Preparation and characterization of sulfonated amine-poly(ether sulfone)s for proton exchange membrane fuel cell

Sulfonated amine-poly(ether sulfone)s (S-APES)s were prepared by nitration, reduction and sulfonation of poly(ether sulfone) (ultrason^®-S6010). Poly(ether sulfone) was reacted with ammonium nitrate and trifluoroacetic anhydride to produce the nitrated poly(ether sulfone), and was followed by reduction using tin(II)chloride and sodium iodide as reducing agents to give the amino-poly(ether sulfone). The S-APES was obtained by reaction of 1,3-propanesultone and the amino-poly(ether sulfone) (NH₂-PES) with sodium methoxide. The different degrees of nitration and reduction of poly(ether sulfone) were successfully synthesized by an optimized process. The reduction of nitro group to amino was done quantitatively, and this controlled the contents of the sulfonic acid group. The films were converted from salt to acid forms with dilute hydrochloric acid. Different contents of sulfonated unit of the S-APES were studied by FT-IR, ¹H NMR spectroscopy, differential scanning calorimetry (DSC), and thermo gravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. The ion exchange capacity (IEC), a measure of proton conductivity, was evaluated. The S-APES membranes exhibit conductivities (25 °C) from 1.05 × 10⁻³ to 4.83 × 10⁻³ S/cm, water swell from 30.25 to 66.50%, IEC from 0.38 to 0.82 meq/g, and methanol diffusion coefficients from 3.10 × 10⁻⁷ to 4.82 × 10⁻⁷ cm²/S at 25 °C.     

Crosslinked sulfonated poly(arylene ether sulfone) membranes for fuel cell application

A series of sulfonated poly(arylene ether sulfone) with photocrosslinkable moieties is successfully synthesized by direct copolymerization of 3,3′-disulfonated 4,4′-difluorodiphenyl sulfone (SDFDPS) and 4,4′-difluorodiphenyl sulfone (DFDPS) with 4,4′-biphenol (BP) and 1,3-bis-(4-hydroxyphenyl) propenone (BHPP). The content of crosslinkable moieties in the polymer repeat unit is controlled from 0 to 10 mol% by changing the monomer feed ratio of BHPP to BP. The polymer membranes can be crosslinked by irradiating UV with a wavelength of 365 nm. From FT-IR analysis, it can be identified that UV crosslinking mainly occurs due to the combination reaction of radicals that occurs in conjunction with the breaking of the carbon–carbon double bonds (–CH = CH-) of the chalcone moieties in the backbone. Consequently, a new bond is created to form cyclobutane. The crosslinked membranes show less water uptake, a lower level of methanol permeability, and good thermal and mechanical properties compared to pristine (non-crosslinked) membranes while maintaining a reasonable level of proton conductivity. Finally, the fuel cell performance of the crosslinked membranes is comparable to that of the Nafion 115 membrane, demonstrating that these membranes are promising candidates for use as polymer electrolyte membranes in DMFCs.     

Homologous flexible multi-cationic cross-linkers modified poly(aryl ether sulfone) anion exchange membranes for fuel cell applications

Issues of unsatisfactory ionic conductivity and chemical stability should be solved for anion exchange membranes (AEMs) in practical fuel cell applications. A series of flexible spacers, homologous multi-cationic cross-linkers with different lengths, were designed and synthesized from 1,4-diazabicyclo(2.2.2)octane (DABCO) and 1,6-dibromohexane, and subsequently used to fabricate a series of flexible multi-cationic cross-linked poly(aryl ether sulfone) (CQPAES) AEMs. The CQPAES membranes fabricated by simultaneous cross-linking and membrane formation are tough and pliable. The length and number of cations of the cross-linkers show noticeable effects on the comprehensive membrane performance. The CQPAES membranes display more distinct nano-phase separation morphology and well-developed ion transfer channels due to the higher mobility and hydrophilicity of the flexible long-chain multi-cationic segments. As a result, the CQPAES membranes exhibit gradually increased water uptake and ionic conductivity with the increase of cross-linker length. Furthermore, DABCO and hexyl segments in the cross-linker greatly enhance the steric hindrance and electron cloud density of the quaternary ammonium groups, which inhibit the Hoffmann elimination reaction. Consequently, the CQPAES membranes display a significant improvement in alkali stability than conventional benzyl-substituted quaternary ammonium group type AEMs.     

Preparation of main-chain-type and side-chain-type sulfonated poly(ether ether ketone) membranes for direct methanol fuel cell applications

Novel main-chain-type and side-chain-type sulphonated poly(ether ether ketone)s (MS-SPEEKs) are synthesised by reacting the sulphonic acid groups of pristine SPEEKs with 2-aminoethanesulphonic acid to improve the nano-phase separated morphology of the material. ¹H NMR and FT-IR spectroscopy are employed to determine the structure and composition of main-chain-type and side-chain-type sulphonated polymers. Flexible and tough membranes with reasonable thermal properties are obtained. The MS-SPEEKs show good hydrolytic stability, and water uptake values ranging from 15% to 30% are observed. Compared to Nafion 117^®, the methanol permeability of the MS-SPEEKs is dramatically reduced to 8.83 × 10⁻⁸ cm² s⁻¹ to 3.31 × 10⁻⁷ cm² s⁻¹. The proton conductivity increases with increasing temperature, reaching 0.013-0.182 S cm⁻¹. A maximum power density and open circuit voltage of 115 mW cm⁻² and 0.830 V are obtained at 80 °C, respectively, which is significantly greater than the values generated with Nafion 117^®. The introduction of pendent side-chain-type sulphonic acid groups increases the single-cell performance by more than approximately 20%; thus, the lower water diffusivity, methanol permeability, electro-osmotic drag coefficient and high cell performance indicated that MS-SPEEK is a promising candidate for DMFC applications.     

Synthesis and properties of novel HMS-based sulfonated poly(arylene ether sulfone)/silica nano-composite membranes for DMFC applications

Novel 4,4′-dihydroxy-α-methylstilbene (HMS)-based sulfonated poly(arylene ether sulfone) with sulfonic acid composition ranging from 10 to 40 mol% was synthesized via nucleophilic step polymerization of 4,4′-dihydroxy-α-methylstilbene, 4,4′-dichloro-3,3′-disulfonic acid diphenylsulfone and 4,4′-dichlorodiphenylsulfone and blended with silica sol to form organic/inorganic nano-composite membranes. The organic/inorganic nano-composite copolymers produced show a high glass transition temperature and thermal decomposition temperatures from 318 to 451 °C. The copolymers present appropriate toughness during the membrane process. The equilibrium water uptake and proton conductivity of the obtained organic/inorganic nano-composite membranes were measured as functions of temperature, degree of sulfonation and silica content. In general, the water uptake increased from 8 to 37 wt.%, and the proton conductivity of the organic/inorganic nano-composite membranes increased from 0.003 to 0.110 S cm⁻¹ as the degree of sulfonation increased from 10 to 40 mol%, the silica content increased from 3 to 10 wt.%, and the temperature increased from 30 to 80 °C. The single cell performance of the 40 mol% organic/inorganic nano-composite membrane with various silica contents ranged from 11 to 13 mW cm⁻² at 80 °C, and the power density was higher than Nafion^® 117. Including the thermal properties, swelling, conductivity and single cell performance, the nano-composite membranes are able to satisfy the requirements of proton exchange membranes for direct methanol fuel cells (DMFC).     

Role of post-sulfonation of poly(ether ether sulfone) in proton conductivity and chemical stability of its proton exchange membranes for fuel cell

Commercially available poly(ether ether sulfone), PEES, was directly sulfonated using concentrated sulfuric acid at low temperatures by minimizing degradation during sulfonation. The sulfonation reaction was performed in the temperature range of 5–25 °C. Sulfonated polymers were characterized by FTIR, ¹H NMR spectroscopy and ion exchange capacity (IEC) measurements. Degradation during sulfonation was investigated by measuring intrinsic viscosity, glass transition temperature and thermal decomposition temperature of sulfonated polymers. Sulfonated PEES, SPEES, membranes were prepared by solvent casting method and characterized in terms of IEC, proton conductivity and water uptake. The effect of sulfonation conditions on chemical stability of membranes was also investigated via Fenton test. Optimum sulfonation condition was determined to be 10 °C with conc. H₂SO₄ based on the characteristics of sulfonated polymers and also the chemical stability of their membranes. SPEES membranes exhibited proton conductivity up to 185.8 mS cm⁻¹ which is higher than that of Nafion 117 (133.3 mS cm⁻¹) measured at 80 °C and relative humidity 100%.     

Crosslinked sulfonated poly(ether ether ketone) proton exchange membranes for direct methanol fuel cell applications

In the present study, a series of the crosslinked sulfonated poly(ether ether ketone) (SPEEK) proton exchange membranes were prepared. The photochemical crosslinking of the SPEEK membranes was carried out by dissolving benzophenone and triethylamine photo-initiator system in the membrane casting solution and then exposing the resulting membranes after solvent evaporation to UV light. The physical and transport properties of crosslinked membranes were investigated. The membrane performance can be controlled by adjusting the photoirradiation time. The experimental results showed that the crosslinked SPEEK membranes with photoirradiation 10 min had the optimum performance for proton exchange membranes (PEMs). Compared with the non-crosslinked SPEEK membranes, the crosslinked SPEEK membranes with photoirradiation 10 min markedly improved thermal stabilities and mechanical properties as well as hydrolytic and oxidative stabilities, greatly reduced water uptake and methanol diffusion coefficients with only slight sacrifice in proton conductivities. Therefore, the crosslinked SPEEK membranes with photoirradiation 10 min were particularly promising as proton exchange membranes for direct methanol fuel cell (DMFC) applications.     

Quinoxaline-based crosslinked membranes of sulfonated poly(arylene ether sulfone)s for fuel cell applications

A series of crosslinkable sulfonated poly(arylene ether sulfone)s (SPAESs) were synthesized by copolymerization of 4,4′-biphenol with 2,6-difluorobenzil and 3,3′-disulfonated-4,4′-difluorodiphenyl sulfone disodium salt. Quinoxaline-based crosslinked SPAESs were prepared via the cyclocondensation reaction of benzil moieties in polymer chain with 3,3′-diaminobenzidine to form quinoxaline groups acting as covalent and acid-base ionic crosslinking. The uncrosslinked and crosslinked SPAES membranes showed high mechanical properties and the isotropic membrane swelling, while the later became insoluble in tested polar aprotic solvents. The crosslinking significantly improved the membrane performance, i.e., the crosslinked membranes had the lower membrane dimensional change, lower methanol permeability and higher oxidative stability than the corresponding precursor membranes, with keeping the reasonably high proton conductivity. The crosslinked membrane (CS1-2) with measured ion exchange capacity of 1.53 mequiv. g⁻¹ showed a reasonably high proton conductivity of 107 mS/cm with water uptake of 48 wt.% at 80 °C, and exhibited a low methanol permeability of 2.3 × 10⁻⁷ cm² s⁻¹ for 32 wt.% methanol solution at 25 °C. The crosslinked SPAES membranes have potential for PEFC and DMFCs.     

Preparation and characterization of sulfonated poly(tetra phenyl ether ketone sulfone)s for proton exchange membrane fuel cell

Sulfonated poly(tetra phenyl ether ketone sulfone)s SPTPEKS were successfully synthesized for proton exchange membrane. Poly(tetra phenyl ether ketone sulfone)s PTPEKS were prepared by the 4,4′-dihydroxydiphenylsulfone with 1,2-bis(4-fluorobenzoyl)-3,4,5,6-tetraphenylbenzene (BFBTPB) and 4,4′-difluorodiphenylsulfone, respectively, at 210 °C using potassium carbonate in sulfolane. PTPEKS were followed by sulfonation using chlorosulfonic acid and concentrated sulfuric acid at two stage reactions. Different contents of sulfonated unit of SPTPEKS (17, 20, 23 mol% of BFBTPB) were studied by FT-IR, ¹H NMR spectroscopy, and thermo gravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water. The ion exchange capacity (IEC) and proton conductivity of SPTPEKS were evaluated with increase of degree of sulfonation. The water uptake of synthesized SPTPEKS membranes exhibit 25–61% compared with 28% of Nafion 211^®. The SPTPEKS membranes exhibit proton conductivities (25 °C) of 11.7–25.3 × 10⁻³ S/cm compared with 33.7 × 10⁻³ S/cm of Nafion 211^®.     

Sulfonated poly(ether ether ketone) membranes with sulfonated graphene oxide fillers for direct methanol fuel cells

Sulfonated organosilane functionalized graphene oxides (SSi-GO) synthesized through the grafting of graphene oxide (GO) with 3-mercaptopropyl trimethoxysilane and subsequent oxidation have been used as a filler in sulfonated poly(ether ether ketone) (SPEEK) membranes. The incorporation of SSi-GOs greatly increases the ion-exchange capacity (IEC), water uptake, and proton conductivity of the membrane. With well-controlled contents of SSi-GOs, the composite membranes exhibit higher proton conductivity and lower methanol permeability than Nafion^® 112 and Nafion^® 115, making them particularly attractive as proton exchange membranes (PEMs) for direct methanol fuel cells (DMFC). The composite membrane with optimal SSi-GOs content exhibit over 38 and 17% higher power densities, respectively, than Nafion^® 112 and Nafion^® 115 membranes in DMFCs, offering the possibilities to reduce the DMFC membrane cost significantly while keeping high-performance.     

Nafion/nitrated sulfonated poly(ether ether ketone) membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone)s (SPEEKs) are substituted on the main chain of the polymer by nitro groups and blended with Nafion^® to attain composite membranes. The sulfonation, nitration and blending are achieved with a simple, inexpensive process, and the blended membranes containing the nitrated SPEEKs reveal a liquid-liquid phase separation. The blended membranes have a lower water uptake compared to recast Nafion^®, and the methanol permeability is reduced significantly to 4.29 × 10⁻⁷-5.34 × 10⁻⁷ cm² s⁻¹ for various contents of nitrated SPEEK for S63N17, and 4.72 × 10⁻⁷-7.11 × 10⁻⁷ cm² s⁻¹ for S63N38, with a maximum proton conductivity of ∼0.085 S cm⁻¹. This study examines the single-cell performance at 80 °C of Nafion^®/nitrated SPEEK membranes with various contents of nitrated SPEEK and a degree of nitration of 23-25 mW cm⁻² for S63N17 and 24-29 mW cm⁻² for S63N38. Both the power density and open circuit voltage are higher than those of Nafion^® 115 and recast Nafion^®.     

Sulfonated poly(arylene ether sulfone) membranes blended with hydrophobic polymers for direct methanol fuel cell applications

In this paper, proton exchange membranes for direct methanol fuel cells were prepared by blending sulfonated poly(arylene ether sulfone) with poly (vinylidene fluoride-co-hecafluoropropylene)(PVdF-HFP) and polyethersulfone (PES) to decrease methanol permeability while maintaining high proton conductivity. The content of the second polymer, such as PES and PVdF, in the blend membranes was controlled at 10–40 wt% based on SPAES. In order to investigate the effects of the second polymer content in the blended membranes, parameters of the prepared membranes related to fuel cell performance were characterized, including their morphology, mechanical properties, methanol permeability, and proton conductivity. Surface roughness of the blend membrane was increased by the introduction of a hydrophobic polymer. Mechanical properties of the PES/SPAES blend membrane were improved owing to interaction between the sulfonic acid groups in SPAES and PES. However, the tensile strength of the PVdF/SPAES blend membrane was decreased by due to the poor compatibility of SPAES and PVdF. The methanol permeability in the blended membranes decreased with increasing content of PES and PVdF. The SPAES/PES blend membranes exhibited good proton conductivity and lower methanol permeability than the SPAES membrane. The SVdF15 blend membrane showed the highest selectivity due to the absence of methanol crossover and a small decrease of proton conductivity. These blend membranes are suitable for DMFC applications.     

Novel cross-linked sulfonated poly (arylene ether ketone) membranes for direct methanol fuel cell

To prepare a cross-linked proton exchange membrane with low methanol permeability and high proton conductivity, poly (vinyl alcohol) is first blended with sulfonated poly (arylene ether ketone) bearing carboxylic acid groups (SPAEK-C) and then heated to induce a cross-linking reaction between the carboxyl groups in SPAEK-C and the hydroxyl groups in PVA. Fourier transform infrared spectroscopy is used to characterize and confirm the structure of SPAEK-C and the cross-linked membranes. The proton conductivity of the cross-linked membrane with 15% PVA in weight reaches up to 0.18 S cm⁻¹ at 80 °C (100% relative humidity), which is higher than that of Nafion membrane, while the methanol permeability is nearly five times lower than Nafion. The ion-exchange capacity, water uptake and thermal stability are investigated to confirm their applicability in fuel cells.     

Organic-inorganic crosslinked and hybrid membranes derived from sulfonated poly(arylene ether sulfone)/silica via sol-gel process

A series of covalently crosslinkable organic-inorganic hybrid membranes have been prepared from sulfonated poly(arylene ether sulfone) (SPAES) with pendant propenyl moiety and various amounts of vinyl substituted silica via sol-gel process which are then thermally crosslinked in the presence of benzoyl peroxide (BPO) initiator. The obtained membranes are characterized in terms of oxidative stability, thermal property, ion exchange capacity (IEC), water uptake, swelling ratio in methanol aqueous solution, proton conductivity, and methanol permeability coefficient. The results indicate that the oxidative stability and thermal stability of the hybrid membranes are improved. Moreover, introduction of silica reduces the water uptake and methanol swelling of membranes. The swelling ratio of membranes in 2 mol L⁻¹ methanol aqueous solution at 80 °C slowly decreases from 26 to 19% with the increase of SiO₂ content from 0 to 12 wt.%. Furthermore, with the increase in silica content, the methanol permeability coefficient of the hybrid membranes decreases at first and then increases. When the silica content reaches 8 wt.%, the methanol permeability coefficient is at the minimum of 6.02 × 10⁻⁷ cm² s⁻¹, a 2.64-fold decrease compared with that of the pristine SPAES membrane. Moreover, the proton conductivity is found to be at about 95% of that of pristine polymer at that silica content.     

Improvement of electrochemical performances of sulfonated poly(arylene ether sulfone) via incorporation of sulfonated poly(arylene ether benzimidazole)

In the present study, modified acid–base blend membranes were fabricated via incorporation of sulfonated poly(arylene ether benzimidazole) (SPAEBI) into sulfonated poly(arylene ether sulfone) (SPAES). These membranes had excellent methanol-barrier properties in addition to an ability to compensate for the loss of proton conductivity that typically occurs in general acid–base blend system. To fabricate the membranes, SPAEBIs, which served as amphiphilic polymers with different degrees of sulfonation (0–50 mol%), were synthesized by polycondensation and added to SPAES. It resulted in the formation of acid–amphiphilic complexes such as [PAES-SO₃]⁻⁺[H-SPAEBI] through the ionic crosslinking, which prevented SO₃H groups in the complex from transporting free protons in an aqueous medium, contributing to a reduction of ion exchange capacity values and water uptake in the blend membranes, and leading to lower methanol permeability in a water–methanol mixture. Unfortunately, the ionic bonding formation was accompanied by a decrease of bound water content and proton conductivity, although the latter problem was solved to some extent by the incorporation of additional SO₃H groups in SPAEBI. In the SPAES–SPAEBI blend membranes, enhancement of proton conductivity and methanol-barrier property was prominent at temperatures over 90 °C. The direct methanol fuel cell (DMFC) performance, which was based on SPAES–SPAEBI-50–5, was 1.2 times higher than that of Nafion^® 117 under the same operating condition.     

A novel quaternized poly(ether sulfone) membrane for alkaline fuel cell application

A new type of poly(ether sulfone)‐based self‐aggregated anion exchange membrane (AEM) was successfully synthesized and used in H₂/O₂ fuel cell applications. The self‐aggregated structural design improves the effective mobility of OH^? ion and increases the ionic conductivity of AEM. Proton nuclear magnetic resonance and Fourier transform infrared spectroscopy spectra confirm successful chloromethylation and quaternization in the poly(ether sulfone). Thermogravimetric analysis curves show the self‐aggregated membrane was thermally stable up to 180 °C. The AEM also has excellent mechanical properties, with tensile strength 53.5 MPa and elongation at break 47.6% under wet condition at room temperature. The performance of H₂/O₂ single fuel cell at 30 °C showed the maximum power density of 162 mW cm^?2. These results show that the self‐aggregated quaternized poly(ether sulfone) membrane is a potential candidate for alkaline fuel cell applications. Copyright © 2014 John Wiley & Sons, Ltd.     

Cross-linked miscible blend membranes of sulfonated poly(arylene ether sulfone) and sulfonated polyimide for polymer electrolyte fuel cell applications

Cross-linked miscible blend (CMB) membranes were prepared from sulfonated poly(arylene ether sulfone) (SPAES) and sulfonated polynaphthalimide (SPI). They were transparent and insoluble in solvents. They showed the intermediate properties between SPAES and SPI concerning mechanical strength, water uptake, membrane swelling and proton conductivity. As for membrane swelling and proton conductivity, SPAES was almost isotropic, whereas SPI was highly anisotropic. CMB membranes were moderately anisotropic and had the advantages of the smaller in-plane membrane swelling and the larger through-plane conductivity compared to SPAES and SPI, respectively. Polymer electrolyte fuel cell performance of CMB2 membrane with an equal weight ratio of SPAES/SPI and an ion exchange capacity (IEC) of 1.74 meq g⁻¹ was investigated, compared to SPI membrane (R1) with a slightly higher IEC of 1.86 meq g⁻¹. At 90 °C, 0.1 MPa and relatively high humidification of 82/68% RH or 0.2 MPa and low humidification of 50-30% RH, CMB2 showed the reasonably high cell performances. At 110 °C and 50-33% RH, the cell performance was fairly high only at a high pressure of 0.3 MPa, but low at 0.2-0.15 MPa. At these conditions, the cell performance was better for CMB2 than for R1 due to the more effective back-diffusion of water formed at cathode into membrane. CMB2 showed the fairly high PEFC durability at 110 °C.     

Preparation and characterization of imidazolium-functionalized poly (ether sulfone) as anion exchange membrane and ionomer for fuel cell application

Imidazolium-functionalized anion exchange membranes (AEMs) for anion exchange membrane fuel cells (AEMFCs) were synthesized by functionalization of chloromethylated poly (ether sulfone) (PES) with 1-alkylimidazole. The properties of AEMs can be controlled by the degree of chloromethylation of PES. Moreover, with the increment of the alkyl line length on the imidazolium group, the water uptake, swelling ratio and solubility of AEMs increased, whereas the hydroxide conductivity declined. By dissolving AEMs in the mixture of ethanol and water, IM-based anion exchange ionomers (AEIs) can be obtained. Electrochemical studies revealed that the catalytic activities of Pt/C towards oxygen reduction and hydrogen oxidation in the presence of imidazolium-functionalized AEIs were almost the same with that of commercial quaternary ammonium-based ionomers. The fabricated AEM and AEI were utilized to assemble H₂/O₂ AEMFC, yielding a peak power density of ∼30 mW cm⁻² with open circuit potential larger than 1.0 V. The results obtained indicate that imidazolium-functionalized AEMs and AEIs may be candidates which are worth further investigation for the application in the AEMFCs.     

Progress in poly(phenylene oxide) based cation exchange membranes for fuel cells and redox flow batteries applications

In fuel cell technologies, low-temperature proton exchange membrane fuel cells (LT-PEMFC), high-temperature proton exchange membrane fuel cells (HT- PEMFC), and direct methanol fuel cells (DMFC) are gained significant attention as a promising energy system for practical applications. The developments of cost-effective membrane materials with excellent physicochemical properties are indispensable for replacing the high cost of commercial membranes and achieving the higher performance of fuel cell systems. This review focuses on the developments and modifications of cost-effective poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) as a cation exchange membrane for LT-PEMFC, HT- PEMFC and DMFC. Notably, this review bridges the understanding of PPO based membranes, current advancements, structure, physicochemical properties and fuel cell performances. Progressive developments and a systematic overview of PPO-based membrane developments are explained in detail in terms of functionalization, blend, composite, acid-base, cross-linking, copolymerization, coated and reinforcement. Moreover, the changes in physicochemical properties and fuel cell performances in the membrane are deeply reviewed. Additionally, the utilization of PPO based membranes in different kinds of redox flow battery systems are reviewed. Overall, this review provides an exclusive vision and perspectives to develop the PPO based advanced, cost-effective, and high-performance membranes for fuel cell technologies and redox flow battery systems.     

4-Aminopyridine grafted sulfonated poly(arylene ether ketone sulfone) proton exchange membrane with high relative selectivity for fuel cells

A series of sulfonated poly(arylene ether ketone sulfone)s polymer having a degree of sulfonation of 80% and a carboxyl group in the side chain (C-SPAEKS) were prepared by polycondensation. The 4-aminopyridine grafted sulfonated poly(arylene ether ketone sulfone)s polymer membranes (SPPs) were prepared by amidation reaction with the carboxyl group to immobilize 4-aminopyridine on the side chain. The ¹H NMR results and Fourier transform infrared of SPP membranes demonstrated the successful grafting of the 4-aminopyridine. Proton conductivity, water absorption, swelling ratio, and thermal stability of different proportions of SPP membranes were investigated under the different conditions. With the increase of pyridine grafting content, the methanol permeability coefficient of the membrane decreased significantly from 8.17 × 10⁻⁷ cm²s⁻¹ to 8.92 × 10⁻⁸ cm²s⁻¹ at 25 °C. And, the proton conductivity and relative selectivity of the membrane were positively correlated with the grafted pyridine content. Among them, the SPP-4 membrane exhibited the highest proton conductivity of 0.088 Scm⁻¹ at 100 °C. The relative selectivity increased from 4.73 × 10⁴ S scm⁻³ to 9.84 × 10⁴ S scm⁻³.