The effect of preparation method on the catalytic performance over superior MgO-promoted Ni–Ce0.8Zr0.2O2 catalyst for CO2 reforming of CH4

The effect of preparation method on MgO-promoted Ni–Ce_0.8Zr_0.2O₂ catalysts was investigated in CO₂ reforming of CH₄. Co-precipitated Ni–MgO–Ce_0.8Zr_0.2O₂ exhibited very high activity as well as stability (X_CH4 > 95% at 800 °C for 200 h) due to high surface area, high dispersion of Ni, small Ni crystallite size, and easier reducibility. Four elements (Ni, Mg, Ce, and Zr) are located at the same position for the co-precipitated catalyst, resulting in easier reducibility.     

Effect of milling methods on performance of Ni–Y2O3-stabilized ZrO2 anode for solid oxide fuel cell

A Ni–YSZ (Y₂O₃-stabilized ZrO₂) composite is commonly used as a solid oxide fuel cell anode. The composite powders are usually synthesized by mixing NiO and YSZ powders. The particle size and distribution of the two phases generally determine the performance of the anode. Two different milling methods are used to prepare the composite anode powders, namely, high-energy milling and ball-milling that reduce the particle size. The particle size and the Ni distribution of the two composite powders are examined. The effects of milling on the performance are evaluated by using both an electrolyte-supported, symmetric Ni–YSZ/YSZ/Ni–YSZ cell and an anode-supported, asymmetric cell. The performance is examined at 800 °C by impedance analysis and current-voltage measurements.     

Ni–SiO2 and Ni–Fe–SiO2 catalysts for methane decomposition to prepare hydrogen and carbon filaments

Active and stable Ni–Fe–SiO₂ catalysts prepared by sol–gel method were employed for direct decomposition of undiluted methane to produce hydrogen and carbon filaments at 823 K and 923 K. The results indicated that the lifetime of Ni–Fe–SiO₂ catalysts was much longer than Ni–SiO₂ catalyst at a higher reaction temperature such as 923 K, however, a reverse trend was shown when methane decomposition took place at a lower reaction temperature such as 823 K. XRD studies suggested that iron atoms had entered into the Ni lattice and Ni–Fe alloy was formed in Ni–Fe–SiO₂ catalysts. The structure of the carbon filaments generated over Ni–SiO₂ and Ni–Fe–SiO₂ was quite different. TEM studies showed that “multi-walled” carbon filaments were formed over 75%Ni–25%SiO₂ catalyst, while “bamboo-shaped” carbon filaments generated over 35%Ni–40%Fe–25%SiO₂ catalysts at 923 K. Raman spectra of the generated carbons demonstrated that the graphitic order of the “multi-walled” carbon filaments was lower than that of the “bamboo-shaped” carbon filaments.     

Catalytic behavior of Ni/ZrxTi1−xO2 and the effect of SiO2 doping in oxidative steam reforming of n-butane

Catalytic behaviors of TiO₂-, Zr_0.5Ti_0.5O₂-, and ZrO₂-supported Ni catalysts were investigated for oxidative steam reforming of n-C₄H₁₀ at 723 K. The composite oxide support, Zr_0.5Ti_0.5O₂, shows high specific surface area (136 m²/g), leading to fine Ni particles. Thus, the Ni/Zr_0.5Ti_0.5O₂ catalyst exhibits higher and more stable activity than that exhibited by other catalysts. However, relatively large amounts of coke are deposited on the catalyst during reaction. Thus, to retard carbon deposition, the influence of SiO₂ additive was studied. Large amounts of SiO₂ additive (5 or 10 mol%) decrease initial activity; at 10 mol%, degradation is also induced by oxidation of Ni⁰. However, small amounts of SiO₂ additive (1.5 mol%) effectively retard coking without lowering initial activity. The resultant Ni/Zr_0.5Ti_0.5O₂–SiO₂ (1.5 mol%) catalyst exhibits high and stable activity without coking.     

Nanocomposite Ni/ZrO2: Highly active and stable catalyst for H2 production via cyclic stepwise methane reforming reactions

This work investigates the catalytic performance of nanocomposite Ni/ZrO₂-AN catalyst consisting of comparably sized Ni (10–15 nm) and ZrO₂ (15–25 nm) particles for hydrogen production from the cyclic stepwise methane reforming reaction with either steam (H₂O) or CO₂ at 500–650 °C, in comparison with a conventional Ni/ZrO₂-CP catalyst featuring Ni particles supported by large and widely sized ZrO₂ particles (20–400 nm). Though both catalysts exhibited similar activity and stability during the reactions at 500 and 550 °C, they showed remarkably different catalytic stabilities at higher temperatures. The Ni/ZrO₂-CP catalyst featured a significant deactivation even during the methane decomposition step in the first cycle of the reactions at ≥600 °C, but the Ni/ZrO₂-AN catalyst showed a very stable activity during at least 17 consecutive cycles in the cyclic reaction with steam. Changes in the catalyst beds at varying stages of the reactions were characterized with TEM, XRD and TPO–DTG and were correlated with the amount and nature of the carbon deposits. The Ni particles in Ni/ZrO₂-AN became stabilized at the sizes of around 20 nm but those in Ni/ZrO₂-CP kept on growing in the methane decomposition steps of the cyclic reaction. The small and narrowly sized Ni particles in the nanocomposite Ni/ZrO₂-AN catalyst led to a selective formation of filamentous carbons whereas the larger Ni particles in the Ni/ZrO₂-CP catalyst a preferred formation of graphitic encapsulating carbons. The filamentous carbons were favorably volatilized in the steam treatment step but the CO₂ treatment selectively volatilized the encapsulating carbons. These results identify that the nature but not the amount of carbon deposits is the key to the stability of Ni/ZrO₂ catalyst and that the nanocomposite Ni/ZrO₂-AN would be a promising catalyst for hydrogen production via cyclic stepwise methane reforming reactions.     

Synthesis gas production in the combined CO2 reforming with partial oxidation of methane over Ce-promoted Ni/SiO2 catalysts

A series of nickel-based catalyst supported on silica (Ni/SiO₂) with different loading of Ce/Ni (molar ratio ranging from 0.17 to 0.84) were prepared using conventional co-impregnation method and were applied to synthesis gas production in the combination of CO₂ reforming with partial oxidation of methane. Among the cerium-containing catalysts, the cerium-rich ones exhibited the higher activity and stability than the cerium-low ones. The temperature-programmed reduction (TPR) and UV–vis diffuse reflectance spectroscopy (UV–vis DRS) analysis revealed that the addition of CeO₂ reduced the chemical interaction between Ni and support, resulting in an increase in reducibility and dispersion of Ni. Over NiCe-x/SiO₂ (x = 0.17, 0.50, 0.67, 0.84) catalysts, the reduction peak in TPR profiles shifted to the higher temperature with increasing Ce/Ni molar ratio, which was attributed to the smaller metallic nickel size of the reduced catalysts. The transmission electron microscopy (TEM) and X-ray diffraction (XRD) for the post-reaction catalysts confirmed that the promoter retained the metallic nickel species and prevented the metal particle growth at high reaction temperature. The NiCe-0.84/SiO₂ catalyst with small Ni particle size exhibited the stable activity with the constant H₂/CO molar ratio of 1.2 during 6-h reaction in the combination of CO₂ reforming with partial oxidation of methane at 850 °C and atmospheric pressure.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

Combination of CO2 reforming and partial oxidation of methane to produce syngas over Ni/SiO2 and Ni–Al2O3/SiO2 catalysts with different precursors

Ni/SiO₂ and Ni–Al₂O₃/SiO₂ catalysts were prepared by incipient wetness impregnation using citrate and nitrate precursors and tested with a reaction of combination of CO₂ reforming and partial oxidation of methane to produce syngas (H₂/CO). The catalytic activity of Ni/SiO₂ and Ni–Al₂O₃/SiO₂ greatly depended on interaction between NiO and support. NiO strongly interacted with support formed small nickel particles (about 4 nm for NiSC which is abbreviation of Ni/SiO₂ prepared with Nickel citrate precursor) after reduction. The small nickel particles over NiSC catalysts exhibited a good catalytic performance.     

Effect of Ca,Ce or K oxide addition on the activity of Ni/SiO2 catalysts for the methane decomposition reaction

To increase the activity and stability of Ni/SiO₂ catalysts, a series of Ni–Ca, Ni–K and Ni–Ce promoted catalysts were prepared by successive impregnations. The textural properties, reducibility and catalytic performance in the methane decomposition reaction were investigated. The catalyst containing 30 wt.% Ni and 30 wt.% cerium oxide greatly increased the conversion of methane (90% of equilibrium value) and improved the stability, whereas the Ni–K and Ni–Ca were less active and stable than the Ni/SiO₂ catalyst. The results suggest that Ce addition prevents the sintering of nickel particles during reduction process maintaining a random distribution between the silica and cerium oxide improving the distribution and migration of deposited carbon.     

Reaction pathway for ethanol steam reforming on a Ni/SiO2 catalyst including coke formation

The effect operating conditions (temperature, space time, steam/ethanol molar ratio, ethanol partial pressure and time on stream) have on the activity and stability of a Ni/SiO₂ catalyst for H₂ production by ethanol steam reforming has been studied in a fluidized bed reactor. This catalyst allows obtaining total conversion above 500 °C, with a steam/ethanol molar ratio of 6 and a space time of 0.138 g_catalysth/g_ethanol. Catalyst deactivation in the 300–500 °C range is due to coke deposition, whose nature (determined by TPH and TPO analysis) mainly depends on reaction temperature. The coke deposited at 300 °C is amorphous and blocks metallic sites, whereas at higher temperatures the coke is mainly filamentous and, although its content increases as reaction temperature is raised to 500 °C, it has a low effect on catalyst deactivation because it does not block metal sites. Above 600 °C the decrease in coke content due to gasification is noticeable, although at this temperature an incipient Ni sintering is observed, which is significant at 700 °C.     

Improvement of the stability of a ZrO2-modified Ni–nano-CaO sorption complex catalyst for ReSER hydrogen production

A Ni–nano-CaO sorption complex catalyst was modified with ZrO₂ to improve its stability for use in hydrogen production from steam methane reforming (SMR). Nano-ZrO₂ was introduced into a support containing nano-CaCO₃ and Al₂O₃. The sorption complex catalyst, ZrO₂–Ni–nano-CaO, was prepared by infusing Ni into the ZrO₂–nano-CaO support, followed by calcination. The catalyst was evaluated with a bench-scale fixed bed reactor under the following reaction conditions: a temperature of 600 °C, a steam–carbon mole ratio of 4:1, a gas hourly space velocity of 1800 h⁻¹, and a regeneration temperature of 800 °C. The reaction was performed under an atmosphere of nitrogen. The ZrO₂-modified sorption complex catalyst could achieve 20 cyclic runs of ReSER hydrogen production, while the sorption complex catalyst without the ZrO₂ modification rapidly deactivated after three cyclic runs. Brunauer–Emmer–Teller analysis showed that the catalyst surface area of the new catalyst had increased. Furthermore, the addition of ZrO₂ could prevent the formation of NiAl₂O₄ in the sorption complex catalyst, which we believe to be the main cause of the improvement in the catalyst stability.     

Non-thermal plasma assisted synthesis and physicochemical characterizations of Co and Cu doped Ni/Al2O3 nanocatalysts used for dry reforming of methane

Ni/Al₂O₃ nanocatalysts doped with Co and Cu were prepared by co-impregnation and modified by non-thermal plasma. The nanocatalysts were characterized by XRD, FESEM, TEM, EDX dot-mapping, BET, FTIR, TGA-DTG, and XPS analysis. According to XRD and XPS results, good interaction between active phase and support can be observed in both Ni–Co/Al₂O₃ and Ni–Cu/Al₂O₃ nanocatalysts. A uniform morphology, high surface area, and well dispersed particles of active sites in Ni–Co/Al₂O₃ nanocatalyst were observed that shows the effect of cobalt in controlling Ni ensemble size. In contrast Ni–Cu/Al₂O₃ nanocatalyst had no homogenous dispersion of active phase due to sintering of copper particles. The activity measurements illustrated better Ni–Co/Al₂O₃ nanocatalyst activity in comparison to Ni/Al₂O₃ and Ni–Cu/Al₂O₃ in terms of CH₄ and CO₂ conversion. H₂ and CO yield were higher for Ni–Co/Al₂O₃ and higher H₂/Co ratio was obtained as well. Whereas Ni/Al₂O₃ and Ni–Co/Al₂O₃ did not experience deactivation, Ni–Cu/Al₂O₃ suffered from activity loss by ca. 22% and 16% for CH₄ and CO₂ conversion, respectively. Sintering most likely happened in Ni–Cu/Al₂O₃ nanocatalyst due to high temperature of calcination while cobalt by controlling the size of Ni particles, alternated the size of active sites to a size range in which carbon formation was suppressed. Ni/Al ratio from XPS analysis which signifies Ni dispersion on alumina support was 5.15, 9.16, and 6.35 for Ni/Al₂O₃, Ni–Co/Al₂O₃, and Ni–Cu/Al₂O₃ nanocatalysts respectively. The highest ratio of Ni/Al was for Ni–Co/Al₂O₃ nanocatalyst that shows the best coverage of support by Ni active phase in this nanocatalyst.     

Influence of metal oxide on LiBH4/2LiNH2/MgH2 system for hydrogen storage properties

In this study, various nanoscale metal oxide catalysts, such as CeO₂, TiO₂, Fe₂O₃, Co₃O₄, and SiO₂, were added to the LiBH₄/2LiNH₂/MgH₂ system by using high-energy ball milling. Temperature programmed desorption and MS results showed that the Li–Mg–B–N–H/oxide mixtures were able to dehydrogenate at much lower temperatures. The order of the catalytic effect of the studied oxides was Fe₂O₃ > Co₃O₄ > CeO₂ > TiO₂ > SiO₂. The onset dehydrogenation temperature was below 70 °C for the samples doped with Fe₂O₃ and Co₃O₄ with 10 wt.%. More than 5.4 wt.% hydrogen was released at 140 °C. X-ray diffraction indicated that the addition of metal oxides inhibited the formation of Mg(NH₂)₂ during ball milling processes. It is thought that the changing of the ball milling products results from the interaction of oxide ions in metal oxide catalysts with hydrogen atoms in MgH₂. The catalytic effect depends on the activation capability of oxygen species in metal oxides on hydrogen atoms in hydrides.     

Y2O3-promoted NiO/SBA-15 catalysts highly active for CO2/CH4 reforming

A series of Y₂O₃-promoted NiO/SBA-15 (9 wt% Ni) catalysts (Ni:Y weight ratio = 9:0, 3:1, 3:2, 1:1) were prepared using a sol–gel method. The fresh as well as the catalysts used in CO₂ reforming of methane were characterized using N₂-physisorption, XRD, FT-IR, XPS, UV, HRTEM, H₂-TPR, O₂-TPD and TG techniques. The results indicate that upon Y₂O₃ promotion, the Ni nanoparticles are highly dispersed on the mesoporous walls of SBA-15 via strong interaction between metal ions and the HO–Si-groups of SBA-15. The catalytic performance of the catalysts were evaluated at 700 °C during CH₄/CO₂ reforming at a gas hourly space velocity of 24 L g_cat⁻¹ h⁻¹(at 25 ^°C and 1 atm) and CH₄/CO₂molar ratio of 1. The presence of Y₂O₃ in NiO/SBA-15 results in enhancement of initial catalytic activity. It was observed that the 9 wt% Y–NiO/SBA-15 catalyst performs the best, exhibiting excellent catalytic activity, superior stability and low carbon deposition in a time on stream of 50 h.     

Combined catalytic partial oxidation and CO2 reforming of methane over ZrO2-modified Ni/SiO2 catalysts using fluidized-bed reactor

Nickel on zirconium-modified silica was prepared and tested as a catalyst for reforming methane with CO₂ and O₂ in a fluidized-bed reactor. A conversion of CH₄ near thermodynamic equilibrium and low H₂/CO ratio (1<H₂/CO<2) were obtained without catalyst deactivation during 10 h, in a most energy efficient and safe manner. A weight loading of 5 wt% zirconium was found to be the optimum. The catalysts were characterized using X-ray diffraction (XRD), H₂-temperature reaction (H₂-TPR), CO₂-temperature desorption (CO₂-TPD) and transmission election microscope (TEM) techniques. Ni sintering was a major reason for the deactivation of pure Ni/SiO₂ catalysts, while Ni dispersed highly on a zirconium-promoted Ni/SiO₂ catalyst. The different kinds of surface Ni species formed on ZrO₂-promoted catalysts might be responsible for its high activity and good resistance to Ni sintering.     

Co and Ni supported on CeO2 as selective bimetallic catalyst for dry reforming of methane

Co/CeO₂ (Co 7.5 wt.%), Ni/CeO₂ (Ni 7.5 wt.%) and Co–Ni/CeO₂ (Co 3.75 wt.%, Ni 3.75 wt.%) catalysts were prepared by surfactant assisted co-precipitation method. Samples were characterized by X-Ray diffraction, BET surface areas measurements, temperature programmed reduction and tested for the dry reforming of methane CH₄ + CO₂ → 2CO + 2H₂ in the temperature range 600–800 °C with a CH₄:CO₂:Ar 20:20:60 vol.% feed mixture and a total flow rate of 50 cm³ min⁻¹ (GHSW = 30,000 mL g⁻¹ h⁻¹). The bimetallic Co–Ni/CeO₂ catalyst showed higher CH₄ conversion in comparison with monometallic systems in the whole temperature range, being 50% at 600 °C and 97% at 800 °C. H₂/CO selectivity decreased in the following order: Co–Ni/CeO₂ > Ni/CeO₂ > Co/CeO₂. Carbon deposition on spent catalysts was analyzed by thermal analysis (TG-DTA). After 20 h under stream at 750 °C, cobalt-containing catalysts, Co/CeO₂ and Co–Ni/CeO₂, showed a stable operation in presence of a deposited amorphous carbon of 6 wt.%, whereas Ni/CeO₂ showed an 8% decrease of catalytic activity due to a massive presence of amorphous and graphitic carbon (25 wt.%).     

Ni/YSZ and Ni–CeO2/YSZ anodes prepared by impregnation for solid oxide fuel cells

In this paper, Ni/YSZ and Ni–CeO₂/YSZ anodes for a solid oxide fuel cell (SOFC) were prepared by tape casting and vacuum impregnation. By this method, the Ni content in the anode could be reduced compared to the traditional tape casting method. It was found that adding CeO₂ into the Ni/YSZ anode by a Ni(NO₃)₂ and Ce(NO₃)₃ mixed impregnation could further enhance cell performance. This was investigated in H₂ at 1073 K. XRD patterns indicated that CeO₂ and Ni were separate phases, and the CeO₂ addition could enhance the Ni dispersion on the YSZ framework surface which was observed by SEM images. It was shown that adding CeO₂ into the Ni anodes could decrease the cell polarization resistance. The maximum power density for cells with 25 wt.% Ni, 5 wt.% CeO₂–25 wt.% Ni/YSZ, or 10 wt.% CeO₂–25 wt.% Ni/YSZ anode was 230 mW cm⁻², 420 mW cm⁻² and 530 mW cm⁻², respectively, in H₂ at 1073 K. The OCV for these cells was 1.05–1.09 V, indicating that a dense electrolyte film was obtained by co-firing porous YSZ layer and dense YSZ layer.     

Production of hydrogen and nanofibrous carbon by selective catalytic decomposition of propane

The process of production of highly concentrated CO_x-free hydrogen and nanofibrous carbon (NFC) by catalytic propane decomposition on Ni and Ni–Cu catalysts (different in active phase composition) at relatively low temperatures (400–700 °C) was investigated. The bimetallic Ni–Cu catalysts showed significantly higher propane conversion and longer lifetime than monometallic Ni catalyst. The Ni (50 wt.%)–Cu (40 wt.%)/SiO₂ catalyst exhibited the best activity and selectivity at 600 °C. Total hydrogen yield of 60.8 mol H₂/g_cat (during 24 h time on stream) and the total H₂:CH₄ ratio of 8.4 were obtained during propane decomposition under these optimal conditions. The possible reaction scheme of propane decomposition over Ni-based catalysts and the reasons of increasing the selectivity of hydrogen are discussed.     

Production of hydrogen by methane catalytic decomposition over Ni–Cu–Fe/Al2O3 catalyst

Catalysts with high nickel concentrations 75%Ni–12%Cu/Al₂O₃, 70%Ni–10%Cu–10%Fe/Al₂O₃ were prepared by mechanochemical activation and their catalytic properties were studied in methane decomposition. It was shown that modification of the 75%Ni–12%Cu/Al₂O₃ catalyst with iron made it possible to increase optimal operating temperatures to 700–750 °C while maintaining excellent catalyst stability. The formation of finely dispersed Ni–Cu–Fe alloy particles makes the catalysts stable and capable of operating at 700–750 °C in methane decomposition to hydrogen and carbon nanofibers. The yield of carbon nanofibers on the modified 70%Ni–10%Cu–10%Fe/Al₂O₃ catalyst at 700–750 °C was 150–160 g/g. The developed hydrogen production method is also efficient when natural gas is used as the feedstock. An installation with a rotating reactor was developed for production of hydrogen and carbon nanofibers from natural gas. It was shown that the 70%Ni–10%Cu–10%Fe/Al₂O₃ catalyst could operate in this installation for a prolonged period of time. The hydrogen concentration at the reactor outlet exceeded 70 mol%.     

Synthesis and electrochemical properties of Li1−xFe0.8Ni0.2O2–LixMnO2 (Mn/(Fe + Ni + Mn) = 0.8) material

A new type of Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ (Mn/(Fe + Ni + Mn) = 0.8) material was synthesized at 350 °C in air atmosphere using a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−xFeO₂–Li_xMnO₂ (Mn/(Fe + Mn) = 0.8) with much reduced impurity peaks. The Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell showed a high initial discharge capacity above 192 mAh g⁻¹, which was higher than that of the parent Li/Li_1−xFeO₂–Li_xMnO₂ (186 mAh g⁻¹). We expected that the increase of initial discharge capacity and the change of shape of discharge curve for the Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell is the result from the redox reaction from Ni²⁺ to Ni³⁺ during charge/discharge process. This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles.