Effect of operating conditions and gas flow patterns on the system performances of IIR-SOFC fueled by methanol

Mathematical models of an indirect internal reforming solid oxide fuel cells (IIR-SOFC) fueled by methanol were developed to analyze the thermal coupling of the internal endothermic steam reforming with exothermic electrochemical reactions and predict the system performance. The simulations indicated that IIR-SOFC fueled by methanol can be well performed as autothermal operation, although slight temperature gradient occurred at the entrance of the reformer chamber. Sensitivity analysis of five important parameters (i.e. operating voltage, reforming catalyst reactivity, inlet steam to carbon ratio, operating pressure and flow direction) was then performed. The increase of operating voltage lowered the average temperature along the reformer chamber and improved the electrical efficiency, but it oppositely reduced the average current density. Greater temperature profile along the system can be obtained by applying the catalyst with lower reforming reactivity; nevertheless, the current density and electrical efficiency slightly decreased. By using high inlet steam to carbon ratio, the cooling spot at the entrance of the reformer can be reduced but both current density and electrical efficiency were decreased. Lastly, with increasing operating pressure, the system efficiency increased and the temperature dropping at the reformer chamber was minimized.     

Modeling of IT-SOFC with indirect internal reforming operation fueled by methane: Effect of oxygen adding as autothermal reforming

Mathematical models of an Intermediate Temperature Solid Oxide Fuel Cell (IT-SOFC) with indirect internal reforming operation (IIR-SOFC) fueled by methane were developed. The models were based on a steady-state heterogeneous two-dimensional tubular-design SOFC. The benefit in adding oxygen to methane and steam as the feed for autothermal reforming reaction on the thermal behavior and SOFC performance was simulated. The results indicated that smoother temperature gradient with lower local cooling at the entrance of the reformer channel can be achieved by adding a small amount of oxygen. However, the electrical efficiency noticeably decreased when too high oxygen content was added due to the loss of hydrogen generation from the oxidation reaction; hence, the inlet oxygen to carbon (O/C) molar ratio must be carefully controlled. Another benefit of adding oxygen is the reduction of excess steam requirement, which could reduce the quantity of heat required to generate the steam and eventually increases the overall system performance. It was also found that the operating temperature strongly affects the electrical efficiency achievement and temperature distribution along the SOFC system. By increasing the operating temperature, the system efficiency increases but a significant temperature gradient is also detected. The system with a counter-flow pattern was compared to that with a co-flow pattern. The co-flow pattern provided smoother temperature gradient along the system due to better matching between the heat supplied from the electrochemical reaction and the heat required for the steam reforming reaction. However, the electrical efficiency of the co-flow pattern is lower due to the higher cell polarization at a lower system temperature.     

Hydrogen-rich syngas production and carbon dioxide formation using aqueous urea solution in biogas steam reforming by thermodynamic analysis

Biogas is a renewable biofuel that contains a lot of CH₄ and CO₂. Biogas can be used to produce heat and electric power while reducing CH₄, one of greenhouse gas emissions. As a result, it has been getting increasing academic attention. There are some application ways of biogas; biogas can produce hydrogen to feed a fuel cell by reforming process. Urea is also a hydrogen carrier and could produce hydrogen by steam reforming. This study then employes steam reforming of biogas and compares hydrogen-rich syngas production and carbon dioxide with various methane concentrations using steam and aqueous urea solution (AUS) by Thermodynamic analysis. The results show that the utilization of AUS as a replacement for steam enriches the production of H₂ and CO and has a slight CO₂ rise compared with pure biogas steam reforming at a temperature higher than 800 °C. However, CO₂ formation is less than the initial CO₂ in biogas. At the reaction temperature of 700 °C, carbon formation does not occur in the reforming process for steam/biogas ratios higher than 2. These conditions led to the highest H₂, CO production, and reforming efficiency (about 125%). The results can be used as operation data for systems that combine biogas reforming and applied to solid oxide fuel cell (SOFC), which usually operates between 700 °C to 900 °C to generate electric power in the future.     

A review of biomass-derived fuel processors for fuel cell systems

Fuel cell coupled with biomass-derived fuel processor can convert renewable energy into a useful form in an environmental-friendly and CO₂-neutral manner. It is considered as one of the most promising energy supply systems in the future. Biomass-derived fuels, such as ethanol, methanol, biodiesel, glycerol, and biogas, can be fed to a fuel processor as a raw fuel for reforming by autothermal reforming, steam reforming, partial oxidation, or other reforming methods. Catalysts play an important role in the fuel processor to convert biomass fuels with high hydrogen selectivity. The processor configuration is another crucial factor determining the application and the performance of a biomass fuel processing system. The newly developed monolithic reactor, micro-reactor, and internal reforming technologies have demonstrated that they are robust in converting a wide range of biomass fuels with high efficiency. This paper provides a review of the biomass-derived fuel processing technologies from various perspectives including the feedstock, reforming mechanisms, catalysts, and processor configurations. The research challenges and future development of biomass fuel processor are also discussed.     

Experimental evaluation of methanol steam reforming reactor heated by catalyst combustion for kW-class SOFC

The distributed power generation of methanol steam reforming reactor combined with solid oxide fuel cell (SOFC) has the characteristics of outstanding economic advantages. In this paper, a methanol steam reforming reactor was designed which integrates catalyst combustion, vaporization and reforming. By catalyst combustion, it can achieve stable operation to supply fuel for kW-class SOFC in real time without additional heating equipment. The optimal operating condition of the reforming reactor is 523–553 K, and the steam to carbon ratio (S/C) is 1.2. To study the reforming performance, methanol steam reforming (MSR), methanol decomposition (MD), water-gas shift (WGS) were considered. Operating temperature is the greatest factor affecting reforming performance. The higher the reaction temperature, the lower the H₂ and CO₂, the higher the CO and the methanol conversion rate. The methanol conversion rate is up to 95.03%. The higher the liquid space velocity (LHSV), the lower the methanol conversion rate, the lowest is 90.7%. The temperature changes of the reforming reactor caused by the load change of stack takes about 30 min to reach new balance. Local hotspots within the reforming reactor lead to an excessive local temperature to test a small amount of CH₄ in the reforming gas. The methanation reaction cannot be ignored at the operating temperature. The reforming gas contains 70–75% H₂, 3–8% CO, 18–22% CO₂ and 0.0004–0.3% CH₄. Trace amounts of C₂H₆ and C₂H₄ are also found in some experiments. The reforming reactor can stably supply the fuel for up to 1125 W SOFC.     

Performance of a PEMFC system integrated with a biogas chemical looping reforming processor: A theoretical analysis and comparison with other fuel processors (steam reforming,partial oxidation and auto-thermal reforming)

In this work, the performance of a PEMFC (proton exchange membrane fuel cell) system integrated with a biogas chemical looping reforming processor is analyzed. The global efficiency is investigated by means of a thermodynamic study and the application of a generalized steady-state electrochemical model. The theoretical analysis is carried out for the commercial fuel cell BCS 500W stack. From literature, chemical looping reforming (CLR) is described as an attractive process only if the system operates at high pressure. However, the present research shows that advantages of the CLR process can be obtained at atmospheric pressure if this technology is integrated with a PEMFC system. The performance of a complete fuel cell system employing a fuel processor based on CLR technology is compared with those achieved when conventional fuel processors (steam reforming (SR), partial oxidation (PO) and auto-thermal reforming (ATR)) are used. In the first part of this paper, the Gibbs energy minimization method is applied to the unit comprising the fuel- and air-reactors in CLR or to the reformer (SR, PO, ATR). The goal is to investigate the characteristics of these different types of reforming process to generate hydrogen from clean model biogas and identify the optimized operating conditions for each process. Then, in the second part of this research, material and energy balances are solved for the complete fuel cell system processing biogas, taking into account the optimized conditions found in the first part. The overall efficiency of the PEMFC stack integrated with the fuel processor is found to be dependent on the required power demand. At low loads, efficiency is around 45%, whereas, at higher power demands, efficiencies around 25% are calculated for all the fuel processors. Simulation results show that, to generate the same molar flow-rate of H₂ to operate the PEMFC stack at a given current, the global process involving SR reactor is by far much more energy demanding than the other technologies. In this case, biogas is burnt in a catalytic combustor to supply the energy required, and there is a concern with respect to CO₂ emissions. The use of fuel processors based on CLR, PO or ATR results in an auto-thermal global process. If CLR based fuel processor is employed, CO₂ can be easily recovered, since air is not mixed with the reformate. In addition, the highest values of voltage and power are achieved when the PEMFC stack is fed on the stream coming from SR and CLR fuel processors. When a H₂ mixture is produced by reforming biogas through PO and ATR technologies, the relative anode overpotential of a single cell is about 55 mV, whereas, with the use of CLR and SR processes, this value is reduced to ∼37 and 24 mV, respectively. In this way, CLR can be seen as an advantageous reforming technology, since it allows that the global process can be operated under auto-thermal conditions and, at the same time, it allows the PEMFC stack to achieve values of voltage and power closer to those obtained when SR fuel processors are used. Thus, efforts on the development of fuel processors based on CLR technology operating at atmospheric pressure can be considered by future researchers. In the case of biogas, the CO₂ captured can produce additional economical benefits in a ‘carbon market’.     

Effects of operations and structural parameters on the one-cell stack performance of planar solid oxide fuel cell

A three-dimensional mathematical model coupling the electrochemical kinetics with fluid dynamics is developed to simulate the heat and mass transfer in the one-cell stack of planar solid oxide fuel cells (SOFCs). Based on flow uniformity analysis, the distributions of temperature, current density, overpotential loss and other performance parameters in various operating parameters are obtained using a commercial CFD code (Fluent) coupled with the external subroutines programmed by VC++. Numerical flow data are observed in good agreement with experimental results reported in the literature. Results show that the one-cell stack in counter flow case has the advantages in better uniform current density and temperature distributions of PEN (Positive/Electrolyte/Negative) structure in the width direction, higher power output, fuel utilization factor and fuel efficiency than that in co-flow case. For counter flow case, better thermoelectric characteristics are observed in the temperature gradient, power output, fuel utilization factor and fuel efficiency with the decrease in the fuel inlet flow rate or the anode porosity. Increasing the air inlet flow rate and decreasing the fuel inlet temperature will reduce the temperature gradient; power output, fuel utilization factor and fuel efficiency are enhanced with the increase of the air inlet temperature and the decrease of the anode pore size and thickness.     

Autothermal sorption-enhanced steam reforming of bio-oil/biogas mixture and energy generation by fuel cells: Concept analysis and process simulation

A concept of sorption-enhanced steam reforming of bio-oil/biogas for electricity and heat generation by phosphoric acid fuel cells is investigated. The process is modeled using SIMSCI Pro II process simulator. Sorptive removal of the carbon dioxide from the reaction site results in low CO and _CO2${\mathrm{CO}}_2$ concentrations (<1%$<1\%$) in the reformate, as a result it can be used in the phosphoric acid fuel cell without any further fuel cleanup. High hydrogen concentration and calorific value of the reformate enable the operation of the fuel cell at a high-efficiency mode despite of the high carbon/hydrogen ratio of the bio-fuel. Addition of biogas to the reformer enables autothermal operation of the reformer, as well as significantly improves the efficiency of the process. The simulation shows that the overall efficiency of the proposed system is compatible with the efficiency of the system using “classical” steam reforming of the fuel. The process exhibits 6% lower electrical efficiency compared to the system utilizing natural gas, and 4.6% higher efficiency compared to a system using bio-oil as a fuel.     

Analysis of phase change heat transfer with annulus 1 kW class methanol steam reforming reaction under high-pressure operation

A fuel cell air independent propulsion (AIP) system of underwater vehicle requires a hydrogen storage system. The methanol steam reforming system is a candidate of hydrogen storage which can produce hydrogen from chemical reaction. Different from reforming system for station fuel cell system, the methanol steam reformer (MSR) for underwater vehicle requires high-pressure operation.Since the longitudinal temperature uniformity is a core parameter of conversion efficiency of steam reforming system, this study is focused on computational analysis of phase change heat transfer through the annulus for methanol steam reforming reaction. The annulus MSR using phase change material was developed to improve the temperature uniformity. The simulation model is verified with safety and performance analysis code (SPACE). The performance parameters of MSR were flow arrangement, steam to carbon ratio (SCR), and gas hourly space velocity (GHSV). The results were analyzed in terms of the hydrogen yield, heat flux, liquid mass flow rate, and methanol conversion rate. The flow arrangement varied the methanol conversion rate to a minor extent of approximately 0.1% because wall temperature was maintained uniformly. In the case of SCR, the hydrogen yield at SCR 2.5 was 0.637 (dry basis), which was the highest yield rate. Also, if GHSV was increased, hydrogen yield decreased from 0.690 (dry basis) to 0.527 (dry basis). The heat transfer pattern was also analyzed and it was found that steam is interactively condensed along with the progress of the reforming reaction.     

Biogas as hydrogen source for fuel cell applications

In the last decade, production of biogas from biomass degradation has attracted the attention of several research groups. The interest on this hydrogen source is focused on the potential use of this gas as raw material to supply high temperature fuel cells (HTFC). This paper reports a wide research investigation carried out at CNR-ITAE on biogas reforming processes (steam reforming, autothermal reforming and partial oxidation). A mathematical model was developed, in Aspen Plus, and an experimental validation was made in order to confirm model results. Simulations were performed to determine the reformed gas composition and the system energy balance as a function of process temperature and pressure. The value of Gas Hour Space Velocity (GHSV) was selected for calculating compositions at full equilibrium, as it is expected in operative large scale plant. To obtain a realistic evaluation of the reforming processes efficiency, the energy balance for each examined process was developed as available energy of outlet syngas on inlet required energy ratio. The comparison between values of efficiency process gives useful indication about their reliability to be integrate with fuel cell systems.     

A thermodynamic analysis of biogas partial oxidation to synthesis gas with emphasis on soot formation

A thermodynamic analysis of synthesis gas production via partial oxidation (POX) of biogas is performed in the present article. Chemical equilibrium calculations are conducted for partial oxidation of (CH₄+CO₂) mixtures based on Gibbs free energy minimization method emphasizing soot formation. Regarding precise evaluation of carbon dioxide effects on the reforming characteristics, the obtained results are compared with the experimental data. Furthermore, the effects of steam injection at the inlet of the reformer on the coking behavior and syngas production yield are studied. To investigate the effects of the equivalence ratio (?), temperature and pressure, a broad parametric study is performed. The results reveal that the process temperature plays a pivotal role in enhancing the syngas production and soot abatement. It is also found that the pressure has an impractical effect on the syngas production yield, leading to the soot formation and decrease in both hydrogen and carbon monoxide yields. Furthermore, increasing the inlet CO₂/CH₄ makes the thermal reforming efficiency to rise at an equivalence ratio lower than 3. Meanwhile, increasing the steam to methane (S/C) ratio reduces carbon formation and enhances hydrogen production. Nonetheless, when the S/C ratio is larger than 2 at ? = 2.5 and 1 at ? = 3, the enhancement of hydrogen generation is minimized and even tends to become impractical. Therefore, near adiabatic and atmospheric condition at ? = 2.5–3 with S/C < 1 are recommended as the optimum operating routes for partial oxidation of biogas.     

Two novel oxy-fuel power cycles integrated with natural gas reforming and CO2 capture

Two novel system configurations were proposed for oxy-fuel natural gas turbine systems with integrated steam reforming and CO₂ capture and separation. The steam reforming heat is obtained from the available turbine exhaust heat, and the produced syngas is used as fuel with oxygen as the oxidizer. Internal combustion is used, which allows a very high heat input temperature. Moreover, the turbine working fluid can expand down to a vacuum, producing an overall high-pressure ratio. Particular attention was focused on the integration of the turbine exhaust heat recovery with both reforming and steam generation processes, in ways that reduce the heat transfer-related exergy destruction. The systems were thermodynamically simulated, predicting a net energy efficiency of 50–52% (with consideration of the energy needed for oxygen separation), which is higher than the Graz cycle energy efficiency by more than 2 percentage points. The improvement is attributed primarily to a decrease of the exergy change in the combustion and steam generation processes that these novel systems offer. The systems can attain a nearly 100% CO₂ capture.     

Study on a novel solid oxide fuel cell/gas turbine hybrid cycle system with CO2 capture

A novel solid oxide fuel cell (SOFC)/gas turbine (GT) hybrid cycle system with CO₂ capture is proposed based on a typical topping cycle SOFC/GT hybrid system. The H₂ gas is separated from the outlet mixture gas of SOFC1 anode by employing the advanced ceramic proton membrane technology, and then, it is injected into SOFC2 to continue a new electrochemical reaction. The outlet gas of SOFC1 cathode and the exhaust gas from SOFC2 burn in the afterburner 1. The combustion gas production of the afterburner1 expands in the turbine 1. The outlet gas of SOFC1 anode employs the oxy‐fuel combustion mode in the afterburner 2 after H₂ gas is separated. Then, the combustion gas production expands in the turbine 2. To ensure that the flue gas temperature does not exceed the maximum allowed turbine inlet temperature, steam is injected into the afterburner 2. The outlet gas of the afterburner 2 contains all the CO₂ gas of the system. When the steam is removed by condensation, the CO₂ gas can be captured. The steam generated by the waste heat boiler is used to drive a refrigerator and make CO₂ gas liquefied at a lower temperature. The performance of the novel quasi‐zero CO₂ emission SOFC/GT hybrid cycle system is analyzed with a case study. The effects of key parameters, such as CO₂ liquefaction temperature, hydrogen separation rate, and the unit oxygen production energy consumption on the new system performance, are investigated. Compared with the other quasi‐zero CO₂ emission power systems, the new system has the highest efficiency of around 64.13%. The research achievements will provide the valuable reference for further study of quasi‐zero CO₂ emission power system with high efficiency. Copyright © 2011 John Wiley & Sons, Ltd.     

Numerical studies of sorption-enhanced glycerol steam reforming in a fluidized bed membrane reactor at low temperature

In order to improve the hydrogen production efficiency by glycerol steam reforming, a membrane-assisted fluidized bed reactor with carbon dioxide sorption is developed to enhance the reforming process. Low-temperature operation in a membrane reactor is necessary considering the thermal stability of membrane. In this work, the sorption-enhanced glycerol steam reforming process in a fluidized bed membrane reactor under the condition of low temperature is numerically investigated, where the hydrotalcite is employed as CO₂ sorbents. The impact of operating pressure on the reforming performance is further evaluated. The results demonstrate that the integration of membrane hydrogen separation and CO₂ sorption can effectively enhance the low-temperature glycerol reforming performance. The fuel conversion above 95% can be achieved under an elevated pressure.     

An integrated power generation system combining solid oxide fuel cell and oxy-fuel combustion for high performance and CO2 capture

An integrated power generation system combining solid oxide fuel cell (SOFC) and oxy-fuel combustion technology is proposed. The system is revised from a pressurized SOFC-gas turbine hybrid system to capture CO₂ almost completely while maintaining high efficiency. The system consists of SOFC, gas turbine, oxy-combustion bottoming cycle, and CO₂ capture and compression process. An ion transport membrane (ITM) is used to separate oxygen from the cathode exit air. The fuel cell operates at an elevated pressure to facilitate the use of the ITM, which requires high pressure and temperature. The remaining fuel at the SOFC anode exit is completely burned with oxygen at the oxy-combustor. Almost all of the CO₂ generated during the reforming process of the SOFC and at the oxy-fuel combustor is extracted from the condenser of the oxy-combustion cycle. The oxygen-depleted high pressure air from the SOFC cathode expands at the gas turbine. Therefore, the expander of the oxy-combustion cycle and the gas turbine provides additional power output. The two major design variables (steam expander inlet temperature and condenser pressure) of the oxy-fuel combustion system are determined through parametric analysis. There exists an optimal condenser pressure (below atmospheric pressure) in terms of global energy efficiency considering both the system power output and CO₂ compression power consumption. It was shown that the integrated system can be designed to have almost equivalent system efficiency as the simple SOFC-gas turbine hybrid system. With the voltage of 0.752 V at the SOFC operating at 900 °C and 8 bar, system efficiency over 69.2% is predicted. Efficiency penalty due to the CO₂ capture and compression up to 150 bar is around 6.1%.     

Design of a methanol reformer for on-board production of hydrogen as fuel for a 3 kW High-Temperature Proton Exchange Membrane Fuel Cell power system

The method of Computational Fluid Dynamics is used to predict the process parameters and select the optimum operating regime of a methanol reformer for on-board production of hydrogen as fuel for a 3 kW High-Temperature Proton Exchange Membrane Fuel Cell power system. The analysis uses a three reactions kinetics model for methanol steam reforming, water gas shift and methanol decomposition reactions on Cu/ZnO/Al₂O₃ catalyst. Numerical simulations are performed at single channel level for a range of reformer operating temperatures and values of the molar flow rate of methanol per weight of catalyst at the reformer inlet. Two operating regimes of the fuel processor are selected which offer high methanol conversion rate and high hydrogen production while simultaneously result in a small reformer size and a reformate gas composition that can be tolerated by phosphoric acid-doped high temperature membrane electrode assemblies for proton exchange membrane fuel cells. Based on the results of the numerical simulations, the reactor is sized, and its design is optimized.     

Autothermal reforming of n-dodecane and desulfurized Jet-A fuel for producing hydrogen-rich syngas

Catalytic reforming is a technology to produce hydrogen and syngas from heavy hydrocarbon fuels in order to supply hydrogen to fuel cells. A lab-scale 2.5 kW_t autothermal reforming (ATR) system with a specially designed reformer and combined analysis of balance-of-plant was studied and tested in the present study. NiO–Rh based bimetallic catalysts with promoters of Ce, K, and La were used in the reformer. The performance of the reformer was studied by checking the hydrogen selectivity, CO_x selectivity, and energy conversion efficiency at various operating temperatures, steam to carbon ratios, oxygen to carbon ratios, and reactants' inlet temperatures. The experimental work firstly tested n-dodecane as the surrogate of Jet-A fuel to optimize operating conditions. After that, desulfurized commercial Jet-A fuel was tested at the optimized operating conditions. The design of the reformer and the catalyst are recommended for high performance Jet-A fuel reforming and hydrogen-rich syngas production.     

Towards autothermal hydrogen production by sorption-enhanced water gas shift and methanol reforming: A thermodynamic analysis

Hydrogen production by the water gas shift reaction (WGS) is equilibrium limited. In the current study, we demonstrate that the overall efficiency of the WGS can be improved by co-feeding methanol and removing CO₂ in situ. The thermodynamics of the water gas shift and methanol reforming/WGS (methanol-to-shift, MtoS) reactions for H₂ production alone and with simultaneous CO₂ adsorption (sorption-enhanced, SEWGS and SEMtoS) were studied using a non-stoichiometric approach based on the minimisation of the Gibbs free energy. A typical composition of the effluent from a steam methane reformer was used for the shift section. The effects of temperature (450–750 K), pressure (5–30 barg), steam and methanol addition, fraction of CO₂ adsorption (0–95%) and energy efficiency of the shift systems have been investigated. Adding methanol to the feed facilitates autothermal operation of the shift unit, with and without CO₂ removal, and enhances significantly the amount of H₂ produced. For a set methanol and CO input, the MtoS and SEMtoS systems show a maximum productivity of H₂ between 523 and 593 K due to the increasing limitation of the exothermic shift reaction while the endothermic methanol steam reforming is no longer limited above 593 K. The heat of adsorption of CO₂ was found to make only a small difference to the H₂ production or the autothermal conditions.     

Combustion chemistry aspects of alternative fuels reforming for high-temperature fuel cell applications

Solid-oxide fuel cells (SOFC) constitute a particularly attractive technology for sustainable, combined heat and power generation, both at domestic and district levels. The elevated operating temperature of SOFC systems, allows the utilization of a wide spectrum of conventional and alternative fuels, through suitable reforming processes. The high temperatures and fuel rich conditions prevailing in SOFC reformers, enhance syngas yield and reforming efficiency but may give rise to unwanted effects, such as ignition, soot and coke formation and deposition. The above phenomena cannot be described via thermodynamic considerations and can only be effectively tackled through a detailed chemical kinetic approach. The present study provides a comparative assessment of SOFC reformer operation on conventional and alternative hydrocarbon fuels in terms of syngas yield, thermal efficiency and pollutants formation. In particular, the reforming of methane, a typical biogas (comprising of 60% CH₄ and 40% CO₂), methanol and ethanol is numerically assessed by utilizing a recently developed and validated comprehensive detailed kinetic mechanism for C₁–C₆ hydrocarbons, augmented with a PAH model. Chemical aspects of the fuel reforming process are investigated through rate-of-production path and sensitivity analyses. The study supports design guidelines aiming towards identification of optimum operating conditions, for specific applications and fuels. The analysis reveals that the extent of coupling between syngas formation and molecular growth processes is strongly dependent on fuel and operating conditions choice and identifies windows of efficient operation, for each case.     

Simulation of steam reforming of biogas in an industrial reformer for hydrogen production

The paper aims to investigate the steam reforming of biogas in an industrial-scale reformer for hydrogen production. A non-isothermal one dimensional reactor model has been constituted by using mass, momentum and energy balances. The model equations have been solved using MATLAB software. The developed model has been validated with the available modeling studies on industrial steam reforming of methane as well as with the those on lab-scale steam reforming of biogas. It demonstrates excellent agreement with them. Effect of change in biogas compositions on the performance of industrial steam reformer has been investigated in terms of methane conversion, yields of hydrogen and carbon monoxide, product gas compositions, reactor temperature and total pressure. For this, compositions of biogas (CH₄/CO₂ = 40/60 to 80/20), S/C ratio, reformer feed temperature and heat flux have been varied. Preferable feed conditions to the reformer are total molar feed rate of 21 kmol/h, steam to methane ratio of 4.0, temperature of 973 K and pressure of 25 bar. Under these conditions, industrial reformer fed with biogas, provides methane conversion (93.08–85.65%) and hydrogen yield (1.02–2.28), that are close to thermodynamic equilibrium condition.