mode locked with an optically injected control signal. A semiconductor optical amplifier is used to provide gain as well as to function as an optically controlled mode-locking element. Linearly chirped fiber Bragg gratings--single or superimposed--are used to define the lasing wavelengths as well as to provide wavelength tunability and allow for multiwavelength operation. We obtain pulses of tens of picoseconds in duration when we inject a sinusoidal optical control signal into the laser cavity, and we can tune the lasing wavelength(s) over the reflection bandwidth(s) of the grating(s) by simply changing the frequency of the injected control signal.     

Wavelength switchable L-band erbium-doped fiber laser employing C-band EDFA as gain medium

A new structure for the L-band multiwavelength switchable erbium-doped fiber laser is proposed. Overlapping laser cavities are formed by cascading fiber Bragg gratings as reflectors in a ring structure with a C-band EDFA as a common gain medium. The proposed laser is made to be wavelength-switchable by individually adjusting the loss of each overlapping cavity. Instead of using an L-band EDFA as the gain medium in the L-band fiber laser, we have experimentally demonstrated that by tailoring the gain of the C-band EDFA to have a significant gain tilt in the L-band, a lasing power efficiency of 26% can be achieved over a wide range of switchable lasing wavelengths. Following this optimal design, the side-mode suppression ratio and the minimal separation between two switchable lasing wavelengths were found to be over 42 dB and 0.33 nm, respectively.     

Absorption-line-locked fiber laser for gas-sensing applications

An absorption-line-locked fiber laser based on the selection and conversion of a gas absorption line into a highly stable intracavity transmission narrowband filter is demonstrated. The laser has attractive properties for gas-sensing applications due to its frequency stability and multiwavelength selection capability.     

Switchable and tunable multiple-channel erbium-doped fiber laser using graphene-polymer nanocomposite and asymmetric two-stage fiber Sagnac loop filter

A high-performance multiple-channel erbium-doped fiber laser (EDFL) is proposed and experimentally demonstrated, using graphene-polymer nanocomposite as a multiwavelength equalizer and an asymmetric two-stage polarization-maintaining fiber (PMF) Sagnac loop as a flexible comb filter. At first, the filtering characteristics of the PMF Sagnac loop filter (SLF) are investigated. Both theoretical and experimental results show that it can provide a flexibly switchable and tunable comblike filtering. Then, the two-stage PMF SLF is inserted into a graphene-assisted EDFL cavity for generating multiwavelength oscillation. The extreme-high third-order optical nonlinearity of graphene is exploited to suppress the mode competition of the EDFL, and a stable multiple-channel lasing is observed. By carefully adjusting the polarization controllers in the two-stage PMF SLF, not only can the lasing-line number per channel be switchable between single and multiple wavelengths, but also the wavelength spacing in the triple-wavelength condition can be tunable. In the case of triple wavelengths per channel, up to 12 wavelengths with four channels stable oscillations can be achieved. The multiple-channel EDFL can keep a high extinction ratio of >40 dB and a narrow linewidth of <0.01 nm.     

Modeling and optimization of add-drop dynamics in gain-clamped fiber amplifiers

A new dynamic model for gain-clamped fiber amplifiers is presented. The model can simulate the transient behavior of a gain-clamped erbium-doped fiber amplifier as a function of its controlling parameters. Results show the detailed dependence of the amplifier gain dynamics on launched pump power and reveal the pump-power penalty incurred in implementing gain control with minimal transients to power disturbances. The effect on the transients of varying the laser cavity feedback coupling is also presented. Model accuracy is verified by the excellent quantitative agreement with dynamic measurements over a range of operating conditions. Results show how an increase in pump power can effectively suppress both the dynamic and the steady-state signal power transients in wavelength-division multiplexing channel add-drop operations.     

Passively Q-switched Tm(3+)-doped silica fiber lasers

By splicing on a length of Ho(3+)-doped silica fiber onto a diode-pumped double-clad Tm(3+)-doped silica fiber, stable passive Q switching of the Tm(3+)-doped silica fiber laser is demonstrated. The formation of Q-switched pulses was found to depend on both the length and the position of the Ho(3+)-doped silica fiber that was inserted into the fiber laser cavity. For stable Q-switched pulse generation, Ho(3+)-doped silica fiber lengths shorter than twice the absorption depth must be used. For long Ho(3+)-doped silica fiber lengths, randomly generated pulses are observed at operating wavelengths longer than 2090 nm, which are attributed to intracavity pumping of the Ho(3+)-doped silica fiber.     

Narrow-linewidth, multi-Watt Yb-doped fiber amplifier at 1014.8 nm

We report on an efficient, narrow linewidth, two-stage fiber amplifier at 1014.8 nm based on Yb-doped double-clad fibers. The fibers are cooled to liquid-nitrogen temperatures in order to suppress absorption at the operating wavelength. We achieved output powers of up to 5.0 W at a linewidth of less than 3 MHz by seeding the amplifier with the radiation from an external cavity diode laser.     

Multifrequency erbium-doped fiber laser operating at room temperature

A method to realize room-temperature operation of a multifrequency Er-doped fiber laser with low-frequency shift feedback placed within a linear laser cavity is theoretically proposed and experimentally demonstrated. Simultaneous multiwavelength lasing with 0.5 nm wavelength spacing is experimentally demonstrated by applying a sinusoidal signal of 10 kHz to a fiber phase modulator inserted within the linear cavity to prevent single wavelength steady-state oscillation. In the linear cavity, an all-polarization-maintaining fiber Sagnac loop is used as a periodic filter, and a single-mode fiber loop with a polarization controller is used as a partial reflector and also as an output port.     

光纤饱和吸收体稳频窄线宽光纤激光器

结合光纤饱和吸收体与光纤光栅法布里-珀罗标准具,研制出了全光纤结构1550nm单频窄线宽掺铒光纤环形激光器.采用两个976nm激光二极管双向抽运作为抽运源,高掺杂浓度铒光纤作为增益介质,以行波腔消除空间烧孔效应,利用光纤光栅法布里-珀罗标准具窄带选模特性,以10m长低掺铒光纤饱和吸收体稳频,得到了十分稳定的窄线宽激光输出.激光器抽运阈值功率21mW,在抽运光功率为145mW时输出光功率39mW,斜率效率30%,信噪比大于50dB.采用延迟自外差方法精确测量光纤激光器线宽小于10kHz.