Synthesis of nanocrystalline TiO<Subscript>2</Subscript>-coated coal fly ash for photocatalyst

In order to more easily separate TiO₂ photocatalyst from treated wastewater, TiO₂ photocatalyst is immobilized on coal fly ash by precipitation method. The titanium hydroxide precipitated on coal fly ash by neutralization of titanium chloride is transformed into titanium dioxide by heat treatment in the temperature range of 300–700 ‡C. The crystalline structure of the titanium dioxide shows anatase type in all ranges of heat treatment temperature. The crystal size of anatase increases with increasing heat treatment temperature, with the drawback being the lower removal ability of NO gas. When the coal fly ash coated with 10 wt% of TiO₂ was calcined at 300 and 400 ‡C for 2 hrs, the average crystal size of anatase appeared about 9 nm, and the removal rates of NO gas were 63 and 67.5%, respectively. The major iron oxide, existing in coal fly ash as impurity, is magnetite (Fe₃O₄). Phase transformation of magnetite into hematite (Fe₂O₃) by heat treatment improves the removal rate of NO gas for TiO₂-coated coal fly ash.     

Two novel hierarchical homogeneous nanoarchitectures of TiO<Subscript>2</Subscript> nanorods branched and P25-coated TiO<Subscript>2</Subscript> nanotube arrays and their photocurrent performances

We report here for the first time the synthesis of two novel hierarchical homogeneous nanoarchitectures of TiO₂ nanorods branched TiO₂ nanotube arrays (BTs) and P25-coated TiO₂ nanotube arrays (PCTs) using two-step method including electrochemical anodization and hydrothermal modification process. Then the photocurrent densities versus applied potentials of BTs, PCTs, and pure TiO₂ nanotube arrays (TNTAs) were investigated as well. Interestingly, at -0.11 V and under the same illumination condition, the photocurrent densities of BTs and PCTs show more than 1.5 and 1 times higher than that of pure TNTAs, respectively, which can be mainly attributed to significant improvement of the light-absorbing and charge-harvesting efficiency resulting from both larger and rougher surface areas of BTs and PCTs. Furthermore, these dramatic improvements suggest that BTs and PCTs will achieve better photoelectric conversion efficiency and become the promising candidates for applications in DSSCs, sensors, and photocatalysis.     

Influence of Tetraalkylammonium Compounds on Photocatalytic and Physical Properties of TiO<Subscript>2</Subscript>

A wide range of experimental data are reported for the first time on the TiO₂ prepared by hydrolysis of highly concentrated Ti(OⁱPr)₄ in water solutions of quaternary ammonium compounds (QACs). These TiO₂ materials have been shown to be photocatalytically active under visible light irradiation (LED, 450 nm) using acetone as a model substrate oxidized in the gas phase. Five-fold increase in activity in comparison with the commercial photocatalyst KRONOClean 7000 is achieved. Colloidal solutions of hydrolyzed Ti(OⁱPr)₄ have been studied by SAXS method suggesting the way in which QACs solutions may influence the final composition of TiO₂. Phase composition, morphology, texture and surface properties of the modified TiO₂ have been studied using XRD, BET, SEM and low-temperature FTIR with CO probe. The surface elemental composition has been investigated by XPS method. Additional low-energy levels and high concentration of acid surface sites originated from N/C-doping, are likely to be the main reasons for exceptional photocatalytic performance of these samples.

Graphical Abstract

Open image in new window

     

Al-doped TiO<Subscript>2</Subscript> mesoporous materials: synthesis and photodegradation properties

Aluminium-doped TiO₂ mesoporous material was successfully fabricated by solid-state reaction with cetyltrimethylammonium bromide as a template agent and tetrabutyl orthotitanate as a precursor. The characteristic results from low-angle and wide-angle X-ray diffraction, high resolution transmission electron microscopy and energy dispersive spectroscopy, N₂ absorption–desorption, Fourier transform infrared spectroscopy, Raman spectroscopy, ultraviolet visible light spectroscopy and X-ray photoelectron spectroscopy (XPS) clearly showed that the mesoporous architecture of aluminium-doped TiO₂ was composed of crystal wall and micro-/mesopore formed gradually by the mesopore degradation of anatase TiO₂, and aluminium had been doped into the framework of anatase TiO₂. The mesoporous Al-doped TiO₂ material, not only possessed high thermal stability hexahedral mesostructure, large BET surface area and narrow distribution of pore size, but also showed excellent photodegradation behavior for Congo Red. Furthermore the medium UV–Vis absorption peak of mesoporous aluminium-doped TiO₂ in the range 210–370 nm was the absorption peak of aluminium oxide nanoparticles locating the extraframework of TiO₂. A small quantity of aluminium doped into anatase TiO₂ could obviously improve photodegradation activity, and the photodegradation activity of aluminium-doped TiO₂ was higher than that of pure TiO₂.     

Photocatalytic Generation of H<Subscript>2</Subscript> Gas from Neat Ethanol over Pt/TiO<Subscript>2</Subscript> Nanotube Catalysts

TiO₂ nanotubes promoted with Pt metal were prepared and tested to be the photocatalytic dehydrogenation catalyst in neat ethanol for producing H₂ gas (C₂H₅OHC₃CHO +H₂). It was found that the ability to produce H₂, the liquid phase product distribution and the catlyst stability of these promoted nano catalysts all depended on the Pt loading and catalyst preparation procedure. These Pt/TiO₂ catalysts with TiO₂ nanotubes washed with diluted H₂SO₄ solution produced 1, 2-diethoxy ethane (acetal) as the major liquid phase product, while over those washed with diluted HCl solution or H₂O, acetaldehyde was the major liquid phase product.     

Phase evolution during mechanochemical coreduction of V<Subscript>2</Subscript>O<Subscript>5</Subscript> and TiO<Subscript>2</Subscript> with A

The direct preparation of V-Ti solid solution alloy by coreduction of V₂O₅ and TiO₂ with Al in an attritor mill was investigated. The reduction of V₂O₅ with Al is highly exothermic, whereas reduction of TiO₂ with Al is not sufficiently exothermic for a self-sustaining reaction. A range of compositions of a mixture of V₂O₅ and TiO₂ can be so chosen as to make the overall reduction of V₂O₅ and TiO₂ with Al sufficiently exothermic for a self-sustaining reaction. Initial studies were done to identify the reaction products obtained by reducing V₂O₅ with Al. The reaction yielded the intermetallic phase (Al₃V), V, and Al₂O₃. SEM images indicated melting and solidification of the phases, leading to agglomeration. Further experiments involved mixing appropriate amounts of TiO₂ with V₂O₅ and reducing the mixture with Al. XRD data for products showed the presence of V, V₅Al₈, and Al₂O₃. X-Ray Florescence (XRF) analysis and energy dispersive analyzer (EDAX) of SEM sample images indicated the formation of V-Ti solid solution. Microstructure of the milled charges taken out prior to reaction initiation indicated morphology change in Al powder and agglomeration/segregation of reactants. As a result, the reaction of V₂O₅ with the excess Al at certain regions also promoted the formation of vanadium aluminide.     

Effect of TiO<Subscript>2</Subscript> loading on the activity of V/TiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in the catalytic oxidehydrogenation of ethylbenzene with carbon dioxide

TiO₂-Al₂O₃ mixed oxides with different compositions ranging from 40wt-% to 95wt-% of TiO₂ were prepared by sol-gel method and impregnated with different amounts of VO _x . Supports and catalysts were characterized by X-ray diffraction (XRD), physisorption, temperature preprogrammed reduction (H₂-TPR), and ammonia temperature programmed desorption (NH₃-TPD). TiO₂ content in the support had obvious effect on the crystal structure, texture characteristic, acid property, and catalytic activity in dehydrogenation of ethylbenzene (EB) with carbon dioxide. The highest catalytic activity was acquired when the TiO₂ content was 50 wt-%.     

Dye sensitized CO<Subscript>2</Subscript> reduction over pure and platinized TiO<Subscript>2</Subscript>

TiO₂ thin and thick films promoted with platinum and organic sensitizers including novel perylene diimide dyes (PDI) were prepared and tested for carbon dioxide reduction with water under visible light. TiO₂ films were prepared by a dip coating sol–gel technique. Pt was incorporated on TiO₂ surface by wet impregnation [Pt(on).TiO₂], or in the TiO₂ film [Pt(in).TiO₂] by adding the precursor in the sol. When tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate was used as sensitizer, in addition to visible light activity towards methane production, H₂ evolution was also observed. Perylene diimide derivatives used in this study have shown light harvesting capability similar to the tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate.     

Degradation kinetics of recalcitrant organic compounds in a decontamination process with UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> and UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> processes

In this study, degradation aspects and kinetics of organics in a decontamination process were considered in the degradation experiments of advanced oxidation processes (AOP),i.e., UV, UV/H₂O, and UV/H₂O,/TiO₂ systems. In the oxalic acid degradation with different H₂O₂ concentrations, it was found that oxalic acid was degraded with the first order reaction and the highest degradation rate was observed at 0.1 M of hydrogen peroxide. Degradation rate of oxalic acid was much higher than that of citric acid, irrespective of degradation methods, assuming that degradation aspects are related to chemical structures. Of methods, the TiO₂ mediated photocatalysis showed the highest rate constant for oxalic acid and citric acid degradation. It was clearly showed that advanced oxidation processes were effective means to degrade recalcitrant organic compounds existing in a decontamination process.     

Adsorption of thallium cations on RuO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript> electrodes

The electrochemical ion-exchange properties of RuO₂–TiO₂ film electrodes with different composition have been studied in acidic and alkaline media. Thallium-cation uptake has been observed only from the latter and its extent was found to be a function of electrode potential and composition. At potentials near 0.0 V (RHE), the amount of adsorbed Tl⁺ exhibited a maximum, and decreased with increasing potential, reaching a broad minimum in the range 0.4–0.8 V. A further increase in the electrode potential, above about 1.0 V, led to an increase of adsorbed thallium species, essentially due to deposition of a few layers of Tl(III) hydroxide. In fact, the release of the latter species was found to be much slower than that of thallium ions adsorbed at 0.0 V. For the latter, in turn, the double injection/ejection mechanism, currently accepted to explain the charge-storage in oxide electrodes, seems to be confirmed. The high Γ values attained at 0.0 V indicate that the large ionic radius of Tl⁺ does not prevent its diffusion through the thinner pore texture of the oxide coatings, possibly because of its poor hydration, related with lower charge density at the ion surfaces.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Gas-phase Photocatalytic Oxidation of Acrylonitrile on Sulphated TiO<Subscript>2</Subscript>: Continuous Flow and Transient Study

Abstract  

The gaseous products of photocatalytic oxidation (PCO) of acrylonitrile on sulphated P25 in concentrations from 10 to 100 ppm at 60 to 130 °C were CO₂, HCN and HNCO. This photocatalyst showed disproportionally improved performance at higher temperature and longer retention times. The temperature-programmed oxidation (TPO) after PCO disclosed possible reaction routes.     

Characterization of thermally aged AlPO<Subscript>4</Subscript>-coated LiCoO<Subscript>2</Subscript> thin films

The electrochemical properties and stability during storage of pristine and AlPO₄-coated LiCoO₂ thin films were characterized. The wide and smooth surface of the thin film electrode might provide an opportunity for one to observe surface reactions with an electrolyte. The rate capability and cyclic performance of the LiCoO₂ thin film were enhanced by AlPO₄ surface coating. Based on secondary ion mass spectrometry analysis and scanning electron microscopy images of the surface, it was confirmed that the coating layer was successfully protected from the reactive electrolyte during storage at 90°C. In contrast, the surface of the pristine sample was severely damaged after storage.     

Ni<Superscript>2+</Superscript> reduction under solar irradiation over CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/TiO<Subscript>2</Subscript> catalysts

The photo-electrochemical characterization of the hetero-system CoFe₂O₄/TiO₂ was undertaken for the Ni²⁺ reduction under solar light. The spinel CoFe₂O₄ was prepared by nitrate route at 940 °C and the optical gap (1.66 eV) was well matched to the sun spectrum. The flat band potential (-0.21 V_SCE) is more cathodic than the potential of Ni²⁺/Ni couple (-0.6 V_SCE), thus leading to a feasible nickel photoreduction. TiO₂ with a gap of 3.2 eV is used to mediate the electrons transfer. The reaction is achieved in batch configuration and is optimized with respect to Ni²⁺ concentration (30 ppm); a reduction percentage of 72% is obtained under sunlight, the Ni²⁺ reduction is strongly enhanced and follows a first order kinetic with a rate constant of 4.6×10^-2 min^-1 according to the Langmuir-Hinshelwood model.     

Application of ZnO and TiO<Subscript>2</Subscript> nanoparticles coated onto montmorillonite in the presence of H<Subscript>2</Subscript>O<Subscript>2</Subscript> for efficient removal of cephalexin from aqueous solutions

This study considers the feasibility of uptake of cephalexin, an emerging contaminant, from aqueous solutions by using green local montmorillonite (GLM), montmorillonite coated with ZnO (ZnO/GLM) and montmorillonite coated with TiO₂ (TiO₂/GLM) in the presence of H₂O₂. Batch adsorption experiments were carried out as a function of pH, initial concentration of the cephalexin, adsorbent dosage, contact time, and temperature. Finally, the adsorbents were characterized by XRD, SEM and FTIR analyses. XRD patterns showed dramatic changes in the adsorbents after loading with the nanoparticles, confirming successful placing of the nanoparticles onto GLM. The GLM mineral surface after nanoparticle loading appears to be fully exposed and more porous with irregular shapes in particles diameters of 1-50 microns. FTIR analyses also confirmed dramatic changes in surface functional groups after modification with these nanoparticles. The results showed that the removal efficiency of cephalexin was better at lower pH values. Totally, the removal efficiency increased with increase in adsorbent dosage and contact time and decreased with concentration and temperature increase. The thermodynamics values of ΔG ^o and ΔH ^o revealed that the adsorption process was spontaneous and exothermic. In isotherm study, the maximum adsorption capacities (qm) were obtained to be 7.82, 17.09 and 49.26 mg/g for GLM, ZnO/GLM and TiO₂/GLM, respectively. Temkin constant (B _T ) showed that adsorption of cephalexin from solution was exothermic for all three adsorbents.     

Combustion of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Al thermit mixtures in steel tubes

Explored was the combustion of Fe₂O₃/TiO₂/Al thermit mixtures in steel tubes upon variation in green composition and with special emphasis on the dependence of combustion temperature T _c and burning velocity U on reaction heat Q. Special attention was given to incompleteness of combustion for compositions with low Q.