原位复合制备纤维素基CdS纳米复合材料及其表征

以微晶纤维素(MCC)为模板,氯化镉、硫化钠等为原料,在水的悬浮液中,用原位复合法制备了MCC/CdS纳米复合材料。对复合反应条件进行了初步研究,探讨了Cd2+浓度、Cd2+吸附时间及超声功率对复合反应的影响。研究表明,适当提高Cd2+吸附时间及超声功率有利于提高复合材料中硫化镉颗粒的复合量,Cd2+浓度对复合量的影响是显著的。应用X射线衍射(XRD),扫描电镜(SEM),红外光谱(FT-IR),光致荧光光谱(PL)对MCC/CdS复合材料进行了表征。结果表明,复合在微晶纤维素上的CdS颗粒大小均一,且均匀分布在微晶纤维素模板表面;制备的复合材料具有一定的荧光特性。     

纤维素/CdS纳米复合材料的声化学制备及其光电性能

以无水氯化镉和硫化钠为原料,微晶纤维素MCC为模板,采用声化学法成功制备MCC/CdS纳米复合材料.用原子力显微镜(AFM),X射线衍射(XRD),荧光光谱(PL)以及光电化学实验对复合材料的结构及性能进行表征.研究表明,粒径为30-70nm的CdS粒子均匀分布于微晶纤维素表面,所得CdS粒子为立方型晶体.PL光谱分析...     

利用原子力显微镜研究预处理对木棉纤维/CdS纳米复合材料形貌结构的影响

对木棉纤维进行预处理,然后用预处理后木棉纤维与CdS进行原位复合制备木棉纤维/CdS纳米复合材料。利用扫描电镜(SEM)和原子力显微镜(AFM)对复合材料表面形貌结构进行了观察。用AFM定量地分析了预处理方法对木棉纤维/CdS纳米复合材料表面超微三维结构的影响。研究表明,相比未处理木棉纤维,预处理后木棉纤维/CdS纳米复合材料上CdS粒子的吸附量增大,且经过TEMPO氧化处理的木棉纤维所复合的CdS粒子的分布最均匀,粒径最均一。对于基于植物质纤维素资源为原料的纤维素/无机纳米复合材料的制备及其结构表征具有重要的参考价值。     

纳米纤维素/CdS纳米复合光电材料的制备和性能

以NaClO2为主要氧化剂,使用氧化漂白桉木浆制备C-6位羧基含量为0.8mmol/g的TEMPO氧化纤维素,然后将其剪切为纳米纤维素(NCC)。再以NCC为基材,以无水氯化镉及硫化钠为前驱体,用声化学法制备了NCC/CdS纳米复合光电材料。用X射线衍射(XRD)、场发射扫描电镜(SEM)、傅里叶红外光谱仪(FT-IR)以及光电化学实验对复合材料的结构及性能进行表征。结果表明,大量CdS纳米粒子复合在NCC基材上形成NCC/CdS纳米复合材料,CdS晶粒为立方型晶体,大小为7.3nm。用NCC/CdS纳米复合材料形成的薄膜器件在可见光区域的透光率高达60%。这种复合材料可产生1.35μA的光电流,其光电转换效率为微晶纤维素/CdS复合材料的6倍。     

复合结构纳米晶CdS∶Cu/CdS的制备及光学特性

在非配位溶剂中合成了高质量的CdS纳米晶核,并利用Cu²⁺离子对其进行掺杂,制备了CdS∶Cu纳米晶.通过进一步采用连续离子层吸附反应的方法对CdS∶Cu纳米晶进行表面修饰,得到CdS∶Cu/CdS复合结构纳米晶.利用X射线衍射(XRD),透射电镜(TEM),紫外可见吸收光谱(UV-Vis)和荧光光谱(PL)对其结构、形貌以及光学性质进行了表征和分析,结果表明:所制备的复合结构CdS∶Cu/CdS纳米晶为立方闪锌矿结构;与CdS纳米晶核相比,掺杂Cu²⁺可以使其表面态发光发生红移;在CdS∶Cu纳米晶中,通过改变掺杂Cu²⁺的浓度,可以实现表面态发光在570和620nm之间的连续调节.与未经包覆的CdS∶Cu纳米晶相比,包覆层CdS增强了纳米晶CdS∶Cu的稳定性.     

纤维素/聚乳酸复合材料的结构与性能

以机械球磨法预处理纸浆纤维素纤维,研究球磨对纤维素形貌和结构的影响;以纤维素颗粒为填料,通过熔融加工方法,制备出可完全再生且可完全降解的聚乳酸(PLA)复合材料,对复合材料的形貌、结构和性能进行了表征测试。结果表明,作为干法工艺,机械球磨可以简便地制备微晶纤维素(MCC)。加入纤维素颗粒以后,复合材料的冲击强度显著增加(最高达70.7%),断面出现韧性断裂特征;PLA的玻璃化转变温度和冷结晶温度升高,最大分解速率温度降低约15℃,热稳定性略有下降。     

废纸纤维/微晶纤维素增强PHBV复合材料性能研究

以聚羟基丁酸戊酸共聚酯(PHBV)作为基体,微晶纤维素(MCC)和废纸纤维作为增强体,采用注塑成型的方法制备可生物降解的复合材料。研究不同质量分数的MCC以及不同质量分数的废纸纤维作为共混填充材料对复合材料的力学、吸水及界面性能的影响。结果表明添加MCC后的复合材料力学性能整体都得到了提高,且在MCC质量分数为3%时复合材料的综合力学性能最好,共混填充后的复合材料则在废纸纤维的质量分数为10%时综合力学性能最好;复合材料的吸水性随着废纸纤维含量的增加而上升。扫描电镜分析发现,MCC与PHBV界面相容性较好,共混废纸纤维后界面性能下降。     

微晶纤维素表面接枝对苯二胺的制备及其荧光性能

以微晶纤维素(MCC)为原料,高碘酸钠(NaIO4)为氧化剂首先制备了双醛纤维素(DAC),进而与对苯二胺(PPDA)进行小分子接枝反应,得到对苯二胺改性的微晶纤维素。通过红外光谱、热重分析、示差扫描量热仪和荧光显微镜分别表征了MCC氧化和接枝前后样品的变化,以及产物的荧光性能。结果表明,MCC经高碘酸钠氧化,可选择性地将C2、C3键的羟基氧化成醛基;对苯二胺接枝于DAC后可形成碳氮双键,具有明显的荧光效应。     

原位法P3HT-COOH/CdS纳米复合材料的制备与表征

以二水乙酸镉(Cd(OOCCH3)2·2H2O)为镉源,硫粉(S)为硫源,二氯苯(DCB)和二甲基亚砜(DMSO)为混合溶剂,末端羧基化聚-3-己基噻吩(P3HT-COOH)为模板,原位法合成了P3HT-COOH/CdS纳米复合材料;并利用核磁共振氢谱、傅里叶变换红外光谱、X射线衍射、透射电子显微镜、紫外-可见光谱和荧光光谱等分析测试方法对其组成、形貌、光电性能等进行了表征。研究了不同反应温度及S/Cd摩尔比对复合材料形貌及光电性能的影响。实验结果表明,所合成的CdS纳米粒子均匀分布在P3HT-COOH/CdS复合材料中;CdS的尺寸和分布不仅受温度影响,还很大程度上受S/Cd摩尔比的影响;P3HT-COOH/CdS纳米复合材料有较强的荧光淬灭,表明CdS与P3HT-COOH之间有电荷转移。     

微晶纤维素的表面改性对己内酰胺聚合的复合材料性能的影响

利用2,4-甲苯异氰酸酯(TDI)对微晶纤维素(MCC)进行改性,将改性前后的纤维素(MCC和TMCC)分散到己内酰胺(CL)中并利用CL阴离子开环聚合制备得到MCC/PA6和TMCC/PA6复合材料,研究TDI对MCC表面改性对复合材料的影响。扫描电子显微镜和傅立叶红外光谱结果表明TDI和MCC表面发生了接枝反应。比较复合材料中CL的转化率,发现TMCC/PA6复合材料中CL的转化率比MCC/PA6复合材料中CL的转化率高;测试复合材料中PA6和纯PA6的分子量,结果表明TMCC/PA6复合材料中PA6的分子量明显高于MCC/PA6复合材料中PA6的分子量;测试MCC、TMCC含量为1%(质量分数)的复合材料与纯PA6在250℃的剪切粘度,发现复合材料在250℃下剪切粘度在低频下均比PA6高,且前者最高,高频时两者趋向一致。     

水热法制备纤维素基CdS纳米复合材料及其光催化性能研究

以棉花为纤维素基质,CdCl_2·21/2H_2O和L-半胱氨酸为原料,采用水热法制备了纤维素基CdS纳米复合材料。以亚甲基蓝(MB)为目标降解物,研究了反应时间和反应温度对该复合材料光催化性能的影响,通过XRD、SEM、FT-IR和UV-VisDRS对不同温度下制得的复合材料进行了结构表征。结果表明,反应温度为影响纤维素基CdS样品光催化活性的关键因素,且对样品中CdS的微观结构有显著影响。当反应温度为120℃时,样品的光催化活性最佳,反应50min对MB溶液的光降解率达到94.78%。经过3次循环其光降解率基本保持不变,表明纤维素基CdS是一种稳定有效的光催化剂。光催化增强机理分析表明,CdS光生电子迁移至纤维素表面,实现了与光生空穴的有效分离,从而增强了材料的光催化性能。     

Effect of Sulfur Precursor on Dimensions of One-dimensional CdS Nanocrystals

One-dimensional CdS nanocrystals have been prepared by solvothermal method using cadmium acetate as a cadmium precursor,elemental sulfur and Na2S,as a sulfur precursor,and ethylenediamine as a solvent at 150℃ for 5 h.The nanocrystals were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM) and UV-Vis absorption spectroscopy.XRD patterns indicate that both Na2S and elemental sulfur as the sulfur precursor result in CdS nanorods with wurtzite phase(h...     

Nanocomposites of cellulose/iron oxide: influence of synthesis conditions on their morphological behavior and thermal stability

Nanocomposites of cellulose/iron oxide have been successfully prepared by hydrothermal method using cellulose solution and Fe(NO₃)₃·9H₂O at 180 °C. The cellulose solution was obtained by the dissolution of microcrystalline cellulose in NaOH/urea aqueous solution, which is a good system to dissolve cellulose and favors the synthesis of iron oxide without needing any template or other reagents. The phases, microstructure, and morphologies of nanocomposites were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectra (EDS). The effects of the heating time, heating temperature, cellulose concentration, and ferric nitrate concentration on the morphological behavior of products were investigated. The experimental results indicated that the cellulose concentration played an important role in both the phase and shape of iron oxide in nanocomposites. Moreover, the nanocomposites synthesized by using different cellulose concentrations displayed different thermal stabilities.     

Preparation and characterization of Chitosan/Konjac glucomannan/CdS nanocomposite film with low infrared emissivity

Novel organic-inorganic nanocomposite films were prepared with Chitosan (CS), Konjac glucomannan (KGM) and CdS by one-step synthesis. As-prepared films were characterized by IR spectra, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and infrared emissometer (IR). The results indicated that grown CdS dendrites were formed with reaction time of 12 h for Cd²⁺ and CS/KGM, and were well dispersed in CS/KGM with an average diameter of 40 nm. The CS/KGM/CdS nanocomposite films had significantly low infrared emissivity. When the mole ratio of CdS to summation of CS&KGM construction units was 1.0 with CdS size of 10-20 nm, the film got the lowest infrared emissivity value of 0.011, which could be attributed to the strong synergism effect existing between CS/KGM and CdS dendrites.     

Biotemplated preparation of CdS nanoparticles/bacterial cellulose hybrid nanofibers for photocatalysis application

In this work, we describe a novel facile and effective strategy to prepare micrometer-long hybrid nanofibers by deposition of CdS nanoparticles onto the substrate of hydrated bacterial cellulose nanofibers (BCF). Hexagonal phase CdS nanocrystals were achieved via a simple hydrothermal reaction between CdCl(2) and thiourea at relatively low temperature. The prepared pristine BCF and the CdS/BCF hybrid nanofibers were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), UV-vis absorption spectroscopy (UV-vis), and X-ray photoelectron spectroscopy (XPS). The results reveal that the CdS nanoparticles were homogeneously deposited on the BCF surface and stabilized via coordination effect. The CdS/BCF hybrid nanofibers demonstrated high-efficiency photocatalysis with 82% methyl orange (MO) degradation after 90 min irradiation and good recyclability. The results indicate that the CdS/BCF hybrid nanofibers are promising candidate as robust visible light responsive photocatalysts.     

Facile microwave-combustion synthesis of wurtzite CdS nanoparticles

In this study we first report microwave-combustion synthesis of faceted CdS nanoparticles by using cadmium thiocyanate complex as a single source precursor. This is the first example of a metal-thiocyanate (M-SCN) complex being used as a source for metal sulfides (M-S) preparation in a microwave-combustion process. The synthesized CdS was characterized using X-ray diffraction (XRD), field mission scanning electron microscopy (FE-SEM), and high-resolution transmission electron microscopy (HR-TEM). The by-product assisted combustion synthesis yields CdS nanoparticles with the mixtures of octahedral geometries, hexagonal, and triangle plate morphologies and the sizes were found to be 100 nm to 5 microm. The XRD patterns imply the formation of well crystallized wurtzite CdS. The influence of cadmium and sulfur precursors and microwave irradiation time on the morphology of CdS nanoparticle was also investigated. The cadmium and sulfur precursors strongly influenced the CdS morphology and increasing the microwave irradiation time and intensity has no effect on the CdS morphology. In addition, a plausible mechanism of CdS nanoparticle formation has been proposed in this research.     

Preparation of CdS microtrumpets from a solvent extraction system by a two-phase approach

CdS microtrumpets with the length being of about 4 μm and the bell wall being of 100 nm have been prepared using a cadmium di-(2-ethylhexyl) phosphoric acid chelate as the precursor by a two-phase thermal approach. The products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV-vis spectroscopy. The effects of temperature, reaction time, and co-surfactant on the morphology were also examined. It was found that the co-surfactant triethanolamine plays a crucial role in the formation of the cubic phase trumpet-like CdS microstructures.     

Microwave-assisted synthesis and characterization of cellulose-carbonated hydroxyapatite nanocomposites in NaOH-urea aqueous solution

We report the microwave-assisted synthesis of the cellulose-carbonated hydroxyapatite (CHA) nanocomposites with CHA nanostructures dispersed in the cellulose matrix by using the cellulose solution, CaCl₂, and NaH₂PO₄. The cellulose solution was previously prepared by the dissolution of microcrystalline cellulose in NaOH-urea aqueous solution. The influences of the heating time and cellulose concentration on the products were also investigated. The X-ray powder diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR) results indicated that the obtained products were the cellulose-CHA nanocomposites. The scanning electron microscopy (SEM) micrographs showed the CHA nanostructures were dispersed in the cellulose matrix. The thermal stability of the cellulose-CHA nanocomposites in air was investigated using thermogravimetric analysis (TGA) and differential thermal analysis (DTA). This method is simple, fast, low-cost and suitable for large-scale production of cellulose-based nanocomposites.     

水热法合成一维GdV1-xPxO4∶Tm纳米材料及其发光性能

以乙二胺四乙酸(EDTA)为模板剂,采用水热法,成功地合成一系列具有较大长径比的一维GdV1-xPxO4∶Tm蓝色纳米荧光粉。利用X射线衍射仪、扫描电镜、荧光光谱仪对产物的相结构、形貌和发光性能进行了分析。结果表明所得产物均具有明显的一维特征,随P含量的增加,产物的长径比增加,纳米棒逐渐变细。产物在未经焙烧的条件下,在278nm波长紫外光激发下发出强度较高的波长为478nm的明亮蓝光,掺P摩尔比,即x=0.4时,所得产物的发光强度最好。