Design of a novel biohythane process with high H2 and CH4 production rates

A biohythane process based on wheat straw including: i) pretreatment, ii) H₂ production using Caldicellulosiruptor saccharolyticus, iii) CH₄ production using an undefined consortium, and iv) gas upgrading using an amine solution, was assessed through process modelling including cost and energy analysis. According to simulations, a biohythane gas with the composition 46–57% H₂, 43–54% CH₄ and 0.4% CO₂, could be produced at high production rates (2.8–6.1 L/L/d), with 93% chemical oxygen demand (COD) reduction, and a net energy yield of 7.4–7.7 kJ/g dry straw. The model was calibrated and verified using experimental data from dark fermentation (DF) of wheat straw hydrolysate, and anaerobic digestion of DF effluent. In addition, the effect of gas recirculation was investigated by both wet experiments and simulation. Sparging improved H₂ productivities and yields, but negatively affected the net energy gain and cost of the overall process.     

Dilute-acid pretreatment of barley straw for biological hydrogen production using Caldicellulosiruptor saccharolyticus

The main objective of this study was to use the fermentability test to investigate the feasibility of applying various dilute acids in the pretreatment of barley straw for biological hydrogen production. At a fixed acid loading of 1% (w/w dry matter) 28–32% of barley straw was converted to soluble monomeric sugars, while at a fixed combined severity of −0.8 30–32% of the straw was converted to soluble monomeric sugars. With fermentability tests at sugar concentrations 10 and 20 g/L the extreme thermophilic bacterium Caldicellulosiruptor saccharolyticus showed good hydrogen production on hydrolysates of straw pretreated with H₃PO₄ and H₂SO₄, and to a lesser extent, HNO₃. The fermentability of the hydrolysate of straw pretreated with HCl was lower compared to the other acids but equally high as that of pure sugars. At sugar concentration 30 g/L the fermentability of all hydrolysates was low.     

Optimization of biogas production from wheat straw stillage in UASB reactor

In the present study, thermophilic anaerobic digestion of wheat straw stillage was investigated. Methane potential of stillage was determined in batch experiments at two different substrate concentrations. Results showed that higher methane yields of 324 ml/g-(volatile solids) VS_added were obtained at stillage concentrations of 12.8 g-VS/L than at 25.6 g-VS/l. Continuous anaerobic digestion of stillage was performed in an up-flow anaerobic sludge blanket (UASB) reactor at 55 °C with 2 days hydraulic retention time. Results showed that both substrate concentration and organic loading rate (OLR) influenced process performance and methane yields. Maximum methane yield of 155 ml CH₄/g-COD was obtained at stillage mixtures with water of 25% (v/v) in the feed and at an OLR of 17.1 g-COD/(l.d). Soluble chemical oxygen demand (SCOD) removal at this OLR was 76% (w/w). Increase in OLR to 41.2 g-COD/(l.d) and/or stillage concentration in the feed to 33–50% (v/v) resulted in low methane yields or complete process failure. The results showed that thermophilic anaerobic digestion of wheat straw stillage alone for methane production is feasible in UASB reactor at an OLR of 17.1 g-COD/(l.d) and at substrate concentration of 25% in the feed. The produced methane could improve the process energy and economics of a bioethanol plant and also enable to utilize the stillage in a sustainable manner.     

Two-stage UASB reactor converting coffee drink manufacturing wastewater to hydrogen and methane

In this study, the feasibility of a continuous two-stage up-flow anaerobic sludge blanket (UASB) reactor system, consisted of thermophilic (55 °C) dark fermentative H₂ production and mesophilic (35 °C) CH₄ production from coffee drink manufacturing wastewater (CDMW), was tested. A recently proposed operational strategy was used to overcome a major drawback of the long start-up period of the UASB reactor. Firstly, a completely stirred tank reactor (CSTR) was operated for 8 days to prepare seeding. The seed was then directly transferred to the UASB reactor. Microbial aggregation took place in the initial period, and the floc size was gradually increased over time. In UASB reactor, the maximum H₂ yield of 2.57 mol H₂/mol hexose_added and a stable H₂ production rate of 4.24 L H₂/L/h were observed at a hydraulic retention time (HRT) of 6 h and substrate concentration of 20 g Carbo. COD/L. In this novel method using CDMW, thermophilic H₂-producing granules with an average particle size of 1.3 mm was successfully developed after 100 days. The more bioenergy recovery was attempted in a post-treatment process using a mesophilic UASB reactor for CH₄ production from the H₂ fermented effluent. The maximum CH₄ yield of 325 mL of CH₄/g COD was achieved with removing 93% of the COD at an organic loading rate of 3.5 g COD/L/d. The developed two-stage UASB reactor system achieved biogas conversion by 88.2% (H₂ 15.2% and CH₄ 73%) and COD removal by 98%.     

Application of immobilized upflow anaerobic sludge blanket reactor using Clostridium LS2 for enhanced biohydrogen production and treatment efficiency of palm oil mill effluent

Polyethylene glycol (PEG) gel was used to immobilize hydrogen producing Clostridium LS2 bacteria for hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. The UASB reactor with a PEG-immobilized cell packing ratio of 10% weight to volume ratio (w/v) was optimal for dark hydrogen production. The performance of the UASB reactor fed with palm oil mill effluent (POME) as a carbon source was examined under various hydraulic retention time (HRT) and POME concentration. The best volumetric hydrogen production rate of 365 mL H₂/L/h (or 16.2 mmol/L/h) with a hydrogen yield of 0.38 L H₂/g COD_added was obtained at POME concentration of 30 g COD/L and HRT of 16 h. The average hydrogen content of biogas and COD reduction were 68% and 65%, respectively. The primary soluble metabolites were butyric acid and acetic acid with smaller quantities of other volatile fatty acid and alcohols formed during hydrogen fermentation. More importantly, the feasibility of PEG-immobilized cell UASB reactor for the enhancement of the dark-hydrogen production and treatment of wastewater is demonstrated.     

Hydrogen and methane production via a two-stage processes (H2-SBR + CH4-UASB) using tequila vinasses

The feasibility of producing hydrogen and methane via a two-stage fermentation of tequila vinasses was evaluated in sequencing batch (SBR) and up-flow anaerobic sludge blanket (UASB) reactors. Different vinasses concentrations ranging from 500 mg COD/L to 16 g COD/L were studied in SBR by using thermally pre-treated anaerobic sludge as inoculum for hydrogen production. Peak volumetric hydrogen production rate and specific hydrogen production were attained as 57.4 ± 4.0 mL H₂/L-h and 918 ± 63 mL H₂/gVSS-d, at the substrate concentration of 16 g COD/L and 6 h of hydraulic retention time (HRT). Increasing substrate concentration has no effect on the specific hydrogen production rate. The fermentation effluent was used for methane production in an UASB reactor. The higher methane composition in the biogas was achieved as 68% at an influent concentration of 1636 mg COD/L. Peak methane volumetric, specific production rates and yield were attained as 11.7 ± 0.7 mL CH₄/L-h, 7.2 ± 0.4 mL CH₄/g COD-h and 257.9 ± 13.8 mL CH₄/g COD at 24 h-HRT and a substrate concentration of 1636 mg COD/L. An overall organic matter removal (SBR + UASB) in this two-stage process of 73–75% was achieved.     

Improving methane content and yield from rice straw by adding extra hydrogen into a two-stage anaerobic digestion system

This study was aimed to increase both the methane content and yield from rice straw by adding extra H₂ into a two-stage anaerobic digestion system. The results showed that the efficiency of H₂ utilization was 36.43%. Of the total amount of H₂ used, 47.3% was converted to CH₄, thereby increasing the CH₄ content and yield by 45% and 101%, respectively. This conversion was performed at a H₂/CO₂ ratio of 4/1 and a recycling frequency of two times a day in an up-flow reactor (UR). Due to the different ways of CH₄ production in continuously stirred tank reactor (CSTR) and UR, ethanol and acetate were produced as intermediaries, accounting for 65% and 87% of total intermediaries, respectively. Moreover, the pH values in CSTR and UR were 6.7 and 8.1, respectively. The results of the microbial community structures showed that the archaea genera of Methanosaeta and Methanobacterium were the most dominant in CSTR, whereas, Methanosaeta was the most dominant in UR. In terms of the bacterial community, Clostridia was the most abundant class in UR. Based on the results mentioned above, it is feasible to simultaneously improve both the CH₄ content and yield from rice straw by adding extra H₂ into the two-stage anaerobic digestion system.     

Dark fermentative hydrogen production from xylose by a hot spring enrichment culture

Dark fermentative hydrogen production by a hot spring culture was studied from different sugars in batch assays and from xylose in continuous stirred tank reactor (CSTR) with on-line pH control. Batch assays yielded hydrogen in following order: xylose > arabinose > ribose > glucose. The highest hydrogen yield in batch assays was 0.71 mol H₂/mol xylose. In CSTR the highest H₂ yield and production rate at 45 °C were 1.97 mol H₂/mol xylose and 7.3 mmol H₂/h/L, respectively, and at 37 °C, 1.18 mol H₂/mol xylose and 1.7 mmol H₂/h/L, respectively. At 45 °C, microbial community consisted of only two bacterial strains affiliated to Clostridium acetobutulyticum and Citrobacter freundii, whereas at 37 °C six Clostridial species were detected. In summary hydrogen yield by hot spring culture was higher with pentoses than hexoses. The highest H₂ production rate and yield and thus, the most efficient hydrogen producing bacteria were obtained at suboptimal temperature of 45 °C for both mesophiles and thermophiles.     

The effects of seed sludge and hydraulic retention time on the production of hydrogen from a cassava processing wastewater and glucose mixture in an anaerobic fluidized bed reactor

The potential for co-fermentation of a cassava processing wastewater and glucose mixture was studied in anaerobic fluidized bed reactors. The effects of different hydraulic retention times (HRTs) (10–2 h) and varying sources of inoculum are reported. The sludge from a UASB reactor that had been used to treat poultry slaughterhouse wastewater (SP) resulted in the highest yields of hydrogen (HY) and ethanol (EtOHY) of 1.0 mmol H₂ g⁻¹ COD (10 h) and 3.0 mmol EtOH g⁻¹ COD (6 h). The sludge from a UASB reactor used for the treatment of swine wastewater (SW) resulted in a maximum HY of 0.65 mmol H₂ g⁻¹ COD (6 h) and EtOHY of 2.1 mmol g⁻¹ COD (10 and 8 h). Methane was produced with a maximum production of 9.68 L CH₄ d⁻¹ L⁻¹. Based on phylogenetic analysis of 16S rRNA, bacteria and methanogenic archaea similar to Lactobacillus and Methanobacterium, respectively, were identified.     

Microbial culture selection for bio-hydrogen production from waste ground wheat by dark fermentation

Hydrogen formation performances of different anaerobic bacteria were investigated in batch dark fermentation of waste wheat powder solution (WPS). Serum bottles containing wheat powder were inoculated with pure cultures of Clostridium acetobutylicum (CAB), Clostridium butyricum (CB), Enterobacter aerogenes (EA), heat-treated anaerobic sludge (ANS) and a mixture of those cultures (MIX). Cumulative hydrogen formation (CHF), hydrogen yield (HY) and specific hydrogen production rate (SHPR) were determined for every culture. The heat-treated anaerobic sludge was found to be the most effective culture with a cumulative hydrogen formation of 560 ml, hydrogen yield of 223 ml H₂ g⁻¹ starch and a specific hydrogen production rate of 32.1 ml H₂ g⁻¹ h⁻¹.     

Direct fermentation of Laminaria japonica for biohydrogen production by anaerobic mixed cultures

A few studies have been made on fermentative hydrogen production from marine algae, despite of their advantages compared with other biomass substrates. In this study, fermentative hydrogen production from Laminaria japonica (one brown algae species) was investigated under mesophilic condition (35 ± 1 °C) without any pretreatment method. A feasibility test was first conducted through a series of batch cultivations, and 0.92 mol H₂/mol hexose_added, or 71.4 ml H₂/g TS of hydrogen yield was achieved at a substrate concentration of 20 g COD/L (based on carbohydrate), initial pH of 7.5, and cultivation pH of 5.5. Continuous operation for a period of 80 days was then carried out using anaerobic sequencing batch reactor (ASBR) with a hydraulic retention time (HRT) of 6 days. After operation for approximately 30 days, a stable hydrogen yield of 0.79 ± 0.03 mol H₂/mol hexose_added was obtained. To optimize bioenergy recovery from L. japonica, an up-flow anaerobic sludge blanket reactor (UASBr) was applied to treat hydrogen fermentation effluent (HFE) for methane production. A maximum methane yield of 309 ± 12 ml CH₄/g COD was achieved during the 90 days operation period, where the organic loading rate (OLR) was 3.5 g COD/L/d.     

Biohydrogen production from crude glycerol by immobilized Klebsiella sp. TR17 in a UASB reactor and bacterial quantification under non-sterile conditions

Biohydrogen production from crude glycerol by immobilized Klebsiella sp. TR17 was investigated in an up-flow anaerobic sludge blanket (UASB) reactor. The reactor was operated under non-sterile conditions at 40^○C and initial pH 8.0 at different hydraulic retention times (HRTs) (2–12 h) and glycerol concentrations (10–30 g/L). Decreasing the HRT led to an increase in hydrogen production rate (HPR) and hydrogen yield (HY). The highest HPR of 242.15 mmol H₂/L/d and HY of 44.27 mmol H₂/g glycerol consumed were achieved at 4 h HRT and glycerol concentrations of 30 and 10 g/L, respectively. The main soluble metabolite was 1,3-propanediol, which implies that Klebsiella sp. was dominant among other microorganisms. Fluorescence in situ hybridization (FISH) revealed that the microbial community was dominated by Klebsiella sp. with 56.96, 59.45, and 63.47% of total DAPI binding cells, at glycerol concentrations of 10, 20, and 30 g/L, respectively.     

Thermophilic biohydrogen production from energy plants by Caldicellulosiruptor saccharolyticus and comparison with related studies

Air-dried samples of sweet sorghum, sugarcane bagasse, wheat straw, maize leaves and silphium were utilized without chemical pretreatment as sole energy and carbon sources for H₂ production by the extreme thermophilic bacterium Caldicellulosiruptor saccharolyticus. The specific H₂ production rates and yields were determined in the batch fermentation process. The best substrate was wheat straw, with H₂ production capacity of 44.7 L H₂ (kg dry biomass)^?1 and H₂ yield of 3.8 mol H₂ (mol glucose)^?1. Enzymatically pretreated maize leaves exhibited H₂ production of 38 L H₂ (kg dry biomass)^?1. Slightly less H₂ was obtained from homogenized whole plants of sweet sorghum. Sweet sorghum juice was an excellent H₂ source. Silphium trifoliatum was also fermented though with a moderate production. The results showed that drying is a good storage method and raw plant biomass can be utilized efficiently for thermophilic H₂ production. The data were critically compared with recently published observations.     

Hydrogen production using sono-biohydrogenator

Hydrogen production in a novel sonicated biological hydrogen reactor (SBHR) was investigated and compared with a continuous stirred tank reactor (CSTR). The two systems were operated at a hydraulic retention time (HRT) of 12 h and two organic loading rates (OLRs) of 21.4 and 32.1 g COD/L.d. The average hydrogen production rates per unit reactor volume for the conventional CSTR were 2.6 and 2.8 L/L.d, as compared with 4.8 and 5.6 L/L.d for SBHR, at the two OLRs, respectively. Hydrogen yields of 1.2 and 1.0 mol H₂/mol glucose were observed for the CSTR, respectively, while for the SBHR, the hydrogen yields were 2.1 and 1.9 mol H₂/mol glucose at the two OLRs, respectively. The hydrogen content in the SBHR’s headspace was higher than that in CSTR by 10% and 31% at OLRs of 21.4 and 32.1 g COD/L.d, respectively. Both glucose conversion efficiency and HAc/HBu ratio in the SBHR were higher than in the conventional CSTR at both OLRs. The biomass yield of about 0.32 g VSS/g COD observed in the CSTR and 0.23 g VSS/g COD in the SBHR substantiate the higher H₂ yield in the SBHR. DGGE analysis confirmed the specificity of the microbial hydrogen-producing culture in the SBHR, with two different hydrogen producers (Clostridium sp. and Citrobacter freundii) detected in the SBHR and not detected in the CSTR.     

A simple method to reduce the start-up period in a H2-producing UASB reactor

Introduction of an up-flow anaerobic sludge blanket (UASB) reactor apparatus to fermentative hydrogen production (FHP) enormously improves H₂ production performance. However, the long start-up period required to form H₂-producing granules (HPG) remains as a major obstacle. In the present work, a completely-stirred tank reactor (CSTR) was operated for 7 days, and the mixed liquor in the CSTR was transferred to a UASB reactor (UASBr (I)) as a seeding source. Coffee drink manufacturing wastewater (CDMW) was used as a feedstock, constituting the first attempt to form HPG from actual industrial wastewater. The strategy employed here was found to be more effective in developing HPG than directly starting from the UASB reactor (UASBr (II)), which is attributed to substantially higher active mass transfer in the CSTR. The average size of particles in the UASBr (II) blanket zone after 50 days of operation corresponded with that in the CSTR after only 7 days of operation. The drastic decrease of extracellular polymeric substance (EPS) protein concentration in the CSTR operation also indicates efficient removal of non-active biomass, the presence of which could adversely affect HPG formation. UASBr (I) showed a stable H₂ yield and H₂ production rate of 1.78 mol H₂/mol hexose_added and 2.76 L H₂/L/h, respectively, and HPG with an average size of 1.9 mm were developed after 45 days. It appears that the abundant presence of divalent ions, especially calcium ions, contained in the CDMW facilitated HPG formation.     

Photofermentive production of biohydrogen from oil palm waste hydrolysate

Oil palm empty fruit bunch (OPEFB) was hydrolyzed with dilute sulfuric acid (6% v/v; 8 mL acid per g dry OPEFB) at 120 °C for 15-min to release the fermentable sugars. The hydrolysate contained xylose (23.51 g/L), acetic acid (2.44 g/L) and glucose (1.80 g/L) as the major carbon components. This hydrolysate was used as the sole carbon source for photofermentive production of hydrogen using a newly identified photosynthetic bacterium Rhodobacter sphaeroides S10. A Plackett–Burman experimental design was used to examine the influence of the following on hydrogen production: yeast extract concentration, molybdenum concentration, magnesium concentration, EDTA concentration and iron concentration. These factors influenced hydrogen production in the following decreasing order: yeast extract concentration > molybdenum concentration > magnesium concentration > EDTA concentration > iron concentration. Under the conditions used (35 °C, 14.6 W/m² illumination, initial pH of 7.0), the optimal composition of the culture medium was (per L): mixed carbon in OPEFB hydrolysate 3.87 g, K₂HPO₄ 0.9 g, KH₂PO₄ 0.6 g, CaCl₂⋅2H₂O 75 mg, l-glutamic acid 795.6 mg, FeSO₄⋅7H₂O 11 mg, Na₂MoO₂⋅2H₂O 1.45 mg, MgSO₄⋅7H₂O 2.46 g, EDTA 0.02 g, yeast extract 0.3 g). With this medium, the lag period of hydrogen production was 7.65 h, the volumetric production rate was 22.4 mL H₂/L medium per hour and the specific hydrogen production rate was 7.0 mL H₂/g (xylose + glucose + acetic acid) per hour during a 90 h batch culture of the bacterium. Under optimal conditions the conversion efficiency of the mixed carbon substrate to hydrogen was nearly 29%.     

Thermophilic hydrogen and methane production from sugarcane stillage in two-stage anaerobic fluidized bed reactors

This study evaluated the feasibility of H₂ and CH₄ production in two-stage thermophilic (55 °C) anaerobic digestion of sugarcane stillage (5,000 to 10,000 mg COD.L⁻¹) using an acidogenic anaerobic fluidized bed reactor (AFBR-A) with a hydraulic retention time (HRT) of 4 h and a methanogenic AFBR (AFBR-S) with HRTs of 24 h–10 h. To compare two-stage digestion with single-stage digestion, a third methanogenic reactor (AFBR-M) with a HRT of 24 h was fed with increasing stillage concentrations (5,000 to 10,000 mg COD.L⁻¹). The AFBR-M produced a methane content of 68.4 ± 7.2%, a maximum yield of 0.30 ± 0.04 L CH₄.g COD⁻¹, a production rate of 3.78 ± 0.40 L CH₄.day⁻¹.L⁻¹ and a COD removal of 73.2 ± 5.0% at an organic loading rate (OLR) of 7.5 kg COD.m⁻³.day⁻¹. In contrast, the two-stage AFBR-A system produced a hydrogen content of 23.9 ± 5.6%, a production rate of 1.30 ± 0.16 L H₂.day⁻¹.L⁻¹ and a yield of 0.34 ± 0.08 mmol H₂.g CODap⁻¹. Additionally, the decrease in the HRT from 18 h to 10 h in the AFBR-S favored a higher methane production, improving the maximum methane content (74.5 ± 6.0%), production rate (5.57 ± 0.38 L CH₄.day⁻¹.L⁻¹) and yield (0.26 ± 0.06 L CH₄.g COD⁻¹) at an OLR of 21.6 kg COD.m⁻³.day⁻¹ (HRT of 10 h) with a total COD removal of 70.1 ± 7.1%. Under the applied COD of 10,000 mg L⁻¹, the two-stage system showed a 52.8% higher energy yield than the single-stage anaerobic digestion system. These results show that, relative to a single-stage system, two-stage anaerobic digestion systems produce more hydrogen and methane while achieving similar treatment efficiencies.     

Co-producing hydrogen and methane from higher-concentration of corn stalk by combining hydrogen fermentation and anaerobic digestion

In this paper, the high concentration of corn stalk (60 g/L) was employed as feedstock to produce bio-hydrogen and methane by combining hydrogen fermentation and anaerobic digestion. In the first stage of hydrogen fermentation, the effects of several key parameters, such as strain enhancement technique, cetyl trimethyl ammonium bromide (CTAB), NH₄HCO₃ on hydrogen production from cornstalk were investigated and optimized. The maximum hydrogen yield of 79.8 ± 1.5 ml H₂/g-TS and hydrogen production rate of 3.78 ml/g-cornstalk h was observed at fixed acidizing cornstalk of 60 g/L, strains Bacillus sp. FS2011 dosage of 10%(v/v), CTAB of 30 mg/L, NH₄HCO₃ of 1.2 g/L and initial pH of 7.5 ± 0.5 at 36 ± 1 °C, respectively. In the second stage of anaerobic digestion, the effluent from hydrogen production bio-reactor was further employed as the feedstock to produce methane by methanogenic bacteria, the maximum methane yield of 227 ± 2.5 ml CH₄/g-COD and COD removal rate of 95  ± 1% was recorded. The interesting observations were that the total amount of the organic wastewater produced in a higher substrate concentration (60 g/l) by hydrogen fermentation was reduced by about two-thirds compared with that of traditional low substrate concentration (≤20 g/l).     

System optimization for effective hydrogen production via anaerobic digestion and biogas steam reforming

To construct a system for the effective hydrogen production from food waste, the conditions of anaerobic digestion and biogas reforming have been investigated and optimized. The type of agitator and reactor shape affect the performance of anaerobic digestion reactors. Reactors with a cubical shape and hydrofoil agitator exhibit high performance due to the enhanced axial flow and turbulence as confirmed by simulation of computational fluid dynamics. The stability of an optimized anaerobic digestion reactor has been tested for 60 days. As a result, 84 L of biogas is produced from 1 kg of food waste. Reaction conditions, such as reaction temperature and steam/methane ratio, affect the biogas steam reforming reaction. The reactant conversions, product yields, and hydrogen production are influenced by reaction conditions. The optimized reaction conditions include a reaction temperature of 700 °C and H₂O/CH₄ ratio of 1.0. Under these conditions, hydrogen can be produced via steam reforming of biogas generated from a two-stage anaerobic digestion reactor for 25 h without significant deactivation and fluctuation.     

Sequential production of hydrogen and methane using hemicellulose hydrolysate from diluted acid pretreatment of sugarcane straw

Sugarcane straw is not effectively used in the industry currently. However, sugarcane straw hemicellulose hydrolyzate (HH) application as raw material for H₂ and CH₄ production is a promising alternative. In this work, the two-stage anaerobic digestion (TS-AD) approach led to 37.86 mL_H2/L.h and 40.12 mL_CH4/L.d, while the single-stage anaerobic digestion (SS-AD) generated 46.11 mL_CH4/L.d. Hence, the two-stage process was energetically favorable than the single-stage by approximately 33%. Additionally, the comparison with standard medium (composed of glucose, xylose, and arabinose) applied as raw material indicated that although hydroxymethylfurfural and furfural from HH were not responsible for the decrease in H₂ production, they extended the adaptive phase of methanogenic archaea during the methanogenesis. Hemicellulose hydrolysate is an attractive raw material for two-stage anaerobic digestion.