LDPE／PS／LDPE—g—PS合金的相容性和力学性能研究

研究自制接枝共聚物ＧＲ－１，ＧＲ－Ⅱ相容剂对ＬＤＰＥ／ＰＳ共混物相容性和力学性能的影响，通过ＳＥＭ，ＤＭＡ和力学性能测试表征，表明在ＬＤＰＥ／ＰＳ共混中加入这些相容剂后，其相容性有一定提高，共混物结构形态呈精细分散结构。3     

HDPE／PS／HDPE－g－PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ⅰ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ、ＤＳＣ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高     

HDPE／PS／HDPE—g—PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ｉ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高。     

用MBO(口恶)唑啉合成LDPE/PS合金相容剂及其对合金的增容作用

采用１,３－双－（恶唑啉基）－苯为偶联剂通过反应性加工实现ＰＳ－ｇＭＡｎ和氯化聚乙烯之间反应方法来合成ＬＤＰＥ／ＰＳ共混体系相容剂,在ＬＤＰＥ／ＰＳ共混体系中加入１０％此相容剂,其冲击强度提高２．３倍,拉伸强度和弯曲强度也有所提高。通过ＳＥＭ、ＤＭＡ和ＤＳＣ分析表征表明加入此相容剂后,ＬＤＰＥ／ＰＳ共混物的相容性有显著改善。     

RPS/PE反应性共混研究

用ＩＲ、ＤＳＣ、ＧＰＣ研究了侧基含有过氧键的活性聚苯乙烯与聚乙烯之间的反频，用ＳＥＭ观察了共混物的断面形态。结果表明，ＲＰＳ／ＰＥ共混反应中生成ＰＳ－ｇ－ＰＥ，对ＰＥ／ＰＳ共混物具有增容作用，提高了共混物的力学性能。     

离聚物对PET／LDPE共混物的结构与性能研究

用双螺杆挤出机反应性挤出的方法合成了低密度聚乙烯接枝马来酸镧（ＬＤＰＥ－ｇ－ＭＡＬａ）离聚物。与其它方法相比，该法具有工艺简单，易于工业化生产的特点。我们将离聚物与ＰＥＴ，ＬＤＰＥ在双螺杆挤出机上熔融共混挤出，并用注射成型机制备标准样条，对共混物力学性能进行了测试，发现离聚物有显著的增韧效果，另外，通过ＩＲ，ＤＳＣ，溶解性实验，分子量的测定等还考察了离聚物对ＰＥＴ／ＬＤＰＥ共混体系的结构影响。     

LDPE对PBT／PC共混体系性能的影响

研究发现，在ＰＢＴ／ＰＣ共混体系中加入少量熔体指数（ＭＩ）较大的低密度聚乙烯（ＬＤＰＥ），可以改善该共混体系的加工成型性能、外观及力学性能。随着ＬＤＰＥ含量的增加，ＰＢＴ／ＰＣ巫混物的溶体指数增大；ＬＤＰＥ对共混体系还可起增韧作用，ＬＤＰＥ的加入使共混物的缺口冲击强度有明显的提高。另外，ＤＳＣ研究发现，ＬＤＰＥ的引入对共混物中ＰＢＴ组分的结晶有明显的促进作用，并使ＰＣ的玻璃化转变温度Ｔｇ下降。热失     

固相法CPE增容PVC／LDPE共混体系的研究

通过力学性能试验、动态力学分析（ＤＭＡ）、电子显微镜观察，研究了固相法氯化聚乙烯（ＣＰＥ）对聚氯乙烯（ＰＶＣ）与低密度聚乙烯（ＬＤＰＥ）共混体系的增容作用。实验结果表明，ＣＰＥ的加入能明显改善ＰＶＣ／ＬＤＰＥ共混体系的相容性，显著提高共混物的力学性能，且低温氯化制得的ＣＰＥ的改善效果优于两段氯化制得的ＣＰＥ。电子显微镜观察表明，增容剂增加了共混体系相间相互作用或相界面粘附性，对共混体系的形态结构产     

PET／HDPE共混物的形态结构及力学性能的研究

利用ＩＲ、ＳＥＭ、ＤＳＣ和力学测试等分析方法，研究了熔融接枝高密度聚乙烯（ＨＤＰＥ－ｇ－ＭＡ）和界面改性剂（ＩＭ）对ＰＥＴ／ＨＤＰＥ共混物形态结构、界面偶联状况和力学性能的影响。结果在明，ＨＤＰＥ－ｇ－ＭＡ改善了ＰＥＴ与ＨＤＰＥ的相容性，使ＨＤＰＥ较均匀地分散在ＰＥＴ基体中，但并未检测到ＰＥＴ／ＨＤＰＥ－ｇ－ＭＡ界面有化学反应发生。界面改性剂的作用在于，一方面通过提高ＰＥＴ基体的粘度，并接近ＨＤＰＥ相的粘度而使分散相细化；另一方面通过与ＨＤＰＥ－ｇ－ＭＡ和ＰＥＴ的偶联反应而增强了ＰＥＴ／ＨＤＰＥ－ｇ－ＭＡ界面粘结，从而显著地提高了共混物的抗冲击性能。     

HPB－b－PMMA增容PVC／PE共混物球晶和结晶行为研究

以小角激光散射（ＳＡＬＳ）和广角Ｘ光衍射（ＷＡＸＤ）技术，测定了氢化聚丁二烯－聚甲基丙烯酸甲基嵌段共聚物（ＨＰＢ－ｂ－ＰＭＭＡ）增容的聚氯乙烯（ＰＶＣ）和聚乙烯（ＰＥ）共混物的球晶形态和结晶度。从该共混物中ＰＥ的结晶状况得出，增容剂ＨＰＢ－ｂ－ＰＭＭＡｄ在降低ＰＥ结晶能力、增加ＰＥ／ＰＶＣ界面粘合并形成ＰＶＣ和ＰＥ相间的部分相容性有着重要的作用。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to