Densification behavior and electrical properties of CuO-doped Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 ternary ceramics

CuO modified Pb(In_1/2Nb_1/2)O₃–Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PIN–PMN–PT) ternary relaxor based ferroelectrics with the composition near the morphotropic phase boundary were synthesized by two-step columbite precursor method. The introduction of CuO significantly improved the sinterability of PIN–PMN–PT ceramics, resulting in the full densification of samples at lower sintering temperatures. It also profoundly modified the crystal structure and fracture mode of the ceramics. Properly increasing CuO content led to the disappearance of rhombohedral-tetragonal phase transition, remarkably improved the Curie temperature (T_c), and made the ceramics more relaxorlike. The ternary ceramics doped with 0.25 wt% CuO possessed optimum piezoelectric properties (d₃₃=584 pC/N, d₃₃^*=948 pC/N, and k_p=0.68), high ferroelectric properties (E_c=9.9 kV/cm, and P_r=33.1 μC/cm²), low dielectric loss (tan δ=0.9%), and wider temperature usage range (T_c=225 °C). The obtained properties are much higher than those of previously reported PIN–PMN–PT based ceramics, indicating that CuO doped PIN–PMN–PT is a promising candidate for electromechanical applications with high performance and wide temperature/electric field usage ranges.     

Dielectric and piezoelectric properties of Pb(Sc1/2Nb1/2)O3–Pb(Ni1/3Nb2/3)O3–PbTiO3 ternary ceramic materials

The dielectric and electrical properties of xPb(Sc_1/2Nb_1/2)O₃–yPb(Ni_1/3Nb_2/3)O₃–zPbTiO₃ (PSNNT 100x/100y/100z) ternary ceramic materials near the morphotropic phase boundary (MPB) were investigated. The MPB follows on almost linear region between PSNNT 58/00/42 and PSNNT 00/68/32 of the binary systems. The maximum electromechanical coupling factor kp=70·7% was found at PSNNT 36/26/38, where ε₃₃^T/ε₀=3019 and Tc=210°C were obtained. These values are similar to those of the Pb(Sc_1/2Nb_1/2)O₃–Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ system and better than those of PZT.     

Domain structure and evolution in ZnO-modified Pb(Mg1/3Nb2/3)O3–0.32PbTiO3 ceramics

The doping of ZnO is efficient to improve the piezoelectric property and thermal stability of Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PMN–PT) based ceramics. However, the underlying physics, especially the local domain structures of the ZnO modified PMN–PT ceramics, which is strongly associated with the electric properties, is not clear yet. In this paper, we investigated the local domain structures and their evolution as a function of x in PMN–0.32PT:xZnO ceramics. It was found that, the domain evolution is mainly caused by the growth of grain size induced by the sintering aiding effect of ZnO at x < 0.04, and the domain evolution can be attributed to the phase transition induced by the partial replacement of Mg²⁺ by Zn²⁺ in the B-site of PMN–PT lattice at x > 0.06. Furthermore, we also investigated the domain structure evolution as functions of temperature and local external electric field in PMN–0.32PT:0.06ZnO ceramics, which exhibited superior piezoelectric property relative to other compositions. We found that the irregular nanodomains are more stable at high-temperature range, and the regular non-180° domains exhibited more complex rotation behavior under local electric field, which probably leads to the thermal stability and piezoelectric property enhancement in the ZnO-modified PMN–0.32PT ceramics.     

Modified Pb(Mg1/3Nb2/3)O3-PbZrO3–PbTiO3 ceramics with high piezoelectricity and temperature stability

There is a great demand to develop ferroelectric ceramics with both high piezoelectric coefficient and broad temperature usage range for emerging electromechanical applications. Herein, a series of Sm³⁺-doped 0.25Pb(Mg_1/3Nb_2/3)O₃-(0.75−x)PbZrO₃-xPbTiO₃ ceramics were fabricated by solid-state reaction method. The phase structure, dielectric and piezoelectric properties were investigated, where the optimum piezoelectric coefficient d₃₃ = 745 pC/N and electromechanical coupling factor k₃₃ = 0.79 were obtained at the morphotropic phase boundary composition x = 0.39, with good Curie temperature T_C of 242°C. Of particular importance is that high-temperature stability of the piezoelectric and field-induced strain was obtained over the temperature range up to 230°C for the tetragonal compositions of x = 0.40. The underlying mechanism responsible for the high piezoelectricity and temperature stability is the synergistic contribution of the MPB and local structural heterogeneity, providing a good paradigm for the design of high-performance piezoelectric materials to meet the challenge of piezoelectric applications at elevated temperature.     

Relaxation behavior in 0.24Pb(In1/2Nb1/2)O3–0.49Pb(Mg1/3Nb2/3)O3–0.27PbTiO3 ferroelectric single crystal

Dielectric relaxation properties of the ternary relaxor-based ferroelectric 0.24Pb(In_1/2Nb_1/2)O₃–0.49Pb(Mg_1/3Nb_2/3)O₃–0.27PbTiO₃ single crystal have been investigated as a function of temperature (300–570 K) in the frequency range from 100 Hz to 100 kHz. It was found that the variation of the permittivity maximum temperature T_m with frequency obeys the Vogel–Fulcher relationship. The high-temperature (T>T_m) side of the dielectric permittivity deviated from the Curie–Weiss law, but can be described by the Lorenz-type relationship. The coercive field obtained from the polarization hysteresis loops gradually decreases with increasing temperature, and the remnant polarization persists above T_m due to the existence of polar nanoregions (PNRs).     

Electrocaloric properties of 0.7Pb(Mg1/3Nb2/3)O3–0.3PbTiO3 ceramics with different grain sizes

We have investigated the electrocaloric (EC) properties of the ceramic 0.7Pb(Mg_1/3Nb_2/3)O₃–0.3PbTiO₃. A variety of samples with different median grain sizes, i.e., 1.0, 2.2 and 4.0?μm, and relative densities of about 96% were prepared using atmospheric sintering at 1200^oC for 2, 8 and 16?h. The ceramic material with a median grain size of 2.2?μm exhibited the highest value for the EC temperature change, i.e., 1.27?K at 60?kV?cm^?1, measured with a high-resolution calorimeter. This value is 25 and 19% higher than the value for the ceramics with the finer and the coarser grains, respectively.     

High pyroelectric response in Pb0.99Nb0.02[(Zr0.57Sn0.43)1−xTix]0.98O3 ceramics

Both high pyroelectric coefficient and figure of merits of ferroelectric materials are desirable for infrared detection. In this work, we prepared Pb_0.99Nb_0.02[(Zr_0.57Sn_0.43)_1−xTi_x]_0.98O₃ (0.060 ≤ x ≤ 0.080) ceramics, and the microstructure and electric properties were studied systematically. It is observed that the composition x = 0.07 shows enhanced pyroelectric properties around ambient temperature due to the ferroelectric–antiferroelectric phase transition, with the pyroelectric coefficient p = 6.83 × 10⁻⁴ C m⁻² K⁻¹ and the figures of merit F_i = 5.04 × 10⁻¹⁰ m V⁻¹, F_v = 7.61 × 10⁻² m² C⁻¹, and F_d = 3.46 × 10⁻⁵ Pa^−1/2 at room temperature and the highest pyroelectric coefficient of 695.5 × 10⁻⁴ C m⁻² K⁻¹ and F_i = 1410.46 × 10⁻¹⁰ m V⁻¹, F_v = 1587.39 × 10⁻² m² C⁻¹, and F_d = 1182.94 × 10⁻⁵ Pa^−1/2 at 36.7°C. These values are superior to other pyroelectric materials. These results indicate that this system is a promising pyroelectric material for the applications of infrared detectors.     

Preparation,structure, and electric properties of the Pb(Zn1/3Nb2/3)O3–Pb(Yb1/2Nb1/2)O3–PbTiO3 ternary ferroelectric system ceramics near the morphotropic phase boundary

Ceramics of the xPb(Zn_1/3Nb_2/3)O₃–(1 ? x ? y)Pb(Yb_1/2Nb_1/2)O₃–yPbTiO₃ (PZN–PYN–PT) ternary system were synthesized using a modified two-step columbite precursor method which can effectively suppress the pyrochlore phase. A morphotropic phase boundary (MPB) region, separating tetragonal and rhombohedral phases in the ternary systems has been determined. The electric properties of the compositions near MPB region were investigated. Dielectric response exhibits relaxor-like characteristics with broad dielectric peaks and dispersive dielectric behavior with respect to frequency and temperature. The phase diagram of the 0.45PZN–(0.55 ? y)PYN–yPT pseudo-binary system in the composition range of 0.15 < y < 0.35 was established based on dielectric measurements. The optimal properties were achieved in the MPB composition of 0.52PZN–0.21PYN–0.27PT with piezoelectric coefficient d₃₃, dielectric permittivity ε′, planar electromechanical coupling k_p, dielectric loss tan δ, coercive field E_c, remnant polarization P_r, and T_C being of 558 pC/N, 2065, 62%, 0.2%, 19.88 kV/cm, 31.44 μC/cm² and 259.5 °C, respectively, showing potential usage in high-temperature electromechanical applications.     

Large-strain 0.7Pb(ZrxTi1−x)O3–0.1Pb(Zn1/3Nb2/3)O3–0.2Pb(Ni1/3Nb2/3)O3 piezoelectric ceramics for high-temperature application

0.7Pb(Zr_xTi_1−x)O₃–0.1Pb(Zn_1/3Nb_2/3)O₃–0.2Pb(Ni_1/3Nb_2/3)O₃ (0.7PZT–0.1PZN–0.2PNN, x = 0.44–0.47) piezoelectric powders and ceramics have been prepared through conventional solid-state reaction method. Outstanding piezoelectric and dielectric properties occurred at the morphotropic phase boundary (MPB), which was characterized by the X-ray diffraction spectrum. The MPB composition (x = 0.46) performed high d₃₃ value (641 pC/N), indicating that the system suited large-strain application. The field-induced strain reached 0.25% under a considerably low electric field (0.8 kV/mm) according to the bipolar strain *S–E loops. The effect of the grain size on the aging phenomenon and temperature stability has also been investigated. Due to higher Curie temperature and smaller grain size, the 0.7PZT–0.1PZN–0.2PNN ceramics maintained a high d₃₃ level after depoling treatment, revealing a superior strain capacity for high-temperature application.     

Investigation of dielectric and piezoelectric properties in Pb(Ni1/3Nb2/3)O3–PbHfO3–PbTiO3 ternary system

The dielectric and piezoelectric properties were investigated in the (1 ? x)Pb(Hf_1?yTi_y)O₃–xPb(Ni_1/3Nb_2/3)O₃ (PNN–PHT, x = 0.05–0.50, y = 0.55–0.70) ternary system. The morphotropic phase boundary (MPB) was determined by X-ray powder diffraction analysis. Isothermal map of Curie temperature (T_C) related to the compositions in the phase diagram was obtained. The optimum dielectric and piezoelectric properties were achieved in ceramics with the MPB compositions, with the maxima values being on the order of 6000 and 970pC/N, respectively. Rayleigh analysis was used to study the extrinsic contribution (domain wall motion) in PNN–PHT system, where the extrinsic contribution was found to be ～30% for composition 0.49PNN–0.51PHT(30/70), showing a high nonlinearity.     

Electrical properties of Sb and Cr-doped PbZrO3–PbTiO3–PbMg1/3Nb2/3O3 ceramics

The pyroelectric, dielectric and DC resistive properties of Sb and Cr-doped ceramics with a base composition of Pb(Mg_1/3Nb_2/3)_0.025(Zr_0.825Ti_0.175)_0.975O₃ have been studied. Sb doping has been shown to produce a linear reduction in Curie temperature (T_C=−22z+294 °C) with concentration (z) and to give an increase in pyroelectric coefficient from 250 to 310 μCm⁻² K⁻¹ for z increasing from 0 to 3 at.%. It also produces first a reduction and then an increase in both dielectric constant and loss, so that the 33 Hz pyroelectric figures of merit (FOM's) are as follows: F_V peaks at 3.8×10⁻² m² C⁻¹ and F_D peaks at 1.2×10⁻⁵ Pa^−1/2. The resistivity is increased substantially from 1.1×10¹¹ to ca 6×10¹¹ Ωm with 1 at.% Sb, thereafter changing little. The behaviour has been explained in terms of Sb acting as a donor ion, reducing oxygen vacancy concentrations up to 1 at.%, with conductivity dominated by hole hopping between traps (E_a=0.59±0.05 eV) that are not changed by the Sb doping. It is concluded that additions of higher levels of Sb do not produce electron-mediated hopping conduction. The Cr additions have no effect upon T_C, but reduce dielectric constant and loss, pyroelectric coefficient and resistivity at doping levels up to 3 at.%. The FOM F_V peaks at 3.6×10⁻² m² C⁻¹ and F_D at 1.9×10⁻⁵ Pa^−1/2. The behaviour of the electrical resistivity as a function of dopant level is shown to produce a linear ln(σ_o) vs z^−1/3 dependence (σ_o=DC conductivity), as would be expected for hole hopping conduction between Cr³⁺ sites, with an E_a=0.38±0.03 eV.     

Characterization of 0.93Pb(Zn1/3Nb2/3)O3–0.07BaTiO3 ceramics derived from a novel Zn3Nb2O8 B-site precursor

In this work, perovskite relaxor ferroelectric lead zinc niobate–barium titanate (0.93PZN–0.07BT) ceramics were fabricated by using a combination of Zn₃Nb₂O₈ B-site precursor and reactive sintering process. The effects of sintering condition on phase formation, densification, microstructure and dielectric properties of the final products have been investigated using a combination of X-ray diffraction, Archimedes density measurement, scanning electron microscopy and dielectric measurement techniques. It is seen that pure perovskite phase of PZN-BT solid solutions can be achieved in all samples. Density and average grain size values of sintered samples increased with sintering temperatures and dwell time. With appropriate sintering at 1150 °C for 5 h, 0.93PZN–0.07BT ceramics exhibited a peak dielectric constant of 11,497 and dielectric loss of 0.05 at the Curie temperature of 99 °C measured at 1 kHz.     

A new Pb(Lu1/2Nb1/2)O3–PbZrO3–PbTiO3 ternary solid solution with morphotropic region and high Curie temperature

A ceramic ternary system of (1?x?y)Pb(Lu_1/2Nb_1/2)O₃–xPbZrO₃–yPbTiO₃ (PLuN–PZ–PT) has been prepared by two-step synthetic process and characterized by X-ray powder diffraction and electric measurements. A morphotropic phase boundary (MPB) region has been delimited in the ternary system at room temperature. With the PLuN content increasing, the morphotropic phase boundary region becomes broad as well as the dielectric peak. The best comprehensive piezoelectric properties were achieved at MPB composition 0.42PLuN–0.1PZ–0.48PT, with the piezoelectric coefficients d₃₃, the Curie temperature T_c, the planar electromechanical coupling factor K_p, and the remnant polarizations P_r being 367 pC/N, 360 °С, 68% and 35 μС/cm², respectively. The results indicate that the PLuN–PZ–PT ternary ferroelectric material may be a promising candidate for high-power electromechanical transducers that can operate in a large temperature range.     

Broadband dielectric spectroscopy of PbMg1/3Nb2/3O3–PbSc1/2Nb1/2O3 ceramics

Broadband dielectric spectroscopy results of various ordered and disordered (1 ? x)Pb(Mg_1/3Nb_2/3)O₃–(x)Pb(Sc_1/2Nb_1/2)O₃ (PMN–PSN) ceramics are investigated in the temperature range from 80 K to 300 K and frequency range from 20 Hz to 2 THz. Dielectric dispersion is very broad and in the ferroelectrics case (x = 1, 0.95) consists of two parts: low-frequency part caused by ferroelectric domains and higher frequency part caused by soft mode. The relaxational soft mode exhibits pronounced softening close to phase transition temperature, as it is typical for order–disorder phase transitions. By substituting Sc³⁺ by Mg²⁺ in PMN–PSN ceramics relaxation slows down, and for relaxors (x = 0.2) the most probable relaxation frequency decreases on cooling according to Vogel–Fulcher law.     

Effect of Ba(Zn1/3Nb2/3)O3 modification on structure and ferroelectric properties of 0.6Pb(Mg1/3Nb2/3)O3–0.4Pb(Zr0.52Ti0.48)O3 ceramics

In this study, (1−x)[0.6Pb(Mg_1/3Nb_2/3)O₃–0.4Pb(Zr_0.52Ti_0.48)O₃]–xBa(Zn_1/3Nb_2/3)O₃; (1−x)PMNZT60/40–xBZN having x=0, 2.5, 5, 7.5, and 10 mol% ceramics were prepared by mixed oxide powder method and sintered using a two-step process. Phase transitions were investigated by XRD, microstructure by SEM, crystal morphology by TEM, the dielectric and ferroelectric properties by capacitance measurement setup and modified Sawyer-Tower circuit, respectively. The dielectric constant and dielectric loss tangent were measured as functions of both temperature and frequency. The XRD results show the phase transition from tetragonal phase to pseudo-cubic phase with addition of BZN in PMNZT system. Grain size of about 1.23–2.42 μm and crystallite size in a range of 421–2152 nm were obtained. The pure-phase 0.6PMN–0.4PZT ceramics show the normal ferroelectric behavior. The 0.95(PMNZT60/40)–0.05BZN and 0.925(PMNZT60/40)–0.075BZN showed a broad and diffused dielectric properties and the dispersive phase transition, indicating the relaxor ferroelectric behavior. The transition temperature in the BZN-modified PMNZT system is seen to decrease from 166 °C in pure PMNZT60/40 to 102 °C and 54 °C with increasing BZN content to 5 and 10 mol%, respectively. In addition, the maximum dielectric constant is decreased with increasing BZN content. The P–E hysteresis loop measurements show the change from the normal ferroelectric behavior in PMNZT60/40 ceramic to more relaxor behavior that was induced with BZN addition. These results clearly demonstrated the significance of BZN to the electrical responses of the PMNZT60/40 system.     

Crystal structure and piezoelectric properties of xPb(Mn1/3Nb2/3)O3–(0.2 − x)Pb(Zn1/3Nb2/3)O3–0.8Pb(Zr0.52Ti0.48)O3 ceramics

Pb(Mn_1/3Nb_2/3)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Zr_0.52Ti_0.48)O₃ (designated as PMnN–PZN–PZT) piezoelectric ceramics were prepared and the effects of PMnN content on the crystal structure and electrical properties were investigated. The results show that the pure perovskite phase forms in these ceramics. The crystal structure changes from tetragonal to rhombohedral and the lattice constant decreases with increase of PMnN content. The morphotropic phase boundary (MPB) of xPMnN–(0.2 ? x)PZN–0.8PZT ceramics occurs where the content of PMnN, x, lies between 0.05 and 0.085 mol. The dielectric constant (?), piezoelectric constant (d₃₃) and Curie temperature (T_c) decrease, while the mechanical quality factor (Q_m) increases with the increase of PMnN content. The ceramic with composition 0.075PMnN–0.125PZN–0.8PZT has the optimal piezoelectric properties, ? is 842, d₃₃ is 215 pC/N, T_c is 320 °C, k_p is 0.57 and Q_m amounts to 1020, which makes it a promising material for high power piezoelectric devices.     

A new multiferroic ternary solid solution system: NdFeO3–Pb(Fe1/2Nb1/2)O3–PbTiO3

Ceramic materials were sintered from powders of the NdFeO₃–Pb(Fe_1/2Nb_1/2)O₃–PbTiO₃ (NF–PFN–PT) ternary system synthesized by the conventional solid reaction method and their multiferroic properties investigated. The structure, electric and magnetic properties of the ternary system have been investigated. The introduction of Pb(Fe_1/2Nb_1/2)O₃ into the NdFeO₃–PbTiO₃ binary system can effectively increase its electric properties. The ternary system exhibits enhanced piezoelectric property with optimal piezoelectric constants d₃₃=143 pC/N, reduced coercive fields E_C=5.78 kV/cm and remnant polarization P_r=12.8 μC/cm² for 0.10NF–0.56PFN–0.34PT, near tetragonal phase region. The Curie temperature (T_C) of the NdFeO₃–Pb(Fe_1/2Nb_1/2)O₃–PbTiO₃ ceramics varies in the range from 108.7 °C to 67.9 °C. The magnetic hysteresis loops show that the ternary system is paramagnetic originating from canting of paramagnetic sublattices in NF–PFN–PT, due to the rare earth ions Nd³⁺ influencing on the exchange interaction between Fe³⁺ ions at the octahedral sites.