MODELLING OF EQUILIBRIUM SOLUBILITY OF CO2 AND H2S IN AQUEOUS AMINO METHYL PROPANOL (AMP) SOLUTIONS

Information on acid gas solubility in solvents utilized is needed for the design of gas plants. A mathematical model for the prediction of equilibrium solubility of CO₂ and H₂S in aqueous 2-amino-2-methyl-l-propanol (AMP) solutions is presented. The equilibrium constant, K₁ governing the main amine reaction is expressed as a function of not only temperature but also acid gas partial pressure and AMP concentration. Model predictions agree favourably with experimental data.     

Aspen Plus模拟高浓度H2S/CO2酸性气的选择性分离

以煤制氢尾气中的高浓度酸性气体H₂S和CO₂为对象,以聚乙二醇二甲醚（NHD）为吸收剂,使用PC-SAFT状态方程拟合了酸性气体CO₂和H₂S在聚乙二醇二甲醚（NHD）溶剂中溶解参数,运用Aspen Plus流程模拟软件,构建两级吸收分离工艺,实现H₂S和CO₂的高效分离,H₂S浓度由30%提升至98.7%,CO₂含量由55%提升至99.4%。由此,可以通过高效分离酸性气H₂S和CO₂,并以提浓后再资源化利用的方式实现酸性气的污染控制。     

硫化氢在 Primene JM-T 中溶解度的测定与模型建立简

The primary aliphatic amine Primene JM-T was investigated as a potential absorbent for H2S removal. The solubility of HzS in JM-T was measured at 298, 313,333,353, and 368 K with H2S partial pressures from 20 to 760 kPa and HzS loading from 0.02 to 0.8 mol H2S per mol JM-T. Relevant physical properties, such as density, viscoslty and dielectric constant, ot the matenal were measured. ＇The thermodynamlc model with two-suttlX Margules equation was used to correlate the experimental vapor-liquid equilibrium data. Furthermore, the absorption mechanism in non-aqueous system is suggested and the difference between non-aqueous and aqueous absorption system is pointed out.     

ABSORPTION OF SO2 AND H2S IN SMALL-SCALE VENTURI SCRUBBERS

Small-scale venturi scrubbers having geometries of typical large-scale units were constructed from glass and were operated in a laboratory system. Carrier gas streams consisting of air or nitrogen and up to 30% (by volume) CO₂ were mixed with SO₂ or H₂S to give SO₂ or H₂S concentrations in the range of 1890-4400 ppm. These gas mixtures were then scrubbed in the Venturis using various injected liquids (plain water, NaOH solutions, NH₄OH solutions, and NaOH/NaHCO₃ solutions) at L/G ratios of 0.0004-0.0040 m³ liquid per standard (1 atm, 60°F)m³ of gas (3-30 gallons liquid per 1000 standard ft³ of gas). Absorption percentages for SO₂ and H₂S were determined as functions of the L/G ratio, initial liquid pH, and liquid composition. The effects of venturi throat length, gas velocity, and the presence of CO₂ in the gas stream were also determined.     

SOLUBILITY OF CO2AND H2S IN A MIXED SOLVENT

Mixed solvents are a combination of chemical and physical solvents and have some advantages over traditional treating solvents for the removal of acid gases from gas streams. The solubility of H₂S and CO₂in a mixed solvent consisting of AMP (2-amino-2-methyl-l-propanol), sulfolane, and water has been measured at 40 and 100°C at partial pressures of the acid gas to 6000 kPa. The solubility in the mixed solvent was compared with the solubility in an aqueous solution of equivalent amine concentration. At solution loadings less than 1 mol acid gas/mol amine, the solubility of the acid gas is lower in the mixed solvent than in the corresponding amine solvent. At higher loadings, the trend is reversed and the solubility is greater in the mixed solvent. The results are rationalized in terms of the effect of the physical solvent component on the chemical reaction and physical vapor-liquid equilibria. The solubility model of Deshmukh and Mather was used to correlate the data.     

SIMULTANEOUS ABSORPTION OF H2S AND CO2 INTO A SOLUTION OF SODIUM CARBONATE

The simultaneous absorption of H₂S and CO₂ has been studied both experimentally and theoretically. A model has been developed which predicts the absorption rates of H₂S and CO₂ into a sodium carbonate solution. The absorption rates are calculated according to the two-film theory. In the liquid film, the finite rate of the CO₂ reaction was considered. Otherwise, in the liquid film as well as in the liquid bulk, equilibrium conditions for all reactions were assumed. Absorption experiments were performed on a packed column using a counter-flow strategy. In the experiments the influence of the initial carbonate concentration, the gas flow rate and the temperature on the removal efficiencies of H₂S and CO₂ and the selectivity of H₂S were investigated. It is desirable to absorb the H₂S but not the CO₂. The agreement between the absorption model and the experimental results from the absorber tower was satisfactory. The mass transfer coefficients were determined by fitting the experimental data to the model with respect to the H₂S and CO₂ content in the outgoing gas. The H₂S content was used to determine the gas side mass transfer coefficient and the CO₂ content was used to determine the liquid side mass transfer coefficient, The effective contact area of mass transfer was taken from published data. With a constant packing height, both the experiments and the model indicated that high carbonate concentration benefits the removal efficiency of H₂S. Higher gas flow rate also benefits the selectivity for H₂S. However, the removal efficiency will decrease. At higher temperatures the selectivity and the removal efficiency of H₂S decreased. Under the conditions investigated, the absorption of H₂S was essentially controlled by gas-side mass transfer and the absorption of CO₂ was controlled by liquid-side mass transfer     

Primary nucleation of citric acid monohydrate: influence of selected impurities

An experimental study is presented concerning solubility and primary nucleation kinetics of monohydrate citric acid from pure and selectively impure (KH₂PO₄, MgSO₄ · 7H₂O and FeSO₄ · 7H₂O) aqueous solutions. The metastable range of pure solutions is wide, ranging from 6 to 14°C, and the order of primary nucleation, equal to 2.51, is quite low. The addition of the tested impurities, which are usual fermentation aids, at concentrations lower than wt. 1%, produces negligible effects on the solubility and slightly enhances the primary nucleation rate. However, the presence of these compounds modifies the crystal habit at birth: in particular, the addition of MgSO₄ · 7H₂O and FeSO₄ · 7H₂O makes these crystals more elongated, but this effect diminishes as the crystals grow.     

Investigation of CoNiMo/Al2O3 catalysts: Relationship between H2S adsorption and HDS activity

Sulfidation of trimetallic CoNiMo/Al₂O₃ catalysts was studied by thermogravimetry at 400 °C under flow and pressure conditions. Results were compared with those obtained on prepared and industrial CoMo/Al₂O₃ and NiMo/Al₂O₃ catalysts. The amount of sorbed H₂S on the sulfided solids was measured at 300 °C in the H₂S pressure range 0–3.5 MPa at constant H₂ pressure (3.8 MPa). The adsorption isotherms were simulated using a model featuring dissociated adsorption of H₂S on supported metal sulfides and bare alumina. The amount of sulfur-vacancy sites could thus be determined under conditions close to industrial practice. A relationship with activity results for thiophene HDS and benzene hydrogenation was sought for.     

CATALYTIC PRODUCTION OF ELEMENTAL SULFUR FROM THE THERMAL DECOMPOSITION OF H2S IN THE PRESENCE OF CO2

The feasibility of using a cobalt-molybdenum (Co-Mo) sulfide catalyst that was prepared from a commercial Co-Mo oxide catalyst for the production of elemental sulfur from hydrogen sulfide (H₂S) and carbon dioxide (CO₂) in a packed bed catalytic reactor was studied. It was demonstrated that the desired sulfide catalyst could be prepared by first reducing, then sulphiding the corresponding oxide. The results showed that the prepared catalyst was capable of producing elemental sulfur from the thermal decomposition of H₂S in the presence of CO₂ over a temperature range of 465-700°C and at atmospheric pressure. A specific rate coefficient was calculated as well as the Arrhenius parameters for the non-equilibrated reaction. The H₂S decomposition reaction was found to be a second order reaction and have an activation energy of 114.4kJ/mol(27.3kcal/mol).     

Kinetics of dibenzothiophene hydrodesulfurization over MoS2 supported catalysts: modelization of the H2S partial pressure effect

The influence of H₂S partial pressure over the catalytic activity of MoS₂, supported on three different oxides: Al₂O₃, TiO₂ and ZrO₂, was studied in the hydrodesulfurization of dibenzothiophene (DBT). A complex inhibiting effect is observed and two orders of reaction relative to H₂S were determined: −1/2 and 0, as a function of H₂S partial pressure. The experimental results are in good agreement with the kinetic models whereby the DBT transformation takes place through a dihydrogenated intermediate (DH-DBT). The associated mechanism considers that the heterolytic dissociative adsorption of H₂ and H₂S occurs over an unsaturated Mo ion and over a stable sulfur ion.     

Hydrocracking of diphenylmethane: Roles of H2S and pyrrhotite

To define the roles of H₂S and pyrrhotite in high temperatures employed for normal coal liquefaction, diphenylmethane hydrocracking with H₂ and H₂-H₂S was carried out with and without pyrrhotite. H₂S promotes diphenylmethane hydrocracking with H₂ both in the presence and absence of pyrrhotite, and the reaction is dependent upon the H₂S pressure in both instances. It is also dependent on the H₂ pressure when pyrrhotite is present. The results are interpreted in terms of H₂S acting as a hydrogen transfer catalyst.     

化学链燃烧中H2S对NiFe2O4氧载体活性的影响机理

采用密度泛函理论方法研究H₂S与NiFe₂O₄（001）完整表面和氧缺陷表面的相互作用机理。结果表明,H₂S在NiFe₂O₄氧载体表面Ni原子位的吸附能比其在Fe原子位的吸附能大。氧缺陷的形成会使H₂S在氧载体表面金属原子位的吸附能增大,并且Ni原子位吸附H₂S的吸附能增加更为明显。因而,NiFe₂O₄氧载体表面的Ni原子位是H₂S的主要吸附位。同时采用热力学方法进一步研究含H₂S的合成气与NiFe₂O₄氧载体之间的反应,发现H₂S与氧载体的反应产物与氧载体的还原程度密切相关。由于铁氧化物的深度还原过程受到热力学限制,H₂S与NiFe₂O₄氧载体反应的主要产物为Ni₃S₂。密度泛函理论方法与热力学方法研究结果均表明H₂S倾向于与NiFe₂O₄氧载体中Ni发生相互作用,这将对NiFe₂O₄氧载体的反应性能产生不利影响。     

ZSM-5催化剂与低温等离子体协同转化H2S-CO2制合成气

将H₂S和CO₂混合酸气一步转化制合成气,既实现了二者无害化处理,又生产出合成气,是一条理想的废气资源化利用新路线。由于分子结构稳定,在常规条件下因受热力学平衡限制,二者转化率极低。而在低温等离子体中,H₂S和CO₂可被激发为高活性物种来参与反应。研究了具有不同Si/Al摩尔比的ZSM-5催化剂与低温等离子体结合实现H₂S-CO₂一步高选择性制合成气,显著提高了H₂S-CO₂转化性能。考察了ZSM-5催化剂中Si/Al比和低温等离子体放电条件等对反应的影响。其中,当Si/Al比为80时表现出最优催化性能,最高H₂和CO产率分别达到56.1%和10.0%。对常规条件和低温等离子体氛围下的不同ZSM-5催化剂上CO₂、H₂S、CO、H₂等化学吸脱附行为进行了对比研究,发现低温等离子体促进了催化剂对CO₂、H₂及CO分子的吸附活化,进而明显提升了H₂S和CO₂转化。     

Sulfur exchange on Co---Mo/Al2O3 hydrodesulfurization catalyst using S radioisotope tracer

A commercial Co---Mo/Al₂O₃ catalyst was labeled with the radioisotope ³⁵S in hydrodesulfurization (HDS) of ³⁵S-labeled dibenzothiophene (³⁵S-DBT) in a high-pressure flow reactor at 50 kg/cm². Then, HDS of 4-methyldibenzothiophene (4-MDBT) and 4,6-dimethyldibenzothiophene (4,6-DMDBT) or sulfur exchange of H₂S were carried out on the labeled catalyst at 50 kg/cm² and 260–360°C. The amounts of labile sulfur participating in the reaction were determined from the radioactivity of ³⁵S---H₂S released from the ³⁵S-labeled catalyst. In the HDS reactions, the amount of labile sulfur participating in the reaction decreased in the order: DBT> 4-MDBT> 4,6-DMDBT. In the sulfur exchange reaction with H₂S, the adsorption of H₂S on the catalyst reached saturation above a H₂S partial pressure of 0.36 kg/cm². It was suggested that the release of H₂S from the labile sulfur may be the rate determining step of the HDS reaction.     

Catalytic wet oxidation of H2S to sulfur on Fe/MgO catalyst

The room temperature wet catalytic oxidation was conducted in a batch reactor with Fe/MgO catalyst. Fe/MgO catalyst was prepared by the dissolution–precipitation method. XRD and temperature-programmed reductions (TPR) indicate that Fe oxide in the Fe/MgO is finely dispersed in the MgO support. The high H₂S removal capacities of Fe/MgO can be explained by the finely dispersed iron oxide MgO. The H₂S removal capacities of Fe/MgO are dependent on oxygen partial pressure (1.0 g H₂S/g_cat in air and 2.6 g H₂S/g_cat in oxygen). The valence state analysis of Fe/MgO catalyst suggests that the H₂S oxidation on Fe/MgO can occur by a redox couple reaction, reducing Fe³⁺ into Fe²⁺ by H₂S and oxidizing Fe²⁺ to Fe³⁺ by O₂.     

循环捕集CO2后煅烧石灰石的硫化特性

ZEC(zero emission coal)系统中,粗煤气进入碳酸化/重整炉前需先脱除H₂S,提出利用经过多次碳酸化/煅烧捕集CO₂循环的煅烧石灰石(CaO)脱除H₂S,并研究循环碳酸化/煅烧次数、硫化温度、H₂S浓度和微观结构对循环CaO硫化特性的影响。结果表明,多次循环碳酸化/煅烧捕集CO₂后CaO仍具有较高H₂S吸收性能。前20次循环,CaO硫化转化率随循环次数增加迅速降低;20次循环后,CaO硫化转化率缓慢下降。硫化120 min后,未循环CaO的硫化转化率接近100%,而经历1、20和100次循环后CaO的硫化转化率分别为94%、81%和74%。H₂S浓度对循环CaO硫化性能影响较大。硫化温度(800～1000℃)对循环CaO的硫化性能影响较小,最佳硫化温度为900℃。随循环次数增加,CaO颗粒发生高温烧结,导致比表面积降低和20～150 nm内孔隙减少,而这是与H₂S吸收密切相关的孔隙,导致CaO硫化转化率降低。     

HCN、COS和CS2催化水解及其水解产物协同净化的研究进展

氰化氢（HCN）、羰基硫（COS）、二硫化碳（CS₂）广泛共存于黄磷尾气、焦炉煤气、碳一化工等化工行业废气中,目前大多数研究局限于3种气体的单独脱除,3种气体同时脱除的研究鲜有报道,而3种气体的协同脱除势在必行。催化水解法能够将HCN转化成NH₃,COS和CS₂水解成H₂S。NH₃和H₂S可以分别被催化氧化为N₂及S,S可以回收利用。一步法实现HCN、COS和CS₂的水解及水解产物NH₃和H₂S的催化氧化的催化剂开发是该技术的核心问题,本文针对近几年3种气体水解催化剂的相关研究成果进行了综述,包括负载型催化剂和非负载型催化剂,与此同时,针对水解产物NH₃和H₂S的催化氧化的协同净化技术进行了分析,旨在为后续3种气体同时催化水解及协同净化其水解产物催化剂的开发提供理论指导,为低温环境下协同催化水解HCN、COS和CS₂,并利用原料气中的氧一步法净化水解产物技术的未来发展及应用提供参考。     

Synthesis of mixed alcohols from CO2 contained syngas on supported molybdenum sulfide catalysts

The performances of active carbon supported molybdenum sulfide catalysts prepared by different procedures or promoted by different elements in the synthesis of mixed alcohols from CO₂ containing syngas were examined. The results showed that high alcohol activity and selectivity could be obtained by employing a rapid drying procedure and employing a H₂S---H₂ stream for (NH₄)₂MoS₄ decomposition. Addition of Co, Cr and Cl to K---Mo/C catalyst led to an increase in the alcohol activity or selectivity. The presence of CO₂ in the feed caused a greater amount of water to be produced but reduced the formation of CO₂. The product distribution was also strongly influenced by the presence of either CO₂ or H₂S in the feed. Addition of CO₂ reduces the formation of higher alcohols while H₂S increases higher alcohol formation.     

Influence of water and ammonia on hydrotreating catalysts and activity for tetralin hydrogenation

The effects of H₂O and NH₃ on the kinetics of the liquid phase hydrogenation of tetralin to decalin at 6.9 MPa and 330°C over commercial P---Ni---Mo/alumina catalysts in the presence of H₂S have been investigated. H₂O functioned as a mild kinetic inhibitor to an extent sensitive to the H₂S level. Quasi in situ XPS was used to investigate the catalyst structure after exposure to H₂0/H₂S.     

H2S为毒物对乙炔氢氯化反应中AuCl3/AC催化剂催化活性的影响

采用等体积浸渍法制备了1% AuCl₃/AC催化剂,探究了硫化氢(H₂S)为毒物对乙炔氢氯化反应中催化剂催化活性的影响及失活机理。催化活性测试结果表明,以H₂S为毒物可导致乙炔氢氯化反应中的AuCl₃/AC催化剂的失活,且是一个不可逆过程;程序升温还原(TPR)和X射线光电子能谱(XPS)分析结果表明,H₂S的加入可有效地加快Au³⁺还原为Au⁰;透射电镜能谱(TEM-EDX)观测分析形成的Au-S化合物也可导致催化剂失活,即随着H₂S量的增大,更多的Au³⁺被还原为Au⁰,且形成的Au-S化合物覆盖在活性位点,使有效的活性组分降低进而导致AuCl₃/AC催化剂失活。