The effect of solder bump pitch on the underfill flow

An underfill encapsulant was used to fill the gap between the chip and substrate around solder joints to improve the long-term reliability of flip chip interconnect systems. The underfill encapsulant was filled by the capillary effect. In this study, the filling time and pattern of the underfill flow in the process with different bumping pitch, bump diameter, and gap size were investigated. A modified Hele-Shaw flow model, that considered the flow resistance in both the thickness direction and the restrictions between solder bumps, was used. This model estimated the flow resistance induced by the chip and substrate as well as the solder bumps, and provided a reasonable flow front prediction. A modified model that considered the effect of fine pitch solder bumps was also proposed to estimate the capillary force in fine pitch arrangements. It was found that, on a full array solder bump pattern, the filling flow was actually faster for fine pitch bumps in some arrangements. The filling time of the underfill process depends on the parameters of bumping pitch, bump diameter, and gap size. A proposed capillary force parameter can provide information on bump pattern design for facilitating the underfilling process.     

焊球植球凸块工艺的可靠性研究

焊球植球是一种最具潜力的低成本倒装芯片凸块制作工艺.采用焊球植球工艺制作的晶圆级芯片尺寸封装芯片的凸块与芯片表面连接的可靠性问题是此类封装技术研究的重点.为此,参考JEDEC关于电子封装相关标准,建立了检验由焊球植球工艺生产的晶圆级芯片尺寸封装芯片凸块与芯片连接及凸块本身是否可靠的可靠性测试方法与判断标准.由焊球植球工艺生产的晶圆级芯片尺寸封装芯片,分别采用高温存储、热循环和多次回流进行试验,然后利用扫描电子显微镜检查芯片上凸块剖面的凸块下金属层分布和测试凸块推力大小来验证凸块的可靠性.试验数据表明焊球植球工艺生产的晶圆级芯片尺寸封装芯片具有高的封装连接可靠性.     

Experimental characterization and mechanical behavior analysis of intermetallic compounds of Sn–3.5Ag lead-free solder bump with Ti/Cu/Ni UBM on copper chip

Due to today’s trend towards ‘green’ products, the environmentally conscious manufacturers are moving toward lead-free schemes for electronic devices and components. Nowadays the bumping process has become a branch of the infrastructure of flip chip bonding technology. However, the formation of excessively brittle intermetallic compound (IMC) between under bump metallurgy (UBM)/solder bump interface influences the strength of solder bumps within flip chips, and may create a package reliability issue. Based on the above reason, this study investigated the mechanical behavior of lead-free solder bumps affected by the solder/UBM IMC formation in the duration of isothermal aging. To attain the objective, the test vehicles of Sn–Ag (lead-free) and Sn–Pb solder bump systems designed in different solder volumes as well as UBM diameters were used to experimentally characterize their mechanical behavior. It is worth to mention that, to study the IMC growth mechanism and the mechanical behavior of a electroplated solder bump on a Ti/Cu/Ni UBM layer fabricated on a copper chip, the test vehicles are composed of, from bottom to top, a copper metal pad on silicon substrate, a Ti/Cu/Ni UBM layer and electroplated solder bumps. By way of metallurgical microscope and scanning-electron-microscope (SEM) observation, the interfacial microstructure of test vehicles was measured and analyzed. In addition, a bump shear test was utilized to determine the strength of solder bumps. Different shear displacement rates were selected to study the time-dependent failure mechanism of the solder bumps. The results indicated that after isothermal aging treatment at 150 °C for over 1000 h, the Sn–Ag solder revealed a better maintenance of bump strength than that of the Sn–Pb solder, and the Sn–Pb solder showed a higher IMC growth rate than that of Sn–Ag solder. In addition, it was concluded that the test vehicles of copper chip with the selected Ti/Cu/Ni UBMs showed good bump strength in both the Sn–Ag and Sn–Pb systems as the IMC grows. Furthermore, the study of shear displacement rate effect on the solder bump strength indicates that the analysis of bump strength versus thermal aging time should be identified as a qualitative analysis for solder bump strength determination rather than a quantitative one. In terms of the solder bump volume and the UBM size effects, neither the Sn–Ag nor the Sn–Pb solders showed any significant effect on the IMC growth rate.     

Thermomechanical Reliability Study of Flip Chip Solder Bumps: Using Laser Ultrasound Technique and Finite Element Method

Current techniques for nondestructive quality evaluation of solder bumps in electronic packages are either incapable of detecting solder bump cracks, or unsuitable for in-line inspection due to high cost and low throughput. As an alternative, a solder bump inspection system is being developed at Georgia Institute of Technology using laser ultrasound and interferometric techniques . This system uses a pulsed Nd:YAG laser to induce ultrasound in electronic packages in the thermoelastic regime; it then measures the transient out-of-plane displacement responses on the package surfaces using laser interferometric technique. The quality of solder bumps in electronic packages is evaluated by analyzing the transient responses. This paper presents a systematic study on thermomechanical reliability of flip chip solder bumps using laser ultrasound–interferometric inspection technique and finite element (FE) method. The correlation between the failure parameter extracted from FE simulation for evaluating solder bump reliability and quality degradation characterization of solder bumps through noncontact, nondestructive laser ultrasound testing has also been investigated.      

Effects of pre-bump probing and bumping processes on eutectic solder bump electromigration

This paper investigates the electromigration reliability of flip chip packages with and without pre-bump wafer probing via high temperature operation life test (HTOL) using printed and electroplated bumps. Under bump metallization (UBM) of printed and electroplated bumps is a thin film of Al/Ni(V)/Cu and Ti/Cu/Ni, respectively, while the bump material consists of eutectic Sn/Pb solder. Current densities from 7380 to 20 100 A/cm² and ambient temperatures at 100, 125 and 150 °C are applied in order to study their impact on electromigration. The results reveal that the bump temperature has a higher influence than the current density when it comes to bump failures. The observed interconnect damage is from bumps with electrical current flowing upward into the UBM/bump interface (cathode). Identified failure sites and modes reveal structural damage at the region of the UBM and UBM/bump interface, in the form of solder voiding and cracking. The effects of current polarity, current crowding, and operation temperature are key factors to electromigration failures of flip chip packaging. The maximum allowable current density of the electroplated bumps is superior to the printed bumps by a factor of 3.0–3.7 times. Besides, the median time to failure (MTTF) of without-underfill packaging is preferred to that of with-underfill packaging by 1.5–2.2 times. Furthermore, the differences in MTTF between pre-bump and without pre-bump probing procedures are 2.0–19.4% and 1.6–10.3% for printed and electroplated bumps, respectively.     

Design, assembly and reliability of large die and fine-pitch Cu/low-k flip chip package

This paper reports the design, assembly and reliability assessment of 21 × 21 mm² Cu/low-k flip chip (65 nm node) with 150 μm bump pitch and high bump density. To reduce the stress from the solder bump pad to low-k layers, Metal Redistribution Layer (RDL) and Polymer Encapsulated Dicing Lane (PEDL) are applied to the Cu/low-k wafer. Lead-free Sn2.5Ag, high-lead Pb5Sn and Cu-post/Sn37Pb bumps are evaluated as the first-level interconnects. It is found that the flip chip assembly of high-lead bumped test vehicle requires the right choice of flux and good alignment between the high-lead solder bumps and substrate pre-solder alloy to ensure proper solder bump and substrate pre-solder alloy wetting. Joint Electron Device Engineering Council (JEDEC) standard reliability is performed on the test vehicle with different first-level interconnects, underfill materials and PEDL.By integrating PEDL to the Cu/low-k chip, the reliability performance of the flip chip package has been improved by almost two times. This paper has demonstrated Moisture Sensitivity Test-Level 2 (MST-L2) qualified large die and fine-pitch Cu/low-k flip chip package. The presented results are significant for the development of flip chip packaging technologies for future advanced Cu/low-k generations.     

Interfacial reaction and joint reliability of fine-pitch flip-chip solder bump using stencil printing method

This study was focused on the formation and reliability evaluation of solder joints with different diameters and pitches for flip chip applications. We investigated the interfacial reaction and shear strength between two different solders (Sn-37Pb and Sn-3.0Ag-0.5Cu, in wt.%) and ENIG (Electroless Nickel Immersion Gold) UBM (Under Bump Metallurgy) during multiple reflow. Firstly, we formed the flip chip solder bumps on the Ti/Cu/ENIG metallized Si wafer using a stencil printing method. After reflow, the average solder bump diameters were about 130, 160 and 190 μm, respectively. After multiple reflows, Ni₃Sn₄ intermetallic compound (IMC) layer formed at the Sn-37Pb solder/ENIG UBM interface. On the other hand, in the case of Sn-3.0Ag-0.5Cu solder, (Cu,Ni)₆Sn₅ and (Ni,Cu)₃Sn₄ IMCs were formed at the interface. The shear force of the Pb-free Sn-3.0Ag-0.5Cu flip chip solder bump was higher than that of the conventional Sn-37Pb flip chip solder bump.     

Investigation of flip chip under bump metallization systems of Cupads

In this study, UBM material systems for flip chip solder bumps on Cu pads were investigated using the electroless copper (E-Cu) and electroless nickel (E-Ni) plating methods; and the effects of the interfacial reaction between UBMs and Sn-36Pb-2Ag solders on the solder bump joint reliability were also investigated to optimize UBM materials for flip chip on Cu pads. For the E-Cu UBM, scallop-like Cu₆Sn₅, intermetallic compound (IMC) forms at the solder/E-Cu interface, and bump fracture occurred along this interface under a relatively small load. In contrast, at the E-Ni/E-Cu UBM, E-Ni serves as a good diffusion-barrier layer. The E-Ni effectively limited the growth of the IMC at the interface, and the polygonal-shape Ni₃ Sn₄ IMC resulted in a relatively higher adhesion strength compared with the E-Cu UBM. As a result, electroless deposited UBM systems were successfully demonstrated as low cost UBM alternatives on Cu pads. It was found that the E-Ni/E-Cu UBM material system was a better choice for solder flip chip interconnection on Cu pads than the E-Cu UBM     

Low cost bumping by stencil printing: process qualification for 200 μm pitch

Area array packages (flip chip, CSP (Chip scale packages) and BGA) require the formation of bumps for the board assembly. Since the established bumping methods need expensive equipment and/or are limited by the throughput, minimal pitch and yield, the industry is currently searching for new and lower cost bumping approaches. The experimental work of stencil printing to create solder bumps for flip chip devices is described in detail in this article. In the first part of this article, a low cost wafer bumping process for flip chip applications will be studied in particular. The process is based on an electroless nickel under bump metallization and solder bumping by stencil printing. The experimental results for this technology will be presented, and the limits concerning pitch, stencil design, reproducibility and bump height will be discussed in detail. In the second part, a comparison of measured standard deviations of bump heights as well as the quality demands for ultrafine pitch flip chip assembly are shown.     

Influence of solder bump arrangements on molded IC encapsulation

This paper presents a fluid–structure interaction (FSI) analysis of ball grid array (BGA) package encapsulation. Real-time and simultaneous FSI analysis is conducted by using finite volume code (FLUENT) and finite element code (ABAQUS), which are coupled with MpCCI. A BGA integrated circuit (IC) package with different solder bump arrangements is considered in this study. In the FSI analysis, effects of solder bump arrangements on pressure distribution, void, deformation, and stress imposed on the IC structures are investigated. The maximum deformation and maximum stress on the silicon chip and solder bumps are evaluated. The findings indicate that the full-array solder bump package encounters lower stress and deformation during encapsulation. The void formation of each solder bump arrangement is examined. Scaled-up encapsulation is performed and the predicted flow front advancements are substantiated by experimental results. Results demonstrate the excellent capability of the proposed modeling tools for predictive trends of IC encapsulation. Thus, better understanding of IC encapsulation is provided to engineers and package designers in the microelectronics industry.     

Double bump flip-chip assembly

Capillary underfill remains the dominate process for underfilling Hip-chip die both in packages and for direct chip attach (DCA) on printed circuit board (PCB) assemblies. Capillary underfill requires a post reflow dispense and cure operation, and the underflow time increases with increasing die area and decreasing die-to-substrate spacing. Fluxing or no-How underfills are dispensed prior to die placement and cure during the solder reflow cycle. Since filler particles in the fluxing underfill can be trapped between the solder ball and the substrate pad during placement, the filler content of fluxing underfills is typically limited to <20% or assembly yield drops dramatically. At 20% filler concentration, the coefficient of thermal expansion (CTE) of the underfill is near that of the bulk resin (50-80 ppm//spl deg/C). In this paper, a double bump Hip-chip process is described. A filled capillary underfill is coated onto a wafer and cured. The wafer is then polished to expose the solder bumps. A second solder bump is formed over the original bump by stencil printing solder paste. After dicing, the die is assembled to the PCB using unfilled fluxing underfill. In the resulting structure, the low CTE underfill is near the low CTE Si die, and the higher CTE underfill is in contact with the PCB. In addition, the standoff height is increased compared to a conventional single bump assembly. In air-to-air thermal shock tests, the double bump assembly was /spl sim/ 1.5 X more reliable than the conventional single bump construction with fluxing underfill. Modeling results are also presented.     

Reliability investigations of hard core solder bumps using mechanical palladium bumps and SnPb solder

The choice of solder joint metallurgy is a key issue especially for the reliability of flip-chip assemblies. Besides the metallurgical systems already widely used and well understood, new materials are emerging as solderable under bump metallization (UBM). For single chip bumping Pd stud bumps form a solid core under the solder layer. These hard core solder bumps are an adequate solution if single dies are available only and the chosen assembly technology is flip chip soldering. The scope of this paper is to summarize the results from aging of lead/tin solder bumps on palladium. The growth of intermetallic and its impact on the mechanical reliability are investigated.     

MECHATRONICS 2000. Seventh Mechatronics Forum InternationalConference and Mechatronics Education Workshop

The following topics are dealt with: flip chip solder joint quality inspection; direct chip attach packaging for microsystems; reliability analysis of no-underfill flip chip package; ASIC/memory integration by system-on-package; wafer-level and flip chip designs through solder prediction models and validation; reliability evaluation of under bump metallurgy in two solder systems; a method to improve the efficiency of the CMP process; thermal and reliability analysis of packaging systems     

Bump formation for flip chip and CSP by solder paste printing

Area array packages (flip chip, CSP and BGA) require the formation of bumps for the board assembly. Since the established bumping methods need expensive equipment or are limited by the throughput, minimal pitch and yield the industry is currently searching for new and lower cost bumping approaches. In this paper the experimental work of stencil printing to create solder bumps for flip chip and wafer level CSP (CSP-WL) is described in detail.This paper is divided into two parts. In the first part of the paper a low cost wafer bumping process for flip chip applications will be studied in particular. The process is based on an electroless Nickel under bump metallization and solder bumping by stencil printing. The experimental results for this technology will be presented and the limits concerning pitch, reproducibility and bump height will be discussed in detail. The second part of the paper is focused on solder paste printing for wafer-level CSPs. In order to achieve large bumps an optimized printing method will be presented. Additionally advanced stencil design will be shown and the achieved results will be compared with conventional methods.     

Flip chip interconnect systems using copper wire stud bump and leadfree solder

This research focuses on flip chip interconnect systems consisting of wire stud bumps and solder alloy interconnects. Conventional gold (Au) wire stud bumps and new copper (Cu) wire stud bumps were formed on the chip by wire stud bumping. Cu wire studs were bumped by controlling the ramp rate of ultrasonic power to eliminate the occurrence of under-pad chip cracks that tend to occur with high strength bonding wire. Lead free 96Sn3.5Ag0.5Cu (SnAgCu) alloy was used to interconnect the wire studs and printed circuit board. A comparison was made with conventional eutectic 63Sn37Pb (SnPb) alloy and 60In40Pb (InPb) alloy. Test vehicles were assembled with two different direct chip attachment (DCA) processes. When the basic reflow assembly using a conventional pick and place machine and convection reflow was used, 30% of the lead free test vehicles exhibited process defects. Other lead free test vehicles failed quickly in thermal shock testing. Applying the basic reflow assembly process is detrimental for the SnAgCu test vehicles. On the other hand, when compression bonding assembly was performed using a high accuracy flip chip bonder, the lead free test vehicles exhibited no process defects and the thermal shock reliability improved. Cu stud-SnAgCu test vehicles (Cu-SnAgCu) in particular showed longer mean time to failure, 2269 cycles for the B stage process and 3237 cycles for high temperature bonding. The C-SAM and cross section analysis of the Cu stud bump assemblies indicated less delamination in thermal shock testing and significantly less Cu diffusion into the solder compared to Au stud bumped test vehicles. The Cu stud-SnAgCu systems form stable interconnects when assembled using a compression bonding process. Moreover, Cu wire stud bumping offers an acceptable solution for lead free assembly     

An overview of solder bump shape prediction algorithms withvalidations

The trend to reduce the size of electronic packages and develop increasingly sophisticated electronic devices with more, higher density inputs/outputs (I/Os), leads to the use of area array packages using chip scale packaging (CSP), flip chip (FC), and wafer level packaging (WLP) technologies. Greater attention has been paid to the reliability of solder joints and the assembly yield of the surface mounting process as use of advanced electronic packaging technologies has increased. The solder joint reliability has been observed to be highly dependent on solder joint geometry as well as solder material properties, such that predicting solder reflow shape became a critical issue for the electronic research community. In general, the truncated sphere method, the analytical solution and the energy-based algorithm are the three major methods for solder reflow geometry prediction. This research develops solder joint reliability design guidelines to accurately predict both the solder bump geometry and the standoff height for reflow soldered joints in area array packages. Three simulation methods such as truncated-sphere theory force-balanced analytical solution and energy-based approach for prediction of the solder bump geometry are each examined in detail, and the thermal enhanced BGA (TBGA) and flip chip packages are selected as the benchmark models to compare the simulation and experimental results. The simulation results indicate that all three methods can accurately predict the solder reflow shape in an accurate range     

Squeegee bump technology

An innovative solder bumping technology, termed squeegee bumping, has been developed at Motorola's Interconnect Systems Laboratory that uses baked photoresist as a mask for solder printing to deposit fine pitch solder bumps on wafers. This process provides much better alignment accuracy and is capable of bumping finer pitch devices than stencil printing technology. Solder paste printing uses a screen printer similar to that used for stencil printing. Greater versatility of solder materials can be obtained through solder paste than the electroplating. Cost modeling shows that the squeegee bump technology has a significant cost benefit over controlled collapse chip connection (C4) technology. This is because the C4 process has very low efficiency in labor and materials usage. Statistical process control data show an average bump height of 118 ± 3.5 μm, and a maximum-to-minimum bump height range of 17 μm over a 150 mm-diameter wafer and have been produced repeatedly on test wafers with 210 μm peripheral pitch. A 109.6 ± 1.3 μm bump height on orthogonal array with 250 μm pitch has been successfully demonstrated with greater than 90% die yield. Bump reliability has been studied using both multiple reflows and extended thermal/humidity storage procedures. No degradation of shear strength was observed after up to 10 × reflows and 1008 h of a thermal/humidity stress environment. Bump reliability was also evaluated by assembling squeegee bumped dice on a plastic chip scale package (CSP). Liquid-to-liquid thermal shock cycling at a temperature range of -55°C to +125°C had a characteristic life of 2764 cycles with a 1st failure at 1050 cycles. No failures were observed after 432 h of autoclave stress at 121°C, 100% RH, 15 psig test condition     

用面对面叠加法实现芯片的3D集成

面对面芯片叠加使一颗芯片置于另一颗芯片的倒装凸块阵列中,从而极大减小了封装厚度。POSSUMTM封装是指两颗或多颗芯片用面对面的方式叠加,其中较小的芯片置于较大芯片上没有互联倒装凸块的区域。较小的芯片在薄化后通过铜柱微块组装到较大的芯片上。因此,薄化了的较小芯片和它的铜柱微块的总体高度就比其附着的较大芯片的倒装凸块经回流后的高度要低很多。一旦组装完毕,较小芯片就被有效地夹在上面的较大芯片和下面的基板中,同时被一环或多环倒装锡凸块包围。底部填充剂的使用同时保证了铜柱和无铅锡凸块在测试和使用中的可靠性要求。因为信号在两颗芯片的表面运行,所以互连线极短,可以实现近距离信号匹配,和小电感的信号传输。这种面对面芯片叠加方式保证了很好的芯片间信号传输的完整性,是穿硅孔(TSV)封装技术的低成本的有效替代。     

Application assessment of high throughput flip chip assembly for ahigh lead-eutectic solder cap interconnect system using no-flowunderfill materials

Flip chip on board (FCOB) is one of the most quickly growing segments in advanced electronic packaging. In many cases, assembly processes are not capable of providing the high throughputs needed for integrated surface mount technology (SMT) processing (Tummala et al, 1997). A new high throughput process using no-flow underfill materials has been developed that has the potential to significantly increase flip chip assembly throughput. Previous research has demonstrated the feasibility and reliability of the high throughput process required for FCOB assemblies. The goal of this research was to integrate the high throughput flip chip process on commercial flip chip packages that consisted of high lead solder balls on a polyimide passivated silicon die bonded with eutectic solder bumped pads on the laminate substrate interface (Qi, 1999). This involved extensive parametric experimentation that focused on the following elements: no-flow process evaluation and implementation on the commercial packages, reflow profile parameter effects on eutectic solder wetting of high lead solder bumps, interactions between the no-flow underfill materials and the package solder interconnect and tented via features, void capture and void formation during processing, and material set compatibility and the effects on long term reliability performance     

Anisotropic conductive adhesives with enhanced thermal conductivity for flip chip applications

This paper presents the development of new anisotropic conductive adhesives (ACAs) with enhanced thermal conductivity for improved reliability of adhesive flip chip assembly under high current density condition. As the bump size in the flip chip assembly is reduced, the current density through the bump also increases. This increased current density causes new failure mechanisms, such as interface degradation due to intermetallic compound formation and adhesive swelling resulting from high current stressing. This process is found especially in high current density interconnection in which the high junction temperature enhances such failure mechanisms. Therefore, it is necessary for the ACA to become a thermal transfer medium that allows the board to act as a new heat sink for the flip chip package and improve the lifetime of the ACA flip chip joint. We developed the thermally conductive ACA of 0.63 W/m·K thermal conductivity by using a formulation incorporating the 5-μm Ni-filled and 0.2-μm SiC-filled epoxy-based binder system. The current carrying capability and the electrical reliability under the current stressing condition for the thermally conductive ACA flip chip joints were improved in comparison to conventional ACA. This improvement was attributed to the effective heat dissipation from Au stud bumps/ACA/PCB pad structure by the thermally conductive ACA.