Influenceof the Laminar Plasma Torch Construction on the Jet Characteristics

Based on two typical laminar plasma torches(LPT), i.e. a multi-electrode plasma torch(MEPT) with segmented anode structure and a two-electrode plasma torch(TEPT) with conventional structure, this paper studied the influence of the LPTs construction on the jet characteristics. Experiments were designed to measure their arc voltage, jet length, thermal efficiency and specific enthalpy using a home-made data acquisition system. With them, the jet characteristics of the two different LPTs were compared in detail. Results show that different plasma torch construction leads to distinctively different characteristics of the generated plasma jet. Based on the different jet characteristics, a plasma torch with appropriate construction could be used to meet the different application requirements.     

Study on an Atmospheric Pressure Plasma Jet and its Application in Etching Photo-Resistant Materials

An atmospheric pressure radio-frequency plasma jet that can eject cold plasma has been developed. In this paper, the configuration of this type of plasma jet is illustrated and its discharge characteristics curves are studied with a current and a voltage probe. A thermal couple is used to measure the temperature distribution along the axis of the jet stream. The temperature distribution curve is generated for the He/O2 jet stream at the discharge power of 150 W. This jet can etch the photo-resistant material at an average rate of 100 nm/min on the surface of silicon wafers at a right angle.     

Experimental Characterization of the Plasma Synthetic Jet Actuator

The plasma synthetic jet is a novel active flow control method because of advantages such as fast response,high frequency and non-moving parts,and it has received more attention recently,especially regarding its application to high-speed flow control.In this paper,the experimental characterization of the plasma synthetic jet actuator is investigated.The actuator consists of a copper anode,a tungsten cathode and a ceramic shell,and with these three parts a cavity can be formed inside the actuator.A pulsed-DC power supply was adopted to generate the arc plasma between the electrodes,through which the gas inside was heated and expanded from the orifice.Discharge parameters such as voltage and current were recorded,respectively,by voltage and current probes.The schlieren system was used for flow visualization,and jet velocities with different discharge parameters were measured.The schlieren images showed that the strength of plasma jets in a series of pulses varies from each other.Through velocity measurement,it is found that at a fixed frequency,the jet velocity hardly increases when the discharge voltage ranges from 16 kV to 20 kV.However,with the discharge voltage fixed,the jet velocity suddenly decreases when the pulse frequency rises above 500 Hz,whereas at other testing frequencies no such decrease was observed.The maximum jet velocity measured in the experiment was up to110 m/s,which is believed to be effective for high-speed flow control.     

Nonequilibrium Atmospheric Pressure Ar/O2 Plasma Jet: Properties and Application to Surface Cleaning

In this study an atmospheric pressure Ar/O_2 plasma jet is generated to study the effects of applied voltage and gas flux rate to the behavior of discharge and the metal surface cleaning.The increase in applied voltage leads to increases of the root mean square(rms) current,the input power and the gas temperature.Furthermore,the optical emission spectra show that the emission intensities of metastable argon and atomic oxygen increase with increasing applied voltage.However,the increase in gas flux rate leads to a reduction of the rms current,the input power and the gas temperature.Furthermore,the emission intensities of metastable argon and atomic oxygen decrease when gas flux rate increases.Contact angles are measured to estimate the cleaning performance,and the results show that the increase of applied voltage can improve the cleaning performance.Nevertheless,the increase of gas flux rate cannot improve the cleaning performance.Contact angles are compared for different input powers and gas flux rates to search for a better understanding of the major mechanism for surface cleaning by plasma jets.     

Mechanisms of Streamer Propagation Affected by Driven Voltage Polarity in a Cold Atmospheric Pressure Plasma Jet

A two-dimensional self-consistent fluid model is used to investigate the effects of DC-voltage polarity in plasma initiation and propagation of helium plasma jet.The simulation results indicate that the difference in initial breakdown for the positive jet and negative jet leads to a difference in the electron density of about 4 orders of magnitude,even with the same initial electric field,which also influences the subsequent propagation.In the propagation process of negative jets,the ionization process exists in a longer gas channel behind the streamer head.In addition,the drift process to the infinite grounded electrode driven by the electric field results in higher energy consumption in the ionization process.However,in the positive jet,the ionization process mainly exists in the streamer head.Therefore,the differences in the initial breakdown and propagation process make the electric field intensity and the ionization weaker in the streamer head of the negative jet,which explains the weaker and shorter appearance of the negative jet compared to the positive jet.Our model can adequately reproduce the experimental results,viz.a bullet-like propagation in the positive jet and a continuous plasma plume in the negative jet.Furthermore,it also indicates that the streamer velocity shows the same variations as the electron drift velocity for both positive and negative jets.     

Sterilization of Staphylococcus Aureus by an Atmospheric Non-Thermal Plasma Jet

An atmospheric non-thermal plasma jet was developed for sterilizing the Staphylococcus aureus (S. aureus). The plasma jet was generated by dielectric barrier discharge (DBD), which was characterized by electrical and optical diagnostics. The survival curves of the bacteria showed that the plasma jet could effectively inactivate 10 6 cells of S. aureus within 120 seconds and the sterilizing efficiency depended critically on the discharge parameter of the applied voltage. It was further confirmed by scanning electron microscopy (SEM) that the cell morphology was seriously damaged by the plasma treatment. The plasma sterilization mechanism of S. aureus was attributed to the active species of OH, N 2 + and O, which were generated abundantly in the plasma jet and characterized by OES. Our findings suggest a convenient and low-cost way for sterilization and inactivation of bacteria.     

A Brief Study on the Ignition of the Non-Thermal Atmospheric Pressure Plasma Jet from a Double Dielectric Barrier Configured Plasma Pencil

To understand the self sustained propagation of the plasma jet/bullet in air under atmospheric pressure, the ignition of the plasma jet/bullet, the plasma jet/bullet ignition point in the plasma pencil, the formation time and the formation criteria from a dielectric barrier configured plasma pencil were investigated in this study. The results were confirmed by comparing these results with the plasma jet ignition process in the plasma pencil without a dielectric barrier. Electrical, optical, and imaging techniques were used to study the formation of the plasma jet from the ignition of discharge in a double dielectric barrier configured plasma pencil. The investigation results show that the plasma jet forms at the outlet of the plasma pencil as a donut shaped discharge front because of the electric field line along the outlet’s surface. It is shown that the required time for the formation of the plasma jet changes with the input voltage of the discharge. The input power calculation for the gap discharge and for the whole system shows that 56% of the average input power is used by the first gap discharge. The estimated electron density inside the gap discharge is in the order of 1011cm-3 . If helium is used as a feeding gas, a minimum 1.48×10-8C charge is required per pulse in the gap discharge to generate a plasma jet.     

Observation of the Emission Spectra of an Atmospheric Pressure Radio-frequency Plasma Jet

An atmospheric pressure plasma jet （APPJ） using radio-frequency （13.56 MHz） power has been developed to produce homogeneous glow discharge at low temperature. With optical emission spectroscopy, we observed the excited species （atomic helium, atomic oxygen and metastable oxygen） generated in this APPJ and their dependence on gas composition ratio and RF power. O and O2（b1∑g^＋） are found in the effluent outside the jet by measuring the emission spectra of effluent perpendicular to the jet. An interesting phenomenon is found that there is an abnormal increase of O emission intensity （777.4 nm） between 10 mm and 40 mm away from the nozzle. This observation result is very helpful in practical operation.     

直流电弧等离子体点火器射流特性研究

采用光谱仪测量了等离子体点火器出口射流的发射光谱,利用玻尔兹曼曲线斜率法计算了射流的电子温度,并通过电离平衡方程计算了射流气体温度,获得点火器出口射流长度、射流速度、电子温度和射流温度随弧电流及进口氩气流量的变化规律。并分析了航空等离子体电弧射流中是否可使用电子温度来代替射流气体温度。实验表明：弧电流随着进口氩气流量的增大而减小;出口射流长度和速度随弧电流的增大而增大,随进口氩气流量的增大先增大后减小;出口电子温度、电子密度和射流温度随弧电流的增大而升高,随氩气流量的增大而降低。     

Effects of Gas Flow Rate on the Discharge Characteristics of a DC Excited Plasma Jet

A direct current(DC) source excited plasma jet consisting of a hollow needle anode and a plate cathode has been developed to form a diffuse discharge plume in ambient air with flowing argon as the working gas.Using optical and electrical methods,the discharge characteristics are investigated for the diffuse plasma plume.Results indicate that the discharge has a pulse characteristic,under the excitation of a DC voltage.The discharge pulse corresponds to the propagation process of a plasma bullet travelling from the anode to the cathode.It is found that,with an increment of the gas flow rate,both the discharge plume length and the current peak value of the pulsed discharge decrease in the laminar flow mode,reach their minima at about1.5 L/min,and then slightly increase in the turbulent mode.However,the frequency of the pulsed discharge increases in the laminar mode with increasing the argon flow rate until the argon flow rate equals to about 1.5 L/min,and then slightly decreases in the turbulent mode.     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

Numerical study of the effect of coflow argon jet on a laminar argon thermal plasma jet

The effects of the velocity and width in coflow argon jet inlet on the flow characteristics of laminar argon thermal plasma jet flowing into the cold air have been studied by the large eddy simulation methods. The Kelvin–Helmholtz instability between argon thermal plasma jet and coflow argon jet causes the transition from a laminar jet to a turbulent jet in the presence of coflow argon jet. Moreover, increasing the velocity and width in coflow argon jet inlet can enhance turbulent transport and provoke coherent structure in the downstream of thermal plasma jet. And the mixing characteristics between argon thermal plasma, coflow argon and ambient air are strengthened. In addition, the width in coflow argon jet inlet has a significant effect on the distribution of temperature in the upstream of thermal plasma jet. It was also found that the transition occurs in advance with the increase of velocity and width in coflow argon jet inlet.     

Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit.We characterized the arc plasma jet flow appearance at different currents by using high-speed photography,and two polished contacts were used to search for the relationship between roughness and plasma jet flow.Then,to make the nature of arc plasma jet flow phenomena clear,a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated.The simulated DC arc plasma was presented with the temperature distribution and the current density distribution.Furthermore,the calculated arc flow vclocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress.The combined action of volume force and contact surface was the main reason of the arc jet flow.     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.     

Treatment of Bone Waste Using Thermal Plasma Technology

Daily meat consumption produces a lot of bone waste, and dumped bone waste without treatment would result in environmental hazards. Conventional treatment methods of waste bones have some disadvantages. Herein, an investigation of bone waste treated using thermal plasma technology is presented. A high-temperature plasma torch operated at 25.2 kW was used to treat bone waste for seven minutes. The bone waste was finally changed into vitric matter and lost 2/3 of its weight after the treatment. The process was highly efficient, economical, convenient, and fuel-free. This method could be used as an alternative for disposal of bone waste, small infectious animals, hazardous hospital waste, etc.     

T型管热混合温度波动特性研究

在反应堆发生失水事故(LOCA)时,一回路系统压力降低,产生大量蒸汽,堆芯应急冷却系统(ECCS)启动后,安注水注入冷腿后在T型管处与蒸汽发生热混合,温度会出现明显波动,同时伴随有一定的回流。本文以T型管中冷热流体混合为研究对象,开展了安注过冷水与冷腿中的饱和蒸汽热混合实验。研究内容主要为过冷水与饱和蒸汽在水平T型管发生热混合之后的水跃和回流现象,基于动量分析的方法,分析了不同流型对热混合后温度分布的影响,提出了两相流动量比关系式用于分析T型管内温度波动特性。     

核动力厂温排水混合区范围的可接受性论证的初步研究

基于国内现有的温排放控制标准可执行性不强的现状,以某滨海电站SNP（采用一次直流冷却循环）厂址为例,开展了温排水混合区范围的可接受性论证研究。通过对该电站厂址海域生态调查站位的春、秋季调查结果的聚类分析,得出如下结论：1） SNP一期（1~2号机组）运行工况下,温排水混合区的设定对海域整体生态功能影响较小,其范围可接受;2） SNP一、二期（1~4号机组）同时运行工况下,温排水混合区的设定,春季对海域整体生态功能影响较小,其范围可接受,秋季对海域整体生态功能影响非常显著,如无有效的缓解措施,其影响是不可接受的。     

热处理和添加Cu对SiC-C涂层与基体混合效应的影响

在不锈钢基体上用离子束混合技术沉积SiC-C涂层,为有效提高SiC-C涂层与不锈钢基体元素的混合效应,采用涂覆后对样品进行加热处理以及在不锈钢基体上预沉积Cu薄膜的方法,试图改善SiC-C涂层与基体的混合效果。通过二次离子质谱（SIMS）测试分析涂层与基体的界面组份分布。结果表明,加热处理可以提高SiC-C涂层组元向基体的内扩散,但效果不甚显著。添加Cu层以及随后的加热处理可极大提高与不锈钢基体的混合程度。     

Preliminary Study of Thermal Treatment of Coke Wastewater Sludge Using Plasma Torch

Thermal plasma was applied for the treatment of coke wastewater sludge derived from the steel industry in order to investigate the feasibility of the safe treatment and energy recovery of the sludge. A 30 k W plasma torch system was applied to study the vitrification and gas production of coke wastewater sludge. Toxicity leaching results indicated that the sludge treated via the thermal plasma process converted into a vitrified slag which resisted the leaching of heavy metals. CO2 was utilized as working gas to study the production and heat energy of the syngas. The heating value of the gas products by thermal plasma achieved 8.43 k J/L, indicating the further utilization of the gas products. Considering the utilization of the syngas and recovery heat from the gas products, the estimated treatment cost of coke wastewater sludge via plasma torch was about 0.98 CNY/kg sludge in the experiment. By preliminary economic analysis, the dehydration cost takes an important part of the total sludge treatment cost. The treatment cost of the coke wastewater sludge with 50 wt.% moisture was calculated to be about 1.45 CNY/kg sludge dry basis. The treatment cost of the coke wastewater sludge could be effectively controlled by decreasing the water content of the sludge. These findings suggest that an economic dewatering pretreatment method could be combined to cut the total treatment cost in an actual treatment process.     

Influence of Additive Gas on Electrical and Optical Characteristics of Non-equilibrium Atmospheric Pressure Argon Plasma Jet

Electrical and optical properties of an argon plasma jet were characterized. In particular, effects of an additive gas, namely nitrogen or oxygen, on these prop...