Fabrication of a thermoresponsive cell culture dish: a key technology for cell sheet tissue engineering

Abstract

This article reviews the properties and characterization of an intelligent thermoresponsive surface, which is a key technology for cell sheet-based tissue engineering. Intelligent thermoresponsive surfaces grafted with poly(N-isopropylacrylamide) exhibit hydrophilic/hydrophobic alteration in response to temperature change. Cultured cells are harvested on thermoresponsive cell culture dishes by decreasing the temperature without the use of digestive enzymes or chelating agents. Our group has developed cell sheet-based tissue engineering for therapeutic uses with single layer or multilayered cell sheets, which were recovered from the thermoresponsive cell culture dish. Using surface derivation techniques, we developed a new generation of thermoresponsive cell culture dishes to improve culture conditions. We also designed a new methodology for constructing well-defined organs using microfabrication techniques.     

Intact endothelial cell sheet harvesting from thermoresponsive surfaces coated with cell adhesion promoters.

Recently, with the development of smart polymers, research has looked to using thermoresponsive polymers as cell culture substrates. These novel surfaces allow the cultivation of cells without enzymes using the thermoresponsive phase transition property of poly(N-isopropylacrylamide) (PNIPAAm). However, this requires expensive techniques to generate a sufficiently thin film that allows cell adhesion. In this study, we looked at simple solvent cast films which normally show poor cell adhesion, but here the films are coated with cell adhesion promoters (CAPs) to improve cell growth without altering the copolymer thermoresponsive behaviour.A copolymer of PNIPAAm and N-tert-butylacrylamide (NtBAm) with a ratio of 85:15, respectively, was synthesized and solvent cast. The copolymer films were coated with CAPs, such as collagen, fibronectin and laminin, to increase their cell adhesion and growth properties. Cell activity measured by the alamarBlue assay showed similar results for coated copolymer films and standard tissue culture plastic controls. Deposition of CAPs on to the copolymer films was characterized by scanning electron microscopy and atomic force microscopy. Cell detachment from the copolymer films is not affected by the surface coatings of CAPs, and endothelial cells are recovered as an intact sheet, which has great potential for uses in tissue engineering applications. The results demonstrate a versatile method for the cultivation of cells while eliminating the need for the use of digestive enzymes such as trypsin. This study shows that cultivation on physically bonded PNIPAAm copolymers is viable and achievable by relatively simple methods.     

Thermally reversible colloidal gels for three-dimensional chondrocyte culture

Healthy cells are required in large numbers to form a tissue-engineered construct and primary cells must therefore be increased in number in a process termed ‘expansion’. There are significant problems with existing procedures, including cell injury and an associated loss of phenotype, but three-dimensional culture has been reported to offer a solution. Reversible gels, which allow for the recovery of cells after expansion would therefore have great value in the expansion of chondrocytes for tissue engineering applications, but they have received relatively little attention to date. In this study, we examined the synthesis and use of thermoresponsive polymers that form reversible three-dimensional gels for chondrocyte cell culture. A series of polymers comprising N-isopropylacrylamide (NIPAM) and styrene was synthesized before studying their thermoresponsive solution behaviour and gelation. A poly(NIPAM-co-styrene-graft-N-vinylpyrrolidone) variant was also synthesized in order to provide increased water content. Both random- and graft-copolymers formed particulate gels above the lower critical solution temperature and, on cooling, re-dissolved to allow enzyme-free cell recovery. Chondrocytes remained viable in all of these materials for 24 days, increased in number and produced collagen type II and glycosaminoglycans.     

Thermally responsive polymeric hydrogel brushes: synthesis, physical properties and use for the culture of chondrocytes

Hydrogel brushes are materials composed of a water-swollen network, which contains polymer chains that are grafted with another polymer. Using a thermally responsive polymer, poly(N-isopropyl acrylamide) (polyNIPAM), as the graft component we are able to maintain the critical solution temperature (Tcrit), independent of the overall composition of the material, at approximately 32 degrees C. The change in swelling at Tcrit is a function of the amount of polyNIPAM in the system. However, there is a much smaller change in the surface contact angles at Tcrit. PolyNIPAM-based materials have generated considerable interest, as 'smart' substrates for the culture of cells and here, we show the utility of hydrogel brushes in cell culture. Chondrocytes attached to the hydrogel brushes and yielded viable cell cultures. Moreover, the chondrocytes could be released from the hydrogel brushes without the use of proteases by reducing the temperature of the cultures to below Tcrit to induce a change in the conformation of the polyNIPAM chain at Tcrit. The importance of the crosslink hydrogel component is illustrated by significant changes in cell attachment/cell viability as the crosslink density is changed.     

Surface design with self-heating smart polymers for on–off switchable traps

We have developed a novel self-heating, temperature-responsive chromatography system for the effective separation of biomolecules. Temperature-responsive poly(N-isopropylacrylamide-co-N-hydroxymethylacrylamide), poly(NIPAAm-co-HMAAm), was covalently grafted onto the surface of magnetite/silica composites as ‘on-off’ switchable surface traps. The lower critical solution temperature (LCST) of the poly(NIPAAm-co-HMAAm)s was controlled from 35 to 55 °C by varying the HMAAm content. Using the heat generated by magnetic particles in an alternating magnetic field (AMF) we were able to induce the hydrophilic to hydrophobic phase separation of the grafted temperature-responsive polymers. To assess the feasibility of the poly(NIPAAm-co-HMAAm)-grafted magnetite/silica particles as the stationary phase for chromatography, we packed the particles into the glass column of a liquid chromatography system and analyzed the elusion profiles for steroids. The retention time for hydrophobic steroids markedly increased in the AMF, because the hydrophobic interaction was enhanced via self-heating of the grafted magnetite/silica particles, and this effect could be controlled by changing the AMF irradiation time. Turning off the AMF shortened the total analysis time for steroids. The proposed system is useful for separating bioactive compounds because their elution profiles can be easily controlled by an AMF.     

Novel temperature-responsive polymer brushes with carbohydrate residues facilitate selective adhesion and collection of hepatocytes

Temperature-responsive glycopolymer brushes were designed to investigate the effects of grafting architectures of the copolymers on the selective adhesion and collection of hypatocytes. Homo, random and block sequences of N-isopropylacrylamide and 2-lactobionamidoethyl methacrylate were grafted on glass substrates via surface-initiated atom transfer radical polymerization. The galactose/lactose-specific lectin RCA₁₂₀ and HepG2 cells were used to test for specific recognition of the polymer brushes containing galactose residues over the lower critical solution temperatures (LCSTs). RCA₁₂₀ showed a specific binding to the brush surfaces at 37 °C. These brush surfaces also facilitated the adhesion of HepG2 cells at 37 °C under nonserum conditions, whereas no adhesion was observed for NIH-3T3 fibroblasts. When the temperature was decreased to 25 °C, almost all the HepG2 cells detached from the block copolymer brush, whereas the random copolymer brush did not release the cells. The difference in releasing kinetics of cells from the surfaces with different grafting architectures can be explained by the correlated effects of significant changes in LCST, mobility, hydrophilicity and mechanical properties of the grafted polymer chains. These findings are important for designing ‘on–off’ cell capture/release substrates for various biomedical applications such as selective cell separation.     

Synthesis of thermoresponsive poly(N-isopropylacrylamide) brush on silicon wafer surface via atom transfer radical polymerization

Thermoresponsive poly(N-isopropylacrylamide) [poly(NIPAM)] brush on silicon wafer surface was prepared by combining the self-assembled monolayer of initiator and atom transfer radical polymerization (ATRP). The resulting polymer brush was characterized by in situ reflectance Fourier transform infrared spectroscopy, atomic force microscopy and ellipsometry techniques. Gel permeation chromatography determination of the number-average molecular weight and polydispersity index of the brush detached from the silicon wafer surface suggested that the surface-initiated ATRP method can provide relatively homogeneous polymer brush. Contact angle measurements exhibited a two-stage increase upon heating over the board temperature range 25-45 °C, which is in contrast to the fact that free poly(NIPAM) homopolymer in aqueous solution exhibits a phase transition at ca. 34 °C within a narrow temperature range. The first de-wetting transition takes place at 27 °C, which can be tentatively attributed to the n-cluster induced collapse of the inner region of poly(NIPAM) brush close to the silicon surface; the second de-wetting transition occurs at 38 °C, which can be attributed to the outer region of poly(NIPAM) brush, possessing much lower chain density compared to that of the inner part.     

Calcium-phosphate derived from mineralized algae for bone tissue engineering applications

In this work, several routes are described towards obtaining pure inorganic phases derived from Coralline officinallis red algae. The scanning electron microscopy studies have shown that it becomes possible not only to eliminate the undesired organic phase, but also to preserve or tailor the red algae typical microporosity. X-ray diffraction analysis was used to investigate the phase content of the red algae before and after performing the different treatment routes. Hydroxyapatite nanocrystallites were obtained after converting the coralline calcium carbonate skeleton by means of combining thermal and chemical routes. These results were confirmed by Fourier transform infra-red spectroscopic analysis. The processing routes herein described are very promising in order to design bioceramics of algae origin that might find useful applications as bone fillers and tissue engineering scaffolds.     

Fabrication of a novel micro-nano fibrous nonwoven scaffold with Antheraea assama silk fibroin for use in tissue engineering

The success of developing artificial organs by tissue engineering depends on scaffold properties and architecture. Here, we describe the fabrication of an Antheraea assama fibroin based novel micro-nano fibrous nonwoven scaffold. The morphological and chemical characterization was done by scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR) respectively, which demonstrated the formation of scaffold with micro-nano architecture. The biocompatibility was assessed in vitro by haemolysis and cytotoxicity assays, whereby the scaffold was found to be nontoxic and efficient in supporting cell adhesion and growth.     

聚乳酸组织工程支架表面涂覆钙磷盐的工艺研究

提出了以聚乳酸／钙磷盐／胶原的骨组织工程支架快速成形制造的材料系统，对比了两种在聚乳酸(PLA)表面涂覆钙磷盐的工艺．一种是将聚乳酸组织工程支架浸泡在模拟体液中采用平衡反应法沉积钙磷盐；另一种是在聚乳酸薄膜上采用非平衡反应法沉积钙磷盐；系统地研究了沉积时间和沉积量、钙磷摩尔比和相结构演变的关系；通过控制反应时间和调整反应物配比获得磷酸四钙(TetCP)-PLA和无定形磷酸钙(ACP)—PLA等材料组合；并对所获得的复合材料进行生物相容性试验．对比试验证明细胞在材料表面生长良好，采用两种方法涂覆钙磷盐均改进了聚乳酸的生物相容性．     

The role of the surface on microglia function: implications for central nervous system tissue engineering

In tissue engineering, it is well accepted that a scaffold surface has a decisive impact on cell behaviour. Here we focused on microglia—the resident immune cells of the central nervous system (CNS)—and on their response to poly(trimethylene carbonate-co-ε-caprolactone) (P(TMC-CL)) fibrous and flat surfaces obtained by electrospinning and solvent cast, respectively. This study aims to provide cues for the design of instructive surfaces that can contribute to the challenging process of CNS regeneration. Cell morphology was evidently affected by the substrate, mirroring the surface main features. Cells cultured on flat substrates presented a round shape, while cells with elongated processes were observed on the electrospun fibres. A higher concentration of the pro-inflammatory cytokine tumour necrosis factor-α was detected in culture media from microglia on fibres. Still, astrogliosis is not exacerbated when astrocytes are cultured in the presence of microglia-conditioned media obtained from cultures in contact with either substrate. Furthermore, a significant percentage of microglia was found to participate in the process of myelin phagocytosis, with the formation of multinucleated giant cells being observed only on films. Altogether, the results presented suggest that microglia in contact with the tested substrates may contribute to the regeneration process, putting forward P(TMC-CL) substrates as supporting matrices for nerve regeneration.     

An efficient dye-sensitized solar cell based on a functionalized-triarylamine dye

A new functionalized-triarylamine dye (MXD10) has been designed, synthesized, and characterized. Two CH₃(CH₂)₄CH=CH- units were introduced into triphenylamine for improvement of light harvesting, suppression of dye aggregation and retardation of charge recombination. Photophysical, electrochemical and photovoltaic measurements are in accord with the molecular design. Device based on MXD10 gave a maximum power conversion efficiency of 6.47% under simulated AM 1.5 irradiation (100 mW cm⁻²) with J_SC = 15 mA/cm², V_OC = 635 mV, and ff = 0.68.     

Incorporation of vitamin E in poly(3hydroxybutyrate)/Bioglass composite films: effect on surface properties and cell attachment

This study investigated the possibility of incorporating α-tocopherol (vitamin E) into poly(3hydroxybutyrate) (P(3HB))/Bioglass composites, which are being developed for bone tissue engineering matrices. P(3HB) films with 20 wt% Bioglass and 10 wt% vitamin E were prepared using the solvent casting technique. Addition of vitamin E significantly improved the hydrophilicity of the composites along with increasing the total protein adsorption. The presence of protein adsorbed on the composite surface was further confirmed using X-ray photoelectron spectroscopy analysis. Preliminary cell culture studies using MG-63 human osteoblasts showed that the addition of vitamin E in the P(3HB)/20 wt% Bioglass films significantly increased cell proliferation. The results achieved in this study confirmed the possibility of incorporating vitamin E as a suitable additive in P(3HB)/Bioglass composites to engineer the surface of the composites by promoting higher protein adsorption and increasing the hydrophilicity.     

Processing of novel bioactive polymeric matrixes for tissue engineering using supercritical fluid technology

The aim of this study was to develop a new process for the production of bioactive 3D scaffolds using a clean and environmentally friendly technology. The possibility of preparing composite scaffolds of Bioglass^® and a polymeric blend of starch and poly(l-lactic acid) (SPLA50) was evaluated. Supercritical phase-inversion technique was used to prepare inorganic particles loaded starch-based porous composite matrixes in a one-step process for bone tissue engineering purposes.Due to their osteoconductive properties some glasses and ceramics are interesting materials to be used for bone tissue engineering purposes; however their poor mechanical properties create the need of a polymeric support where the inorganic fraction can be dispersed. Samples impregnated with different concentrations of Bioglass^® (10 and 15% wt/wt polymer) were prepared at 200 bar and 55 °C. The presence of Bioglass^® did not affect the porosity or interconnectivity of the polymeric matrixes. Dynamic mechanical analysis has proven that the modulus of the SPLA50 scaffolds increases when glass particles are impregnated within the matrix.In vitro bioactivity studies were carried out using simulated body fluid and the results show that a calcium-phosphate layer started to be formed after only 1 day of immersion. Chemical analysis of the apatite layer formed on the surface of the scaffold was performed by different techniques, namely EDS and FTIR spectroscopy and X-ray diffraction (XRD). The ion concentration in the simulated body fluid was also carried out by ICP analysis. Results suggest that a bone-like apatite layer was formed.This study reports the feasibility of using supercritical fluid technology to process, in one step, a porous matrix loaded with a bioactive material for tissue engineering purposes.     

Modelling planar polarity of epithelia: the role of signal relay in collective cell polarization

Collective cell polarization is an important characteristic of tissues. Epithelia commonly display cellular structures that are polarized within the plane of the tissue. Establishment of this planar cell polarity requires mechanisms that locally align polarized structures between neighbouring cells, as well as cues that provide global information about alignment relative to an axis of a tissue. In the Drosophila ovary, the cadherin Fat2 is required to orient actin filaments located at the basal side of follicle cells perpendicular to the long axis of the egg chamber. The mechanisms directing this orientation of actin filaments, however, remain unknown. Here we show, using genetic mosaic analysis, that fat2 is not essential for the local alignment of actin filaments between neighbouring cells. Moreover, we provide evidence that Fat2 is involved in the propagation of a cue specifying the orientation of actin filaments relative to the tissue axis. Monte Carlo simulations of actin filament orientation resemble the results of the genetic mosaic analysis, if it is assumed that a polarity signal can propagate from a signal source only through a connected chain of wild-type cells. Our results suggest that Fat2 is required for propagating global polarity information within the follicle epithelium through direct cell–cell contact. Our computational model might be more generally applicable to study collective cell polarization in tissues.     

Three-dimensional printing of biomaterials for bone tissue engineering: a review

Processing biomaterials into porous scaffolds for bone tissue engineering is a critical and a key step in defining and controlling their physicochemical, mechanical, and biological properties. Biomaterials such as polymers are commonly processed into porous scaffolds using conventional processing techniques, e.g., salt leaching. However, these traditional techniques have shown unavoidable limitations and several shortcomings. For instance, tissue-engineered porous scaffolds with a complex three-dimensional (3D) geometric architecture mimicking the complexity of the extracellular matrix of native tissues and with the ability to fit into irregular tissue defects cannot be produced using the conventional processing techniques. 3D printing has recently emerged as an advanced processing technology that enables the processing of biomaterials into 3D porous scaffolds with highly complex architectures and tunable shapes to precisely fit into irregular and complex tissue defects. 3D printing provides computer-based layer-by-layer additive manufacturing processes of highly precise and complex 3D structures with well-defined porosity and controlled mechanical properties in a highly reproducible manner. Furthermore, 3D printing technology provides an accurate patient-specific tissue defect model and enables the fabrication of a patient-specific tissue-engineered porous scaffold with pre-customized properties.     

Strategies for the chemical and biological functionalization of scaffolds for cardiac tissue engineering: a review

The development of biomaterials for cardiac tissue engineering (CTE) is challenging, primarily owing to the requirement of achieving a surface with favourable characteristics that enhances cell attachment and maturation. The biomaterial surface plays a crucial role as it forms the interface between the scaffold (or cardiac patch) and the cells. In the field of CTE, synthetic polymers (polyglycerol sebacate, polyethylene glycol, polyglycolic acid, poly-l-lactide, polyvinyl alcohol, polycaprolactone, polyurethanes and poly(N-isopropylacrylamide)) have been proven to exhibit suitable biodegradable and mechanical properties. Despite the fact that they show the required biocompatible behaviour, most synthetic polymers exhibit poor cell attachment capability. These synthetic polymers are mostly hydrophobic and lack cell recognition sites, limiting their application. Therefore, biofunctionalization of these biomaterials to enhance cell attachment and cell material interaction is being widely investigated. There are numerous approaches for functionalizing a material, which can be classified as mechanical, physical, chemical and biological. In this review, recent studies reported in the literature to functionalize scaffolds in the context of CTE, are discussed. Surface, morphological, chemical and biological modifications are introduced and the results of novel promising strategies and techniques are discussed.     

Microencapsulation of phosphogypsum into a sulfur polymer matrix: physico-chemical and radiological characterization

The aim of this work is to prepare a new type of phosphogypsum-sulfur polymer cements (PG-SPC) to be utilised in the manufacture of building materials. Physico-chemical and radiological characterization was performed in phosphogypsum and phosphogypsum-sulfur polymer concretes and modeling of exhalation rates has been also carried out. An optimized mixture of the materials was obtained, the solidified material with optimal mixture (sulfur/phosphogypsum = 1:0.9, phosphogypsum dosage = 10-40 wt.%) results in highest strength (54-62 MPa) and low total porosity (2.8-6.8%). The activity concentration index (I) in the PG-SPC is lower than the reference value in the most international regulations and; therefore, these cements can be used without radiological restrictions in the manufacture of building materials. Under normal conditions of ventilation, the contribution to the expected radon indoor concentration in a standard room is below the international recommendations, so the building materials studied in this work can be applied to houses built up under normal ventilation conditions.Additionally, and taking into account that the PG is enriched in several natural radionuclides as ²²⁶Ra, the leaching experiments have demonstrated that environmental impact of the using of SPCs cements with PG is negligible.     

Time-resolved vortex wake of a common swift flying over a range of flight speeds

The wake of a freely flying common swift (Apus apus L.) is examined in a wind tunnel at three different flight speeds, 5.7, 7.7 and 9.9 m s⁻¹. The wake of the bird is visualized using high-speed stereo digital particle image velocimetry (DPIV). Wake images are recorded in the transverse plane, perpendicular to the airflow. The wake of a swift has been studied previously using DPIV and recording wake images in the longitudinal plane, parallel to the airflow. The high-speed DPIV system allows for time-resolved wake sampling and the result shows features that were not discovered in the previous study, but there was approximately a 40 per cent vertical force deficit. As the earlier study also revealed, a pair of wingtip vortices are trailing behind the wingtips, but in addition, a pair of tail vortices and a pair of ‘wing root vortices’ are found that appear to originate from the wing/body junction. The existence of wing root vortices suggests that the two wings are not acting as a single wing, but are to some extent aerodynamically detached from each other. It is proposed that this is due to the body disrupting the lift distribution over the wing by generating less lift than the wings.     

Use of ultra-thin cross-linked polymer films for preparation of stable mono-dispersed carbon nanotubes

We report on the use of ultra-thin cross-linked polymer films to coat carbon nanotubes (CNTs). When n-dodecyl glyceryl itaconate, an amphiphilic monomer, and N,N'-methylenebis(acrylamide), a cross-linker, were mixed with CNTs, an ultra-thin cross-linked DGI polymer film formed on the surface of the individual CNTs by self-assembly polymerization. The CNTs modified with the cross-linked DGI polymer film are highly soluble in water with a multi-walled CNT concentration of up to 1 wt.%, providing an attractive approach for preparing stable, mono-dispersed CNT solutions.