Efficient PDFA module using high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber

The highest reported single-pass gain coefficient of 0.36 dB/mW has been achieved using a newly developed Pr/sup 3+/-doped high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber, with a /spl Delta/n of 6.6%, a core diameter of 1.2 /spl mu/m and a transmission loss of 250 dB/km at 1.2 /spl mu/m. This fiber was used to construct an efficient PDFA module with a MOPA-LD. A small-signal net gain of 22.5 dB was achieved at 1.30 /spl mu/m with a pump power of 23m mW.     

Gain-flattened Er/sup 3+/-doped fiber amplifier for a WDM signal in the 1.57-1.60-/spl mu/m wavelength region

A gain-flattened Er/sup 3+/-doped silica-based fiber amplifier (EDFA) has been constructed for a 1.58-/spl mu/m band WDM signal. This EDFA exhibits uniform amplification characteristics with a gain excursion of 0.9 dB for a four-channel WDM signal in the 1.57-1.60 /spl mu/m wavelength region. The average signal gain and the noise figure for the WDM signal are 29.5 dB and less than 6.3 dB, respectively. The use of this EDFA in parallel with a 1.55-/spl mu/m band EDFA will expand the WDM transmission wavelength region.     

Germania-based core optical fibers

Germania-glass-based core silica glass cladding single-mode fibers (/spl Delta/n up to 0.143) with a minimum loss of 20 dB/km at 1.9 /spl mu/m were fabricated by the modified chemical vapor deposition (MCVD) method. The fibers exhibit strong photorefractivity with the type-IIa-induced refractive-index modulation of 2/spl times/10/sup -3/. The Raman gain of 300 to 59 dB/(km/spl middot/W) was determined at 1.07 to 1.6 /spl mu/m, respectively, in a 75 mol.% GeO/sub 2/ core fiber. Only 3 m of such fibers are enough for the creation of a 10-W Raman laser at 1.12 /spl mu/m with a 13-W pump at 1.07 /spl mu/m. Raman generation in optical fiber at a wavelength of 2.2 /spl mu/m was obtained for the first time.     

Midinfrared holmium fiber lasers

The use of the high-power Tm/sup 3+/-doped silica fiber laser as a pump source for Ho/sup 3+/-doped silica and Ho/sup 3+/-doped fluoride fiber lasers for the generation of 2.1-/spl mu/m radiation is demonstrated. The Ho/sup 3+/-doped silica fiber laser produced a maximum output power of 1.5 W at a slope efficiency of /spl sim/82%; one of the highest slope efficiencies measured for a fiber laser. In a nonoptimized but similar fiber laser arrangement, a Ho/sup 3+/-doped fluoride fiber laser produced an output power of 0.38 W at 2.08 /spl mu/m at a slope efficiency of /spl sim/50%. A Raman fiber laser operating at 1160 nm was also used to pump a Ho/sup 3+/-doped fluoride fiber laser operating at a wavelength of 2.86 /spl mu/m. An output power of 0.31W was produced at a slope efficiency of 10%. The energy transfer upconversion process that depopulates the lower laser level in this case operates at a higher efficiency when the pump wavelength is closer to the absorption peak of the /sup 5/I/sub 6/ energy level, however, this energy transfer process does not impede to a great extent the performance of the Ho/sup 3+/-doped fluoride fiber laser based on the /spl sim/2.1/spl mu/m laser transition.     

1.47 /spl mu/m Tm/sup 3+/:ZBLAN fibre laser pumped at 1.064 /spl mu/m

A large core area (1257 /spl mu/m/sup 2/) Tm/sup 3+/-doped ZBLAN fibre laser operated at 1.47 /spl mu/m is demonstrated. The pump source is a Nd:YAG laser operated at 1.064 /spl mu/m. A laser output power of 1.56 W continuous wave was obtained for 5.2 W of launched pump power. The slope efficiency with respect to the launched pump power was measured to be 33%.     

1.58-/spl mu/m broad-band erbium-doped tellurite fiber amplifier

This paper describes the development of a 1.58-/spl mu/m broad-band and gain-flattened erbium-doped tellurite fiber amplifier (EDTFA). First, we compare the spectroscopic properties of various glasses including the stimulated emission cross sections of the Er/sup 3+4/ I/sub 13/2/ /sup 4/I/sub 15/2/ transition and the signal excited-state absorption (ESA) cross sections of the Er/sup 3+4/ I/sub 13/2/ - /sup 4/I/sub 9/2/ transition. We detail the amplification characteristics of a 1.58-/spl mu/m-band EDTFA designed for wavelength-division-multiplexing applications by comparing it with a 1.58-/spl mu/m-band erbium-doped silica fiber amplifier. Furthermore, we describe the 1.58-/spl mu/m-band gain-flattened EDTFA we developed using a fiber-Bragg-grating-type gain equalizer. We achieved a gain of 25.3 dB and a noise figure of less than 6 dB with a slight gain excursion of 0.6 dB over a wide wavelength range of 1561-1611 nm. The total output power of the EDTFA module was 20.4 dBm and its power conversion efficiency reached 32.8%.     

Polarization independent bulk active region semiconductor optical amplifiers for 1.3 /spl mu/m wavelengths

Semiconductor optical amplifiers for 1.3 /spl mu/m are realized combining single-step grown bulk InGaAsP active region with ridge-waveguides. Achieved fiber-to-fiber gains are in excess of 27 dB with spectral ripples below 0.2 dB. Gain is polarization insensitive to within 1 dB over the entire range of driving current, 1.28 /spl mu/m to 1.34 /spl mu/m wavelength and 10/spl deg/C to 50/spl deg/C heat sink temperature. Intrinsic noise figure is 6.3 dB. Gain saturates at +10 dBm.     

35-dB gain Tm-doped ZBLYAN fiber amplifier operating at 1.65 /spl mu/m

We demonstrate the first high gain rare-earth-doped fiber amplifier operating at 1.65 /spl mu/m. It consists of ZBLYAN fiber with a Tm/sup 3+/-doped core and Tb/sup 3+/-doped cladding, pumped by 1.22 /spl mu/m laser diodes. It is possible to achieve efficient amplification with Tm/sup 3+/ ions if their amplified spontaneous emission (ASE) in the 1.75 to 2.0 /spl mu/m wavelength region is suppressed by doping Tb/sup 3+/ ions in the cladding. A two-stage-type fiber amplifier is constructed and a signal gain of 35 dB is achieved for a pump power of 140 mW. A gain over 25 dB is realized in the 1.65 /spl mu/m to 1.67 /spl mu/m wavelength region.     

Measurement of far-infrared laser frequencies from optically pumped CHD/sub 2/OH

A three-laser heterodyne system was used to frequency measure 11 previously observed optically pumped far-infrared (FIR) laser emissions of CHD/sub 2/OH. These newly measured frequencies have fractional uncertainties of /spl plusmn/2/spl times/10/sup -7/ and correspond to laser wavelengths ranging from 47.8 to 238.0 /spl mu/m. The pump laser offset frequency was measured for 15 CHD/sub 2/OH FIR laser emissions.     

Plug-in type 1.3-/spl mu/m fiber amplifier module for rack-mounted shelves

We have successfully developed a plug-in type PDFA module for rack mounted shelves which is assembled on a printed-board. In this module, we use a newly developed Pr/sup 3+/-doped high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber and wavelength stabilized 1.017-/spl mu/m laser diodes (LDs). We have obtained a small-signal gain of 24 dB and a noise figure of 6.6 dB at 1.30 /spl mu/m with an LD drive current of 240 mA/spl times/2. We achieved an output power of 10 dBm with a signal input power of 0 dBm. The total power consumption of this module, including that of a Peltier cooler, was 3.5 W when the LD drive current was 240 mA/spl times/2.     

Amplification and lasing at 1.3 mu m in praseodymium-doped fluorozirconate fibres

Light emission from the /sup 1/G/sub 4/ to /sup 3/H/sub 5/ transition around 1.3 mu m of Pr/sup 3+/ has been studied in fluoride glass (ZBLAN) fibres. Pumping at 1064 nm yields extracted laser power of a few mW at 1.294 mu m. Gain curves centred at 1.295 mu m have been obtained, with gross gains of more than 15 dB at 1.319 mu m. Changes of the output ASE with pumping conditions are explained by excited state absorption or energy transfer from the /sup 1/G/sub 4/ upper level of the transition.<>     

1.65 /spl mu/m-band optical amplification with Er/sup 3+/-doped fluorozirconate fibre using 0.8 /spl mu/m upconversion pumping

In order to expand the available bandwidth for wavelength division multiplexing transmission systems, a 1.65 /spl mu/m-band optical fibre amplifier with Er/sup 3+/-doped fluorozirconate fibre using 0.8 /spl mu/m upconversion pumping has been demonstrated. The positive gain, 3.8 dB, is the first ever achieved by means of (/sup 2/H/sub 11/2/, /sup 4/S/sub 3/2/) /spl rarr/ /sup 4/I/sub 9/2/ stimulated emission transition.     

30-GHz-band over 5-W power performance of short-channel AlGaN/GaN heterojunction FETs

This paper describes the small-signal characterization through delay-time analysis and high-power operation of the Ka-band of AlGaN/GaN heterojunction field-effect transistors (FETs). An FET with a gatewidth of 100 /spl mu/m and a gate length of 0.09 /spl mu/m has exhibited a current gain cutoff frequency (f/sub T/) of 81 GHz, a maximum frequency of oscillation (fmax) of 187 GHz, and a maximum stable gain of 10.5 dB at 30 GHz (8.3 dB at 60 GHz). Delay-time analysis has demonstrated channel electron velocities of 1.50/spl times/10/sup 7/ to 1.75/spl times/10/sup 7/ cm/s in a gate-length range of 0.09-0.25 /spl mu/m. State-of-the-art performance-saturated power of 5.8 W with a linear gain of 9.2 dB and a power-added efficiency of 43.2%-has been achieved at 30 GHz using a single chip having a gatewidth of 1.0 mm and a gate length of 0.25 /spl mu/m.     

Analysis of heat generation and thermal lensing in erbium 3-/spl mu/m lasers

The influence of energy-transfer upconversion (ETU) between neighboring ions in the upper and lower laser levels of erbium 3-/spl mu/m continuous-wave lasers on heat generation and thermal lensing is investigated. It is shown that the multiphonon relaxations following each ETU process generate significant heat dissipation in the crystal. This undesired effect is an unavoidable consequence of the efficient energy recycling by ETU in erbium 3-/spl mu/m crystal lasers, but is further enhanced under nonlasing conditions. Similar mechanisms may affect future erbium 3-/spl mu/m fiber lasers. In a three-dimensional finite-element calculation, excitation densities, upconversion rates, heat generation, temperature profiles, and thermal lensing are calculated for a LiYF/sub 4/:Er/sup 3+/ 3-/spl mu/m laser. In the chosen example, the fraction of the absorbed pump power converted to heat is 40% under lasing and 72% under nonlasing conditions. The heat generation in a LiYF/sub 4/:Er/sup 3+/ 3-/spl mu/m laser is 1.7 and the thermal-lens power up to 2.2 times larger than in a LiYF/sub 4/:Nd/sup 3+/ 1-/spl mu/m laser under equivalent pump conditions, thus, also putting a higher risk of rod fracture on the erbium system.     

A 1.8-V 10-Gb/s fully integrated CMOS optical receiver analog front-end

A fully integrated 10-Gb/s optical receiver analog front-end (AFE) design that includes a transimpedance amplifier (TIA) and a limiting amplifier (LA) is demonstrated to require less chip area and is suitable for both low-cost and low-voltage applications. The AFE is fabricated using a 0.18-/spl mu/m CMOS technology. The tiny photo current received by the receiver AFE is amplified to a differential voltage swing of 400 mV/sub (pp)/. In order to avoid off-chip noise interference, the TIA and LA are dc-coupled on the chip instead of ac-coupled though a large external capacitor. The receiver front-end provides a conversion gain of up to 87 dB/spl Omega/ and -3dB bandwidth of 7.6 GHz. The measured sensitivity of the optical receiver is -12dBm at a bit-error rate of 10/sup -12/ with a 2/sup 31/-1 pseudorandom test pattern. Three-dimensional symmetric transformers are utilized in the AFE design for bandwidth enhancement. Operating under a 1.8-V supply, the power dissipation is 210 mW, and the chip size is 1028 /spl mu/m/spl times/1796 /spl mu/m.     

Microwave noise performance of AlGaN-GaN HEMTs with small DC power dissipation

We report low microwave noise performance of discrete AlGaN-GaN HEMTs at DC power dissipation comparable to that of GaAs-based low-noise FETs. At 1-V source-drain (SD) bias and DC power dissipation of 97 mW/mm, minimum noise figures (NF/sub min/) of 0.75 dB at 10 GHz and 1.5 dB at 20 GHz were achieved, respectively. A device breakdown voltage of 40 V was observed. Both the low microwave noise performance at small DC power level and high breakdown voltage was obtained with a shorter SD spacing of 1.5 /spl mu/m in 0.15-/spl mu/m gate length GaN HEMTs. By comparison, NF/sub min/ with 2 /spl mu/m SD spacing was 0.2 dB greater at 10 GHz.     

Long-wavelength In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As large-area avalanche photodiodes and arrays

Large-area (500-/spl mu/m diameter) mesa-structure In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As avalanche photodiodes (APDs) are reported. The dark current density was /spl sim/2.5/spl times/10/sup -2/ nA//spl mu/m/sup 2/ at 90% of breakdown; low surface leakage current density (/spl sim/4.2 pA//spl mu/m) was achieved with wet chemical etching and SiO/sub 2/ passivation. An 18 /spl times/ 18 APD array with uniform distributions of breakdown voltage, dark current, and multiplication gain has also been demonstrated. The APDs in the array achieved 3-dB bandwidth of /spl sim/8 GHz at low gain and a gain-bandwidth product of /spl sim/120 GHz.     

High-T/sub 0/ strain-compensated InGaAsSb-AlGaAsSb quantum-well lasers emitting at 2.43 /spl mu/m

Strain-compensated InGaAsSb-AlGaAsSb quantum-well (QW) lasers emitting near 2.5 /spl mu/m have been grown by solid-source molecular beam epitaxy. The relatively high arsenic composition causing a tensile strain in the Al/sub 0.25/GaAs/sub 0.08/Sb barriers lowers the valence band edge and the hole energy level, leading to an increased hole confinement and improved laser performance. A 60% external differential efficiency in pulsed mode was achieved for 1000-/spl mu/m-long lasers emitting at 2.43 /spl mu/m. A characteristic temperature T/sub 0/ as high as 163 K and a lasing-wavelength temperature dependence of 1.02 nm//spl deg/C were obtained at room temperature. For 2000 /spl times/ 200 /spl mu/m/sup 2/ broad-area three-QW lasers without lateral current confinement, a low pulsed threshold of 275 A/cm/sup 2/ was measured.     

A CMOS voltage reference based on weighted /spl Delta/V/sub GS/ for CMOS low-dropout linear regulators

A CMOS voltage reference, which is based on the weighted difference of the gate-source voltages of an NMOST and a PMOST operating in saturation region, is presented. The voltage reference is designed for CMOS low-dropout linear regulators and has been implemented in a standard 0.6-/spl mu/m CMOS technology (V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C). The occupied chip area is 0.055 mm/sup 2/. The minimum supply voltage is 1.4 V, and the maximum supply current is 9.7 /spl mu/A. A typical mean uncalibrated temperature coefficient of 36.9 ppm//spl deg/C is achieved, and the typical mean line regulation is /spl plusmn/0.083%/V. The power-supply rejection ratio without any filtering capacitor at 100 Hz and 10 MHz are -47 and -20 dB, respectively. Moreover, the measured noise density with a 100-nF filtering capacitor at 100 Hz is 152 nV//spl radic/(Hz) and that at 100 kHz is 1.6 nV//spl radic/(Hz).     

Silica-clad neodymium-doped lanthanum phosphate fibers and fiber lasers

We have fabricated a neodymium-doped phosphate glass fiber with a silica cladding and used it to form a fiber laser. Phosphate and silicate glasses have considerably different glass transition temperatures and softening points making it hard to draw a fiber from these two glasses. A bulk phosphate glass of composition (Nd/sub 2/O/sub 3/)/sub 0.011/(La/sub 2/O/sub 3/)/sub 0.259/(P/sub 2/O/sub 5/)/sub 0.725/(Al/sub 2/O/sub 3/)/sub 0.005/ was prepared and the resultant material was transparent, free from bubbles and visibly homogeneous. The bulk phosphate glass was drawn to a fiber while being jacketed with silica and the resultant structure was of good optical quality, free from air bubbles and major defects. The attenuation at a wavelength of 1.06 /spl mu/m was 0.05 dB/cm and the refractive index of the core and cladding at the pump wavelength of 488 nm was 1.56 and 1.46, respectively. The fibers were mechanically strong enough to allow for ease of handling and could be spliced to conventional silica fiber. The fibers were used to demonstrate lasing at the /sup 4/F/sub 3/2/-/sup 4/I/sub 11/2/ (1.06 /spl mu/m) transition. Our work demonstrates the potential to form silica clad optical fibers with phosphate cores doped with very high levels of rare-earth ions (27-mol % rare-earth oxide).