Investigation on Electrical and Magnetic Properties of Gd-doped BiFeO<Subscript>3</Subscript>

Multiferroic ceramic samples of Bi_1−x Gd _x FeO₃ (x=0, 0.05, 0.1 and 0.15) have been prepared by rapid liquid-phase sintering technique. The effect of Gd substitution on ferroelectric and magnetic properties of Bi_1−x Gd _x FeO₃ ceramics has been investigated. The results of X-ray diffraction (XRD) patterns show that the single-phase BiFeO₃ sample has a rhombohedral structure and Gd³⁺ substitution for Bi³⁺ has not affected its structure. Experimental results suggest that for Bi_1−x Gd _x FeO₃ system, the ferroelectric and magnetic properties of BiFeO₃ are improved by Gd doping and the loop area increases with the Gd content. When x=0.15, saturated ferroelectric hysteresis loop is observed at room temperature with the maximal 2Pr=1.62 μC/cm², which is about 578.6% higher than that of BiFeO₃.     

Inducing multiferroic behaviour in the diamagnetic Y<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The synthesis and characterization of Y_2−xFe_xO₃ (where x = 0–0.3) compounds has been carried out for their importance in the field of multiferroic materials. The powder X-ray diffraction reveal that the compounds Y_1.95Fe_0.05O₃, Y_1.9Fe_0.1O₃, Y_1.85Fe_0.15O₃ and Y_1.8Fe_0.2O₃ crystallize in tetragonal structure whereas Y_1.75Fe_0.25O₃ and Y_1.7Fe_0.3O₃ compounds crystallize in orthorhombic structure. The change in crystal system with respect to the concentration of Fe may be attributed to the variation in occupancy position of Fe³⁺ into the Y³⁺ site of Y₂O₃ system. Variation in crystal structure, surface morphology and composition was studied by micro-Raman analysis, SEM and EDX analysis. The shift in intense Raman signals from 426 to 385 cm⁻¹ confirms the change in the crystal structure of the prepared compounds. Further it is also identified that the E_g mode of vibration is the dominant in the Fe substituted compounds. The substitution of Fe in the Y₂O₃ system leads to the increase in the intensity of resonance band, which indicates a large polarisability variation in the Y_2−xFe_xO₃ compounds. Diffused reflectance studies show a red shift in energy gap values while increasing the concentration of Fe. The room temperature magnetization and electron paramagnetic resonance studies reveal that the incorporation of Fe in the Y₂O₃ system leads to magnetic phase change from diamagnetic to ferromagnetic. The electric polarization studies imply that the substitution of lower ionic radii element Fe³⁺ in the Y³⁺ site leads to distortion in the lattice and show the way to spontaneous dipole moment and it was found that the Y_1.8Fe_0.2O₃ compound exhibits the possibility of multiferroic behaviour. Therefore this paper explores the possibility of inducing ferromagnetic and ferroelectric behaviour in the Fe substituted yttrium oxide system.     

Enhanced Superconducting Properties of Air-Processed GdBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7-δ</Subscript> Single Domains with BaCO<Subscript>3</Subscript>/BaCuO<Subscript>2−<Emphasis Type="Italic">x</Emphasis></Subscript> Addition

Single domain GdBa₂Cu_7-δ (Gd123) bulk superconductors were fabricated in air by top-seeding melt-texture growth. Performance of the air-processed Gd123 was successfully enhanced by addition of both BaCO₃ and BaCuO_2−x , which suppress the formation of Gd_1+x Ba_2−x Cu₃O_7-δ solid solutions. The optimum doping amount ranges from 0.05 to 0.15, M BaCO₃ and 0.05 to 0.1, M BaCuO_2−x per molar Gd123. The distribution of the second phase particles was observed by scanning electron microscopy. A narrow band formed by Gd₂BaCuO₅ particle concentration appeared around the seeding zone in both a–b plane and c-growth sector in Gd123 single grain. Trapped magnetic field density reached 0.67, T for sample with 24 mm in diameter and 8, mm in thickness and a high critical current density J _c up to 91,200, A/cm² was achieved at 77, K under self-field.     

Effect of Nd substitution on structure and magnetic properties of Nd<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Dy<Subscript>3−<Emphasis Type="Italic">x</Emphasis></Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> garnet powders

The properties of light rare earth Nd substitution for heavy rare earth Dy in Dy₃Fe₅O₁₂ (DyIG) garnet ferrite have been studied. The Nd _x Dy_3–x Fe₅O₁₂ (x = 0, 0.25, 0.5, 0.75 and 1) (Nd:DyIG) garnet powders were prepared by sol–gel autocombustion followed by heat treatment. The structure and the magnetic properties of the annealed powders were measured with X-ray diffraction (XRD), the Fourier Transform Infrared (FT-IR) and the Physical Properties Measurement System (PPMS) techniques. The experimental results indicate that a single Nd:DyIG garnet phase structure can be obtained after the samples annealed above 800 °C. With the Nd substitution content increasing, the average lattice constants of the sample, the a−d super-exchange interaction strengthens and the magnetization of unit cell increase. The maximum saturation magnetization is 13.86 emu/g for x = 1, and coercive force is about 136 Oe, for x = 0.75. The reason of increasing in magnetization with Nd substitution is also discussed.     

Synthesis and properties of AgTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-based NASICON-type phosphates doped with Nb<Superscript>5+</Superscript>, Zr<Superscript>4+</Superscript>, and Ga<Superscript>3+</Superscript>

We have synthesized materials based on a silver titanium phosphate with partial substitution of tri-, tetra-, or pentavalent cations for titanium: Ag_1±x Ti_2−x M _x (PO₄)₃ (M = Nb⁵⁺, Ga³⁺) and AgTi_2−x Zr _x (PO₄)₃. The materials have been characterized by X-ray diffraction and impedance spectroscopy and have been shown to have small thermal expansion coefficients. Their ionic conductivity has been determined. Silver ions in these materials are difficult to replace with protons.     

Magnetic properties of Nd-Y<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles

Nb³⁺-substituted garnet nanoparticles Y_3−xNd_xFe₅O₁₂ (x = 0.0, 0.5, 1.0, 1.5, and 2.0) were fabricated by a sol-gel method and their crystalline structures and magnetic properties were investigated by using X-ray diffraction (XRD), thermal analysis (DTA/TG), and vibrating sample magnetometer (VSM). The XRD patterns of Y_3−xNd_xFe₅O₁₂ have only peaks of the garnet structure and the sizes of particles range from 34 to 70 nm. From the results of VSM, it is shown that when the Nd concentration x ( 1.0, the saturation magnetization of Y_3−xNd_xFe₅O₁₂ increases as the Nd concentration (x) is increased, and gets its maximum at x = 1.0, but when x ( 1.0, the saturation magnetization decreases with increasing the Nd concentration (x), this may be due to the distortion of the microstructure of Y_3−xNd_xFe₅O₁₂, which leads to the decrease of the effective moment formed by Fe³⁺. Meanwhile, it is observed that with the enhancement of the surface spin effects, the saturation magnetization rises as the particle size is increased.     

Influence of Zr doping on the dielectric properties of CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> ceramics

Pure and Zr-substituted CaCu₃(Ti_1−x Zr _x )₄O₁₂ (x = 0, 0.01, 0.02, 0.03) ceramics were prepared by the Pechini method. X-ray powder diffraction analysis indicated the formation of single-phase compound, and all the diffraction peaks were completely indexed by the body-centered cubic perovskite-related structure. The effects of Zr⁴⁺ ion substituting partially Ti⁴⁺ ion on the dielectric properties were investigated in frequency range between 100 Hz and 1 GHz. The low frequency (f ≤ 10⁵ Hz) dielectric constant decreases with Zr substitution and the high frequency (f ≥ 10⁷ Hz) dielectric constant is unchanged. Interestingly, a low-frequency relaxation was observed at room temperature through Zr substitution. The observed dielectric properties in Zr-substituted samples were discussed using the internal barrier layer capacitor model. A corresponding equivalent circuit was adopted to explain the dielectric dispersion. The characteristic frequency of low-frequency relaxation rises due to the decrease of the resistivity of grain boundary with Zr substitution, which is likely responsible for the large low-frequency response at room temperature.     

Study of structure and properties of ZnO–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Glasses of the ternary system ZnO–Bi₂O₃–P₂O₅ were prepared and studied in two compositional series 50ZnO–xBi₂O₃–(50 − x)P₂O₅ and (50 − y)ZnO–yBi₂O₃–50P₂O₅. Two distinct glass-forming regions were found in the 50ZnO–xBi₂O₃–(50 − x)P₂O₅ glass series with x = 0–10 and 20–35 mol.% Bi₂O₃. All prepared Bi₂O₃-containing glasses reveal a high chemical durability. Small additions of Bi₂O₃ (∼5 mol.%) improve thermal stability of glasses. All glasses crystallize on heating within the temperature range of 505–583 °C. Structural studies by Raman and ³¹P MAS NMR spectroscopies showed the rapid depolymerisation of phosphate chains within the first region with x = 0–15 and the presence of isolated Q⁰ phosphate units within the second region with x = 20–35. Raman studies showed that bismuth is incorporated in the glass structure in BiO₆ units and their vibrational bands were observed within the spectral region of 350–700 cm⁻¹. The evolution of properties and the spectroscopic data are both in accordance with a network former effect of Bi₂O₃.     

Enhancement of Critical Current Density in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7−<Emphasis Type="Italic">y</Emphasis></Subscript> HTS Through Boron Addition

The effect of B₂O₃ addition on the superconducting transition and grain boundary critical current density of the boron free (control) and boron doped HTS ceramics with nominal composition YBa₂Cu₃B _x O_7−y (x=0, 0.025, 0.05, 0.075, 0.1 and 0.15) has been investigated. For the lowest-level boron doping (x=0.025) an increase by nearly 1.5 times was observed in the critical current density J _c compared to the control sample. The small additives of boron in YBa₂Cu₃B _x O_7−y (x=0.025 and 0.05) do not essentially affect the critical temperature T _c =92.5 K of nominally pure Y123. Higher-level boron added compounds revealed a decrease in both T _c and J _c values. The data obtained indicate the possibility of boron dopant being inserted either into interstitial or into substitutional sites of the lattice.     

Synthesis,photoluminescence and mechanoluminescence properties of Eu<Superscript>3+</Superscript> ions activated Ca<Subscript>2</Subscript>Gd<Subscript>2</Subscript>W<Subscript>3</Subscript>O<Subscript>14</Subscript> phosphors

A new series of Eu³⁺ ions-activated calcium gadolinium tungstate [Ca₂Gd₂W₃O₁₄] phosphors were synthesized by conventional solid-state reaction method. The X-ray diffraction patterns of the powder samples indicate that the Eu³⁺: Ca₂Gd₂W₃O₁₄ phosphors are of tetragonal structure. The prepared phosphors were well characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), Fourier transform infrared spectroscopy (FTIR), photoluminescence (PL), and mechanoluminescence (ML) spectra. PL spectra of Eu³⁺: Ca₂Gd₂W₃O₁₄ powder phosphors have shown strong red emission at 615 nm (⁵D₀ → ⁷F₂) with an excitation wavelength λ _exci = 392 nm (⁷F₀ → ⁵L₆). The energy transfer from tungstate groups to europium ions has also reported. Mechanoluminescence studies of Eu³⁺: Ca₂Gd₂W₃O₁₄ phosphors have also been explained systematically.     

Synthesis and Superconductivity in Ba-doped (Ru,Cu)(Sr,Nd)<Subscript>2</Subscript>(Nd,Ce)<Subscript>2</Subscript>Cu<Subscript>2</Subscript>O<Subscript><Emphasis Type="Italic">z</Emphasis></Subscript> Compounds

We prepared various (Ru_0.5Cu_0.5)(Sr_1.67−x Ba _x Nd_0.33)(Nd_1.34Ce_0.66)Cu₂O _z samples with varying Ba contents by x=0, 0.1, 0.2, 0.33, 0.5 and 0.835. X-ray diffraction revealed that the phase purity of the samples increases as the Ba-doping content increases and single- phase compounds could be obtained for samples with 0.1≤x≤0.33. Contrary to the Ba-free sample, superconductivity could be induced by partially substituting Ba for Sr and superconductivity with onset T _c of about 15 K is observed for the sample with x=0.2. The superconducting behavior of the Ba-doped samples is discussed in conjunction with thermoelectric power measurements.     

Microstructure and H<Subscript>2</Subscript>S gas sensing properties of nanocrystalline perovskite-type La<Subscript>0.6</Subscript>Co<Subscript>0.4</Subscript>Mn<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>O<Subscript>3</Subscript>

Nanocrystalline La_1−x Co _x Mn_1−y Ni _y O₃ (x = 0.2 and 0.4; y = 0.1, 0.3, and 0.5) thick films sensors prepared by sol–gel method were studied for their H₂S gas sensitivity. The structural and morphological properties have been carried out by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Average particle size estimated from XRD and TEM analyses was observed to be 30–35 nm. The gas response characteristics were found to depend on the dopants concentration and operating temperature. The maximum H₂S gas response of pure LaMnO₃ was found to be at 300 °C. In order to improve the gas response, material doped with transition metals Co and Ni on A- and B-site, respectively. The La_0.6Co_0.4Mn_0.5Ni_0.5O₃ shows high response towards H₂S gas at an operating temperature 250 °C. The Pd-doped La_0.6Co_0.4Mn_0.5Ni_0.5O₃ sensor was found to be highly sensitive to H₂S at an operating temperature 200 °C. The gas response, selectivity, response time and recovery time were studied and discussed.     

Influence of Sm substitution on the phase,microstructure and microwave dielectric properties of SrLa<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>17</Subscript>

New dielectric ceramics in the SrLa_4−xSm_xTi₅O₁₇ (0 ≤ x ≤ 4) composition series were prepared through a solid state mixed oxide route to investigate the effect of Sm⁺³ substitution for La⁺³ on the phase, microstructure and microwave dielectric properties. At x = 0–3, all the compositions formed single phase ceramics within the detection limit of in-house X-ray diffraction when sintered in the temperature range 1500–1580 °C. At x = 4, a mixture of Sm₂Ti₂O₇ and SrTiO₃ formed. The maximum Sm⁺³-containing single phase ceramics, SrLaSm₃Ti₅O₁₇, exhibited relative permittivity (ε_r) = 42.6, temperature coefficient of resonant frequency (τ _f ) = −96 ppm/^oC and quality factor (Q _u f _o ) = 7332 GHz. An analysis of results presented here indicates that SrLa_4−xSm_xTi₅O₁₇ ceramics, exhibiting τ _f  ~ 0 and ε_r ~ 53 could be achieved at x ~ 1.4 but at the cost of decrease in Q _u f _o .     

The synthesis and the magnetic properties of Sm<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>BiY<Subscript>2–<Emphasis Type="Italic">x</Emphasis></Subscript>Fe<Subscript>5</Subscript>O<Subscript>12 </Subscript>nanoparticles

Sm _x BiY_2–x Fe₅O₁₂ (x = 0, 0.1, 0.2, 0.4, 0.6, 0.8) nanocrystals were fabricated by sol–gel method. Samples were characterized by powder X-ray diffraction (XRD), thermal gravity analysis (TGA) and differential thermal analysis (DTA), transmission electron microscopy (TEM), vibrating sample magnetometer(VSM). The samples were calcined at 850 °C and 1000 °C and the average size of the particles were determined by Scherrer’s formula . In this paper, we discussed the effect of Sm³⁺ substitution for Y³⁺ on magnetic properties of BiY₂Fe₅O₁₂. The magnetic properties of Sm _x BiY_2−x Fe₅O₁₂ are decreased with increasing content of Sm ion.     

Influence of isovalent and heterovalent substitution for Bi<Superscript>3+</Superscript> and Fe<Superscript>3+</Superscript> on the properties of Bi<Subscript>2</Subscript>Fe<Subscript>4</Subscript>O<Subscript>9</Subscript>-based solid solutions

Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites have been prepared by solid-state reactions at a temperature of 1073 K. X-ray diffraction data indicate that, in the Bi_2–хLa_хFe₄O₉ system, the limiting degree of La³⁺ substitution for Bi³⁺ ions in Bi₂Fe₄O₉ does not exceed 0.05 and that the limiting degree of substitution in the Bi₂Fe_4–2xTi_xCo_xO₉ system lies in the range 0.05 < x < 0.1. The specific magnetization and specific magnetic susceptibility of the samples have been measured at temperatures from 5 to 300 K in a magnetic field of 0.86 T. The field dependences of magnetization obtained for the Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites at temperatures of 300 and 5 K demonstrate that partial isovalent substitution of La³⁺ for Bi³⁺ ions in Bi₂Fe₄O₉ and heterovalent substitution of Ti⁴⁺ and Co²⁺ ions for two Fe³⁺ ions leads to partial breakdown of the antiferromagnetic state and nucleation of a ferromagnetic state.     

Effects of Nd-substitution on microstructures and dielectric characteristics of CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> ceramics

Ca_1−3x/2Nd _x Cu₃Ti₄O₁₂ (x = 0, 0.1, 0.2) ceramics were prepared by a solid state reaction process, and single-phased structures were obtained for all the compositions. The dielectric characteristics of pure and Nd-substituted CaCu₃Ti₄O₁₂ ceramics were investigated together with the microstructures. The mixed-valent structures of Cu⁺/Cu²⁺ and Ti³⁺/Ti⁴⁺ in the present ceramics were confirmed by X-ray photoelectron analysis. The dielectric relaxation in the low temperature range was examined in detail and the variation of dielectric constant and dielectric loss was attributed to the modification mixed-valent structures.     

Dielectric and ferromagnetic properties of BaTiO<Subscript>3</Subscript>/Ni<Subscript>0.93</Subscript>Co<Subscript>0.02</Subscript>Cu<Subscript>0.05</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> composites

xBaTiO₃ + (1 − x)Ni_0.93Co_0.02Cu_0.05Fe₂O₄ (x = 0.5, 0.6, 0.7, 0.8) composites with ferroelectric–ferromagnetic characteristics were synthesized by the ceramic sintering technique. The presence of constituent phases in the composites was confirmed by X-ray diffraction studies. The average grain size was calculated by using a scanning electron micrograph. The dielectric characteristics were studied in the 100 kHz to 15 MHz. The dielectric constant changed higher with ferroelectric content increasing; and it was constant in this frequency range. The relation of dielectric constant with temperature was researched at 1, 10, 100 kHz. The Curie temperature would be higher with frequency increasing. The hysteresis behavior was studied to understand the magnetic properties such as saturation magnetization (M _s). The composites were a typical soft magnetic character with low coercive force. Both the ferroelectric and ferromagnetic phases preserve their basic properties in the bulk composite, thus these composites are good candidates as magnetoelectric materials.     

Synthesis and sintering of nano-sized BaSnO<Subscript>3</Subscript> powders containing BaGeO<Subscript>3</Subscript>

The formation of solid solutions of the type [Ba(HOC₂H₄OH)₄][Sn_1−x Ge _x (OC₂H₄O)₃] as BaSn_1−x /Ge _x O₃ precursor and the phase evolution during its thermal decomposition are described in this paper. The 1,2-ethanediolato complexes can be decomposed to nano-sized BaSn_1−x /Ge _x O₃ preceramic powders. Samples with x = 0.05 consist of only a Ba(Sn,Ge)O₃ phase, whereas powders with x = 0.15 and 0.25 show diffraction patterns of both the Ba(Sn,Ge)O₃ and BaGeO₃ phase. The sintering behaviour was investigated on powders with a BaGeO₃ content of 5 and 15 mol%. These powders show a specific surface area of 15.4–15.9 m²/g and were obtained from calcination above 800 °C. The addition of BaGeO₃ reduced the sintering temperature of the ceramics drastically. BaSn_0.95Ge_0.05O₃ ceramics with a relative density of at least 90% can be obtained by sintering at 1150 °C for 1 h. The ceramic bodies reveal a fine microstructure with cubical-shaped grains between 0.25 and 0.6 μm. For dense ceramics, the sintering temperature could be reduced down to 1090 °C, when the soaking time was extended up to 10 h.     

Phase,microstructural characterization and dielectric properties of Ca-substituted Sr<Subscript>5</Subscript>Nb<Subscript>4</Subscript>TiO<Subscript>17</Subscript> ceramics

The effect of Ca substitution for Sr on the phase, microstructure and microwave dielectric properties of the Sr_5−x Ca _x Nb₄TiO₁₇ composition series was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), an LCR meter, and vector network analyzer. Below 1450 °C, Sr_5−x Ca _x Nb₄TiO₁₇ (x = 1, 2, 3, or 4) compositions formed single-phase Sr₄CaNb₄TiO₁₇, Sr₃Ca₂Nb₄TiO₁₇, Sr₂Ca₃Nb₄TiO₁₇, and SrCa₄Nb₄TiO₁₇ ceramics, respectively. At x = 0 and 5, Sr₅Nb₄TiO₁₇ and Ca₅Nb₄TiO₁₇ formed, but along with Sr₂Nb₂O₇ (at x = 0) and CaNbO₃ and CaNb₂O₆ (at x = 5) secondary phases. Above 1450 °C, all the compositions formed two-phase ceramics. At low frequencies, a phase transition was observed in the composition Sr₅Nb₄TiO₁₇. The substitution of Ca for Sr enabled processing of highly dense Sr₂Ca₃Nb₄TiO₁₇, with ε_r ~ 53.4, τ_f ~ −6.5 ppm/°C and Q _u  × f _o  ~ 1166 GHz. Further investigations are required to improve the quality factor of these ceramics for possible microwave applications.     

Synthesis,structural, photoluminescence and mechanoluminescence properties of Tb<Superscript>3+</Superscript>: Ca<Subscript>2</Subscript>Gd<Subscript>2</Subscript>W<Subscript>3</Subscript>O<Subscript>14</Subscript> novel green nanophosphors

Novel green nanophosphors Ca₂Gd₂W₃O₁₄: Tb³⁺ were synthesized by solid state reaction method. From the X-ray diffraction profiles it is observed that Tb³⁺: Ca₂Gd₂W₃O₁₄ phosphors were crystallized in the form of tetragonal structure. The scanning electron microscopy (SEM) image shows that the particle size is at around 300 nm. In addition to these the prepared powder phosphors were also examined by the energy dispersive X-ray analysis (EDAX), Fourier transform infrared spectroscopy (FTIR), photoluminescence (PL) and mechanoluminescence (ML) spectra. Emission spectra of Tb³⁺: Ca₂Gd₂W₃O₁₄ nanophosphors have shown bright green emission at 545 nm (⁵D₄ → ⁷F₅) with an excitation wavelength λ_exci = 374 nm (⁷F₆ → ⁵G₆). ML spectra shows the radiation effect on the Ca₂Gd₂W₃O₁₄: Tb³⁺ nanophosphors and from that it was observed that these phosphors are very less sensitive for lower exposure.