A direct-conversion CMOS transceiver for the 802.11a/b/g WLAN standard utilizing a Cartesian feedback transmitter

A fully integrated dual-band transceiver is implemented in 0.18-/spl mu/m CMOS and is compliant with the IEEE 802.11a/b/g standards. The direct-conversion transceiver occupies 12 mm/sup 2/ in a QFN-40 package. A fractional-N synthesizer operates at twice the channel frequency, covering continuously bands from 4.9 to 5.9 GHz, as well as the 2.4-GHz band. The 5- and 2.4-GHz receivers achieve a sensitivity level below -73 dBm in the 54-Mb/s mode and below -93 dBm in the 6-Mb/s mode, while consuming 230 mW. A fast RSSI-channel power-detection system allows to power-down signal processing in the listen mode. The 5- and 2.4-GHz transmitters implement a wideband Cartesian feedback loop for enhanced EVM performances and improved spectrum masks compliance. The transmitters deliver -2-dBm average power with an EVM of 3% in the 54-Mb/s mode while consuming 300 mW.     

A dual-band 5.15-5.35-GHz, 2.4-2.5-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a/b/g wireless LAN

A single-chip dual-band 5.15-5.35-GHz and 2.4-2.5-GHz zero-IF transceiver for IEEE 802.11a/b/g WLAN systems is fabricated on a 0.18-/spl mu/m CMOS technology. It utilizes an innovative architecture including feedback paths that enable digital calibration to help eliminate analog circuit imperfections such as transmit and receive I/Q mismatch. The dual-band receive paths feature a 4.8-dB (3.5-dB) noise figure at 5.25 GHz (2.45 GHz). The corresponding sensitivity at 54 Mb/s operation is -76 dBm for 802.11a and -77 dBm for 802.11g, both referred at the input of the chip. The transmit chain achieves output 1-dB compression at 6 dBm (9 dBm) at 5 GHz (2.4 GHz) operation. Digital calibration helps achieve an error vector magnitude (EVM) of -33 dB (-31 dB) at 5 GHz (2.4 GHz) while transmitting -4 dBm at 54Mb/s. The die size is 19.3 mm/sup 2/ and the power consumption is 260 mW for the receiver and 320 mW (270 mW) for the transmitter at 5 GHz (2.4 GHz) operation.     

A highly integrated dual-band multimode wireless LAN transceiver

A fully integrated radio transceiver chip for the 2.4- and 5-GHz WLAN standards 802.11a/b/g is presented in a 0.25-/spl mu/m 40-GHz BiCMOS technology. The chip integrates the low-noise amplifiers, mixers, channel filters, programmable gain control, synthesizers with voltage-controlled oscillators and reference oscillator, transmitters, antialiasing filters, and voltage regulators. The key performances of the presented transceiver are a receive sensitivity of -85 dBm and -74 dBm for 11-Mb/s complementary code keying (CCK) and 54 Mb/s orthogonal frequency division multiplexing (OFDM) modes, respectively, and an error vector magnitude of -35 dB measured at the transmitter with an output power of -4 dBm at 54-Mb/s 802.11a mode. The transceiver exceeds all IEEE requirements for the 802.11a/b/g CCK and OFDM standards and supports a frequency range of 4.9 to 6 GHz for the future extensions of the 802.11a standard in different countries.     

A low-power 2.4-GHz transmitter/receiver CMOS IC

A 2.4-GHz CMOS receiver/transmitter incorporates circuit stacking and noninvasive baseband filtering to achieve a high sensitivity with low power dissipation. Using a single 1.6-GHz local oscillator, the transceiver employs two upconversion and downconversion stages while providing on-chip image rejection filtering. Realized in a 0.25-/spl mu/m digital CMOS technology, the receiver exhibits a noise figure of 6 dB and consumes 17.5 mW from a 2.5-V supply, and the transmitter delivers an output power of 0 dBm with a power consumption of 16 mW.     

A 5-GHz direct-conversion CMOS transceiver utilizing automatic frequency control for the IEEE 802.11a wireless LAN standard

A fully integrated CMOS direct-conversion 5-GHz transceiver with automatic frequency control is implemented in a 0.18-/spl mu/m digital CMOS process and housed in an LPCC-48 package. This chip, along with a companion baseband chip, provides a complete 802.11a solution The transceiver consumes 150 mW in receive mode and 380 mW in transmit mode while transmitting +15-dBm output power. The receiver achieves a sensitivity of better than -93.7dBm and -73.9dBm for 6 Mb/s and 54 Mb/s, respectively (even using hard-decision decoding). The transceiver achieves a 4-dB receive noise figure and a +23-dBm transmitter saturated output power. The transmitter also achieves a transmit error vector magnitude of -33 dB. The IC occupies a total die area of 11.7 mm/sup 2/ and is packaged in a 48-pin LPCC package. The chip passes better than /spl plusmn/2.5-kV ESD performance. Various integrated self-contained or system-level calibration capabilities allow for high performance and high yield.     

A single-chip dual-band direct-conversion IEEE 802.11a/b/g WLAN transceiver in 0.18-/spl mu/m CMOS

This paper presents a single-chip dual-band CMOS direct-conversion transceiver fully compliant with the IEEE 802.11a/b/g standards. Operating in the frequency ranges of 2.412-2.484 GHz and 4.92-5.805 GHz (including the Japanese band), the fractional-N PLL based frequency synthesizer achieves an integrated (10 kHz-10 MHz) phase noise of 0.54/spl deg//1.1/spl deg/ for 2/5-GHz band. The transmitter error vector magnitude (EVM) is -36/-33 dB with an output power level higher than -3/-5dBm and the receiver sensitivity is -75/-74 dBm for 2/5-GHz band for 64QAM at 54 Mb/s.     

A single-chip CMOS transceiver for 802.11a/b/g wireless LANs

A dual-band trimode radio fully compliant with the IEEE 802.11a, b, and g standards is implemented in a 0.18-/spl mu/m CMOS process and packaged in a 48-pin QFN package. The transceiver achieves a receiver noise figure of 4.9/5.6 dB for the 2.4-GHz/5-GHz bands, respectively, and a transmit error vector magnitude (EVM) of 2.5% for both bands. The transmit output power is digitally controlled, allowing per-packet power control as required by the forthcoming 802.11 h standard. A quadrature accuracy of 0.3/spl deg/ in phase and 0.05 dB in amplitude is achieved through careful analysis and design of the I/Q generation parts of the local oscillator. The local oscillators achieve a total integrated phase noise of better than -34 dBc. Compatibility with multiple baseband chips is ensured by flexible interfaces toward the A/D and D/A converters, as well as a calibration scheme not requiring any baseband support. The chip passes /spl plusmn/2 kV human body model ESD testing on all pins, including the RF pins. The total die area is 12 mm/sup 2/. The power consumption is 207 mW in the receive mode and 247 mW in the transmit mode using a 1.8-V supply.     

A single-chip dual-band tri-mode CMOS transceiver for IEEE 802.11a/b/g wireless LAN

A single-chip dual-band tri-mode CMOS transceiver that implements the RF and analog front-end for an IEEE 802.11a/b/g wireless LAN is described. The chip is implemented in a 0.25-/spl mu/m CMOS technology and occupies a total silicon area of 23 mm/sup 2/. The IC transmits 9 dBm/8 dBm error vector magnitude (EVM)-compliant output power for a 64-QAM OFDM signal. The overall receiver noise figure is 5.5/4.5 dB at 5 GHz/2.4 GHz. The phase noise is -105 dBc/Hz at a 10-kHz offset and the spurs are below -64 dBc when measured at the 5-GHz transmitter output.     

A WiMedia/MBOA-Compliant CMOS RF Transceiver for UWB

A WiMedia/MBOA compliant RF transceiver for ultra-wideband data communication in the 3-5-GHz band is presented. The transceiver includes receiver, transmitter and synthesizer is completely integrated in 0.13-mum standard CMOS technology. The receiver uses a feedback-based low-noise amplifier (LNA) to obtain an RF gain of 4 to 37 dB and an overall measured noise figure of 3.6 to 4.1 dB over the 3-5-GHz band of interest. The transmitter supports an error vector magnitude (EVM) of -28 dB up to -4 dBm output power and meets the FCC and WiMedia mask specifications. The power consumption from a single supply voltage of 1.5 V is 237 mW for the receiver and 284 mW for the transmitter, both including the synthesizer     

A single-chip digitally calibrated 5.15-5.825-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a wireless LAN

The drive for cost reduction has led to the use of CMOS technology in the implementation of highly integrated radios. This paper presents a single-chip 5-GHz fully integrated direct conversion transceiver for IEEE 802.11a WLAN systems, manufactured in 0.18-/spl mu/m CMOS. The IC features an innovative system architecture which takes advantage of the computing resources of the digital companion chip in order to eliminate I/Q mismatch and achieve accurately matched baseband filters. The integrated voltage-controlled oscillator and synthesizer achieve an integrated phase noise of less than 0.8/spl deg/ rms. The receiver has an overall noise figure of 5.2 dB and achieves sensitivity of -75 dBm at 54-Mb/s operation, both referred to the IC input. The transmit error vector magnitude is -33 dB at -5-dBm output power from the integrated power-amplifier driver amplifier. The transceiver occupies an area of 18.5 mm/sup 2/.     

A dual-mode 802.11b/bluetooth radio in 0.35-/spl mu/m CMOS

A fully integrated dual-mode CMOS transceiver tuned to 2.4 GHz consumes 65 mA in receive mode and 78 mA in transmit mode from a 3-V supply. The radio includes all the receive and transmit building blocks, such as frequency synthesizer, voltage-controlled oscillator (VCO), and power amplifier, and is intended for use in 802.11b and Bluetooth applications. The Bluetooth receiver uses a low-IF architecture for higher level of integration and lower power consumption, while the 802.11b receiver is direct conversion. The receiver achieves a typical sensitivity of -88 dBm at 11 Mb/s for 802.11b, and -83 dBm for Bluetooth mode. The receiver minimum IIP3 is -8 dBm. Both transmitters use a direct-conversion architecture, and deliver a nominal output power of 0 dBm, with a power range of 20 dB in 2-dB steps.     

A fully integrated SOC for 802.11b in 0.18-/spl mu/m CMOS

A fully integrated system-on-a-chip (SOC) intended for use in 802.11b applications is built in 0.18-/spl mu/m CMOS. All of the radio building blocks including the power amplifier (PA), the phase-locked loop (PLL) filter, and the antenna switch, as well as the complete baseband physical layer and the medium access control (MAC) sections, have been integrated into a single chip. The radio tuned to 2.4 GHz dissipates 165 mW in the receive mode and 360 mW in the transmit mode from a 1.8-V supply. The receiver achieves a typical noise figure of 6 dB and -88-dBm sensitivity at 11 Mb/s rate. The transmitter delivers a nominal output power of 13 dBm at the antenna. The transmitter 1-dB compression point is 18 dBm and has over 20 dB of gain range.     

A low-power high-performance SiGe BiCMOS 802.11a/b/g transceiver IC for cellular and bluetooth Co-existence applications

This paper describes a high-performance WLAN 802.11a/b/g radio transceiver, optimized for low-power in mobile applications, and for co-existence with cellular and Bluetooth systems in the same terminal. The direct-conversion transceiver architecture is optimized in each mode for low-power operation without compromising the challenging RF performance targets. A key transceiver requirement is a sensitivity of -77 dBm (at the LNA input) in 54 Mb/s OFDM mode while in the presence of a GSM1900 transmitter interferer. The receiver chain achieves an overall noise figure of 2.8/3.2 dB, consuming 168/185 mW at 2.8 V for the 2.4/5GHz bands, respectively. Signal loopback and transmit power detection techniques are used in conjunction with the baseband modem processor to calibrate the transmitter LO leakage and the transceiver I/Q imbalances. Fabricated in a 70 GHz f/sub T/ 0.25-/spl mu/m SiGe BiCMOS technology for system-in-package (SiP) use, the dual-band, tri-mode transceiver occupies only 4.6 mm/sup 2/.     

A World-Band Triple-Mode 802.11a/b/g SOC in 130-nm CMOS

A fully integrated system-on-a-chip (SOC) in 130-nm CMOS technology compliant with world-band 802.11a/b/g is presented. This SOC integrates all blocks including 2.4-GHz/5-GHz RF tranceiver, baseband physical layer (PHY), and the medium access controller (MAC). At 1.8 V, the whole SOC dissipates 144/168 mA in receiving mode and 114/150 mA in transmitting mode for 2.4-GHz/5-GHz-band operations. The measured receiver sensitivity at 2.4 GHz/5 GHz is $-{hbox{77.5}}/-{hbox{74}} hbox{dBm}$ at 54 Mb/s rate, and the transmitter EVM at 54 Mb/s rate is $-{hbox{33}}/-{hbox{30}} {hbox {dB}}$ at an output power of $-{hbox{7}}/-{hbox{8}} hbox{dBm}$. By integrating multiple on-chip LDOs with no off-chip capacitors, this SOC features the capability of being directly supplied by off-chip switching-type DC/DC converter without performance degradation.      

Low-power/low-voltage RF microsystems for wireless sensors networks

This paper presents radio-frequency (RF) microsystems (MSTs) composed by low-power devices for use in wireless sensors networks (WSNs). The RF CMOS transceiver is the main electronic system and its power consumption is a critical issue. Two RF CMOS transceivers with low-power and low-voltage supply were fabricated to operate in the 2.4 and 5.7 GHz ISM bands. The measurements made in the RF CMOS transceiver at 2.4 GHz, which showed a sensitivity of −60 dBm with a power consumption of 6.3 mW from 1.8 V supply. The measurements also showed that the transmitter delivers an output power of 0 dBm with a power consumption of 11.2 mW. The RF CMOS transceiver at 5.7 GHz has a total power consumption of 23 mW. The target application of these RF CMOS transceivers is for MSTs integration and for use as low-power nodes in WSNs to work during large periods of time without human operation, management and maintenance. These RF CMOS transceivers are also suitable for integration in thermoelectric energy scavenging MSTs.     

A 4-91-GHz traveling-wave amplifier in a standard 0.12-/spl mu/m SOI CMOS microprocessor technology

This paper presents five-stage and seven-stage traveling-wave amplifiers (TWA) in a 0.12-/spl mu/m SOI CMOS technology. The five-stage TWA has a 4-91-GHz bandpass frequency with a gain of 5 dB. The seven-stage TWA has a 5-86-GHz bandpass frequency with a gain of 9 dB. The seven-stage TWA has a measured 18-GHz noise figure, output 1-dB compression point, and output third-order intercept point of 5.5 dB, 10 dBm, and 15.5 dBm, respectively. The power consumption is 90 and 130 mW for the five-stage and seven-stage TWA, respectively, at a voltage power supply of 2.6 V. The chips occupy an area of less than 0.82 and 1 mm for the five-stage and seven-stage TWA, respectively.     

A CMOS RF front-end for a multistandard WLAN receiver

This letter describes the design and performance of a dual band tri-mode receiver front-end compliant with the IEEE 802.11a, b, and g standards. The receiver front-end was built in a 0.18-/spl mu/m CMOS process and achieves a noise figure of 4.7 dB/5.1 dB for the 2.4-GHz/5-GHz bands, respectively. The receiver front-end provides a dual gain mode of 5 dB/30 dB with an IIP3 of -1dBm for the low gain mode. The front-end draws 25 mA/27 mA from a 1.8-V supply for the 2.4-GHz/5-GHz bands, respectively.     

A Fully Integrated 2.4-GHz IEEE 802.15.4-Compliant Transceiver for ZigBee™ Applications

A single-chip 2.4-GHz CMOS radio transceiver with integrated baseband processing according to the IEEE 802.15.4 standard is presented. The transceiver consumes 14.7 mA in receive mode and 15.7 mA in transmit mode. The receiver uses a low-IF topology for high sensitivity and low power consumption, and achieves -101 dBm sensitivity for 1% packet error rate. The transmitter topology is based on a PLL direct-modulation scheme. Optimizations of architecture and circuit design level in order to reduce the transceiver power consumption are described. Special attention is paid to the RF front-end design which consumes 2.4mA in receive mode and features bidirectional RF pins. The 5.77 mm² chip is implemented in a standard 0.18-mum CMOS technology. The transmitter delivers +3 dBm into the 100-Omega differential antenna port     

A Fully Integrated Ultra-Low Insertion Loss T/R Switch for 802.11b/g/n Application in 90 nm CMOS Process

A 30 dBm ultra-low insertion loss CMOS transmit-receive switch fully integrated with an 802.11b/g/n transceiver front-end is demonstrated. The switch achieves an insertion loss of 0.4 dB in transmit mode and 0.1 dB in receive mode. The entire receiver chain from antenna to baseband output achieves a measured noise figure of 3.6 dB at 2.4 GHz. The switch has a P_1dB greater than 30 dBm by employing a substrate isolation technique without using deep n-well technology. The switch employs a 1.2 V supply and occupies 0.02 mm² of die area.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。