Ozone Generation by Hybrid Discharge Combined with Catalysis

In this paper, combining hybrid discharge with pellet alumina catalyst is used for ozone generation. The hybrid discharge including corona discharge (CD), surface discharge (SD) and dielectric barrier discharge (DBD) may happen in the device. Factors that affect the ozone production efficiency and concentration are studied, such as energy density, power, gas flow rate, frequency, peak voltage and catalysts.     

Productivity and Efficiency of Ozone Synthesis in Coplanar Discharge Arrangements

In order determine the potential of coplanar discharge arrangements with short electrode distances for the production of ozone, a numerical model of the discharge behavior has been developed. The temporal and spatial distributions of the discharge parameters e.g. those of the field strength, the densities of the charged particles in the gas region and on the dielectric surface and that of the energy release reveal that the ozone production results from the electron phase of the discharge. Quantitative data of the productivity and efficiency of the ozone yield in a certain system are presented, which are in agreement with experimental results.     

Simulation of Ozone Synthesis in Oxygen- and Air-Fed Surface Discharge Arrangements

Surface discharge (SD) arrangements are used in commercial ozone generators like conventional arrangements with a gas gap. While in oxygen the characteristics of the ozone production are comparable in both arrangements, the efficiency of ozone production from air is significant lower in SDs. From experimental results it is believed that high temperatures in the discharge cause this “poisoning” of air-fed SD ozone generators. To clarify this, the ozone synthesis from air near atmospheric pressure is investigated with the help of a two-dimensional self-consistent modeling of the discharge development and the relevant plasma-chemical reactions. The temperature in the discharge area is determined from energy densities of electrons and ions and included in the relevant chemical reaction system. The results show a significant temperature increase in front of the metallic surface electrodes combined with an increased concentration of nitrogen oxides.     

Comparative Experimental Study between Surface and Volume DBD Ozone Generator

Volume Dielectric Barrier Discharge (DBD) is nowadays considered the most effective way for ozone generation in the industry. Some papers were published only on surface discharge reactors applied for ozone generation. This article describes an experimental investigation for the comparison between these two reactor types of ozone generation. Two surface and volume DBD reactors of cylindrical shape were used in the same experimental conditions. Obtained results showed that although the majority of ozone generators are of volume discharge type, the surface DBD presents significant superiority in terms of ozone generation and energy efficiency.     

Ozone Generator with Cylindrical Type of Rotating Electrode

An ozone generator using a rotating electrode to improve ozone generation efficiency is proposed. The ozone generator electrode unit consists of a rotating electrode and fixed electrode. The rotating electrode has the grounded 36 pieces of tungsten wires fixed in parallel to the rotation axis on the rotating cylinder surface. A dielectric electrode is used as a fixed electrode located on the inside of the tube of the electrode unit. The width of the apparent discharge gap is 1mm. Alternating current with a frequency of 50 Hz is applied to the electrode unit. The rotation speed can be adjusted from 0 rpm to 1200 rpm by a variable speed motor. Oxygen gas is used as the material gas. Higher ozone concentration and higher ozone generation efficiency are obtained compared with that when the rotation speed is 0 rpm. The gas temperature is measured at the inlet and outlet of the ozone generator, and the rotation speed for the cooling effect is most effective at about 500 rpm. The maximum generation efficiency is estimated to be 61 g/kWh at 800 rpm, and this value is twice as large as in the case of 0 rpm.     

Ozone Generation Using Plate Rotating Electrode Ozonizer- Effect Of Electrode Rotation And Discharge Analysis Method

An attempt to explain the phenomenon of the effect of electrode rotation on the ozone generation process is presented. A discharge photography method was applied and computer analysis method was used to find discharge differences between electrode rotational and non-rotational cases. The research presented shows that with electrode rotation the discharge was more uniform and the ozone generation efficiency increased about 15% compared to an ozonizer with a non-rotating electrode. In addition, during the research, the most suitable electrode rotational speed for the ozone generation process was estimated.     

Basic Parameters of Coplanar Discharge Ozone Generator

Coplanar discharge is a new type of barrier discharge, and has some advantages for high-concentration ozone generation. In this article, basic parameters of coplanar discharge are clarified by experimental and theoretical approaches. Coplanar electrodes consist of many pairs of line electrodes printed on a glass plane, and are covered with dielectric layer. The discharge properties, ozone diffusion process, and surface reaction are discussed. Finally, the scaling rule of a coplanar discharge ozone generator is demonstrated by fabrication of a 3 kg/h ozone generator.     

Optimizing Factors on High Concentration of Ozone Production with Dielectric Barrier Discharge

The gap distance, electrode material, voltage and gas flow velocity were optimized with gas pressure variation of dielectric barrier discharge (DBD) for producing high concentration of ozone. There exists an optimum gas pressure at which the highest ozone concentration is produced with other parameters being fixed. This optimum gas pressure value changes accordingly as the other parameters changed. As the discharge continues at the optimum pressure, the ozone concentration could increase or decrease slowly. This aging effect has different characteristics with the metal electrode material and the impurity level of the oxygen gas used for ozone generation. The aging effect is supposed to be related with the catalytic effect of metal oxide, which is generated in the discharge zone. The change in the characteristic of optimum pressure by the other parameters, indicate that the ozone concentration is deeply related with the filament self-organization characteristics of DBD. At the final optimized condition, the ozone concentration was higher than 22.5 wt.%.     

The Benefits of Small Quantities of Nitrogen in the Oxygen Feed to Ozone Generators

This paper reports the ozone generation in pulsed multichannel dielectric barrier discharge. The influence of nitrogen addition (0.1%–10%) on ozone concentration and ozone generation efficiency in nitrogen–oxygen gas mixtures is studied. Results show that adding 0.1% N₂ would not seriously increase the ozone production. Meanwhile, 1% N₂ content exhibits the highest ozone production efficiency in low SIE (J/L, defined as the ratio of power to gas flow rate) region (0–200 J/L) while adding 0.3% N₂ would lead to the highest ozone generation efficiency in high SIE region (300–800 J/L). The increase of ozone production induced by N₂ addition is more significant in low SIE region compared with that in high SIE region. At 100 J/L, ozone production efficiency increases 26.9% to 201.6 g/kWh with 1% N₂ addition when compared with that in oxygen. At 18 J/L, the observed maximum ozone generation efficiency reaches 252 g/kWh at 1.3 g/Nm³ with 1% N₂ addition. An increase of ozone production can be obtained with 0.3%–2% N₂ addition in all explored SIE ranges.     

Influence of Field Strength and Energy Distribution of Different Barrier Discharge Arrangements on Ozone Generation

Because of different field strength and energy density distributions in volume (VD), surface (SD) and coplanar discharge (CD) arrangements the ozone yield will differ in general. While in VD configurations the initial field strength distribution is rather uniform, the situation is quite different in CD and especially SD devices. The distributions change during discharge development as well as the energy density in the discharge region and by this the ozone yields. The situation in SD arrangements is discussed in detail and is compared with those in VD and CD configurations.     

Ozone Production in a Dielectric Barrier Discharge with Ultrasonic Irradiation

Ozone production has been investigated using an atmospheric pressure dielectric barrier discharge in pure O₂ at room temperature with and without ultrasonic irradiation. It was driven at a frequency of either 15 kHz or ～40 kHz. The ozone production was highly dependent on the O₂ flow rate and the discharge power. Furthermore, powerful ultrasonic irradiation at a fundamental frequency of ～30 kHz with the sound pressure level of ～150 dB into the discharge can improve the ozone production efficiency, particularly when operated at the frequency of 15 kHz at the flow rate of 15 L/min.     

Effect of Silica Packing on Ozone Synthesis from Oxygen-Nitrogen Mixtures

The effect of silica packing in an ozone generator fed with oxygen-nitrogen mixtures has been studied. The measurements were carried out in an ozone generator with a double-sided cooled discharge gap, in which silica packing has been placed. In the presence of the packing considerably higher ozone concentrations were achieved than in the ozone generator without packing. An especially clear effect of silica packing was observed in air-fed conditions. It has been found that the increase in the concentration of the obtained ozone coincides with the increase of N₂O in the post-reaction gas.     

Kinetic Modeling of Ozone Generation via Dielectric Barrier Discharges

A mathematical model combining chemical kinetic and reactor geometry is developed for ozone synthesis in dry O₂ streams with a wire-tube dielectric barrier discharge (DBD) reactor. Good agreement is found between the predicted ozone concentrations and experimental data. Sensitivity analysis is conducted to elucidate the relative importance of individual reactions. Results indicate that the ground-state oxygen atom is the most important species for O₃ generation; however, ozone generation will be inhibited if the O atom is overdosed. The excited species, that is, O(¹ D) and O₂(b ¹Σ), can decompose O₃ and suppress ozone synthesis. The model developed is then applied to modify the original DBD reactor design for the enhancement of ozone yield. With a thinner dielectric thickness, more than 10% increase of ozone concentration is achieved.     

Experimental Study of Ozone Generation by Negative Corona Discharge in Mixtures of N2 and O2

Ozone generation by negative DC corona discharge in N₂-O₂ mixtures has been experimentally investigated using a coaxial wire-cylinder corona reactor operating at room temperature and atmospheric pressure. The experiments have been carried out under different gas flows (15 cm³ min^?1 to 200 cm³ min^?1) and gas compositions (5% to 90% of O₂), and the effect of these parameters on the corona current, the ozone density and the efficiency of the ozone generator have been analyzed. The global rate coefficients for ozone formation and destruction have also been evaluated, and their values compared with those reported by other authors. The maximum efficiency for ozone production was found in gas mixtures with oxygen content about 70–80%.     

A Study of Ozone Synthesis in Coaxial Cylinder Pulse Streamer Corona Discharge Reactors

Synthesis of ozone in coaxial cylinder non-thermal plasma reactors with different structures was investigated in this paper. With digital measuring technology, the absorption energy of non-thermal plasma reactors induced by pulse streamer corona was estimated. In the view of energy absorption of non-thermal plasma reactors, pulse input energy depended on reactor structures, as well as pulse parameters, such as pulse amplitude and DC bias. With coaxial cylinder reactors energized by pulse voltage, the influences on ozone generation of pulse voltage polarity, pulse amplitude, and pulse repetition rate were studied. It was found that positive pulse voltage induced higher ozone generation than negative pulse voltage and higher amplitude pulses generated more ozone. Increasing the pulse repetition rate at a low level increased ozone generation to some extent, but then leveled off with further increasing. A critical repetition rate was found at which the ozone synthesis was the most efficient. Lower pulse amplitude was associated with higher critical repetition rate. Superimposing DC bias on pulse voltage was an effective method to enhance ozone generation. Besides, discharge modes and electrode structures of reactors affect ozone generation. A mixed discharge mode of volume and surface discharges was the most effective mode to generate ozone in all of the experimental discharge modes, namely volume, surface, volume and surface mixed discharge modes. Moreover, helix-cylinder reactors were better than wire-to-cylinder reactors in generating ozone.     

Ozone and Nitrogen Oxides Generation in Gas Flow Enhanced Hollow Needle to Plate Discharge In Air

Siemens made the first ozone generation system by corona discharge about hundred and fifty years ago. At present mainly two types of atmospheric pressure electrical discharges - corona discharge and dielectric barrier discharge are used for production of ozone. Another type of discharge, which can be used for this purpose, is multineedle to plate electrical discharge enhanced by the gas flow. Contrary to the conventional arrangement when the gas is flowing around the needles we studied the discharge in which the gas was pumped through the needles. Results of studies of ozone and nitrogen oxides production by DC electrical discharge in air at atmospheric pressure with a single hollow needle to plate electrode configuration enhanced by the flow of air through the needle for both polarities of the needle, different airflow rates and currents are presented in this paper.     

Ozone Generation from Oxygen and Air: Discharge Physics and Reaction Mechanisms

Industrial ozone generation uses a special high pressure, low temperature electrical discharge which is referred to as the dielectric barrier discharge or silent discharge. The filamentary structure of this discharge and the properties of individual microdischarges are discussed. The main reaction paths for the excited atomic and molecular species in oxygen and air are identified. Possible approaches to obtain high power densities, high ozone generating efficiencies or high ozone concentrations are discussed.     

High Frequency Testing and Modeling of Silent Discharge Ozone Generators

This paper deals with high frequency modeling of silent discharge ozone generators (OGs). The electrical characteristics of two simple silent discharge OGs operated at low and high frequency are analyzed and compared. An equivalent electric model is proposed for the operation of the OG at high frequency. This model can be used to optimize the electronic power converter used to supply silent discharge OGs at high frequency. Experimental results measured in the laboratory for two particular OGs are presented to validate the proposed model.     

Ozone Generation in Air by a DC-Excited Multi-Pin-to-Plane Plasma Source

In the fields of material processing and environmental technology, atmospheric pressure non-thermal plasmas embrace a broad range of applications. Ozone generation is one of them. This paper discusses a DC-excited atmospheric pressure glow discharge in a multi-pin-to-plane electrode configuration for the production of ozone in air. The influence of discharge current, temperature, flow rate and air humidity is investigated. A simple model is proposed to predict the experimental results for the ozone production and ozone concentrations.     

Generation of Radicals using Discharge inside Bubbles in Water for Water Treatment

A new method for a water treatment utilizing radicals produced by a discharge inside bubbles in water is proposed. Radicals with short lifetime (atomic oxygen and OH radical) are used effectively for the water purification because those are generated by discharge inside bubbles in water. OH radical production was confirmed by a light emission of the discharge using the spectroscopic technique. Dissolved ozone concentration of about 0.3 mg/1 was obtained when oxygen was used as a bubbling gas. Decolorization process of indigo solution by a discharge inside bubbles in water was investigated.