Process and device characterization of high voltage gallium arsenide P-i-N layers grown by an improved liquid phase epitaxy method

GaAs P-i-N layers with an i-region net doping of less than 10¹² cm⁻³ were grown on P⁺ and N⁺ substrates by a modified liquid phase epitaxy (LPE) method. Doping profiles and structural data obtained by varius characterization techniques are presented and discussed. A P⁺-P-i-N-N⁺ diode with a 25 μm-wide i-region exhibits a breakdown voltage of 1000 V, a t_rr of 50 ns, and reverse current densities (at V_R = 800 V) of − 3 × 10⁻⁶ A/cm² at 25°C and 10⁻² A/cm² at 260° C.     

Estimation for the capture cross-sections of surface state on p-Si surface by photovoltaic method

A new method which can nondestructively measure the surface-state density (SSD) D_s and estimate the capture cross-sections (CCS) of surface state σ⁰_n and σ⁻_p on surface of p-type semiconductor crystals is proposed. This method is based on the photovoltage measurements at various temperatures. The photovoltage experiment was carried out with a (1 1 1) p-type Si single crystal (N_A=4.8×10¹⁴ cm ⁻³). Owing to that the surface barrier height φ_BP=0.6421 V and the surface-recombination velocity s_n=9.6×10³ cm s⁻¹ of this sample can be determined, the SSD D_s=1.2×10¹¹ cm⁻² eV⁻¹ can therefore be obtained, furthermore CCS σ⁰_n≈5×10⁻¹⁴ cm² and σ⁻_p≈2×10⁻¹⁰ cm² can also be estimated. These results are consistent with that of related reports obtained by other methods.     

Measurement of low densities of surface states at the Si---SiO2-interface

By a careful process Si---SiO₂-interfaces can be made with a low oxide charge Q_ox and with a low surface states density N_ss. For dry oxides on (100) N_ss-values as low as a few 10⁹ cm⁻² eV⁻¹ are found on samples with an oxide charge density of 3·0 × 10¹⁰ cm⁻². Only the Nicollian-Goetzberger conductance method is proved to give reasonable results on these structures. The quasi-static low frequency C-V-technique is in good agreement with the conductance technique for samples with N_ss-values higher than 1·0 × 10¹⁰ cm⁻² eV⁻¹. The spatial fluctuation of surface potential, mainly caused by oxide charge fluctuations, is an important parameter when studying the high or low frequency C-V-characteristics. Some irregularities in the experimental N_ss-φ_s-curves are explained.     

Optoelectronic properties of Zn0.52Se0.48/Si Schottky diodes

Zn_0.52Se_0.48/Si Schottky diodes are fabricated by depositing zinc selenide (Zn_0.52Se_0.48) thin films onto Si(1 0 0) substrates by vacuum evaporation technique. Rutherford backscattering spectrometry (RBS) analysis shows that the deposited films are nearly stoichiometric in nature. X-ray diffractogram of the films reveals the preferential orientation of the films along (1 1 1) direction. Structural parameters such as crystallite size (D), dislocation density (δ), strain (ε), and the lattice parameter are calculated as 29.13 nm, 1.187 × 10⁻¹⁵ lin/m², 1.354 × 10⁻³ lin⁻² m⁻⁴ and 5.676 × 10⁻¹⁰ m respectively. From the I–V measurements on the Zn_0.52Se_0.48/p-Si Schottky diodes, ideality and diode rectification factors are evaluated, as 1.749 (305 K) and 1.04 × 10⁴ (305 K) respectively. The built-in potential, effective carrier concentration (N_A) and barrier height were also evaluated from C–V measurement, which are found to be 1.02 V, 5.907 × 10¹⁵ cm⁻³ and 1.359 eV respectively.     

Schottky barrier height of a new ohmic contact NiSi2 to n-type 6H-SiC

We present a new ohmic contact material NiSi₂ to n-type 6H-SiC with a low specific contact resistance. NiSi₂ films are prepared by annealing the Ni and Si films separately deposited on (0 0 0 1)-oriented 6H-SiC substrates with carrier concentrations (n) ranging from 5.8×10¹⁶ to 2.5×10¹⁹ cm⁻³. The deposited films are annealed at 900 °C for 10 min in a flow of Ar gas containing 5 vol.% H₂ gas. The specific contact resistance of NiSi₂ contact exponentially decreases with increasing carrier concentrations of substrates. NiSi₂ contacts formed on the substrates with n=2.5×10¹⁹ cm⁻³ show a relatively low specific contact resistance with 3.6×10⁻⁶ Ω cm². Schottky barrier height of NiSi₂ to n-type 6H-SiC is estimated to be 0.40±0.02 eV using a theoretical relationship for the carrier concentration dependence of the specific contact resistance.     

Characterization of phosphorus implanted low pressure chemical vapor deposited polycrystalline silicon

Thin (3000–5000Å) low pressure chemically vapor deposited (LPCVD) films of polycrystalline silicon suitable for microelectronics applications have been deposited from silane at 600°C and at a pressure of 0.25 Torr. The films were phosphorus implanted at 150 KeV and electrically characterized with the annealing conditions and film thickness as parameters, over a resistivity range of four orders of magnitude (10³–10⁷Ω/□). Annealing during silox deposition was found to result in a lower film resistivity than annealing done in nitrogen atmosphere. Resistivity measurements as a function of temperature indicate that the electrical activation energy is a linear function of 1/N(N is the doping concentration), changing from 0.056 eV for a doping concentration of 8.9 × 10¹⁸ cm⁻³ to 0.310 eV for doping concentration of 3.3 × 10¹⁸ cm⁻³. The grain boundary trap density was found to have a logarithmically decreasing dependence on the polysilicon thickness, decreasing from 1.3 × 10¹³ cm⁻² for 2850Å polysilicon film to 8.3 × 10¹² cm⁻² for 4500Å polysilicon film.     

Characteristics of polycrystalline films grown by ultrahigh vacuum chemical vapor deposition system

In situ boron-doped polycrystalline Si_1−xGe_x (poly-Si_1−xGe_x) films deposited by ultrahigh vacuum chemical vapor deposition (UHV/CVD) system were characterized. Optimum fitted values of grain boundary trap state densities, 4.0 × 10¹² cm⁻² and 4.9 × 10¹² cm⁻² were obtained for poly-Si and poly-Si_0.79Ge_0.21, respectively. The extracted average carrier concentration in the grain agrees with secondary ion mass spectroscopy (SIMS) analysis. In turn, we found that these films are suitable Hall elements to sense magnetic field. Experimental results show that the sensitivity decreased with the increasing input current, which can be well explained using the thermionic emission theory. Finally, we use these films to fabricate thin film transistors.     

A study of noise in surface and buried channel SiGe MOSFETs with gate oxide grown by low temperature plasma anodization

A study is made of noise in p- and n-channel transistors incorporating SiGe surface and buried channels, over the frequency range f=1 Hz–100 kHz. The gate oxide is grown by low temperature plasma oxidation. Surface n-channel devices are found to exhibit two noise components namely 1/f and generation–recombination (GR) noise. It is shown that the 1/f noise component is due to fluctuations of charge in slow oxide traps whilst bulk centers located in a thin layer of the semiconductor close to the channel, give rise to the GR noise component. The analysis of the noise data gives values for the density D_ot of the oxide traps in the SiGe and Si nMOSFETs of the order 1.8×10¹² and 2.5×10¹⁰ cm⁻² (eV)⁻¹, respectively. The density D_GR of the bulk GR centres is equal to 3×10¹⁰ cm⁻² in both the SiGe and Si devices. The electron and hole capture cross-sections for these centres as well as their energy level and their depth below the oxide/semiconductor interface are also the same in the devices of both types. This suggests that those GR centers are of the same nature in all devices studied. p-Channel devices show different behaviour with only a 1/f noise component apparent in the data over the same frequency range. Buried SiGe channel and Si control devices exhibit quite low and similar slow state densities of the order low to mid 10¹⁰ cm⁻² (eV)⁻¹ whereas surface p-channel devices show even higher slow state densities than n-channel counterparts. The Hooge noise characterized by the Hooge coefficient _H=2×10⁻⁵ is also detected in some buried p-channel SiGe devices.     

Thin oxide grown on heavily channel-implanted substrate by using a low temperature wafer loading and N2 pre-annealing process

In this paper, we present high integrity thin oxides grown on the channel implanted substrate (3 × 10¹⁷ cm⁻³) and heavily doped substrate (1 × 10²⁰ cm⁻³) by using a low-temperature wafer loading and N₂ pre-annealing process. The presented thin oxide grown on the channel implanted substrate exhibits a very low interface state density (1 × 10¹⁰ cm⁻² eV⁻¹) and a very high intrinsic dielectric breakdown field (15 MV/cm). It also shows a lower charge trapping rate and interface state generation rate than the conventional thermal oxide. For the thin oxide grown on the heavily-doped substrate by using the proposed recipe, the implantation-induced damage close to the silicon surface can be almost annealed out. The presented heavily-doped oxide shows much better dielectric characteristics, such as the dielectric breakdown field and the charge-to-breakdown, as compared to the conventional heavily-doped oxide.     

GaN p–n junction diode formed by Si ion implantation into p-GaN

²⁸Si⁺ implantation into Mg-doped GaN, followed by thermal annealing in N₂ was performed to achieve n⁺-GaN layers. The carrier concentrations of the films changed from 3×10¹⁷ (p-type) to 5×10¹⁹ cm⁻³ (n-type) when the Si-implanted p-type GaN was properly annealed. Specific contact resistance (ρ_c) of Ti/Al/Pt/Au Ohmic contact to n-GaN, formed by ²⁸Si⁺ implantation into p-type GaN, was also evaluated by transmission line model. It was found that we could achieve a ρ_c value as low as 1.5×10⁻⁶ Ω cm² when the metal contact was alloyed in N₂ ambience at 600 °C. Si-implanted GaN p–n junction light-emitting diodes were also fabricated. Electroluminescence measurements showed that two emission peaks at around 385 and 420 nm were observed, which could be attributed to the near band-edge transition and donor-to-acceptor transition, respectively.     

On the behaviour of buried oxygen implanted layers in highly doped GaAs

Highly doped GaAs substrate material (doping level 10¹⁸ cm⁻³) has been implanted with 350 keV O⁺ ions with doses of 10¹⁴ – 10¹⁶ cm⁻² to produce high resistivity layers which are stable at high temperatures. LPE growth of flat GaAs epilayers onto the implanted wafers was achieved up to doses of about 1 × 10¹⁵ O⁺/cm² and 5 × 10¹⁵O⁺/cm² for RT and 200°C implants, respectively. N-o-n and p-o-n structures (o: oxygen implanted) were fabricated in which breakdown voltages of up to 15 V were obtained. Examples for application of this isolation technique are shown.     

n-Channel AlSb/GaSb modulation-doped field-effect transistors

We report the first fabrication of a GaSb n-channel modulation-doped field-effect transistor (MODFET) grown by molecular beam epitaxy. The modulation-doped structure exhibits a room temperature Hall mobility of 3140 cm² V⁻¹ s⁻¹ and 77 K value of 16000 cm² V⁻¹ s⁻¹, with corresponding sheet carrier densities of 1.3 × 10¹² cm⁻² and 1.2 × 10¹² cm⁻². Devices with 1 μm gate length yield transconductances of 180 mS mm⁻¹ and output of 5 mS mm⁻¹ at 85 K. The device characteristics indicate that electron transport in the channel occurs primarily via the L-valley of GaSb above 85 K. The effective electron saturation velocity is estimated to be 0.9 × 10⁷ cm s⁻¹. Calculations show that a complementary circuit consisting of GaSb n- and p-channel MODFETs can provide at least two times improvement in performance over AlGaAs/GaAs complementary circuits.     

Selenium doped high-index GaAs epilayers grown by molecular beam epitaxy

Using elementary Se we grew Se-doped GaAs films on GaAs (111), (411), (711) and (100) substrates by molecular beam epitaxy. The films grown on all the high-index substrates showed n-type conduction and the maximum carrier concentration reached 2.1 × 10¹⁹ cm⁻³ for the film grown on the (411)B substrate. The carrier concentration began to saturate at a Se concentration near 10¹⁹ cm⁻³ but continued to increase up to a Se concentration of 2 × 10²⁰ cm⁻³. Above 2 × 10²⁰ cm⁻³ Se concentration, slow reduction of the carrier concentration was observed. We obtained excellent surface morphology when n-type GaAs films were grown on (411)A and (711)B substrates even at a Se concentration of 7 × 10²⁰ cm⁻³.     

The physics and fabrication of in situ back-gated (311)A hole gas heterojunctions

This paper reports the fabrication of an in situ back-gated hole gas on the (311)A surface of GaAs. The hole density can be varied from fully depleted to p_s = 2.1 × 10¹¹ cm⁻² with mobilities of up to μ = 1.1 × 10⁶ cm²V⁻¹ s⁻¹. It is seen that for carrier densities down to p_s = 4 × 10¹⁰ cm⁻² the mobility in the [ ] direction is greater than that in the [ ] direction. Using a combination of front- and back-gates we are able to keep the carrier density constant and deform the hole gas wavefunction such that the holes are pushed up against or moved further away from the heterointerface. Thus we are able to separately investigate the various scattering mechanisms that determine the mobility, and compare the experimental data with theoretical calculations based on the shape of the wavefunction.     

Carrier recombination in single crystal PbSe

The photoconductivity decay curves after illumination of single crystal n- and p-type PbSe were analysed assuming recombination through different localized impurity levels in conjunction with direct recombination. The lifetimes deduced for direct (Auger and radiative) recombination below 250 K were in agreement with the calculated values for carrier concentrations 2·10¹⁷ cm⁻³. Furthermore, the existence of up to three impurity levels was concluded from the longer lifetime-components present in the decay curves. Appropriate approximations of the general recombination theory yielded energies separated between 20 and 50 meV from the nearer band edge and minority carrier cross sections 10⁻¹⁷−4·10⁻¹⁹ cm² in the temperature range 250-100 K, and majority carrier cross sections 10⁻¹⁹−10⁻²⁰ cm² at T < 100 K for these levels.     

Interface characteristics of Ge3N4-(n-type) GaAs MIS devices

Passivation of GaAs surfaces was achieved by the deposition of Ge₃N₄ dielectric films at low temperatures. Electrical characteristics of MIS devices were measured to determine the interface parameters. From C-V-f and G-V-f measurements, density of interface states has been obtained as (4–6)×10¹¹ cm⁻² eV⁻¹ at the semiconductor mid-gap. Some inversion charge buildup was seen in the C-V plot although the strong inversion regime is absent. Thermally stimulated current measurements indicate a trap density of 5×10¹⁸−10¹⁹ cm⁻³ in the dielectric film, with their energy level at 0.59 eV.     

Cyclotron oscillations in a tilted magnetic field: A tool to measure the mean free path of ballistic electrons in high purity GaAs

The mean free path (mfp) of ballistic electrons in high purity GaAs was measured using a novel effect due to the cyclotron motion of ballistic electrons in tilted magnetic fields. Whenever the cyclotron orbit is commensurate with the device length an increase in the collected current is observed, leading to pronounced oscillations. We utilize the fact that the total path length varies as we change the angle of the magnetic field to extract the mfp using a single device. For high purity GaAs with an impurity concentration N_a+N_d≈6 × 10¹⁴ cm⁻³ we measure an mfp of ≈4 μm for electrons below the optical phonon energy. We suggest that the observed mfp is primarily due to impact ionization of neutral donors by the ballistic electrons. The large contrast of the oscillations proves that both injection and collection give preference to the direction normal to the layers and thus, that the momentum component parallel to the layers is conserved during transmission over the barrier.     

Intersubband lifetimes in Si/SiGe quantum wells

In the present work we report the first measurement of intersubband lifetimes in Si/Si_1−xGe_x quantum well samples. We have determined T₁ by a time resolved pump and probe experiment using the far infrared picosecond free electron laser source FELIX at Rijnhuizen, the Netherlands. In a sample with a well width of 50 Å and a sheet density of 2.1 × 10¹² cm⁻² we find a lifetime of 30 ps while 20 ps is observed for a density of 1.1 × 10¹² cm⁻² and a well width of 75 Å. We discuss acoustic phonon, as well as optical phonon intersubband scattering as possible limiting processes for the observed lifetimes in Si/SiGe and GaAs/AlGaAs quantum wells.     

Electrical, structural, and optical characterization of free-standing GaN template grown by hydride vapor phase epitaxy

Electrical, structural, and optical properties of a free-standing 200 μm thick n-type GaN template grown by hydride vapor phase epitaxy have been investigated. Hall mobilities of 1100 and 6800 cm²/V s have been obtained at room temperature and 50 K, respectively. Quantitative analysis of acceptor concentration, donor concentration and donor activation energy has been conducted through simultaneous fitting of the temperature dependent Hall mobility and carrier concentration data which led to a donor concentration of 2.10×10¹⁶ cm⁻³ and an acceptor concentration of 4.9×10¹⁵ cm⁻³. The resultant donor activation energy is 18 meV. The analysis indicates that the dominant scattering mechanism at low temperatures is by ionized impurities. The extended defect concentrations on Ga- and N-faces were about 5×10⁵ cm⁻² for the former and about 1×10⁷ cm⁻² for the latter, as revealed by a chemical etch. The full width at half maximum of the symmetric (0 0 0 2) X-ray diffraction peak was 69″ and 160″ for the Ga- and N-faces, respectively. That for the asymmetric (10–14) peak was 103″ and 140″ for Ga- and N-faces, respectively. The donor bound exciton linewidth as measured on the Ga- and N-face (after a chemical etch to remove the damage) is about 1 meV each at 10 K. Instead of the commonly observed yellow band, this sample displayed a green band, which is centered at about 2.45 eV.     

Determination of the LO-phonon and Γ→L intervalley scattering time in GaAs from hot electron luminescence spectroscopy

Both the LO-phonon scattering time and the Γ→L intervalley scattering time for electrons in the conduction band of GaAs are of fundamental importance, and they are needed for the modelling of devices. We measure the steady state distribution of hot electrons in lightly p-doped bulk GaAs under carrier densities of 10¹³–10¹⁴cm⁻³, which is orders of magnitude lower than in pulsed laser experiments. Using a 16×16 k.p Hamiltonian and taking into account the transition matrix elements in a dipole model, we determine the hot electron lifetime from comparison with the experimentally found lifetime broadening. For electrons with a kinetic energy of 100meV to 300meV we obtain τ_LO=(132±10)fs. We also determine the Γ→L intervalley separation as E_ΓL=(300±10)meV. We find Γ→L scattering times around 150fs to 200fs, corresponding to a value for the associated deformation potential of D_ΓL=(9.4±1.5)×10⁸eV/cm.