Synthetic CaO-based sorbent for high-temperature CO2 capture in sorption-enhanced hydrogen production

Calcium precursor and surfactant addition on properties of synthetic alumina-containing CaO-based for CO₂ capture and for sorption-enhanced steam methane reforming process (SE-SMR) were investigated. Results showed that the sorbent derived from calcium d-gluconic acid (CG-AN) offered CO₂ sorption capacity of 0.38 g CO₂/g sorbent, which is greater than 0.17 g CO₂/g sorbent of the sorbent derived from calcium nitrate (CN-AN). Addition of CTAB surfactant during synthesis was found to enhance CO₂ sorption capacity for CG-AN but not for CN-AN sorbents. Stability tests of the modified sorbents for 10 cycles showed that CG-AN-CTAB provided higher CO₂ sorption capacity than CN-AN-CTAB for each corresponding cycle. Incorporation of CG-AN with Ni catalyst (Ni-CG-AN) using wet-mixing technique offered the longest pre-breakthrough period of 60 min for average maximum H₂ purity of 88% at 600 °C and a steam/methane molar ratio of 3.     

Experimental investigation of improved calcium-based CO2 sorbent and Co3O4/SiO2 oxygen carrier for clean production of hydrogen in sorption-enhanced chemical looping reforming

In this study, highly pure hydrogen is produced in sorption enhanced chemical looping steam methane reforming (SE-CLSMR) using cobalt-based oxygen carrier (OC) and cerium promoted CaO-based sorbent. In addition, the CO₂ removal from a gas stream at high temperatures is investigated via calcium looping process prior to SE-CLSMR process. The prepared samples are characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) and energy dispersive X-ray spectroscopy (EDX) techniques. The effect of Ca/Ce molar ratio (100/0.00–0.91/0.09), sorption temperature (550–650 °C) and sorbent lifetime are studied to find the optimal sorbent. The characterization results show the uniform and orderly CeO₂ dispersed sorbent nanoparticles that notably improved the sorbent morphology compared with blank CaO. The sorption results revealed the negative effect of temperature on CO₂ uptake of all the samples. In addition, the CO₂ sorption evaluations indicate that the molar ratio of cerium to calcium plays a significant role in the stability of sorbent and improved the CO₂ sorption capacity significantly. The high CO₂ removal efficiency in the cerium modified sorbents could be due to decrease in diffusion resistance of CO₂ through the sorbent structure during the carbonation reaction. Furthermore, results show that the addition of cerium to the sorbent structure, effectively improves the thermal resistance of synthesis sorbents. The SE-CLSMR results showed that the H₂ purity could be increased up to about 95% considering Co₃O₄/SiO₂ oxygen carrier and cerium promoted calcium-based sorbent at relatively low temperature of 550 °C, which is comparable with 84% in CLR process.     

Sorbent enhanced hydrogen production from steam gasification of coal integrated with CO2 capture

In this work, CO₂ capture and H₂ production during the steam gasification of coal integrated with CO₂ capture sorbent were investigated using a horizontal fixed bed reactor at atmospheric pressure. Four different temperatures (650, 675, 700, and 750 °C) and three sorbent-to-carbon ratios ([Ca]/[C] = 0, 1, 2) were studied. In the absence of sorbent, the maximum molar fraction of H₂ (64.6%) and conversion of coal (71.3%) were exhibited at the highest temperature (750 °C). The experimental results verified that the presence of sorbent in the steam gasification of coal enhanced the molar fraction of H₂ to more than 80%, with almost all CO₂ was fixed into the sorbent structure, and carbon monoxide (CO) was converted to H₂ and CO₂ through the water gas shift reaction. The steam gasification of coal integrated with CO₂ capture largely depended on the reaction temperature and exhibited optimal conditions at 675 °C. The maximum molar fraction of H₂ (81.7%) and minimum CO₂ concentration (almost 0%) were obtained at 675 °C and a sorbent-to-carbon ratio of 2.     

Refuse derived fuel hydrogasification coupled with methane steam reforming

The hydrogasification of Refuse Derived Fuel (RDF) consisting of non-recyclable plastic polymers was combined with methane steam reforming in a “hydrogen self-sustained” loop configuration. The hydrogasification unit fed by 1000 kg/h of RDF was initially modeled by Aspen plus to define best operating conditions, namely temperature, pressure and hydrogen feed flow rate. After the simulations, the temperature of the hydrogasification process has been fixed at 300 °C, the pressure at 10 bar and the hydrogen feed flow rate at 140 kg/h. The steam reforming unit operates at 850 °C while the water-gas shift is conducted at 350 °C. When all the methane produced by hydrogasification is used to feed the steam reformer, which yields H₂ that is recycled back to the hydrogasifier, the net hydrogen production is 222 kg/h with an amount of CO₂ released of 2265 kg/h. For the different process configurations adopted, the energy efficiency of the process ranges 84–89%.     

One step methane production based on catalytic pressurized calcium looping gasification with in-situ CO2 capture and self-sustained heat supply

Catalytic steam hydrogasification of coal is a direct method for methane production. Calcium looping concept is usually used in coal gasification process for in-situ carbon dioxide removal and heat supply. In this paper, a new process combining catalytic steam hydrogasification and calcium looping was proposed and investigated using a self designed instantaneously feeding reactor under high-temperature and pressurized conditions. The effects of operation conditions (including hydrogen concentration with a range of 0–50 vol%, gasification pressure with a range of 0.1–3.5 MPa, gasification temperature with a range of 700–800 °C, and gasification-calcination cycle number up to six) on the performance of the new process have been studied. The results show that: (i) increasing H₂ concentration is beneficial to methane products; (ii) high temperature and low pressure are not conducive to methane production and carbon dioxide capture as well as the self-sustained heat supply in gasifier; (iii) the methane content and carbon conversion can be maintained at 30–40 vol% and 75–80% for the durability tests. According to the performance of gas products, 750 °C 3.5 MPa and Ca/C = 0.5 are suggested for the new process. In addition, the gasification reactivity can be affected by the Ca–K-Char interaction as indicated by the XRD, FT-IR and SEM-EDX analysis.     

Conversion of carbon dioxide and methane in biomass synthesis gas for liquid fuels production

The premise of this research is to find whether methane (CH₄) and carbon dioxide (CO₂) produced during biomass gasification can be converted to carbon monoxide (CO) and hydrogen (H₂). Simultaneous steam and dry reforming was conducted by selecting three process parameters (temperature, CO₂:CH₄, and CH₄:steam ratios). Experiments were carried out at three levels of temperature (800 °C, 825 °C and 850 °C), CO₂:CH₄ ratio (2:1, 1:1 and 1:2), and CH₄:steam ratio (1:1, 1:2 and 1:3) at a residence time of 3.5 × 10³ g_cat min/cc using a custom mixed gas that resembles biomass synthesis gas, over a commercial catalyst. Experiments were conducted using a Box-Behnken approach to evaluate the effect of the process variables. The average CO and CO₂ selectivities were 68% and 18%, respectively, while the CH₄ and CO₂ conversions were about 65% and 48%, respectively. The results showed optimum conditions for maximum CH₄ conversion was at 800 °C, CO₂:CH₄ ratio and CH₄:steam ratios of 1:1.     

A novel catalyst–sorbent system for an efficient H2 production with in-situ CO2 capture

This paper presents an experimental investigation for an improved process of sorption-enhanced steam reforming of methane in an admixture fixed bed reactor. A highly active Rh/Ce_αZr_1−αO₂ catalyst and K₂CO₃-promoted hydrotalcite are utilized as novel catalyst/sorbent materials for an efficient H₂ production with in situ CO₂ capture at low temperature (450–500 °C). The process performance is demonstrated in response to temperature (400–500 °C), pressure (1.5–6.0 bar), and steam/carbon ratio (3–6). Thus, direct production of high H₂ purity and fuel conversion >99% is achieved with low level of carbon oxides impurities (<100 ppm). A maximum enhancement of 162% in CH₄ conversion is obtained at a temperature of 450 °C and a pressure of 6 bar using a steam/carbon molar ratio of 4. The high catalyst activity of Rh yields an enhanced CH₄ conversion using much lower catalyst/sorbent bed composition and much smaller reactor size than Ni-based sorption enhanced processes at low temperature. The cyclic stability of the process is demonstrated over a series of 30 sorption/desorption cycles. The sorbent exhibited a stable performance in terms of the CO₂ working sorption capacity and the corresponding CH₄ conversion obtained in the sorption enhanced process. The process showed a good thermal stability in the temperature range of 400–500 °C. The effects of the sorbent regeneration time and the purge stream humidity on the achieved CH₄ conversion are also studied. Using steam purge is beneficial for high degree of CO₂ recovery from the sorbent.     

Thermodynamic equilibrium analysis of combined carbon dioxide reforming with steam reforming of methane to synthesis gas

Thermodynamics equilibrium analysis of carbon dioxide reforming of methane combined with steam reforming to synthesis gas was studied by Gibbs free energy minimization method to understand the effects of process variables such as temperature, pressure and inlet CH₄/H₂O/CO₂ ratios on product distributions. For this purpose, the calculations were carried out at total pressures of 1 and 20 bar, and at ranges of temperature and steam-to-carbon ratios of 200–1200 °C and 0–0.50, respectively. The results revealed that carbon dioxide reforming of methane combined with steam reforming process was controlled by different reactions with regard to the operating temperature, pressure and varying feed compositions. The H₂/CO product ratio could be modified by changing the relative concentration of steam and CO₂ in the feed, temperature and pressure, depending on the downstream application.     

Enhanced coal gasification heated by unmixed combustion integrated with an hybrid system of SOFC/GT

For clean utilization of coal, enhanced gasification by in situ CO₂ capture has the advantage that hydrogen production efficiency is increased while no energy is required for CO₂ separation. The unmixed fuel process uses a sorbent material as CO₂ carrier and consists of three coupled reactors: a coal gasifier where CO₂ is captured generating a H₂-rich gas that can be utilized in fuel cells, a sorbent regenerator where CO₂ is released by sorbent calcination and it is ready for capture and a reactor to oxidize the oxygen transfer material which produces a high temperature/pressure vitiated air. This technology has the potential to eliminate the need for the air separation unit using an oxygen transfer material. Reactors' temperatures range from 750 °C to 1550 °C and the process operates at pressure around 7.0 bar. This paper presents a global thermodynamic model of the fuel processing concept for hydrogen production and CO₂ capture combined with fuel and residual heat usage. Hydrogen is directly fed to a solid oxide fuel cell and exhaust streams are used in a gas turbine expander and in a heat recovery steam generator. This paper analyzes the influence of steam to carbon ratio in gasifier and regeneration reactor, pressure of the system, temperature for oxygen transfer material oxidation, purge percentage in calciner, average sorbent activity and oxidant utilization in fuel cell. Electrical efficiency up to 73% is reached under optimal conditions and CO₂ capture efficiencies near 96% ensure a good performance for GHG's climate change mitigation targets.     

Continuous sorption-enhanced steam reforming of glycerol to high-purity hydrogen production

In this study, the continuous sorption-enhanced steam reforming of glycerol to high-purity hydrogen production by a simultaneous flow concept of catalyst and sorbent for reaction and regeneration using two moving-bed reactors has been evaluated experimentally. A Ni-based catalyst (NiO/NiAl₂O₄) and a lime sorbent (CaO) were used for glycerol steam reforming with and without in-situ CO₂ removal at 500 °C and 600 °C. The simultaneous regeneration of catalyst and sorbent was carried out with the mixture gas of N₂ and steam at 900 °C. The product gases were measured by a GC gas analyzer. It is obvious that the amounts of CO₂, CO and CH₄ were reduced in the sorption-enhanced steam reforming of glycerol, and the H₂ concentration is greatly increased in the pre-CO₂ breakthrough periods within 10 min both 500 °C and 600 °C. The extended time of operation for high-purity hydrogen production and CO₂ capture was obtained by the continuous sorption-enhanced steam reforming of glycerol. High-purity H₂ products of 93.9% and 96.1% were produced at 500 °C and 600 °C and very small amounts of CO₂, CH₄ and CO were formed. The decay in activity during the continuous reaction-regeneration of catalyst and sorbent was not observed.     

Production of high purity hydrogen by sorption enhanced steam reforming of crude glycerol

Here we report effective production of pure hydrogen from crude glycerol by the one-stage sorption enhanced steam reforming (SESR) process. This process yielded H₂ up to 88% with a very high purity (99.7 vol%) at atmospheric pressure and at 550–600 °C with a steam/C = 3 in a fixed-bed reactor over a mixture of Ni/Co catalyst derived from hydrotalcite-like material (HT) and dolomite as CO₂ sorbent. The concentration of methane is lowest at 575 °C, while the CO concentration increases concurrently with increasing temperature from 525 to 600 °C. The high coking potential of glycerol and fatty acid methyl esters (C₁₇–C₁₉) resulted in the increased formation of coke, thus lower hydrogen yield. The reaction rates of methane reforming and water–gas shift reactions are much higher than the steam reforming of crude glycerol on Co–Ni catalysts. The high purity of hydrogen can be obtained even at low spatial times with low crude glycerol conversions. Our work reveals a great potential to directly convert biomass derived complex mixtures to the most clean energy carrier of hydrogen with high yield and purity.     

Tri-reforming of methane over Ni@SiO2 catalyst

A nickel-silica core@shell catalyst was applied for a methane tri-reforming process in a fixed-bed reactor. To determine the optimal condition of the tri-reforming process for production of syngas appropriate for methanol synthesis the effect of reaction temperature (550–750 °C), CH₄:H₂O molar ratio (1:0–3.0) and CH₄:O₂ molar ratio (1:0–0.5) in the feedstock was investigated. CH₄ conversion rate and H₂/CO ratio in the produced syngas were influenced by the feedstock composition. Increasing the amount of steam above the proportion of CH₄:H₂O 1:0.5 reduced the H₂:CO molar ratio in produced syngas to ∼1.5. Increasing oxygen partial pressure improved methane conversion to 90% at 750 °C. At low ∼550 °C reaction temperature the tri-reforming process was not effective with low hydrogen production (H₂ yield ∼20%) and very low <5% CO₂ conversion. Increasing reaction temperature increased hydrogen yield to ∼85% at 750 °C. From all the tested reaction conditions the optimal for tri-reforming over the 11%Ni@SiO₂ catalyst was: feed composition with molar ratio CH₄:CO₂:H₂O:O₂:He 1:0.5:0.5:0.1:0.4 at T = 750 °C. The results were explained in the context of characterisation of the catalysts used. The obtained results showed that the tri-reforming process can be applied for production of syngas with composition suitable for methanol synthesis.     

In-situ CO2 capture in a pilot-scale fluidized-bed membrane reformer for ultra-pure hydrogen production

A novel pilot fluidized-bed membrane reformer (FBMR) with permselective palladium membranes was operated with a limestone sorbent to remove CO₂in-situ, thereby shifting the thermodynamic equilibrium to enhance pure hydrogen production. The reactor was fed with methane to fluidize a mixture of calcium oxide (CaO)/limestone (CaCO₃) and a Ni-alumina catalyst. Experimental tests investigated the influence of limestone loading, total membrane area and natural gas feed rates. Hydrogen-permeate to feed methane molar ratios in excess of 1.9 were measured. This value could increase further if additional membrane area were installed or by purifying the reformer off-gas given its high hydrogen content, especially during the carbonation stages. A maximum of 0.19 mol of CO₂ were adsorbed per mole of CaO during carbonation. For the conditions studied, the maximum carbon capture efficiency was 87%. The reformer operated for up to 30 min without releasing CO₂ and for up to 240 min with some degree of CO₂ capture. It was demonstrated that CO₂ adsorption can significantly improve the productivity of the reforming process. In-situ CO₂ capture enhanced the production of hydrogen whose purity exceeded 99.99%.     

Enhanced hydrogen-rich gas production from steam gasification of coal in a pressurized fluidized bed with CaO as a CO2 sorbent

Steam gasification of a typical Chinese bituminous coal for hydrogen production in a lab-scale pressurized bubbling fluidized bed with CaO as CO₂ sorbent was performed over a pressure range of ambient pressure to 4 bar. The compositions of the product gases were analyzed and correlated to the gasification operating variables that affecting H₂ production, such as pressure (P), mole ratio of steam to carbon ([H₂O]/[C]), mole ratio of CaO to carbon ([CaO]/[C]) and temperature (T). The experimental results indicated that the H₂ concentration was enhanced by raising the temperature, pressure and [H₂O]/[C] under the circumstances we observed. With the presence of CaO sorbent, CO₂ in the production gas was absorbed and converted to solid CaCO₃, thus shifting the steam reforming of hydrocarbons and water gas shift reaction beyond the equilibrium restrictions and enhancing the H₂ concentration. H₂ concentration was up to 78 vol% (dry basis) under a condition of 750 °C, 4 bar, [Ca]/[C] = 1 and [H₂O]/[C] = 2, while CO₂ (2.7 vol%) was almost in-situ captured by the CaO sorbent. This study demonstrated that CaO could be used as a substantially excellent CO₂ sorbent for the pressurized steam gasification of bituminous coal. For the gasification process with the presence of CaO, H₂-rich syngas was yielded at far lower temperatures and pressures in comparison to the commercialized coal gasification technologies. SEM/EDX and gas sorption analyses of solid residues sampled after the gasification showed that the pore structure of the sorbent was recovered after the steam gasification process, which was attributed to the formation of Ca(OH)₂. Additionally, a coal-CaO–H₂O system was simulated with using Aspen Plus software. Calculation results showed that higher temperatures and pressures favor the H₂ production within a certain range.     

Hydrogen rich fuel gas production by gasification of wet biomass using a CO2 sorbent

Hydrogen rich fuel gas production by gasification of wet biomass accompanied by CO₂ absorption is proposed. The paper addressed this topic, and experiments were conducted to investigate the effects of the moisture content (M), the molar ratio of Ca(OH)₂ to carbon in the biomass ([Ca]/[C]) and the reactor temperature (T) on hydrogen production and CO₂ absorption by CaO. Measurement of the calcium compounds in solid residues was carried out with XRD and SEM. The results show that directly gasifying of wet biomass not only favors hydrogen production but also promotes CO₂ absorption by CaO. For the experiment with wet biomass (M = 0.90), the H₂ yield is increased by 51.5% while the CO₂ content is decreased by 28.4% than that for experiments with dry biomass (M = 0.09). CaO plays the dual role of catalyst and sorbent. It is noteworthy that CaO reveals a stronger effect on the water gas shift reaction than on the steam reforming of methane. The increase of the reactor temperature contributes to produce more H₂, but goes against CO₂ absorption by CaO. XRD spectrum and SEM image of the solid residues further confirmed that high temperature is unfavorable to CO₂ absorption by CaO. For the new method, the optimal operating temperature is in the 923–973 K range.     

Integrated catalytic adsorption (ICA) steam gasification system for enhanced hydrogen production using palm kernel shell

This paper investigates the integrated catalytic adsorption (ICA) steam gasification of palm kernel shell for hydrogen rich gas production using pilot scale fluidized bed gasifier under atmospheric condition. The effect of temperature (600–750 °C) and steam to biomass ratio (1.5–2.5 wt/wt) on hydrogen (H₂) yield, product gas composition, gas yield, char yield, gasification and carbon conversion efficiency, and lower heating values are studied. The results show that H₂ hydrogen composition of 82.11 vol% is achieved at temperature of 675 °C, and negligible carbon dioxide (CO₂) composition is observed at 600 °C and 675 °C at a constant steam to biomass ratio of 2.0 wt/wt. In addition, maximum H₂ yield of 150 g/kg biomass is observed at 750 °C and at steam to biomass ratio of 2.0 wt/wt. A good heating value of product gas which is 14.37 MJ/Nm³ is obtained at 600 °C and steam to biomass ratio of 2.0 wt/wt. Temperature and steam to biomass ratio both enhanced H₂ yield but temperature is the most influential factor. Utilization of adsorbent and catalyst produced higher H₂ composition, yield and gas heating values as demonstrated by biomass catalytic steam gasification and steam gasification with in situ CO₂ adsorbent.     

Simulation of steam reforming of biogas in an industrial reformer for hydrogen production

The paper aims to investigate the steam reforming of biogas in an industrial-scale reformer for hydrogen production. A non-isothermal one dimensional reactor model has been constituted by using mass, momentum and energy balances. The model equations have been solved using MATLAB software. The developed model has been validated with the available modeling studies on industrial steam reforming of methane as well as with the those on lab-scale steam reforming of biogas. It demonstrates excellent agreement with them. Effect of change in biogas compositions on the performance of industrial steam reformer has been investigated in terms of methane conversion, yields of hydrogen and carbon monoxide, product gas compositions, reactor temperature and total pressure. For this, compositions of biogas (CH₄/CO₂ = 40/60 to 80/20), S/C ratio, reformer feed temperature and heat flux have been varied. Preferable feed conditions to the reformer are total molar feed rate of 21 kmol/h, steam to methane ratio of 4.0, temperature of 973 K and pressure of 25 bar. Under these conditions, industrial reformer fed with biogas, provides methane conversion (93.08–85.65%) and hydrogen yield (1.02–2.28), that are close to thermodynamic equilibrium condition.     

Design and comparisons of three biomass based hydrogen generation systems with chemical looping process

The technology of hydrogen generation from biomass has attracted more and more attentions nowadays. In this work, three biomass-based chemical looping hydrogen generation systems, Systems A, B and C, are comprehensively studied. System A is mainly composed of biomass hydrogasification, methane reformation and the calcium-looping based CO₂ absorption. System B is mainly composed of biomass steam gasification and Fe₂O₃/FeO-looping based hydrogen generation circulation. System C is mainly composed of biomass steam gasification and Fe₃O₄/FeO-looping based hydrogen generation circulation. The three systems are modeled and their characteristics are analyzed and compared thermodynamically. System A has the highest cold gas efficiency (CGE) which is 72%; System B has the lowest CGE of 54% but it can generate additional nitrogen as byproduct; System C has the highest hydrogen generation ratio and its CGE is moderate and is 60%. The carbon dioxide sequestration rates of the three systems are all above 90%.     

Integrated adsorption steam gasification for enhanced hydrogen production from palm waste at bench scale plant

The generation of hydrogen-enriched synthesis gas from catalytic steam gasification of biomass with in-situ CO₂ capture utilizing CaO has a high perspective as clean energy fuels. The present study focused on the process modeling of catalytic steam gasification of biomass using palm empty fruit bunch (EFB) as biomass for hydrogen generation through experimental work. Experiment work has been carried out using a fluidized bed gasifier on a bench-scale plant. The established model integrates the kinetics of EFB catalytic steam gasification reactions, in-situ capturing of CO₂, mass and energy balance calculations. Chemical reaction constants have been calculated via the parameters fitting optimization approach. The influence of operating parameters, mainly temperature, steam to biomass, and sorbent to biomass ratio, was investigated for the hydrogen purity and yield through the experimental study and developed model. The results predicted approximately 75 vol% of the hydrogen purity in the product gas composition. The maximum H₂ yield produced from the gasifier was 127 gH₂/kg of EFB via experimental setup. The increase in both steam to biomass ratio and temperature enhanced the production of hydrogen gas. Comparing the results with already published literature showed that the current system enables to produce a high amount of hydrogen from EFB.     

High hydrogen yield and purity from palm empty fruit bunch and pine pyrolysis oils

The benefits of CO₂ sorption enhanced steam reforming using calcined dolomite were demonstrated for the production of hydrogen from highly oxygenated pyrolysis oils of the agricultural waste palm empty fruit bunches (PEFB) and pine wood. At 1 atm in a down-flow packed bed reactor at 600 °C, the best molar steam to carbon ratios were between 2 and 3 using a Ni catalyst. After incorporating steam-activated calcined dolomite as the CO₂ sorbent in the reactor bed, the H₂ yield from the moisture free PEFB oil increased from 9.5 to 10.4 wt.% while that of the pine oil increased from 9.9 to 13.9 wt.%. The hydrogen purity also rose from 68 to 96% and from 54 to 87% for the PEFB and pine oils respectively, demonstrating very substantial sorption enhancement effects.