稀燃及废气再循环提高增压汽油机热效率的对比研究

在一台直列4缸增压直喷汽油机上针对万有特性最低油耗工况点,进行了稀薄燃烧与废气再循环(exhaust gas recirculation,EGR)提高发动机热效率的对比试验研究。试验结果表明:稀薄燃烧及EGR均能有效降低发动机燃油消耗率,稀释率分别为33%和19%时,采用稀燃和EGR时的最高有效热效率绝对值分别增加2.8%和1.7%,其中稀燃的有效热效率达到了39.9%,稀燃实现更高热效率主要归因于较低的传热损失和未燃损失。从燃烧角度来看,稀燃及EGR稀释都延长了燃烧滞燃期及持续期,但同样稀释率下稀燃的滞燃期更短,稀燃更高的稀释极限实现了更低的传热损失;但EGR抑制爆震,提前燃烧相位,使采用EGR时的排气能量损失低于稀燃。从排放角度来看,稀燃及EGR在高稀释率下均显著降低NO_x排放,而受益于高氧气浓度,相同稀释率下稀燃的HC及CO排放均低于采用EGR时,从而使稀燃的未燃损失更低。     

LP-EGR对增程器GDI汽油机燃烧和排放的影响

为进一步降低燃油消耗率和有害排放,开发增程器专用发动机,在一台缸内直喷(GDI)汽油机上选取增程器的3个运行工况点,开展了当量比燃烧模式下的低压废气再循环(LP-EGR)试验研究.结果表明:随着废气再循环(EGR)率的增加、点火时刻的推迟,缸内压力和放热率峰值降低且推迟,燃烧持续期延长,缸内燃烧由爆震逐渐过渡到失火,NOx排放降低.随着EGR率的增加,HC排放升高,CO和PM排放降低.点火时刻对HC、CO和颗粒物(PM)排放的影响规律随EGR率的变化而不同.引入EGR前、后的颗粒物总数量(PN)浓度值均在较低的数量级(105/cm^3).3个工况点综合优化后的最低有效燃油消耗率为219.1 g/(kW·h),较原机降低了7.75%.     

A comparative study on effects of homogeneous or stratified hydrogen on combustion and emissions of a gasoline/hydrogen SI engine

A comparative study on effects of homogeneous or stratified hydrogen on combustion and emissions was presented for a gasoline/hydrogen SI engine. Three kinds of injection modes (gasoline, gasoline plus homogeneous hydrogen and gasoline plus stratified hydrogen) and five excess air ratios were applied at low speed and low load on a dual fuel SI engine with hydrogen direct injection (HDI) and gasoline port injection. The results showed that, with the increase of excess air ratio, the brake thermal efficiency increases firstly then decreases and reaches the highest when the excess air ratio is 1.1. In comparison with pure gasoline, hydrogen addition can make the ignition stable and speed up combustion rate to improve the brake thermal efficiency especially under lean burn condition. Furthermore, it can reduce the CO and HC emissions because of more complete combustion, but produce more NO_X emissions due to the higher combustion temperature. Since, in the gasoline plus stratified hydrogen mode, the hydrogen concentration near the sparking plug is denser than that of homogeneous hydrogen, the ignition is more stable and faster, which further speed up the combustion rate and improve the brake thermal efficiency. In the gasoline plus stratified hydrogen mode, the brake thermal efficiency increases by 0.55%, the flame development duration decreases by 1.0°CA, rapid combustion duration decreases by 1.3°CA and the coefficient of variation (COV) decreases by 9.8% on average than that of homogeneous hydrogen. However, in the gasoline plus stratified hydrogen mode, due to the denser hydrogen concentration near the sparking plug and leaner hydrogen concentration near the wall, the combustion temperature and the wall quenching distance increase, which make the NO_X and HC emissions increase by 14.3% and 12.8% on average than that of homogeneous hydrogen.     

Realizing the part load control of a hydrogen-blended gasoline engine at the wide open throttle condition

This paper proposed a way for realizing the load control of a hydrogen-blended gasoline engine running at the wide open throttle (WOT) condition through lean combustion. The engine performance of the original gasoline engine and a 3% hydrogen-blended gasoline engine running at the WOT and lean conditions under various loads at a constant engine speed of 1400 rpm was compared. The experimental results showed that because of the reduced residual gas fraction and throttling loss, brake thermal efficiency of the 3% hydrogen-blended gasoline engine running at the WOT and lean conditions was obviously higher than that of the pure gasoline engine. The 3% hydrogen-blended gasoline engine running at the WOT and lean conditions produced much lower particulate and CO emissions than the original gasoline engine. Besides, NOx emissions at part load conditions were also reduced for the 3% hydrogen-blended gasoline engine running at the WOT and lean conditions.     

Experimental study on combustion and emissions performance of a hybrid hydrogen–gasoline engine at lean burn limits

Lean combustion is an effective way for improving the spark-ignited (SI) engine performance. Unfortunately, due to the narrow flammability of gasoline, the pure gasoline-fueled engines sometimes suffer partial burning or misfire at very lean conditions. Hydrogen has many excellent combustion properties that can be used to extend the gasoline engine lean burn limit and improve the gasoline engine performance at lean conditions. In this paper, a 1.6 L port fuel injection gasoline engine was modified to be a hybrid hydrogen–gasoline engine (HHGE) fueled with the hydrogen–gasoline mixture by mounting an electronically controlled hydrogen injection system on the intake manifolds while keeping the original gasoline injection system unchanged. A self-developed hybrid electronic control unit (HECU) was used to flexibly adjust injection timings and durations of gasoline and hydrogen. Engine tests were conducted at 1400 rpm and a manifolds absolute pressure (MAP) of 61.5 kPa to investigate the performance of an HHGE at lean burn limits. Three hydrogen volume fractions in the total intake gas of 1%, 3% and 4.5% were adopted. For a specified hydrogen volume fraction, the gasoline flow rate was gradually reduced until the engine reached the lean burn limit at which the coefficient of variation in indicated mean effective pressure (COVimep) was 10%. The test results showed that COVimep at the same excess air ratio was obviously reduced with the increase of hydrogen enrichment level. The excess air ratio at the lean burn limit was extended from 1.45 of the original engine to 2.55 of the 4.5% HHGE. The engine brake thermal efficiency, CO, HC and NO_x emissions at lean burn limits were also improved for the HHGE.     

稀燃条件下甲醇汽油发动机燃烧和排放特性的试验研究

在一台汽油缸内直喷(GDI)增压发动机上,研究了稀燃条件下燃用不同甲醇汽油混合燃料的燃烧特性和排放特性。试验结果表明:稀燃条件下,随混合气浓度逐渐变稀,当量燃油消耗率呈现出先降低后升高的趋势,并且随着甲醇比例的增加,当量燃油消耗率增加,但均低于原机。在混合气逐渐变稀的过程中,燃烧时缸压峰值和燃烧温度总的变化趋势是逐渐降低,而燃烧持续期和循环变动率逐渐升高。稀燃条件下,CO排放量逐渐降低,碳氢化合物排放呈先降低后增加的趋势。NO_x排放量总的变化趋势是先增大后逐渐降低,随着甲醇体积分数的增加,NO_x的排放量逐渐降低,且3种甲醇、汽油混合燃料的NO_x和CO排放量都低于汽油燃料。     

Investigation of hydrogen addition to methanol-gasoline blends in an SI engine

In this study, effects of hydrogen-addition on the performance and emission characteristics of Methanol-Gasoline blends in a spark ignition (SI) engine were investigated. Experiments were conducted with a four-cylinder and four stroke spark ignition engine. Performance tests were performed via measuring brake thermal efficiency, brake specific fuel consumption, cylinder pressure and exhaust emissions (CO, CO₂, HC, NOx). These performance metrics were analyzed under three engine load conditions (no load, 50% and 100%) with a constant speed of 2000 rpm. Methanol was added to the gasoline up to 15% by volume (5%, 10% and 15%). Besides, hydrogen was added to methanol-gasoline mixtures up to 15% by volume (3%, 6%, 9% and 15%). Results of this study showed that methanol addition increases BSFC by 26% and decreases thermal efficiency by 10.5% compared to the gasoline. By adding hydrogen to the methanol - gasoline mixtures, the BSFC decreased by 4% and the thermal efficiency increased by 2% compared to the gasoline. Hydrogen addition to methanol – gasoline mixtures reduces exhaust emissions by about 16%, 75% and 15% of the mean average values of HC, CO and CO2 emissions, respectively. Lastly, ?t was concluded that hydrogen addition improves combustion process; CO and HC emissions reduce as a result of the leaning effect caused by the methanol addition; and CO2 and NOx emission increases because of the improved combustion.     

Preparation,characterization, engine combustion and emission characteristics of rapeseed oil based hybrid fuels

In this study, hybrid fuels consisting of rapeseed oil/diesel blend, 1% aqueous ethanol and a surfactant (oleic acid/1-butanol mixture) were prepared and tested as a fuel in a direct injection (DI) diesel engine. The main fuel properties such as the density, viscosity and lower heating value (LHV) of these fuels were measured, and the engine performance, combustion and exhaust emissions were investigated and compared with that of diesel fuel. The experimental results showed that the viscosity and density of the hybrid fuels were decreased and close to that of diesel fuel with the increase of ethanol volume fraction up to 30%. The start of combustion was later than that of diesel fuel and the peak cylinder pressure, peak pressure rise rate and peak heat release rate were higher than those of diesel fuel. The brake specific fuel consumption (BSFC) of hybrid fuels was increased with the volume fraction of ethanol and higher than that of diesel. The brake specific energy consumption (BSEC) was almost identical for all test fuels. The smoke emissions were lower than those for diesel fuel at high engine loads, the NO_x emissions were almost similar to those of diesel fuel, but CO and HC emissions were higher, especially at low engine loads.     

双点火及补气对摩托车发动机性能影响的研究

针对摩托车发动机经济性差、排放高的问题,笔者在一台加装了双火花塞和进气补气系统的单缸摩托车发动机上,在不同转速条件下,就双火花塞点火和补气对内燃机燃烧与排放特性的影响进行了试验研究。试验结果表明,采用双点火配合进气补气的方法可以有效降低发动机CO、HC排放及比燃油消耗率。在转速为3500r.min-1的条件下,采用双点火配合进气补气的发动机比燃油消耗率较原机降低约12.5%。在发动机转速高于3000r.min-1时,采用双点火也可以在一定程度上改善发动机经济性并降低CO和HC排放。但NOx排放在双点火条件下较原机略有升高。     

TJ376QE二气门发动机稀薄燃烧的实验研究

汽油机燃烧稀混合气是降低有害尾气排放、燃油消耗率的有效途径。由于二气门发动机改变缸内气体流动比较困难,难以形成空气燃料浓度分布,因此目前国际上成功的稀燃发动机均为四气门结构。为增强其涡流和滚流运动,对二气门的TJ37GQE汽油机进气系统进行了改造,随后强烈的空气运动结果表明其有利于组织空气和燃料在缸内的浓度分布,从而为在二气门汽油机上实现稀薄燃烧打下基础;通过采用二次燃油喷射技术,在缸内形成准均质分层混合气,成功地在二气门汽油机上实现了稀薄燃烧。     

Combustion and emissions characteristics of a hybrid hydrogen–gasoline engine under various loads and lean conditions

The addition of hydrogen is an effective way for improving the gasoline engine performance at lean conditions. In this paper, an experiment aiming at studying the effect of hydrogen addition on combustion and emissions characteristics of a spark-ignited (SI) gasoline engine under various loads and lean conditions was carried out. An electronically controlled hydrogen port-injection system was added to the original engine while keeping the gasoline injection system unchanged. A hybrid electronic control unit was developed and applied to govern the spark timings, injection timings and durations of hydrogen and gasoline. The test was performed at a constant engine speed of 1400 rpm, which could represent the engine speed in the typical city-driving conditions with a heavy traffic. Two hydrogen volume fractions in the total intake of 0% and 3% were achieved through adjusting the hydrogen injection duration according to the air flow rate. At a specified hydrogen addition level, gasoline flow rate was decreased to ensure that the excess air ratios were kept at 1.2 and 1.4, respectively. For a given hydrogen blending fraction and excess air ratio, the engine load, which was represented by the intake manifolds absolute pressure (MAP), was increased by increasing the opening of the throttle valve. The spark timing for maximum brake torque (MBT) was adopted for all tests. The experimental results demonstrated that the engine brake mean effective pressure (Bmep) was increased after hydrogen addition only at low load conditions. However, at high engine loads, the hybrid hydrogen–gasoline engine (HHGE) produced smaller Bmep than the original engine. The engine brake thermal efficiency was distinctly raised with the increase of MAP for both the original engine and the HHGE. The coefficient of variation in indicated mean effective pressure (COVimep) for the HHGE was reduced with the increase of engine load. The addition of hydrogen was effective on improving gasoline engine operating instability at low load and lean conditions. HC and CO emissions were decreased and NOx emissions were increased with the increase of engine load. The influence of engine load on CO₂ emission was insignificant. All in all, the effect of hydrogen addition on improving engine combustion and emissions performance was more pronounced at low loads than at high loads.     

Study on combustion and emission characteristics of a n-butanol engine with hydrogen direct injection under lean burn conditions

The n-butanol fuel, as a renewable and clean biofuel, could ease the energy crisis and decrease the harmful emissions. As another clean and renewable energy, hydrogen properly offset the high HC emissions and the insufficient of dynamic property of pure n-butanol fuel in SI engines, because of the high diffusion coefficient, high adiabatic flame velocity and low heat value. Hydrogen direct injection not only avoids backfire and lower intake efficiency but also promotes to form in-cylinder stratified mixture, which is helpful to enhance combustion and reduce emissions. This experimental study focused on the combustion and emissions characteristics of a hydrogen direct injection stratified n-butanol engine. Three different hydrogen addition fractions (0%, 2.5%, 5%) were used under five different spark timing (10° ,15° ,20° ,25° ,30° CA BTDC). Engine speed and excess air ratio stabled at 1500 rpm and 1.2 respectively. The direct injection timing of the hydrogen was optimized to form a beter stratified mixture. The obtained results demonstrated that brake power and brake thermal efficiency are increased by addition hydrogen directly injected. The BSFC is decreased with the addition of hydrogen. The peak cylinder pressure and the instantaneous heat release rate raises with the increase of the hydrogen addition fraction. In addition, the HC and CO emissions drop while the NOx emissions sharply rise with the addition of hydrogen. As a whole, with hydrogen direct injection, the power and fuel economy performance of n-butanol engine are markedly improved, harmful emissions are partly decreased.     

Performance,combustion and exhaust emissions characteristics investigation using Citrullus colocynthis L. biodiesel in DI diesel engine

The aims of this study is to investigate the performance, combustion and exhaust emissions of a single-cylinder, air cooled, direct injection (DI), compression ignition engine using biodiesel from non-edible feedstock. In this work, biodiesel (B100) used to lead this investigation is Citrullus colocynthis L. methyl ester (CCME) and its blends B30 with diesel fuel. The biodiesel is produced via alkaline-catalyzed transesterification process using methanol (6:1 M ratio), 1% of sodium hydroxide at the reaction temperature of 60 °C for 1 h. The important physical and chemical properties of CCME are close to those of diesel fuel. Fuels (diesel fuel, B100 and B30) were tested on a DI diesel engine at 1500 rpm for various power outputs. The results indicated that B100 and B30 exhibit the same combustion characteristics compared to diesel fuel. However, B100 and B30 display earlier start of combustion. At lower engine loads, the peaks of cylinder pressure and heat release rate (HRR) were higher for B30 than B100 and diesel fuel during premixed combustion period. At higher engine loads the peaks of cylinder pressure was higher for B100 than B30 and diesel fuel, but the HRR during diffusion combustion is more considerable than diesel fuel. The brake specific fuel consumption (BSFC) was higher for B100 than diesel fuel at all engine loads while B30 exhibited comparable trends. The thermal efficiency is slightly higher for B100 than B30 and diesel fuel at low loads and increase for B30 at full loads.B30 and B100 provided a higher reduction of hydrocarbons emissions up to 50% for B100. Nitrogen oxides and particulate matter emissions were also reduced.     

Comparative engine performance and emission analysis of CNG and gasoline in a retrofitted car engine

A comparative analysis is being performed of the engine performance and exhaust emission on a gasoline and compressed natural gas (CNG) fueled retrofitted spark ignition car engine. A new 1.6 L, 4-cylinder petrol engine was converted to the computer incorporated bi-fuel system which operated with either gasoline or CNG using an electronically controlled solenoid actuated valve mechanism. The engine brake power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature and exhaust emissions (unburnt hydrocarbon, carbon mono-oxide, oxygen and carbon dioxides) were measured over a range of speed variations at 50% and 80% throttle positions through a computer based data acquisition and control system. Comparative analysis of the experimental results showed 19.25% and 10.86% reduction in brake power and 15.96% and 14.68% reduction in brake specific fuel consumption (BSFC) at 50% and 80% throttle positions respectively while the engine was fueled with CNG compared to that with the gasoline. Whereas, the retrofitted engine produced 1.6% higher brake thermal efficiency and 24.21% higher exhaust gas temperature at 80% throttle had produced an average of 40.84% higher NO_x emission over the speed range of 1500–5500 rpm at 80% throttle. Other emission contents (unburnt HC, CO, O₂ and CO₂) were significantly lower than those of the gasoline emissions.     

Improving the performance of a gasoline engine with the addition of hydrogen-oxygen mixtures

The limited fossil fuel reserves and severe environmental pollution have pushed studies on improving the engine performance. This paper investigated the effect of hydrogen-oxygen blends (hydroxygen) addition on the performance of a spark-ignited (SI) gasoline engine. The test was performed on a modified SI engine equipped with a hydrogen and oxygen injection system. A hybrid electronic control unit was adopted to govern the opening and closing of hydrogen, oxygen and gasoline injectors. The standard hydroxygen with a fixed hydrogen-to-oxygen mole fraction of 2:1 was applied in the experiments. Three standard hydroxygen volume fractions in the total intake gas of 0%, 2% and 4% were adopted. For a given hydroxygen blending level, the gasoline injection duration was adjusted to enable the excess air ratio of the fuel-air mixtures to increase from 1.00 to the engine lean burn limit. Besides, to compare the effects of hydroxygen and hydrogen additions on the performance of a gasoline engine, a hydrogen-enriched gasoline engine was also run at the same testing conditions. The test results showed that the hydroxygen-blended gasoline engine produced higher thermal efficiency and brake mean effective pressure than both of the original and hydrogen-blended gasoline engines at lean conditions. The engine cyclic variation was eased and the engine lean burn limit was extended after the standard hydroxygen addition. The standard hydroxygen enrichment contributed to the decreased HC and CO emissions. CO from the standard hydroxygen-enriched gasoline engine is also lower than that from the hydrogen-enriched gasoline engine. But NOx emissions were increased after the hydroxygen addition.     

电控五气门汽油机稀燃与废气再循环性能对比研究

在一电控喷射稀薄燃烧五气门汽油机上，以稀薄燃烧汽油机电控开发系统及相应的废气再循环系统为试验平台，对五气门汽油机在各种进气模式下实施稀混合气燃烧及废气再循环时的燃油消耗率和排放性能进行了详细的试验研究，进而对本发动机的稀燃性能与废气再循环性能进行了比较，分析实施不同方法对发动机性能的不同影响效果，实验结果表明，采用分层EGR技术以后，EGR比率可达32％，稀燃和分层废气再循环都有效地降低了NOx排放，分层废气再循环对NOx降低的效果更为明显，而且降低速度更快，尤其在中、低负荷，可以使排气中的NOx降低85％～95％．对于油耗，稀燃的效果显然要好于废气再循环，在较高负荷尤为明显，稀燃可显著降低HC、CO，分层EGR对HC、CO排放降低幅度不大。     

Experimental and numerical investigation of effects of CNG and gasoline fuels on engine performance and emissions in a dual sequential spark ignition engine

Compared to widening usage of CNG in commercial gasoline engines, insufficient but increasing number of studies have appeared in open literature during last decades while engine characteristics need to be quantified in exact numbers for each specific fuel converted engine. In this study, a dual sequential spark ignition engine (Honda L13A4 i-DSI) is tested separately either with gasoline or CNG at wide open throttle. This specific engine has unique features of dual sequential ignition with variable timing, asymmetrical combustion chamber, and diagonally positioned dual spark-plug. Thus, the engine led some important engine technologies of VTEC and VVT. Tests are performed by varying the engine speed from 1500 rpm to 4000 rpm with an increment of 500 rpm. The engine’s maximum torque speed of 2800 rpm is also tested. For gasoline and CNG fuels, engine performance (brake torque, brake power, brake specific fuel consumption, brake mean effective pressure), emissions (O₂, CO₂, CO, HC, NO_x, and lambda), and the exhaust gas temperature are evaluated. In addition, numerical engine analyses are performed by constructing a 1-D model for the entire test rig and the engine by using Ricardo-Wave software. In the 1-D engine model, same test parameters are analyzed, and same test outputs are calculated. Thus, the test and the 1-D engine model are employed to quantify the effects of gasoline and CNG fuels on the engine performance and emissions for a unique engine. In general, all test and model results show similar and close trends. Results for the tested commercial engine show that CNG operation decreases the brake torque (12.7%), the brake power (12.4%), the brake mean effective pressure (12.8%), the brake specific fuel consumption (16.5%), the CO₂ emission (12.1%), the CO emission (89.7%). The HC emission for CNG is much lower than gasoline. The O₂ emission for CNG is approximately 55.4% higher than gasoline. The NO_x emission for CNG at high speeds is higher than gasoline. The variation percentages are the averages of the considered speed range from 1500 rpm to 4000 rpm.     

喷油定时对ＣＡ１１０２Ｑ５气门汽油机稀薄燃烧性能影响的试验研究

对ＣＡ１１０２Ｑ５气门汽油机采用稀薄燃烧时喷油定时对燃烧稳定性以及油耗、经济性的影响进行了细致的试验研究。试验结果表明,对于２种不同的进气模式,在部分负荷下采用稀燃时,喷油定时对二进气模式燃烧稳定性的影响比三进气模式大;在发动机燃用稀薄混合气时,喷油定时对排放和经济性的影响较为明显。     

直喷式汽油机缸内浓度场数值模拟

对直喷式二冲程汽油机缸内浓度场进行了数值模拟,选取两种代表性的发动机工况,采用球顶燃烧室,改变喷油定时和喷雾方向,研究它们对燃烧室内混合气浓度分布的影响。通过仿真分析得到:喷油定时和喷油方向对缸内浓度场分布有很大影响。当喷油器的中心轴线与气缸中心轴线的夹角为15°的喷油方向,喷油定时在低负荷选择95°CA、高负荷选择160°CA时,可以在火花塞附近形成有利于点火的混合气浓度,在整个燃烧室形成有利于分层燃烧的浓度场分布。     

Performance,combustion and emission characteristics of a spark‐ignition engine with simultaneous injection of n‐butanol and gasoline in comparison to blended butanol and gasoline

Simultaneous injection of n‐butanol and gasoline through a new system of two injectors directing the sprays towards the back of the intake valve in a spark‐ignition engine was tried in lieu of injecting a blend of these fuels through a single injector. This system avoids the problem of phase separation, which is generally faced during the use of alcohol‐gasoline blends. Experiments were conducted on a spark‐ignition engine with this dual injection system using a fuel ratio of 1:1 (B50S) on the mass basis. High‐speed photographs indicated that the sprays from the injectors did not interfere till they reached the intake valve. Comparisons were made with pre‐blended butanol‐gasoline (B50) and neat (100%) gasoline at the best spark timing. All injection and spark parameters were controlled using a real time engine controller. Neat n‐butanol (B100) was superior only near full throttle with improved efficiency of the engine of about 1.2% (absolute). Heat release rates were observed to be higher and more advanced with B100 at wide open throttle. However, a reverse of this trend was observed at the throttle position of 15%. NO emission was also lower by 30% with B100 at wide open throttle as compared with gasoline. However, a small increase in carbon monoxide (CO) levels was observed because of lower post combustion temperatures as compared with gasoline and B50S. Simultaneous injection reduced hydrocarbon (HC) emissions by 13% to 50% as compared with B50 (blended fuel). HC emissions with gasoline and B50S were similar. Nitric oxide (NO) emission was lower with B50S as compared with gasoline; however it was higher than B50 because of better combustion. On the whole, the developed dual injection system was superior to the conventional method of blending in terms of performance, emissions and ability to change the fuel ratio as needed. B50S is suitable at all throttle positions, whereas B100 shows benefits at full throttle conditions. Copyright © 2013 John Wiley & Sons, Ltd.