Experimental study on the characteristic stages of premixed hydrogen-air flame propagation in a horizontal rectangular closed duct

Deep insight into each stage of premixed hydrogen-air flame propagation in a horizontal rectangular closed duct was experimentally realized with pressure records and high-speed schlieren photographs under various equivalence ratios. The motion patterns of the flame skirt and the contact point sweeping along the wall were divided into multi-section with distinct features. Two types of tulip cusp motions were scrutinized and distinguished within different equivalence ratio ranges. The vibrations of the flame tip position and velocity were determined as common features in the whole observed range of equivalence ratios. But the tulip distortion is conditional and substantially originates from the vibration just with more remarkable amplitude. The change of pressure difference between the measure points respectively close to the left and right ends of the duct correlates well with the flame tip velocity oscillation with a 90° phase prior. The experimental results were compared with the theoretical prediction. Best agreements are only achieved in a narrow range of equivalence ratio ∅=0.91∼2.24$\varnothing =0.91\sim 2.24$, which reveals some limitations of the theoretical model by Bychkov et al.     

An experimental study of premixed hydrogen/air flame propagation in a partially open duct

High-speed schlieren cinematography and pressure records are used to investigate the dynamics of premixed hydrogen/air flame propagation and pressure build up in a partially open duct with an opening located in the upper wall near the right end of the duct. This work provides basic understanding of flame behaviors and the effects of opening ratio on the combustion dynamics. The flame behaves differently under different opening conditions. The opening ratio has an important influence on the flame propagation and pressure dynamics. When the opening ratio α ≤ 0.075 a significant distorted tulip flame can be formed after the full formation of a classical tulip flame. The propagation speed of flame leading tip increases with the opening ratio. The coupling of flame front with the pressure wave is strong at low opening ratio. Both the pressure growth rate and oscillation amplitude inside the duct increases as the opening ratio decreases. The formation times of tulip and distorted tulip flames and the corresponding distances of flame front increase with the increase of the opening ratio.     

Experimental study and three-dimensional simulation of premixed hydrogen/air flame propagation in a closed duct

An experimental and numerical study of premixed hydrogen/air flame propagation in a closed duct is presented. High-speed schlieren photography is used in the experiment to record the changes in flame shape and location. The pressure transient during the combustion is measured using a pressure transducer. A dynamic thickened flame model is applied to model the premixed combustion in the numerical simulation. The four stages of the flame dynamics observed in the experiment are well reproduced in the numerical simulation. The oscillations of the flame speed and pressure growth, induced by the pressure wave, indicate that the pressure wave plays an important role in the combustion dynamics. The predicted pressure dynamics in the numerical simulation is also in good agreement with that in the experiment. The close correspondence between the numerical simulation and experiment demonstrate that the TF approach is quite reliable for the study of premixed hydrogen/air flame propagation in the closed duct. It is shown that the flame wrinkling is important for the flame dynamics at the later stages.     

Experimental study of premixed syngas/air flame deflagration in a closed duct

The propagation behaviour of a deflagration premixed syngas/air flame over a wide range of equivalence ratios is investigated experimentally in a closed rectangular duct using a high-speed camera and pressure transducer. The syngas hydrogen volume fraction, φ, ranges from 0.1 to 0.9. The flame propagation parameters such as flame structure, propagation time, velocity and overpressure are obtained from the experiment. The effects of the equivalence ratio and hydrogen fraction on flame propagation behaviour are examined. The results indicate that the hydrogen fraction in a syngas mixture greatly influences the flame propagation behaviour. When φ, the hydrogen fraction, is ≥0.5, the prominently distorted tulip flame can be formed in all equivalence ratios, and the minimum propagation time can be obtained at an equivalence ratio of 2.0. When φ < 0.5, the tulip flame distortion only occurs in a hydrogen fraction of φ = 0.3 with an equivalence ratio of 1.5 and above. The minimum flame propagation time can be acquired at an equivalence ratio of 1.5. The distortion occurs when the maximum flame propagation velocity is larger than 31.27 m s^?1. The observable oscillation and stepped rise in the overpressure trajectory indicate that the pressure wave plays an important role in the syngas/air deflagration. The initial tulip distortion time and the plane flame formation time share the same tendency in all equivalence ratios, and the time interval between them is nearly constant, 4.03 ms. This parameter is important for exploring the quantitative theory or models of distorted tulip flames.     

Experimental and numerical study on premixed hydrogen/air flame propagation in a horizontal rectangular closed duct

Hydrogen is a promising energy in the future, and it is desirable to characterize the combustion behavior of its blends with air. The premixed hydrogen/air flame microstructure and propagation in a horizontal rectangular closed duct were recorded using high-speed video and Schlieren device. Numerical simulation was also performed on Fluent CFD code to compare with the experimental result. A tulip flame is formed during the flame propagating, and then the tulip flame formation mechanism was proposed based on the analysis. The induced reverse flow and vortex motion were observed both in experiment and simulation. The interactions among the flame, reverse flow and vortices in the burned gas change the flame shape and ultimately it develops into a tulip flame. During the formation of the tulip flame, the tulip cusp slows down and stops moving after its slightly forward moving, and then, it starts to move backward and keeps on a longer time, after that, it moves forward again. The structure of the tulip flame is becoming less stable with its length decreasing in flame propagation direction. The flame thickness increases gradually which is due to turbulence combustion.     

Experimental study on the influence of multi-layer wire mesh on dynamics of premixed hydrogen-air flame propagation in a closed duct

Hydrogen, which is considered to be a promising clean energy source, has been studied and applied extensively in industries. In order to improve the safety of hydrogen energy application, an experimental study on the influence of multi-layer wire mesh on dynamics of premixed hydrogen-air flame propagation in a closed duct is conducted. Four different kinds of wire mesh with 40, 45, and 50 layers are chosen in the experiments. High speed schlieren photography is applied to capture the flame shape changes and determine the flame tip speed. Pressure transducer is used to measure the pressure transient. It is found that flame quenches in the cases of adding wire mesh of 60, 80, and 100 mesh with 45 and 50 layers, while for the wire mesh of 40 mesh, 50 layers cannot even quench the flame. Moreover, the multi-layer wire mesh can effectively suppress the flame tip speed, maximum pressure, and sound waves during premixed hydrogen-air flame propagation in the duct. The attenuated maximum pressure reaches approximately 78.6% in the case of adding wire mesh of 100 mesh-50 layers.     

Onset of cellular instabilities in spherically propagating hydrogen-air premixed laminar flames

Using high-speed Schlieren and Shadow photography, the instabilities of outwardly propagating spherical hydrogen-air flames have been studied in a constant volume combustion bomb. Combustion under different equivalence ratios (0.2 ∼ 1.0), temperatures (298 K ∼ 423 K) and pressures (1.0 bar ∼ 10.0 bar) is visualized. The results show that flames experience both unequal diffusion and/or hydrodynamic instabilities at different stages of propagation. The critical flame radius for such instabilities is measured and correlated to the variations of equivalence ratio, temperature and pressure. Analysis revealed that equivalence ratio affects unequal diffusion instability via varying the Lewis number, Le$Le$; increased temperature can delay both types of instabilities in the majority of tests by promoting combustion rate and changing density ratio; pressure variation has minor effect on unequal diffusion instability but is responsible for enhancing hydrodynamic instability, particularly for stoichiometric and near-stoichiometric flames.     

Dynamics of premixed hydrogen-air flame propagation in the duct with pellets bed

Hydrogen, as the promising clean alternative energy in the future, is in the spotlight now all over the world. However, its flammable and explosive hazards should be highly considered during its practical application. In this study, the experiments are performed to study premixed hydrogen-air flame propagation in the duct with pellets bed, especially for fuel-rich condition. High-speed schlieren photography is employed to capture flame front development during the experiments. As well as the pressure transducer, is used to track the pressure buildup in the flame propagation process. Different diameters of pellets and different concentrations of gas mixture are considered in this experimental study. The typical evolutions about the tulip flame are similar in all cases, although the tulip flame formation time caused by the laminar flame speed are different. The flame propagation velocity is pretty enhanced in fuel-lean mixture under the effect of large diameter pellets bed, but it is significantly suppressed in fuel-rich conditions. While for the small diameter pellets (d = 3 mm), the suppression effect on flame propagation and pressure is obtained over a wider range of equivalence ratios, especially a better suppression effect is generated near the stoichiometric condition.     

Experimental study on premixed combustion of spherically propagating methanol-air-nitrogen flames

The outward propagation and development of surface instability of the spark-ignited spherical premixed flames for methanol-air-nitrogen mixtures were experimentally studied by using a constant volume combustion chamber and a high-speed schlieren photography system. The laminar burning velocities, the mass burning fluxes, and the Markstein lengths were obtained at different equivalence ratios, dilution ratios, initial temperatures, and pressures. The laminar burning velocities and the mass burning fluxes give a similar curve versus the equivalence ratios. They increase with the increase of initial temperature and decrease with the increase of dilution ratio. The laminar burning velocity decreases with elevating the initial pressure, while the mass burning flux increases with the increase of the initial pressure. Markstein length decreases slightly with the increase of initial temperature for the rich mixtures. High initial pressure corresponds to low Markstein length. Markstein length increases with the increase of dilution ratio, which is more obvious when the mixture becomes leaner. Equivalence ratio has a slight impact on the development of the diffusive-thermal cellular structure at elevated initial pressures. The initial pressure has a significant influence on the occurrence of the flame front cellular structure. At the elevated pressures, the cracks on the flame surface branch and develop into the cell structure. These cells are bounded by cracks emitting a bright light, which may indicate soot formation. For very lean mixture combustion, the buoyancy effect and cooling effect from the spark electrodes have a significant impact on the flame propagation. The hydrodynamic instability, inhibited with the increase of initial temperature around the stoichiometric equivalence ratio, is enhanced with the increase of initial pressure and suppressed by mixture dilution.     

Effects of position and frequency of obstacles on turbulent premixed propagating flames

This paper studies the effects of the number and location of solid obstacles on the rate of propagation of turbulent premixed flames. A vented explosion chamber is constructed where controlled premixed flames are ignited from rest to propagate past grids or baffles plates as well as other solid obstacles strategically positioned in the chamber. Laser Induced Fluorescence (LIF) is used to image OH which is used as an indicator of the reaction zone while pressure transducers are used to obtain pressure-time traces. Single grids or baffle plates located at different distances from the ignition source are tested. Two as well as three baffle plates are also investigated in varying configurations. It is found that while the peak overpressure increases with increasing number of grids or baffle plates, a limit is reached where the pressure starts to decrease. The location of the obstacles is found to have a significant effect on the overpressure and the flame structure. Higher overpressures are obtained when the baffle plates and obstacles are stacked closer together hence not allowing turbulence to decay. LIF images for OH show that the reaction zones become more contorted with increasing number of baffle plates in the flame path.     

Geometric influence of perforated plate on premixed hydrogen-air flame propagation

Geometrical influence of the perforated plate on flame propagation in hydrogen-air mixtures with various equivalence ratios and initial pressures was experimentally investigated in a channel with the length of 1 m and the cross-section of 7 cm × 7 cm. The perforated plate has the same cross section and three thicknesses of 40 mm, 80 mm and 120 mm. High-speed schlieren photography was employed to capture the flame shape evolution and derive the flame tip velocity. High-speed piezoelectric pressure transducers were flush-mounted upstream and downstream of the perforated plate to measure the pressure transient. It was found that, with the perforated plate in the path of flame, flame undergoes either “go”, or “quench” propagation mode. The limit between these two was dependent on the geometrical size of the perforated plate and the initial conditions of mixtures. Both velocity and pressure were effectively attenuated with the increase in the perforated plate length. Moreover, for “go” propagation mode, the flame process through the perforated plate was characterized by three obvious stages: laminar flame stage, jet flame stage and turbulent flame stage. Whereas, only laminar flame stage was observed in the “quench” mode.     

Large eddy simulation of premixed hydrogen/methane/air flame propagation in a closed duct

In this paper, large eddy simulation (LES) is performed to investigate the propagation characteristics of premixed hydrogen/methane/air flames in a closed duct. In LES, three stoichiometric hydrogen/methane/air mixtures with hydrogen fractions (volume fractions) of 0, 50% and 100% are used. The numerical results have been verified by comparison with experimental data. All stages of flame propagation that occurred in the experiment are reproduced qualitatively in LES. For fuel/air mixtures with hydrogen fractions of 0 and 50%, only four stages of “tulip” flame formation are observed, but when the hydrogen fraction is 100%, the distorted “tulip” flame appears after flame front inversion. In the acceleration stage, the LES and experimental flame speed and pressure dynamic coincide with each other, except for a hydrogen fraction of 0. After “tulip” flame formation, all LES and experimental flame propagation speeds and pressure dynamics exhibit the same trends for hydrogen fractions of 0 and 100%. However, when the hydrogen fraction is 50%, a slight periodic oscillation appears only in the experiment. In general, the different structures displayed in the flame front during flame propagation can be attributed to the interaction between the flame front, the vortex and the reverse flow formed in the unburned and burned zones.     

Experimental study on the explosion behaviors of premixed syngas-air mixtures in ducts

Explosion characteristics of premixed syngas-air mixtures at room temperature and atmospheric pressure were experimentally reported when the explosion flame propagates in ducts with various heights (H) and lengths (L). The discussion was based on flame morphology and pressure dynamics. The ratio of L/H and the ratio of H₂/CO had a significant effect on the explosion flame behaviors as the explosion occurred in ducts. The structure of the explosion flame changes more drastically, as both the L/H ratio is large. The ratio of L/H affected the flame tip dynamics after the flame reached the duct wall, and the time of flame reaching the duct walls is divinable. For a given duct height, the shorter the duct length is, the faster flame propagates, and the maximum flame tip speed was higher as the duct length was small. For a given duct length, flame tip dynamics showed a nearly same development tendency, but the shorter the duct height, the faster the flame propagated. The venting pressure affected the overpressure dynamics, and the venting pressure increased with the increase of the L/H ratio and the H₂/CO. For a given duct height, the overpressure reached the maximum value almost at the same time, and the longer duct length resulted in the greater maximum overpressure. Finally, for a given duct length, the higher duct height caused the higher maximum overpressure.     

Experimental investigation of spherical-flame acceleration in lean hydrogen-air mixtures

Large-scale experiments examining spherical-flame acceleration in lean hydrogen-air mixtures were performed in a 64 m³ constant-pressure enclosure. Equivalence ratios ranging from 0.33 to 0.57 were examined using detailed front tracking for flame diameters up to 1.2 m through the use of a Background Oriented Schlieren (BOS) technique. From these measurements, the critical radii for onset of instability for these mixtures, on the order of 2–3 cm, were obtained. In addition, the laminar burning velocity and rate of flame acceleration as a function of radius were also measured.     

Effects of dimethyl methylphosphonate on premixed methane flames

The impact of dimethyl methylphosphonate (DMMP) was studied in a premixed methane/oxygen/N₂-Ar flame in a flat flame burner slightly under atmospheric pressure at two different equivalence ratios: rich and slightly lean. CH₄, CO, CO₂, CH₂O, CH₃OH, C₂H₆, C₂H₄, and C₂H₂ profiles were obtained with a Fourier Transform Infrared (FTIR) spectrometer. Gas samples, analyzed in the FTIR, were extracted from the reaction zone using a quartz microprobe with choked flow at its orifice. Temperature profiles were obtained by measuring the probe flow rate through the choked orifice. Flame calculations were performed with two existing detailed chemical kinetic mechanisms for organophosphorus combustion. DMMP addition caused all profiles except that of CH₃OH to move further away from the burner surface, which can be interpreted as a consequence of a reduction in the adiabatic flame speed. Experimentally, the magnitude of the shift was 50% greater for the near-stoichiometric flame than for the rich flame. Experimental CH₃OH profiles were four to seven times higher in the doped flames than in the undoped ones. The magnitude of this effect is not predicted in the calculations, suggesting a need for further mechanism development. Otherwise, the two mechanisms are reasonably successful in predicting the effects of DMMP on the flame.     

Experimental study on the premixed syngas-air explosion in duct with both ends open

Premixed flame of stoichiometric syngas-air mixture with various hydrogen volume fractions, 10% ≤ X (H₂) ≤ 90%, propagating in a duct with both ends open is experimentally investigated in this study. Two representative ignition locations, i.e., Ig-1, locating at the center of the duct, and Ig-2, locating at the right open end, are considered. Results show that the tulip flame is first attained in the duct with both ends open at 10% ≤ X (H₂) ≤ 50% as the flame is ignited at Ig-1. However, the flame maintains the convex shape with the cellular structure on the flame surface as the flame is ignited at Ig-2. The cellular structure results from Darrieus-Landau instability, but the Darrieus-Landau instability cannot invert the convex flame front. The flame tip and pressure dynamics have been examined. When the flame is ignited at Ig-1, the flame oscillates violently, and the overpressure profiles oscillate as a Helmholtz-type. When the flame is ignited at Ig-2, the left flame front propagates in an atmospheric pressure with a nearly constant speed. The prominent flame acceleration and oscillation are not observed at Ig-2 because of lacking flame acoustic interaction. What's more, the characteristic time of flame propagation has been compared. The time t_w is shorter while the time t_p is longer than the calculated value, and the time t_e has been delayed by both open ends. The flame propagation process is moderated as the flame propagates in the duct with both ends open.     

Experimental and numerical studies on the premixed syngas swirl flames in a model combustor

Experimental and numerical investigations were performed to study the combustion characteristics of synthesis gas (syngas) under premixed swirling flame mode. Four different type of syngases, ranging from low to high H₂ content were tested and simulated. The global flame structures and post emission results were obtained from experimental work, providing the basis of validation for simulations using flamelet generated manifold (FGM) modelling approach via a commercial computational fluid dynamic software. The FGM method was shown to provide reasonable agreement with experimental result, in particular the post-exhaust emissions and global flame shapes. Subsequently, the FGM method was adopted to model the flame structure and predict the radical species in the reaction zones. Simulation result shows that H₂-enriched syngas has lower peak flame temperature with lesser NO species formed in the reaction zone.     

A DNS study of hydrogen/air swirling premixed flames with different equivalence ratios

Hydrogen/air swirling premixed flames with different equivalence ratios are studied using direct numerical simulation. A fourth-order explicit Runge–Kutta method for time integration and an eighth-order central differencing scheme for spatial discretization are used to solve the full Navier–Stokes (N–S) equation system. A 9 species 19-step reduced mechanism for hydrogen/air combustion is adopted. The flames are stabilized with the help of a recirculation zone characterizing a high swirling flow. The vortex structures of the swirling premixed flames are presented. The flame structures are investigated in terms of the flame front curvature and tangential strain rate probability density functions (pdfs). The local flamelet temperature profiles are also extracted randomly along the flame front and compared with the corresponding laminar flame temperature profile. In order to study preferential diffusion effects, direct numerical simulation of two additional freely propagating planar flames in isotropic turbulence is conducted. Preferential diffusion effects observed in the planar flames are suppressed in the swirling flames. Further analysis confirms that the coherent small-scale eddies play important roles in the interactions between turbulence and the flame front. They are able to change the dynamic properties of the flame font and lead to enhanced burning intensity in the flame front with negative curvature for both stoichiometric and fuel-lean flames.     

Experimental study on explosion characteristics of syngas with different ignition positions and hydrogen fraction

The influence of different ignition positions and hydrogen volume fractions on the explosion characteristics of syngas is studied in a rectangular half-open tube. Three ignition positions were set at the axis of the tube, which are 0 mm, 600 mm and 1100 mm away from the closed end, respectively. A range of hydrogen volume fraction (φ) from 10% to 90% were concerned. Experimental results show that different ignition positions and hydrogen volume fraction have important influence on flame propagation structure. When ignited at 600 mm from the closed end on the tube axis, distorted tulip flame forms when flame propagates to the closed end. The formations of the tulip flame and the distorted tulip flame are accompanied by a change in the direction of the flame front propagation. The flame propagation structure and pressure are largely affected by the ignition position and the hydrogen volume fraction. At the same ignition position, flame propagation speed increases with the growing of hydrogen volume fraction. And the pressure oscillates more severe as the ignition location is closer to the open end. And pressure oscillations bring two different forms. The first form is that the pressure has a periodic oscillation. The amplitude of the pressure oscillation gradually increases. It takes several cycles from the start of the oscillation to the peak. For the second form, the pressure reaches the peak of the oscillation in the first cycle of the start to the oscillation.     

Experimental study on cellular instabilities in hydrocarbon/hydrogen/carbon monoxide–air premixed flames

To investigate cell formation in methane (or propane)/hydrogen/carbon monoxide-air premixed flames, the outward propagation and development of surface cellular instabilities of centrally ignited spherical premixed flames were experimentally studied in a constant pressure combustion chamber at room temperature and elevated pressures. Additionally, unstretched laminar burning velocities and Markstein lengths of the mixtures were obtained by analyzing high-speed schlieren images. In this study, hydrodynamic and diffusional-thermal instabilities were evaluated to examine their effects on flame instabilities. The experimentally-measured unstretched laminar burning velocities were compared to numerical predictions using the PREMIX code with a H₂/CO/C₁-C₄ mechanism, USC Mech II, from Wang et al. [22]. The results indicate a significant increase in the unstretched laminar burning velocities with hydrogen enrichment and a decrease with the addition of hydrocarbons, whereas the opposite effects for Markstein lengths were observed. Furthermore, effective Lewis numbers of premixed flames with methane addition decreased for all of the cases; meanwhile, effective Lewis numbers with propane addition increase for lean and stoichiometric conditions and increase for rich and stoichiometric cases for hydrogen-enriched flames. With the addition of propane, the propensity for cell formation significantly diminishes, whereas cellular instabilities for hydrogen-enriched flames are promoted. However, similar behavior of cellularity was obtained with the addition of methane, which indicates that methane is not a candidate for suppressing cell formation in methane/hydrogen/carbon monoxide-air premixed flames.