The effects of contact configuration and coating morphology on the tribological behaviour of tetrahedral amorphous diamond-like carbon (ta-C DLC) coatings under boundary lubrication

ABSTRACT

Tribological studies were carried out with tetrahedral amorphous diamond-like carbon (ta-C DLC) coatings, varying in thickness and roughness, using two different contact configurations lubricated with seven types of hydraulic oils. Tribopair of cast iron and ta-C coated steel were tested in both non-conformal and conformal, unidirectional sliding contacts. The friction and wear results were mainly affected by the thickness of the coating in the non-conformal contact and the surface roughness of the coating in the conformal contact. Tests done with mineral base oil containing rust inhibitor in the non-conformal contact and with Polyalphaolefins and synthetic ester base oils in the conformal contact resulted in the lowest friction while that with mineral base oil containing zinc resulted in high friction and counterface wear. The results highlight the interdependence of contact configuration, lubricant chemistry, coating’s surface morphology and coating’s thickness in determining the tribological behaviour of ta-C coatings under boundary lubrication.     

Behaviour of MoDTC in DLC/DLC and DLC/steel contacts

Diamond-like carbon (DLC) coatings are beginning to be used on machine components parts because of their excellent friction and wear resistance properties. It is hence important to be able to formulate lubricants able to work effectively with these coatings. This requires knowledge of how the various surface-reactive additives generally employed in lubricants behave with DLCs. This paper compares the behaviour of seven types of DLC, a-C, a-C:H, a-C:H:W, a-C:H:WC, Si-DLC, ta-C, ta-C:H, lubricated with molybdenum dialkyldithiocarbamate (MoDTC) solution. It is found that a-C and a-C:H:WC give lower boundary friction than the other types of DLC. MoDTC improves the wear resistance of DLC/DLC contacts but appears to greatly degrade the wear resistance properties of some DLCs in DLC/steel contacts, even though Mo-derived tribofilms form on all DLCs.     

Development of amorphous carbon coating with luminescent silica/CdSe/ZnS quantum dots underlayer for wear monitoring

Amorphous carbon (a-C) coating with luminescent wear-sensing underlayer is developed for achieving the tribological coating with wear monitoring capability. Wear monitoring of a-C coating by luminescent spectroscopy to determine the remaining thickness of the coating after the wear test is also demonstrated. The coating structure consists of a-C films deposited by R.F. magnetron sputtering method onto the luminescent layer, which is made from silica coating containing CdSe/ZnS quantum dots (Silica/QD). A thin Si-intermediate layer is added between a-C and silica/QD layer for adhesion improvement. The physical as well as tribological properties of the coatings are analysed. Furthermore, wear monitoring of a-C films is also demonstrated to determine the remaining coating thickness after the tribological test. The demonstration is carried out by firstly formulating a relation between luminescent intensity detected from the coating and coating thickness. Then the luminescent intensity is measured again from the wear track. The remaining thickness is finally determined by using the relationship between luminescent intensity and coating thickness. The fabricated coating exhibits a smooth surface with the average surface roughness of 1.35 nm and a friction coefficient of 0.1. The demonstration of wear monitoring shows that the remaining thickness of the coating after the tribological test determined by luminescent spectroscopy is compared well with the thickness measured by profilometry. This suggests that wear monitoring of a-C films by luminescent spectroscopy technique is feasible.     

Tribological Properties of DLC Coatings in Helium

The aim of this research work was to investigate tribological properties of low-friction DLC coatings when operating in helium atmosphere. Two commercial DLC coatings (a-C:H and Me-C:H) were included in the investigation and compared to reference PTFE-based coatings, normally used on components operating in helium. Coatings were deposited on hardened 100Cr6 bearing steel discs and tested against uncoated steel balls in low-load pin-on-disc contact configuration. Investigation was focused on the effect of substrate roughness (R _a ?=?0.05?C0.2???m) and contact conditions, including contact pressure (150?C350?MPa) and sliding speed (0.2?C0.4?m/s) on the coefficient of friction of DLC coatings operating in helium. Results of this investigation show that for low-load sliding contact DLC coatings provide low friction in helium atmosphere, similar to soft PTFE-based coatings. At the same time DLC coatings investigated were found to substantially reduce wear of the coated surface. However, while the wear of the coated part has been more or less eliminated, application of DLC coating prolongs running-in and increases wear of the steel counter-part. Furthermore, also in helium atmosphere tribolgical behaviour of DLC coatings showed dependence on the coating type and contact conditions.     

Influence of Silicon on the Wear Properties of Amorphous Carbon Under Dry and Lubricated Conditions

Diamond-like carbon (DLC) coatings have drawn much attention as potential surface coatings for engineering contacts because of their excellent friction and wear resistance properties. However, much less is known about their friction and wear mechanisms, especially at higher contact pressures. In this study, two amorphous carbon DLCs, with (a-C:Si) and without Si (a-C), have been investigated to understand the influence of Si on friction and wear under dry, base oil- and fully formulated oil-lubricated conditions. Si does not affect friction but significantly affects wear. a-C:Si shows lower wear than a-C but imparts higher wear on the steel counterpart. The steel counterpart that forms a hybrid tribolayer (transferred carbon from DLC + additive-derived tribofilm products) exhibits superior wear resistance properties.     

Influence of Surface Roughness on the Transfer Film Formation and Frictional Behavior of TiC/a-C Nanocomposite Coatings

Influence of surface roughness on the friction of TiC/a-C nanocomposite coatings while sliding against bearing steel balls in humid air was examined by detailed analyses of the wear surfaces and the wear scar on the ball counterparts by atomic force microscopy, optical, and confocal microscopy. It was observed that the surface roughness of the coatings essentially determines the wear behavior of the ball counterpart, which consequently influences the transfer film formation. A rough coating causes abrasive wear of the steel ball during the running-in period, which impedes the formation of a stable transfer film and leads to higher values of coefficient of friction (CoF). Moreover, the CoF does not show a decreasing trend after the running-in period, although the roughness of the coating was greatly reduced. Replacing the worn ball with a new one after the running-in period yields lower CoF values similar to that observed for a smooth coating. In both of the cases, no wear of the steel ball occurs and a stable transfer film forms and effectively covers the contact area. The influence of the wear debris on the formation of the transfer film is also discussed.     

Low-friction carbon-rich carbide coatings deposited by co-sputtering

Low-friction coatings are used more and more frequently, particularly in situations and applications with insufficient or no lubrication. A good example of such coatings is amorphous carbon, which is produced both in pure form (a-C:H) and doped with metal (Me-C:H). The knowledge of what actually occurs when one metal in a Me-C:H coating is exchanged with another has so far been rather limited. Also, when producing these films hydrogen is incorporated in the substrate as well as in the film, which can be detrimental to the overall properties.Here, a newly adopted co-sputtering technique, utilizing a carbon target partly covered by metal-foil strips, was used to deposit non-hydrogenated carbon coatings alloyed with Ta, W and Zr on ball-bearing steel (BBS) substrates. The metal content varied between 0 and 41 at.%, and the resulting films were analyzed with respect to phase composition and textures, chemical composition, microstructural morphology, as well as mechanical and tribological properties. All alloyed coatings displayed a nanocomposite microstructure, with 3-6 nm metal-carbide crystallites embedded in a matrix of amorphous carbon. The amount of metal-carbide phase increased with increasing amounts of metal which led to a large increase in hardness and elastic modulus. An increased metal content did however not affect the carbide size to any notable extent. Ball-on-disk tests show that metal additions cause a sharp drop in friction coefficient from 0.21 to about 0.05, depending on the metal used. This is however accompanied by an increase in wear rate. The coating best combining low friction and low wear rate was alloyed with 20 at.% Ta. Best possible protection of the counter surface was offered by coatings containing 30 at.% Ta or more.     

Influence of humidity on the friction of diamond and diamond-like carbon materials

The friction of diamond and diamond-like carbon (DLC) materials was evaluated in reciprocating sliding wear testing under controlled relative humidity. The testing conditions were a displacement stroke of 100 μm, an oscillatory frequency of 8 Hz and a normal load of 2 N. The coefficient of friction of diamond and hydrogen-free DLC (a-C) coatings against a corundum sphere in the steady regime decreased with an increase in relative humidity. A water layer physisorbed at the interface between the mating surfaces played two major roles: acting as a lubricant and increasing the true area of contact. However, it was noticed that the friction coefficient of the hydrogenated DLC (a-C:H) coatings first increased and then decreased with increasing relative humidity in the steady state. There appeared to be a critical relative humidity for the a-C:H coatings, at which the steady-state friction reached the maximum value. The frictional behaviour of the a-C:H coatings also showed dependence on the wear test duration. The interaction between hydrogen and oxygen at the interface between the a-C:H coating and water layer was mainly responsible for such behaviour.     

Friction and wear behaviour of hard coatings in vibrating contacts

The friction and wear behaviour of thin hard coatings, such as TiN and the promising class of C-based coatings (a-C, a-C:H, and diamond for example), are compared under oscillating and reciprocating sliding conditions. The typical effects of test parameters, such as stroke, frequency, normal force, relative humidity and test duration, are described as a basis for the proper selection of test conditions or, conversely, for the selection of suitable coatings for particular practical applications. Friction and wear data from over 1000 vibrating tests using thin hard coatings against 100Cr6 and against Al₂O₃ have been compiled in a database. This allows easy manipulation and comparison of test results. Using selection criteria and filter procedures (e. g., lifetime of coatings, friction limits, and critical wear rate), suitable coating systems for different test conditions can be chosen from the database. The effects of test parameters on friction and wear behaviour and changes have anyway to be known for meaningful tribotesting, as well as for the selection of coatings.     

硬质合金刀具高能离子源增强多弧镀AlCrTiSiN梯度涂层制备及性能研究

采用离子源增强的多弧离子镀新技术,在硬质合金刀具表面制备了不同含Si层梯度结构的AlCrTiSiN梯度涂层,并对涂层组织结构、残余应力、结合强度、摩擦磨损以及铣削和钻削加工灰铸铁性能进行了详细的研究。结果表明：不同含Si层梯度结构的AlCrTiSiN涂层主要由固溶的(Al,Cr) N、(Al,Ti) N相和非晶态Si₃N₄相组成。其中,含Si层梯度变化最缓和的G3(Gradient 3)涂层具有较高的结合强度,较低的残余压应力、摩擦因数和磨损率。铣削和钻削试验显示,涂层刀具的切削磨损机理主要表现为磨粒磨损和粘着磨损。G3涂层降低了磨粒磨损,其刀具的铣削和钻削寿命均最高,这主要得益于其含Si层的梯度设计、适当的压应力(-3.8 GPa)以及良好的膜基结合强度。研究结果表明,通过对含Si层进行梯度设计可显著提高涂层刀具的切削性能。     

Structure and water-lubricated tribological properties of Cr/a-C coatings with different Cr contents

The Cr containing amorphous carbon coatings (Cr/a-C) with varying Cr content were deposited using unbalanced magnetron sputtering. The results revealed that the chromium carbide nano-clusters were formed when the Cr content exceeded 4.9 at%. The critical load increased while the hardness decreased after the Cr element incorporation. Although the low Cr containing Cr/a-C coatings (≤4.9 at%) exhibited similar friction coefficient with a-C coatings, but the initial friction coefficient, running-in distance and wear rate of SUS440C balls all decreased. However, the Cr/a-C coatings with high Cr content (11.98–14.09 at%) would worsen the tribological properties because chromium carbides acted as abrasive wear particles during tribotests.     

Wear Resistance of Coated SAE 305 Aluminum Alloy Under Dry Friction Reciprocate Sliding

This work investigates the influence of two coatings on the wear resistance of the SAE 305 aluminum alloy. This material is widely used in power transmission components, and improvement in its surface properties can lead to remarkable impacts in the energy sector. The tested treatments are: (1) anodization and (2) diamond-like carbon coating. Dry friction reciprocate sliding tests using a sphere-on-plane configuration are presented. The untreated reference surface and both treatments are evaluated regarding their roughness, hardness, coefficient of friction, wear rate and morphology. The surface analyzes were carried out using confocal laser and SEM techniques. In comparison with the reference, the diamond-like carbon coating showed a significantly higher wear resistance, whereas the anodization process showed only a minor improvement.     

Tribological Behavior of TiC/a-C:H-Coated and Uncoated Steels Sliding Against Phenol–Formaldehyde Composite Reinforced with PTFE and Glass Fibers

Tribological experiments on phenol–formaldehyde composite reinforced with polytetrafluoroethylene (PTFE) and glass fibers were performed against 100Cr6 steel and TiC/a-C:H thin film-coated 100Cr6 steel. In both cases, the coefficient of friction increases with increasing sliding distance until a steady-state value is reached. Although the steady-state values of the coefficient of friction are very close and ultralow, the wear rate of the PTFE composite liner at a long sliding distance (1,000 m) is reduced when the steel ball is coated with the TiC/a-C:H coating. This behavior is mainly attributed to the smoother surface after long sliding and the improved wear resistance of TiC/a-C:H coating. PTFE transfer films are evident on the surfaces of the hard counterparts. The average thickness of the transfer film on TiC/a-C:H-coated surfaces is about 3.8 nm. On the surface of uncoated steel ball, a continuous but non-uniform transfer film of around 13.9 nm average thickness was found.     

Tribochemical effects on the friction and wear behaviors of a-C:H and a-C films in different environment

Friction and wear behaviors of hydrogenated amorphous carbon (a-C:H) and hydrogen-free amorphous carbon (a-C) films sliding against Si₃N₄ balls were investigated in different testing environments. The result showed that two films with extreme chemical disparity (one hydrogenated, and the other hydrogen free) showed distinct different friction and wear behaviors, and the friction and wear behaviors of the both films were strongly dependent on the environment. For a-C:H films, much low friction coefficient and wear rate were obtain in dry N₂. In the water and/or oxygen containing environments, the friction coefficient and wear rate of a-C:H films were obviously increased. On the contrary, a-C films only provided low friction coefficient and wear rate in the presence of water and/or oxygen in the test chamber. In dry N₂, the highest friction coefficient and wear rate were observed for a-C films. By investigating the worn surfaces of the films using XPS, it was proposed that the environment dependence of the friction and wear behaviors of the films was closely related with the friction-induced chemical interactions between the films and water and/or oxygen molecules. The specific roles of hydrogen, water and oxygen molecules and their tribochemical effects on the friction and wear mechanism of the films are discussed.     

Effects of sliding velocity and normal load on friction and wear characteristics of multi-layered diamond-like carbon (DLC) coating prepared by reactive sputtering

Friction and wear tests were performed to investigate effects of sliding velocity and normal load on tribological characteristics of a multi-layered diamond-like carbon (DLC) coating for machine elements. The DLC coatings which consist of sequentially deposited gradient Cr/CrN, W-doped DLC (a-C:H:W) and DLC (a-C:H) layers were formed on carburized SCM 415 Cr–Mo steel disks using a reactive sputtering system. The tests against AISI 52100 steel balls were performed under various sliding velocities (0.0625, 0.125, 0.25, 0.5, 1 and 2 m/s) and normal loads (6.1, 20.7 and 49.0 N) in ambient air (relative humidity=26±2%, temperature=18±2 °C). Each test was conducted for 20 km sliding distance without lubricating oil. The results show that friction coefficients decrease with the increase in sliding velocity and normal load. Wear rates of both surfaces decrease with the increase in normal load. The increase in sliding velocity leads initially to the increase in wear rates up to the maximum value. Then, they decrease, as the sliding velocity increases above specific value that corresponds to the maximum wear rate. Through surface observation and analysis, it is confirmed that formation of transfer layers and graphitized degree of wear surfaces of DLC coatings mainly affect its tribological characteristics.     

Friction and wear measurements of laser-sintered and coated parts

The aim of this research is the investigation of surface properties, the measurements of friction coefficient and wear rate of laser-sintered and coated parts. The industrial background of this research is to prove applicability of laser-sintered prototype tools for injection moulding of fibre-reinforced polymers, furthermore to increase the wear resistance of unalloyed steel tools by laser coatings. The materials of the test specimens were laser-sintered phosphorous bronze and unalloyed steel. For increase of wear resistance we used hard Co-based and glassy-like Fe-based (FeB) coatings. As counter bodies we used polymers reinforced with short carbon and glass fibres. The laboratory model tests of selective laser-sintered parts were carried out on a pin-on-disk machine. In case of coated parts—with higher wear resistance—we used a cylinder-on-cylinder tribometer. The tribological properties were determined at different load and temperature conditions. The results of the investigation show that the friction coefficient and wear resistance of laser treated surfaces are good. The coefficient of friction of coated specimens is slightly less, but the wear rate is significantly less.     

Friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes

MoS2 metal composite coatings have been successful used in dry turning, but its suitability for dry drilling has not been yet established. Therefore, it is necessary to study the friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes. In the present study, MoS2/Zr composite coatings are deposited on the surface of W6Mo5Cr4V2 high speed steel(HSS). Microstructural and fundamental properties of these coatings are examined. Ball-on-disc sliding wear tests on the coated discs are carried out, and the drilling performance of the coated drills is tested. Test results show that the MoS2/Zr composite coatings exhibit decreases friction coefficient to that of the uncoated HSS in sliding wear tests. Energy dispersive X-ray(EDX) analysis on the wear surface indicates that there is a transfer layer formed on the counterpart ball during sliding wear processes, which contributes to the decreasing of the friction coefficient between the sliding couple. Drilling tests indicate that the MoS2/Zr coated drills show better cutting performance compared to the uncoated HSS drills, coating delamination and abrasive are found to be the main flank and rake wear mode of the coated drills. The proposed research founds the base of the application of MoS2 metal composite coatings on dry drilling.     

打壳锤头等离子堆焊镍基涂层组织和性能

采用等离子堆焊技术在打壳锤头基体Q235钢表面进行堆焊,堆焊材料选用分别含有50%WC、40%WC和30%WC+TiC的复合镍基粉末。借助金相显微镜、扫描电子显微镜、显微硬度仪、摩擦磨损试验仪等仪器对所得各堆焊层的显微组织、化学成分、显微硬度、耐磨性和耐蚀性进行分析。试验结果表明,三种合金堆焊层显微组织均为γ-Ni固溶体和弥散分布的不同形态的硬质化合物相,如WC,(Ti,V)C等。三种合金堆焊层与基体界面处冶金结合良好,堆焊层稀释率低,且与基体Q235钢相比,耐电解腐蚀性显著提高。含有30%WC+TiC的镍基合金堆焊层与含有50%WC和40%WC的镍基合金堆焊层相比,具有更高的耐磨性和抗热腐蚀性。因而含有30%WC+TiC的镍基合金堆焊层综合性能最优,能够大幅度延长打壳锤头使用寿命,具有广泛的应用前景。     

Effect of oil additives on the durability of hydrogenated DLC coating under boundary lubrication conditions

Diamond-like carbon (DLC) coatings have became accepted non-ferrous coatings for automotive tribo-components as they offer excellent tribological properties resulting in improved fuel economy and reduced dependence on existing lubricant additives which can be harmful to catalytic converters and ultimately to the environment. Obtaining optimum durability (wear) as well as high fuel economy (low friction) using DLC-coated parts relies in part on the compatibility between surface and lubricant additives. The objective of this study is to understand the role of friction modifiers and antiwear additives on the durability of DLC coating under boundary lubrication conditions. Experiments were performed using a pin-on-plate tribotester using plates coated by 30 at.% hydrogen containing DLC (HDLC) sliding against cast iron (CI) pins. The physical observation of the wear scar, formed on the HDLC coating by low friction and/or antiwear additives, was performed using both optical and scanning electron microscopes. X-ray photoelectron spectroscopy analysis was performed on the tribofilms to help to understand the tribochemical interactions between oil additives and the HDLC coating. Based on the physical observations and tribochemical analysis of the wear scar, the mechanisms of failure/wear of the HDLC coating are proposed and the requirement for designing optimal additive packages for the HDLC coating is discussed.     

The lubricant-coating interaction in rolling and sliding contacts

The research presented in this paper was aimed at elaboration of a new technology for heavy-loaded machine elements, lubricated with ecological oils.The tribological experiments were performed using four-ball tester (scuffing resistance), cone-three balls pitting tester (fatigue life), as well as gear test rig (resistance of lubricated gears to scuffing). The tribosystems were lubricated with various base oil and vegetable-based eco-oil.The tested components were coated with standard single coatings (TiN, CrN) and low-friction coatings (a-C:H:W, MoS₂/Ti). The results obtained confirm that low-friction a-C:H:W coating has a great potential for application in heavy-loaded machine components. Under extreme-pressure conditions this coating can take over the functions of anti-wear/extreme-pressure (AW/EP) additives and through this it is possible to minimise the application of toxic lubricating additives and achieve “ecological lubrication”.