Magnetic properties of melt spun NdFe10Cr2-Nd0.67B0.33 pseudobinary alloys

The coercivity of the melt-spun pseudobinary (NdFe₁₀Cr ₂)_1-x (Nd₂B)_x alloys, in which Nd₂B represents a composition of Nd_0.67B_0.33, was systematically studied. It was found that significant coercivities are possible with optimal additions of the Nd-B composition at x=0.5-0.7. The as-spun (substrate velocity=10 m/s) coercivity increased from 0.1 kOe at x=0.0 to maxima of 7.0 and 7.5 kOe at x=0.5 and 0.7, due to the Nd₂ Fe₁₄B and a new Fe-Nd phase, respectively, as evidenced from thermomagnetic analysis and X-ray diffraction. Annealing the overquenched amorphous x=0.7 alloy led to the crystallization of the Nd₂Fe₁₄B phase, and a coercivity of 8.5 kOe was obtained     

Magnetic properties of Sm2Fe17Nxpowder and bonded magnet

Sm₂Fe₁₇N_x powders were prepared through metallurgical processes such as melting, casting, pulverizing, and gas nitrogenation. Epoxy resin and zinc-bonded magnets were prepared from the powder by a compression molding process. The magnetic properties of magnetically aligned Sm₂Fe₁₇N_x powder were (BH)_max=170 kJ/m³ (21.4 MG-Oe), Br=1.20 T, and H_cJ=547 kA/m (6.87 kOe). Those of an epoxy-bonded magnet were (BH)_max =103 kJ/m³ (13.0 MG-Oe) and Br=0.835 T. H _cJ values in excess of 2 MA/m (25 kOe) were observed in the case of a zinc-bonded magnet     

Analysis of temperature-dependent magnetization in Sm-Fe-Ccompounds using a two-sublattice model

The temperature dependence of magnetization in Sm₃Fe ₂₀C_x (x =0.3, 0.6, 0.8) and Sm₂Fe_16.5C_1.0 intermetallic compounds with rhombohedral structure has been analyzed using molecular field theory. On the basis of a two-sublattice model, the molecular field coefficients are calculated using a numerical fitting method. The Curie temperature and the Fe-Fe, Sm-Fe, Sm-Sm magnetic interaction energies for the compounds are determined from these coefficients. The results show that the increase of the Curie temperature (T_c) with the increase of carbon content x is attributed mainly to the enhancement of the Fe-Fe exchange interaction energy caused by carbon atoms added     

High coercivity in melt-spun SmFe10(Ti,M)2 ribbons (M=V/Cr/Mn/Mo)

Magnetic properties of SmFe₁₀(Ti,M)₂ melt-spun ribbons were studied, where M is V, Cr, Mn, and Mo. The ribbons (M=V/Cr/Mo) quenched at 20 m/s exhibit the high coercivities of 4.2-5.5 kOe. Annealing the ribbons quenched at 40 m/s enhances their coercivities in the range of 5.9-10.0 kOe. In particular, SmFe₁₀ (TiV) and SmFe₁₀(TiCr) ribbons yield coercivities of 10.0 kOe and 7.9 kOe, respectively. This is the highest value among the reported melt-spun ThMn₁₂-type structure ribbons. The importance of Sm atmosphere during annealing in minimizing the Sm evaporation from ribbons is also demonstrated     

Analytical electron microscopy of Sm(Co,Fe,Cu, Zr)9

Electron microscopic studies of as-cast Sm(Co,Fe,Cu,Zr)₉ magnets revealed a hexagonal phase of the type Sm₂(Co,Fe,Cu,Zr)₁₇ with crystal lattice parameters of a=0.84 nm and c=3.2 nm. After a solid solution treatment, only rhombohedral (3R) and hexagonal (2H) grains were found. After an additional annealing treatment at 800°C, grains with a microcellular precipitation structure similar to the one found in Sm(Co,Fe,Cu,Zr)_7.5 magnets occurred. In addition, in the as-cast and after-aged samples, other, partly unidentified Cu- or (Co,Fe)-enriched phases were detected     

Properties of the W-type hexaferritePbZn2Fe16O27

W-type Pb-hexaferrites were prepared by standard ceramic methods. The lattice constants found by refinement were a=0.59140±0.00006 nm and c=3.29209±0.00041 nm. The X-ray density of a typical composition PbZn_1.9Fe_15.3O_25.8 was ρ=5.32 g/cm³ and the Vickers microhardness value h _v=6 kN/mm². A plot of the saturation magnetization versus temperature is given. The extrapolated value of the saturation magnetization (H→∞, T→0) was σ_s=108 emu×g^-1, and the Curie temperature was T_c=600±20 K     

Magnetic ordering in Zn substitutedCo1.4Ge0.4Fe1.2O4 spinelsystem

A systematic study of the Co_1.4Ge_0.4Fe_1.2O₄ system by X-ray, magnetization, and AC-susceptibility techniques is presented. The present system exhibits para-ferri-cluster spin glass transition for x⩽0.2, while x⩾0.3 it exhibits only a cluster spin glass transition. The AC susceptibility and DC magnetization data support the cluster spin glass ordering in the system. The system exhibits local spin canting behavior     

Effect of stress on the law of approach to saturation magnetizationin carbon steels

In high fields where the magnetization is approaching saturation, the resolved magnetic polarization I can be expressed by a power series of the inverse of external field H as: I=I_s-b/H ²-c/H³ . . ., or alternatively in terms of the reversible permeability μ_rev=1+(2b/H³+3c/H⁴+ . . .)/μ₀ where I_s is the spontaneous magnetic polarization and b, c, are constants. These equations express the law of approach to saturation magnetization. The coefficient b for a cubic crystal has been deduced as b=0.0762/I_s[K+1.5(λ₁₀₀-λ ₁₁₁)σ]², where σ is the applied stress and others are magnetic constants. The values of reversible permeability μ_rev under biasing field H were measured for carbon steels with applied stresses. The results showed that the square root of 2b changed linearly with the applied stress, The values of magnetic constant K andλ₁₀₀ -λ₁₁₁ were calculated, They agreed with the standard values, but were affected by chemical composition and heat treatment of materials, especially in λ₁₀₀-λ₁₁₁     

NiTi substituted hexaferrites for magnetic recording

In order to obtain hexagonal ferrites with improved characteristics for application in the field of the magnetic recording, the ferrimagnetic Sr(NiTi)_x Fe_12-2xO₁₉ system is studied. Preliminary investigations suggested that NI is more effective than Co in reducing the magnetic anisotropy of hexaferrites. The system was analyzed as a function of the degree of substitution x and of the reaction temperature T_R and time τ. The reactivity of the mixtures and their magnetic characteristics (σ, H_c, H_A, T_c) were measured, and from the _χT(H) data it was possible to distinguish between single-domain or polydomain particles. The results are presented. The influence of the extraneous magnetic phases on the coercive field value was also studied and a preliminary investigation of the relation between coercive and anisotropy fields was carried out     

Grain size dependence of coercivity and permeability innanocrystalline ferromagnets

Amorphous ribbons of composition Fe_74.5-xCu_xNb₃Si_13.5B₉ (x=0, 1 at.%) have been annealed between about 500°C and 900°C. This produced a series of crystallized samples with grain sizes between about 10 nm and 300 nm and with coercivities H _c and initial permeabilities μ_i varying over several orders of magnitude. The best soft magnetic properties (H _c≈0.01 A/cm and μ_i≈80×10³ ) were observed for the smallest grain sized of about 10 nm. With increasing grain size D, coercivity steeply increases following a D⁶-power law (up to D≈50 nm). H_c then runs through a maximum of H_c≈30 A/cm and decreases again for grain sizes above 150 nm according to the well-known 1/D law for polycrystalline magnets. The initial permeability was found to vary in a similar manner, essentially being inversely proportional to coercivity. The variation of the soft magnetic properties with the average grain size is discussed and compared with the predictions of the random anisotropy model and other theories for the magnetization reversal     

悬浮区域熔炼法制备Ce1-xPrxB6单晶体及其热发射性能研究

以CeB₆和PrB₆粉末为原料, 采用放电等离子烧结结合悬浮区域熔炼法成功制备了晶体质量良好的多元稀土六硼化物Ce_1-xPr_xB₆(x=0.1、0.2、0.4)单晶体, 并系统研究了该系列单晶体(100)晶面热电子发射性能。结果表明: Ce_0.8Pr_0.2B₆单晶(100)晶面具有最好的热发射性能, 在1873 K, 最大电流发射密度达到66.07 A/cm², 比CeB₆单晶的电流发射密度提高约20%。此外, Ce_0.9Pr_0.1B₆、Ce_0.6Pr_0.4B₆单晶(100)晶面的热发射电流密度分别为65.81 A/cm²和65.31 A/cm²。Ce_0.8Pr_0.2B₆单晶(100)晶面的逸出功最低, 为2.61 eV, 其它单晶(100)晶面的逸出功在2.64~2.753 eV范围内。因此, Ce_1-xPr_xB₆多元稀土六硼化物单晶具有良好的发射性能和低的逸出功, 作为热阴极材料有很好的应用前景。     

Magnetic properties of GdBa2Cu3O7crystals in high magnetic field

The magnetic properties of single crystals of GdBa₂Cu ₃O₇ were investigated in a magnetic field of up to 20 T applied parallel to the c axis in the 1.7-300 K temperature range. In the superconducting state, the field and temperature dependences of the critical current densities were deduced from the hysteresis of the half-cycle using Bean's critical state model. The Gd³⁺ paramagnetic moment was then studied. Above about 20 K, the M(H) isotherms were found to be given, at different temperatures, by the Brillouin function of the free Gd³⁺ ion. Below 20 K, the average magnetization does not obey the Brillouin law. The normal-state susceptibility was described by the free-ion Curie-Weiss law     

STM control of noninteger residual charge Q0 onthe central electrode of a double-tunnel junction

In a voltage-biased mesoscopic double-tunnel junction, the Coulomb threshold V_C is an e-periodic function of Q ₀, the charge on the inner electrode. In the STM work described here, a large Au tip images 100-Å Ag particles deposited on a cleaved BSCCO crystal substrate. Stable double junctions between the tip, the imaged particle, and the substrate are identified by Coulomb staircase I(V)'s. The control of Q ₀ is demonstrated by the variation of tip-particle spacing. The parameterization of such results permits a discussion of Q ₀ variation mechanisms     

Determination of the time-dependence of ΩNBS usingthe quantized Hall resistance

The quantum Hall effect is being used to monitor the US legal representation of the ohm, or as-maintained ohm, Ω_NBS. Measurements have been made on a regular basis since August 1983. Individual transfers between the quantized Hall resistance R _H and the five 1-Ω resistors which comprise Ω_NBS can be made with a total of one standard deviation (1σ) uncertainty of ±0.014 p.p.m. This uncertainty is the root-sum-square of 32 individual components. The time-dependent expression for R_H in terms of Ω_NBS is: R_H=25812.8[1+(1.842±0.012)×10^-6 =(0.0529±0.0040)(t-0.7785)×10^-6 /year] Ω_NBS, where t is measured in years from January 1, 1987. The value of Ω_NBS is, therefore, decreasing at the rate of (0.0529±0.0040) p.p.m./year     

Quantized Hall resistance measurements

The quantized Hall resistances, R_H(4), of Si MOSFETs were measured at ≈0.5 K in a magnetic field of 15 T. The value of R_H(4) was determined in terms of the Commonwealth Scientific and Industrial Research Organization (CSIRO) realization of the SI ohm. A weighted mean of three determinations gave a value for the quantity R_H(4) of (6453.203,36(52)) Ω_SI-NML which can also be expressed as 6453.2(1.000,000,52(8)) Ω_SI-NML. This R_H (4) value gives a value for h/e² which is about 0.3 p.p.m. larger than the value for h/e² derived from the anomalous moment of the electron, using the quantum electrodynamics (QED) theory     

Hot-pressed Mn-Zn-Ni and Mn-Zn-Co ferrites for magnetic recordingheads

Ni²⁺ and Co²⁺ substituted Mn-Zn ferrites have been developed as high-density magnetic recording materials by hot pressing using optimum sintering parameters. Ferrite series of the composition Mn_0.6Zn_0.4-xNi_xFe₂ O₄ and Mn_0.6Zn_0.4-yCo_yFe₂O₄ were prepared by the hot-pressing technique wherein x and y varied from 0.0 to 0.4 in steps of 0.05. It yielded ferrites with improved magnetic properties having higher hardness (⩾650 Vickers units), low porosity (<0.1%), and small grain size (≈10 μm). The initial permeability increased, whereas the coercive field decreased for an Ni²⁺ concentration x or a Co ²⁺ concentration y equal to 0.05. Maximum values of saturation magnetization equal to 4850 and 5250 G were obtained for x and y equal to 0.225 and 0.275, respectively. The Curie temperature increased appreciably, whereas the DC resistivity decreased for a larger substitution of Ni²⁺ and Co²⁺ ions     

The (SmZr)Co$_3$Phase in Sm(CoFeCuZr)$_rm z$Magnets

Detailed microstructural characterization of magnets and homogenized as-cast alloys, which included X-ray diffraction Rietveld analysis, has indicated that the so-called platelet or lamellae phase is (SmZr)₁(CoFeCu)₃ with the PuNi₃ structure and lattice parameters a~0.5 nm and c~2.4 nm. The structural and magnetic properties of the (SmZr)Co₃ phase were investigated. The microstructure shows two phases differing in their Zr/Sm ratio. Magnetization curves for the samples (Sm_0.33Zr _0.67)Co₃, (Sm_0.33Zr_0.67)Co _2.97Fe_0.03, and (Sm_0.67Zr_0.33)Co₃ are consistent with the two-phase microstructure observed. Room temperature coercivity values of these samples are low (ap1 kOe.)     

Corrosion study in TbFeCoCr amorphous magneto-optical films

(Tb₂₀Fe₆₅Co₁₅)₉₄Cr ₆ film shows high corrosion resistance with good magnetooptical properties, H_c=4.9 kOe, &thetas;_k=0.3°, K_u=1.4×10⁶ erg/cm³ and T_c=230°C. Pit corrosion in 1N-NaCl aqueous solution and wet corrosion in 85°C and 85%RH atmosphere were studied for TbFeCo films with and without Cr addition. It is suggested that pit corrosion occurs by a chemical reaction between the anodic pit wall and the cathodic film surface, resulting in a piling up of corroded products inside the pits. On the other hand, wet corrosion in TbFeCo and TbFeCoCr films shows a bubble-chain-like morphology similar to conventional filiform corrosion observed in a coated film. This seems to take place by discontinuous movement of the anodic reaction area ahead of the bubbles     

Magnetic properties of melt spunSmFe11Ti-Sm2TM17 pseudobinary alloys

Several alloys in the SmFe₁₁Ti-Sm₂TM₁₇ (TM=Co/Fe/Cu/Zr) pseudobinary system containing O-90 wt.% Sm₂TM₁₇ were prepared by the melt spinning technique. A maximum as-spun coercivity of 4.6 kOe was obtained for the alloy containing 10 wt.% Sm₂TM₁₇ at a substrate velocity of 15 m/s. The coercivity is enhanced to 5.3 kOe after annealing at 800°C for 1 h. XRD (X-ray diffractometry) and TEM (transmission electron microscopy) were used to investigate the microstructure of the alloys. It is suggested that the grain refinement, doping of the 1-12 phase with Sm and other elements, and reduced free iron might be the main causes coercivity enhancement     

Development of high-quality ceramic powders for Sr0.9Ca0.1Zn2-W type hexagonal ferrite for permanentmagnet devices

Fine ceramic powders of Sr_0.9Ca_0.1Zn₂ Fe₁₆O₂₇ (Sr_0.9Ca_0.1Zn ₂-W) ferrite, of almost single domain grain size ~1 μm, have been synthesized successfully by sintering for a few hours a mixture of SrCO₃, CaCO₃, ZnO, and α-Fe₂ O₃ in stoichiometric amounts at an effectively low temperature (T_s) of ~1100°C. Carbon dioxide evolves in the reaction Sr(Ca)CO₃+2ZnO+8 α-Fe₂D₃ &lrarr2;Sr(Ca)Zn₂Fe₁₆O₂+C₂ , making fine pores in the sample, which prevent large grain growth of the material and result in a very loose powder. The small ⩽10% substitution of Sr by Ca activates the reaction, but preserves the crystallization of the small-sized grains. This yields magnetic properties useful for most permanent magnet applications, with a promisingly high coercivity H_c~3650 Oe and saturation magnetization M_s~65 emu/g. A considerably better saturation magnetization M_s~85 emu/g can be obtained by sintering the samples at higher T_s~1300°C, but that results in a rather very low coercivity H_c~105 Oe