Influence of high rates of supplemental cooled EGR on NOx and PM emissions of an automotive HSDI diesel engine using an LP EGR loop

Previous experimental studies on diesel engine have demonstrated the potential of exhaust gas recirculation (EGR) as an in‐cylinder NO_x control method. Although an increase in EGR at constant boost pressure (substitution EGR) is accompanied with an increase in particulate matter (PM) emissions in the conventional diesel high‐temperature combustion (HTC), the recirculation of exhaust gases supplementary to air inlet gas (supplemental EGR) by increasing the boost pressure has been suggested as a way to reduce NO_x emissions while limiting the negative impact of EGR on PM emissions. In the present work, a low‐pressure (LP) EGR loop is implemented on a standard 2.0 l automotive high‐speed direct injection (HSDI) turbocharged diesel engine to study the influence of high rates of supplemental cooled EGR on NO_x and PM emissions. Contrary to initial high‐pressure (HP) EGR loop, the gas flow through the turbine is unchanged while varying the EGR rate. Thus, by closing the variable geometry turbine (VGT) vanes, higher boost pressure can be reached, allowing the use of high rates of supplemental EGR. Furthermore, recirculated exhaust gases are cooled under 50°C and water vapour is condensed and taken off from the recirculated gases. An increase in the boost pressure at a given inlet temperature and dilution ratio (DR) results in most cases an increase in NO_x emissions and a decrease in PM emissions. The result of NO_x–PM trade‐off, while varying the EGR rate at fixed inlet temperature and boost pressure depends on the operating point: it deteriorates at low load conditions, but improves at higher loads. Further improvement can be obtained by increasing the injection pressure. A decrease by approximately 50% of NO_x emissions while maintaining PM emission level, and brake specific fuel consumption can be obtained with supplemental cooled EGR owing to an LP EGR loop, compared with the initial engine configuration (HP moderately cooled EGR). Copyright © 2008 John Wiley & Sons, Ltd.     

Investigation of the effects of hydrogen on cylinder pressure in a split-injection diesel engine at heavy EGR

The distinctive properties of hydrogen have initiated considerable applied research related to the internal combustion engine. Recently, it has been reported that NO_x emissions were reduced by using hydrogen in a diesel engine at low temperature and heavy EGR conditions. As the continuing study, cylinder pressure was also investigated to determine the combustion characteristics and their relationship to NO_x emissions. The test engine was operated at constant speed and fixed diesel fuel injection rate (1500 rpm, 2.5 kg/h). Diesel fuel was injected in a split pattern into a 2-L diesel engine. The cylinder pressure was measured for different hydrogen flow rates and EGR ratios. The intake manifold temperature was controlled to be the same to avoid the gas intake temperature variations under the widely differing levels (2%-31%) of EGR. The measured cylinder pressure was analyzed for characteristic combustion values, such as mass burn fraction and combustion duration.The rising crank angle of the heat release rate was unaffected by the presence of hydrogen. However, supplying hydrogen extended the main combustion duration. This longer main combustion duration was particularly noticeable at the heavy EGR condition. It correlated well with the reduced NO_x emissions.     

Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine

Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production and is used on most modern high-speed direct injection (HSDI) diesel engines. However EGR has different effects on combustion and emissions production that are difficult to distinguish (increase of intake temperature, delay of rate of heat release (ROHR), decrease of peak heat release, decrease in O₂ concentration (and thus of global air/fuel ratio (AFR)) and flame temperature, increase of lift-off length, etc.), and thus the influence of EGR on NO_x and particulate matter (PM) emissions is not perfectly understood, especially under high EGR rates. An experimental study has been conducted on a 2.0 l HSDI automotive diesel engine under low-load and part load conditions in order to distinguish and quantify some effects of EGR on combustion and NO_x/PM emissions. The increase of inlet temperature with EGR has contrary effects on combustion and emissions, thus sometimes giving opposite tendencies as traditionally observed, as, for example, the reduction of NO_x emissions with increased inlet temperature. For a purely diffusion combustion the ROHR is unchanged when the AFR is maintained when changing in-cylinder ambient gas properties (temperature or EGR rate). At low-load conditions, use of high EGR rates at constant boost pressure is a way to drastically reduce NO_x and PM emissions but with an increase of brake-specific fuel consumption (BSFC) and other emissions (CO and hydrocarbon), whereas EGR at constant AFR may drastically reduce NO_x emissions without important penalty on BSFC and soot emissions but is limited by the turbocharging system.     

Combining GTL fuel,reformed EGR and HC-SCR aftertreatment system to reduce diesel NOx emissions. A statistical approach

An ultra-low sulphur diesel (ULSD) fuel and a synthetic gas-to-liquid (GTL) fuel, besides different types of standard and reformed EGR, were evaluated in a single-cylinder, direct injection, diesel engine equipped with hydrocarbon-selective catalytic reduction (HC-SCR) aftertreatment system. The results obtained were statistically analysed (at 95% statistical significance) to identify the most significant factors that affect NO_x emissions and to search for the optimum operation conditions in order to minimize these emissions. For that purpose, a fully crossed factorial experimental design was used, including two different engine speeds (1200 and 1500 rpm), two engine loads (25% and 50%), and four EGR/REGR ratios (0%, 10%, 20% and 30%) resulting in almost one hundred tests. An optimal combination of fuel type, REGR type and REGR ratio was proved to reduce around 89–95% of the reference NO_x emissions. In general, at 25% engine load GTL fuelling combined with the reformed EGR with the highest hydrogen content was found the most desirable, as the hydrogen sharply increased the NO_x conversion in the SCR catalyst. Differently, at 50% load standard EGR was sufficient to reach high NO_x reductions. These findings may be used for the implementation of a system on-board capable to switch from EGR to REGR, which will help engine manufacturers to meet the future emission regulations.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Comparative analysis of H2-diesel co-combustion in a single cylinder engine and a chassis dynamometer vehicle

Concerns as to the adverse effects of diesel engine exhaust on urban air quality have resulted in increasingly stringent emissions legislation, with the prospect of many major global cities potentially banning diesel vehicles. Emissions of nitrogen oxides (NO_x) and particulate matter (PM) are linked to increases in premature mortality, and the simultaneous control of both pollutants through modified combustion strategies presents a significant challenge. In this work, the effects of displacing diesel fuel with hydrogen on exhaust emissions were investigated in both a single cylinder research engine and in a demonstration vehicle. In the initial stage, tests were undertaken on a supercharged, direct injection, single cylinder diesel research engine at different engine loads, intake air pressures and EGR levels. Hydrogen was aspirated with the intake air, and EGR was simulated by supplying the intake pipe with compressed nitrogen gas. The results showed a reduction in CO₂ and particulate emissions with increasing H₂ addition, and an increase in NO_x emissions at H₂ levels greater than 10% of the total input energy to the engine. The next stage involved tests on a chassis dynamometer with a small van equipped with the multi-cylinder version of the single cylinder research engine. The van was fitted with a programmable H₂ augmentation system, with H₂ addition levels specified by accelerator pedal position. During full drive cycle tests conducted with and without H₂ augmentation up to 10%, an average rate of 1 kW of H₂ was supplied to the engine. With H₂ augmentation, over the total drive-cycle, reductions in CO, NO_x and particle number were observed, but a higher total PM mass was recorded.     

Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation)

The effects of biodiesel (rapeseed methyl ester, RME) and different diesel/RME blends on the diesel engine NO_x emissions, smoke, fuel consumption, engine efficiency, cylinder pressure and net heat release rate are analysed and presented. The combustion of RME as pure fuel or blended with diesel in an unmodified engine results in advanced combustion, reduced ignition delay and increased heat release rate in the initial uncontrolled premixed combustion phase. The increased in-cylinder pressure and temperature lead to increased NO_x emissions while the more advanced combustion assists in the reduction of smoke compared to pure diesel combustion. The lower calorific value of RME results in increased fuel consumption but the engine thermal efficiency is not affected significantly. When similar percentages (% by volume) of exhaust gas recirculation (EGR) are used in the cases of diesel and RME, NO_x emissions are reduced to similar values, but the smoke emissions are significantly lower in the case of RME. The retardation of the injection timing in the case of pure RME and 50/50 (by volume) blend with diesel results in further reduction of NO_x at a cost of small increases of smoke and fuel consumption.     

Hydrogen-diesel fuel co-combustion strategies in light duty and heavy duty CI engines

The co-combustion of diesel fuel with H₂ presents a promising route to reduce the adverse effects of diesel engine exhaust pollutants on the environment and human health. This paper presents the results of H₂-diesel co-combustion experiments carried out on two different research facilities, a light duty and a heavy duty diesel engine. For both engines, H₂ was supplied to the engine intake manifold and aspirated with the intake air. H₂ concentrations of up to 20% vol/vol and 8% vol/vol were tested in the light duty and heavy duty engines respectively. Exhaust gas circulation (EGR) was also utilised for some of the tests to control exhaust NO_x emissions.The results showed NO_x emissions increase with increasing H₂ in the case of the light duty engine, however, in contrast, for the heavy duty engine NO_x emissions were stable/reduced slightly with H₂, attributable to lower in-cylinder gas temperatures during diffusion-controlled combustion. CO and particulate emissions were observed to reduce as the intake H₂ was increased. For the light duty, H₂ was observed to auto-ignite intermittently before diesel fuel injection had started, when the intake H₂ concentration was 20% vol/vol. A similar effect was observed in the heavy duty engine at just over 8% H₂ concentration.     

Enhancing the NO2/NOx ratio in compression ignition engines by hydrogen and reformate combustion,for improved aftertreatment performance

Enhanced NO₂ production (without raising total NOx) in a diesel engine combustion chamber can improve the performance of several catalytic aftertreatment systems. Thus this can facilitate a further reduction in key regulated emissions such as nitrogen oxides (NOx) and particulate matter (PM) emissions. The oxidation of NO to NO₂ is an important intermediate step involved in all current aftertreatment systems that are designed for NOx and PM catalytic removal. The performance of both NOx control systems and catalysed particulate filters depend highly on the NO₂ concentration. In this work we have examined the influence of using hydrogen (H₂) and simulated reformate (H₂, CO and EGR gases) as a supplement to diesel fuel on NO₂ production. In actual engine applications a reformer will be integrated within the engine EGR system. This will not only provide the engine with recirculated exhaust gas (i.e. EGR), but will enrich it with H₂ and CO.     

Generating efficiency and NOx emissions of a gas engine generator fueled with a biogas–hydrogen blend and using an exhaust gas recirculation system

This paper investigates the generating efficiency and NO_x emissions of a gas engine generator with a low-pressure loop exhaust gas recirculation system, fueled by a model biogas. Experiments for improving the generating efficiency and reducing NO_x emissions were conducted, utilizing optimum spark timings based on the maximum generating efficiencies with varying exhaust gas recirculation (EGR) rates. The test results show that both the NO_x emissions and the generating efficiency generally decrease when the EGR rate is increased. Also, by utilizing optimum spark timings with varying EGR rates, the addition of hydrogen to the biogas increases the generating efficiency of the engine. In particular, the generating efficiency of the biogas–hydrogen test increased by about 1.5% in comparison with the model biogas test for the optimum spark timing at 15% EGR. Accordingly, comprehensive techniques, such as the use of a biogas–hydrogen fuel mixture and optimum spark timings with respect to EGR rates, should be employed to efficiently generate electricity with a biogas engine.     

Development of variable timing fuel injection cam for effective abatement of diesel engine emissions

Fossil fuel run diesel engines are being favored in light, medium and heavy duty applications as they exhibit higher fuel conversion efficiencies. Direct injection diesels are still facing challenges to obtain trade-off between oxides of nitrogen and particulate emissions. There are sophisticated strategies such as common rail direct injection, particulate filters with associated sensors and actuators but limited to expensive comfort vehicles. In the present experimental study, a mechanically operated simple component, variable timing fuel injection cam, is designed for a 510 cc automotive type naturally aspirated, water-cooled, direct injection diesel engine. Modifications in the fuel injection cam and gear train are carried out to suit the existing engine configuration. Variable speed tests are carried out for testing the efficacy of component on both engine and chassis dynamometers for performance and emissions. It is observed that the engine which is already retarded could further be retarded with variable timing fuel injection cam. Significant reductions in NO_x and smoke emission levels are achieved. Combined effect of VIC with 7% EGR could reduce CO by about 88%, HC + NO_x by 37% and PM emissions by 90%. The Engine incorporated with the designed component and EGR, successfully satisfied the existing emission norms with improved power and specific fuel consumption.     

Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Hydrogen rich exhaust gas recirculation (H2EGR) for performance improvement and emissions reduction of a compression ignition engine

Hydrogen (H₂), being carbon free energy carrier, is best suitable for compression ignition (CI) engines with better performance and lower carbon derived emissions. Novelty of present study is the employment of low-cost catalyst (alumina) for production of H₂ reformate (hydrogen rich exhaust gas recirculation: H2EGR) in an indigenous catalytic reactor. Experimental tests were carried out on a CI engine under three conditions; base diesel, exhaust gas recirculation (EGR), and H2EGR. Results indicated that brake thermal efficiency of the engine with H2EGR was higher than EGR and comparable with base diesel operation. All carbon-based emissions including smoke emission decreased significantly with H2EGR than diesel and EGR operations. In addition, oxides of nitrogen emission (NO_x) also decreased by about 46% with H2EGR than base diesel operation. It is concluded that H2EGR is a promising option for CI engines for simultaneous reduction of both NO_x and smoke emissions along with the additional benefit of higher efficiency.     

The influence of hydrogen-enriched gas on the performance of lean NOx trap catalyst for a light-duty diesel engine

Modern diesel engines have improved engine fuel economy and significantly reduced nitrogen oxides (NO_x) and particulate matter (PM) emissions achieved by advances in both combustion and exhaust aftertreatment technologies. Recently, it has been shown that the vehicle emissions can be further improved by several catalytic systems including fuel reformers and aftertreatment systems, such as the Lean NO_x Trap (LNT). This NO_x removal system, called LNT, absorbs NO_x under lean exhaust gas conditions and releases NO_x under rich conditions. This technology can provide high NO_x conversion efficiency, but the right amount of reducing agent should be supplied into the catalytic converter under appropriate conditions.     

Comparison of the effects of EGR and lean burn on an SI engine fueled by hydrogen-enriched low calorific gas

A naturally aspirated spark ignition (SI) engine fueled by hydrogen-blended low calorific gas (LCG) was tested in both exhaust gas recirculation (EGR) and lean burn modes. The “dilution ratio” was introduced to compare their effects on engine performance and emissions under identical levels of dilution. LCG composed of 40% natural gas and 60% nitrogen was used as a main fuel, and hydrogen was blended with the LCG in volumes ranging from 0 to 20%. The engine test results demonstrated that EGR operations at stoichiometry showed a narrower dilution range, inferior combustion characteristics, lower brake thermal efficiency, faster nitrogen oxides (NO_x) suppression, and higher total hydrocarbon (THC) emissions for all hydrogen blending rates compared to lean burn. These trends were mainly due to the increased oxygen deficiency as a result of using EGR in LCG/air mixtures. Hydrogen enrichment of the LCG improved combustion stability and reduced THC emissions while increasing NO_x. In terms of efficiency, hydrogen addition induced a competition between combustion enhancement and increases in the cooling loss, so that the peak thermal efficiency occurred at 10% H₂ with excess air ratio of 1.5. The engine test results also indicated that a close-to-linear NO_x-efficiency relationship occurred for all hydrogen blending rates in both operations as long as stable combustion was achieved. NO_x versus combustion duration analysis showed that adding H₂ reduced combustion duration while maintaining the same level of NO_x. The methane fraction contained in the THC emissions decreased slightly with an increase in hydrogen enrichment at low EGR or excess air dilution ratios, but this tendency was diminished at higher dilution ratios because of the combined dilution effects from the inert gas in the LCG and the diluents (EGR or excess air).     

Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were carried out in three sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME at various speeds under full load are determined and compared. Secondly, tests were performed at constant speed with two loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Thirdly, the effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light-duty diesel engines. With the application of the EGR method, the CO and HC concentration in the engine-out emissions increased. For all operating conditions, a better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5–15% with very little economy penalty.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Analysis of reformed EGR on the performance of a diesel particulate filter

The use of a diesel particulate filter (DPF) in combination with an upstream diesel oxidation catalyst (DOC) has been successfully implemented and shown to reduce carbon monoxide (CO), hydrocarbon (HC) and Particulate Matter (PM) diesel exhaust gas emissions. However issues including cost, size and uncontrolled active regeneration under a low temperature window still require attention. This study therefore primarily focuses on the potential benefits of using a single catalytic coated DPF (cDPF) and a combined DOC-cDPF instead of the DOC-DPF aftertreatment system utilising a passive, low temperature regeneration method. Comparisons were made through monitoring exhaust gas compositions from an experimental single cylinder diesel engine as well as measuring the pressure drop across the filters to analyse the accumulation of soot particles. The influence of reformed EGR (REGR), enriched simulated hydrogen (H₂) and CO, on DPF and cDPF soot loading was of interest as H₂ promotes the NO to NO₂ oxidation. Similarly the addition of simulated reformate (added either directly into the engine intake or exhaust manifold) for optimal performance of the aftertreatment systems was examined.The effects of adding REGR resulted in a significant decrease in total engine-out NO_x emissions, as well as an increase in both NO₂ concentration and NO₂/NO_x ratio. This resulted in improved filter efficiency and overall loading, especially under a DOC-cDPF aftertreatment configuration system. As a whole, a simultaneous NO_x and PM reduction was achieved.     

Remarkable improvement of NOx–PM trade-off in a diesel engine by means of bioethanol and EGR

In order to realize a premixed compression ignition (PCI) engine, the effects of bioethanol–gas oil blends and exhaust gas recirculation (EGR) on PM–NO_x trade-off have been investigated focusing on ignition delay, premixed combustion, diffusion combustion, smoke, NO_x and thermal efficiency. The present experiment was done by increasing the ethanol blend ratio and ethanol and by increasing the EGR ratio in a single cylinder direct injection diesel engine. It is found that a remarkable improvement in PM–NO_x trade-off can be achieved by promoting the premixing based on the ethanol blend fuel having low evaporation temperature, large latent heat and low cetane number as well, in addition, based on a marked elongation of ignition delay due to the low cetane number fuel and the low oxygen intake charge. As a result, very low levels of NO_x and PM, which satisfies the 2009 emission standards imposed on heavy duty diesel engines in Japan, were achieved without deterioration of brake thermal efficiency in the PCI engine fuelled with the 50% ethanol blend diesel fuel and the high EGR ratio. It is noticed that smoke can be reduced even by increasing the EGR ratio under the highly premixed condition.