Removal of copper(II) and lead(II) from aqueous solution by manganese oxide coated sand I. Characterization and kinetic study

The preparation, characterization, and sorption properties for Cu(II) and Pb(II) of manganese oxide coated sand (MOCS) were investigated. A scanning electron microscope (SEM), X-ray diffraction spectrum (XRD) and BET analyses were used to observe the surface properties of the coated layer. An energy dispersive analysis of X-ray (EDAX) and X-ray photoelectron spectroscopy (XPS) were used for characterizing metal adsorption sites on the surface of MOCS. The quantity of manganese on MOCS was determined by means of acid digestion analysis. The adsorption experiments were carried out as a function of solution pH, adsorbent dose, ionic strength, contact time and temperature. Binding of Cu(II) and Pb(II) ions with MOCS was highly pH dependent with an increase in the extent of adsorption with the pH of the media investigated. After the Cu(II) and Pb(II) adsorption by MOCS, the pH in solution was decreased. Cu(II) and Pb(II) uptake were found to increase with the temperature. Further, the removal efficiency of Cu(II) and Pb(II) increased with increasing adsorbent dose and decreased with ionic strength. The pseudo-first-order kinetic model, pseudo-second-order kinetic model, intraparticle diffusion model and Elovich equation model were used to describe the kinetic data and the data constants were evaluated. The pseudo-second-order model was the best choice among all the kinetic models to describe the adsorption behavior of Cu(II) and Pb(II) onto MOCS, suggesting that the adsorption mechanism might be a chemisorption process. The activation energy of adsorption (E(a)) was determined as Cu(II) 4.98 kJ mol(-1) and Pb(II) 2.10 kJ mol(-1), respectively. The low value of E(a) shows that Cu(II) and Pb(II) adsorption process by MOCS may involve a non-activated chemical adsorption and a physical sorption.     

Copper(II) and lead(II) removal from aqueous solution in fixed-bed columns by manganese oxide coated zeolite

The ability of manganese oxide coated zeolite (MOCZ) to adsorb copper and lead ions in single- (non-competitive) and binary- (competitive) component sorption systems was studied in fixed-bed column. The experiments were applied to quantify particle size, bed length, influent flow rate and influent metal concentration on breakthrough time during the removal of copper and lead ions from aqueous solutions using MOCZ column. Results of fixed-bed adsorption showed that the breakthrough time appeared to increase with increase of the bed length and decrease of influent metal concentration, but decreased with increase of the flow rate. The Thomas model was applied to adsorption of copper and lead ions at bed length, MOCZ particle size, different flow rate and different initial concentration to predict the breakthrough curves and to determine the characteristic parameters of the column useful for process design. The model was found suitable for describing the adsorption process of the dynamic behavior of the MOCZ column. The total adsorbed quantities, equilibrium uptakes and total removal percents of Cu(II) and Pb(II) related to the effluent volumes were determined by evaluating the breakthrough curves obtained at different conditions. The results suggested that MOCZ could be used as an adsorbent for an efficient removal of copper and lead ions from aqueous solution. The removal of metal ion was decreased when other additional heavy metal ion was added, but the total saturation capacity of MOCZ for copper and lead ions was not significantly decreased. This competitive adsorption also showed that adsorption of lead ions was decreased insignificantly when copper ions was added to the influent, whereas a dramatic decrease was observed on the adsorption of copper ions by the presence of lead ions. The removal of copper and lead ion by MOCZ columns followed the descending order: Pb(II) > Cu(II). The adsorbed copper and lead ions were easily desorbed from MOCZ with 0.5 mol l(-1) HNO3 solution.     

Removal of copper(II) from aqueous solution by Jordanian pottery materials

The aim of this work was to assess the possibility of removing some heavy metals from water by a low-cost adsorbent, like Jordanian raw pottery. Five types of raw and modified pottery materials have been investigated. The effects of initial metal concentration, agitation time, pH and temperature on the removal of Cu(II) were studied. A pseudo-first order was used to test the adsorption kinetics. In order to investigate the sorption isotherm, two equilibrium models, the Freundlich and Langmuir isotherms, were analyzed. The effect of solution pH on the adsorption onto pottery was studied in the pH range 1-5. The adsorption was exothermic at ambient temperature and the computation of the parameters, DeltaH, DeltaS and DeltaG, indicated the interactions to be thermodynamically favorable.     

Equilibrium, kinetic and thermodynamic studies of adsorption of Pb(II) from aqueous solution onto Turkish kaolinite clay

The adsorption of Pb(II) onto Turkish (Bandirma region) kaolinite clay was examined in aqueous solution with respect to the pH, adsorbent dosage, contact time, and temperature. The linear Langmuir and Freundlich models were applied to describe equilibrium isotherms and both models fitted well. The monolayer adsorption capacity was found as 31.75 mg/g at pH 5 and 20 degrees C. Dubinin-Radushkevich (D-R) isotherm model was also applied to the equilibrium data. The mean free energy of adsorption (13.78 kJ/mol) indicated that the adsorption of Pb(II) onto kaolinite clay may be carried out via chemical ion-exchange mechanism. Thermodynamic parameters, free energy (deltaG degrees ), enthalpy (deltaH degrees ) and entropy (deltaS degrees ) of adsorption were also calculated. These parameters showed that the adsorption of Pb(II) onto kaolinite clay was feasible, spontaneous and exothermic process in nature. Furthermore, the Lagergren-first-order, pseudo-second-order and the intraparticle diffusion models were used to describe the kinetic data. The experimental data fitted well the pseudo-second-order kinetics.     

Removal of Pb(II) from aqueous solution using modified and unmodified kaolinite clay

Modified kaolinite clay with 25% (w/w) aluminium sulphate and unmodified kaolin were investigated as adsorbents to remove Pb(II) from aqueous solution. The results show that amount of Pb(II) adsorbed onto modified kaolin (20 mg/g) was more than 4.5-fold than that adsorbed onto unmodified kaolin (4.2 mg/g) under the optimized condition. In addition, the linear Langmuir and Freundlich models were used to describe equilibrium isotherm. It is observed that the data from both adsorbents fitted well to the Langmuir isotherm. The kinetic adsorption of modified and unmodified kaolinite clay fitted well to the pseudo-second-order model. Furthermore, both modified and unmodified kaolinite clay were characterized by X-ray diffraction, Fourier transform infrared (FT-IR) and scanning electron microscope (SEM). Finally, both modified and unmodified kaolinite clay were used to remove metal ions from real wastewater, and results show that higher amount of Pb(II) (the concentration reduced from 178 to 27.5 mg/L) and other metal ions were removed by modified kaolinite clay compared with using unmodified adsorbent (the concentration reduced from 178 to 168 mg/L).     

Experimental determination of equilibrium constant for the complexing reaction of nitric oxide with hexamminecobalt(II) in aqueous solution

Ammonia solution can be used to scrub NO from the flue gases by adding soluble cobalt(II) salts into the aqueous ammonia solutions. The hexamminecobalt(II), Co(NH3)6(2+), formed by ammonia binding with Co2+ is the active constituent of eliminating NO from the flue gas streams. The hexamminecobalt(II) can combine with NO to form a complex. For the development of this process, the data of the equilibrium constants for the coordination between NO and Co(NH3)6(2+)over a range of temperature is very important. Therefore, a series of experiments were performed in a bubble column to investigate the chemical equilibrium. The equilibrium constant was determined in the temperature range of 30.0-80.0 degrees C under atmospheric pressure at pH 9.14. All experimental data fit the following equation well: [formula: see text] where the enthalpy and entropy are DeltaH degrees = - (44.559 +/- 2.329)kJ mol(-1) and DeltaS degrees = - (109.50 +/- 7.126) J K(-1)mol(-1), respectively.     

Removal of Cu(II) from aqueous solution by adsorption onto acid-activated palygorskite

A series of activated palygorskite clay by HCl with different concentrations was prepared and applied as adsorbents for removal of Cu(II) from aqueous solutions. The effects of contact time, adsorbent dosages and pHs of suspension on the adsorption capacities for Cu(II) were investigated. The results showed that adsorption capacity of activated palygorskites increased with increasing the HCl concentration and the maximum adsorption capacity with 32.24 mg/g for Cu(II) is obtained at 12 mol/L of HCl concentration. The variations in IR spectra and pH of solution after adsorption Cu(II) confirmed that the numerous amount of silanol groups (Si-OH) originated by acid treatment were mainly responsible for Cu(II) adsorption onto acid-activated palygorskite. Kinetic studies indicated that the adsorption mechanisms in the Cu(II)/acid-activated palygorskite system followed the pseudo-second-order kinetic model with a relatively small contribution of film diffusion. Equilibrium data fitted well with Freundlich isotherm model compared to Langmuir isotherm model, indicating that adsorption takes place on heterogeneous surfaces of the acid-activated palygorskite. Adsorption-desorption studies presented that activated palygorskite has lower adsorption and desorption efficiencies using Cu(CH3COO)2 than that of other inorganic copper salts, such as CuSO4, Cu(NO3)2, and CuCl2.     

Removal of Cu(II) ions by activated poplar sawdust (Samsun clone) from aqueous solutions

In this work, adsorption of Cu(II) ions on sawdust (SD) and activated sawdust (ASD) has been studied by using batch adsorption techniques. The equilibrium adsorption level was determined to be a function of the pH, initial Cu(II) concentration, and adsorbent dosage. The equilibrium nature of Cu(II) adsorption has been described by the Freundlich and Langmuir isotherms. The experimental adsorption data were fitted to the Langmuir adsorption model both sawdust and activated sawdust. The equilibrium capacity of sawdust and activated sawdust were 5.432 and 13.495 mg copper per g adsorbent, respectively at room temperature and natural pH. The maximum adsorption capacity was obtained at the maximum zeta potential value that -74.5 mV (pH 5) for activated sawdust and at -48.4 mV (pH 4) for sawdust. It was observed that activated sawdust was a suitable adsorbent than sawdust for removal of Cu(II) from aqueous solutions.     

Removal of Ni(II), Zn(II) and Cr(VI) from aqueous solution by Alternanthera philoxeroides biomass

Alternanthera philoxeroides biomass, a type of freshwater macrophyte, was used for the sorptive removal of Ni(II), Zn(II) and Cr(VI) from aqueous solutions. Variables of the batch experiments include solution pH, contact time, particle size and temperature. The biosorption capacities are significantly affected by solution pH. Higher pH favors higher Ni(II), Zn(II) removal, whereas higher uptake of Cr(VI) is observed as the pH is decreased. A two-stage kinetic behavior is observed in the biosorption of Ni(II), Zn(II) and Cr(VI): very rapid initial biosorption in a few minutes, followed by a long period of a slower uptake. It is noted that an increase in temperature results in a higher Ni(II), Zn(II) and Cr(VI) loading per unit weight of the sorbent. Decreasing the particle sizes of the Alternanthera philoxeroides biomass leads to an increase in the Ni(II), Zn(II) and Cr(VI) uptake per unit weight of the sorbent. All isothermal data are fairly well fitted with Langmuir equations. The thermodynamic parameter, DeltaG degrees, were calculated. The negative DeltaG degrees values of Cr(VI), Ni(II) and Zn(II) at various temperatures confirm the adsorption processes are spontaneous.     

Biosorption of cadmium (II) and lead (II) from aqueous solutions using mushrooms: A comparative study

Sorption capacity of oyster mushroom (Pleurotus platypus), button mushroom (Agaricus bisporus) and milky mushroom (Calocybe indica) were evaluated on biosorption of heavy metals, viz. cadmium (II) and lead (II) from aqueous solutions. The optimum sorption conditions were studied for each metal separately. The desired pH of the aqueous solution was found to be 6.0 for the removal of cadmium (II) and 5.0 for removal of lead (II) for all the mushrooms. The percent removal of both the metals was found to increase with the increase in biosorbent dosage and contact time. The fitness of the biosorption data for Langmuir and Freundlich adsorption models was investigated. It was found that biosorption of cadmium (II) and lead (II) ions onto the biomass of the three mushrooms were better suitable to Langmuir than Freundlich adsorption model. P. platypus showed the highest metal uptake potential for cadmium (q_max 34.96 mg/g) whereas A. bisporus exhibited maximum potential for lead (q_max 33.78 mg/g). Milky mushroom showed the lowest metal uptake capacity for both the metals. The present data confirms that mushrooms may be used as efficient biosorbent for the removal of cadmium (II) and lead (II) ions from aqueous solution.     

Sorption profile of Cd(II) ions onto beach sand from aqueous solutions

Sorption of traces of Cd(II) ions onto beach sand is investigated as a function of nature and concentration of electrolyte (10(-4) to 10(-2)M nitric, hydrochloric and perchloric acids, pH 2-10 buffers and deionized water), shaking time 5-40min, shaking speed 50-200strokes/min, dosage of sand (50-1000mg/15cm(3)), concentration of sorbate (1.04x10(-6) to 1.9x10(-4)M) and temperature (293-323K). Maximum sorption of Cd(II) ions (approximately 66%) is achieved from deionized water using 300mg/15cm(3) sand in 20min. The data are successfully tested by Langmuir, Freundlich and Dubinin-Redushkevich (D-R) sorption isotherms. The values for characteristic Langmuir constants Q=13.31+/-0.20micromol/g and of b=(6.56+/-0.53)x10(3)dm(3)/mol, Freundlich constants A=2.23+/-1.16mmol/g and 1/n=0.70+/-0.05 of (D-R) constants beta=-0.005068+/-0.000328kJ(2)/mol(2), X(m)=46.91+/-11.91micromol/g and energy E=9.92+/-0.32kJ/mol have been estimated. Kinetics of sorption has been studied by applying Morris-Weber, Richenberg and Lagergren equations. The sorption follows first order rate equation resulting 0.182+/-0.004min(-1) The thermodynamic parameters DeltaH=32.09+/-2.92kJ/mol, DeltaS=111.0+/-9.5J/molK and DeltaG=-1.68+/-0.02kJ/mol are evaluated. The influence of common ions on the sorption of Cd(II) ions is also examined. Some common ions reduce the sorption while most of the ions have very little effect. It can be concluded that beach sand may be used as an alternative for the expensive synthetic sorbents.     

涂铁多孔陶瓷吸附去除亚甲基蓝的热动力学

研究了涂铁多孔陶瓷(IOCPC)在20～40℃下对亚甲基蓝(MB)静态吸附的热动力学性质.用液相沉积、多次涂层法对赤泥质多孔陶瓷表面改性制备吸附剂,并通过小试摇床实验考察了IOCPC在不同条件下吸附MB的效果.结果表明:IOCPC的比表面积为4.987m2/g,比改性前增大3.28倍,平均孔径为11.36nm.IOCPC对MB的吸附等温线呈S型,Freundlich等温吸附方程和准二级动力学方程较好地描述了IOCPC对MB的吸附等温线及吸附动力学实验结果,相关系数分别＞0.89和0.97,平衡吸附容量随温度的升高而增加.由标准吉布斯自由能变(莫獹＜0 )、标准反应焓变(莫獺0＞0)和吸附活化能(Ea=16.145kJ/mol＞4.184kJ/mol)的值可判断,IOCPC对MB的吸附是自发的、吸热的化学吸附反应.     

Surface-functionalized pomelo peel-derived biochar with mercapto-1,2,4-triazloe for selective elimination of toxic Pb (II) in aqueous solutions

A novel biochar adsorbent (GP-AMT) is prepared by functionalizing biochar derived from pomelo peel to eliminate Pb (II) from water. GP-AMT was characterized by FTIR, SEM, BET, TGA and XPS. GP-AMT has a large specific area and is multiaperture. The adsorption performance was studied. At the pH = 5, the maximum uptake amount of Pb(II) on GP-AMT reached 420 mg/g. The sorption behavior of GP-AMT obeys with Langmuir and pseudo second-order formula, which shows that the adsorbing property of GP-AMT is uniform chemical sorption. Thermodynamic studies attested that the sorption was an irreversible endothermic course. GP-AMT demonstrated excellent selectivity and reproducibility. After 5 cycles, it still has an excellent sorption property. XPS and zeta potential analysis revealed that the adsorbing nature of GP-AMT for heavy metal ions was coordination and ion exchange. In conclusion, surface modification of biochar can significantly improve its sorption capacity, selectivity and regenerative ability for Pb(II), and reduce the pomelo peel waste pollution.     

Removal of copper from aqueous solution using Ulva fasciata sp.--a marine green algae

Batch adsorption experiments were carried out for the removal of copper from its aqueous solution using Ulva fasciata sp. a marine green algae as adsorbent. The adsorption of Cu(II) by Ulva fasciata sp. was investigated as a function of pH, contact time, initial Cu(II) and adsorbent concentrations and adsorbent size. About 0.1 g of Ulva fasciata sp. was found to be enough to remove 95% of 20 mg/L copper from 30 mL aqueous solution in 20 min. The optimum pH value was found to be 5. The dynamic data fitted to the pseudo-second order kinetic model. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The experimental adsorption data were fitted to the Langmuir adsorption model. The maximum adsorption capacity was 26.88 mg/g. The applicability of Lagergren kinetic model was also investigated.     

Competitive adsorption of copper(II), cadmium(II), lead(II) and zinc(II) onto basic oxygen furnace slag

Polluted and contaminated water can often contain more than one heavy metal species. It is possible that the behavior of a particular metal species in a solution system will be affected by the presence of other metals. In this study, we have investigated the adsorption of Cd(II), Cu(II), Pb(II), and Zn(II) onto basic oxygen furnace slag (BOF slag) in single- and multi-element solution systems as a function of pH and concentration, in a background solution of 0.01M NaNO(3). In adsorption edge experiments, the pH was varied from 2.0 to 13.0 with total metal concentration 0.84mM in the single element system and 0.21mM each of Cd(II), Cu(II), Pb(II), and Zn(II) in the multi-element system. The value of pH(50) (the pH at which 50% adsorption occurs) was found to follow the sequence Zn>Cu>Pb>Cd in single-element systems, but Pb>Cu>Zn>Cd in the multi-element system. Adsorption isotherms at pH 6.0 in the multi-element systems showed that there is competition among various metals for adsorption sites on BOF slag. The adsorption and potentiometric titrations data for various slag-metal systems were modeled using an extended constant-capacitance surface complexation model that assumed an ion-exchange process below pH 6.5 and the formation of inner-sphere surface complexes at higher pH. Inner-sphere complexation was more dominant for the Cu(II), Pb(II) and Zn(II) systems.     

Removal of chromium (VI) from aqueous solution using treated oil palm fibre

This study proposed an oil palm by-product as a low-cost adsorbent for the removal of hexavalent chromium [Cr (VI)] from aqueous solution. Adsorption of Cr (VI) by sulphuric acid and heat-treated oil palm fibre was conducted using batch tests. The influence of pH, contact time, initial chromium concentration and adsorbent dosage on the removal of Cr (VI) from the solutions was investigated. The optimum initial pH for maximum uptake of Cr (VI) from aqueous solution was found to be 1.5. The removal efficiency was found to correlate with the initial Cr (VI) concentration, adsorbent dosage as well as the contact time between Cr (VI) and the adsorbent. The adsorption kinetics tested with pseudo first order and pseudo second order models yielded high R(2) values from 0.9254 to 0.9870 and from 0.9936 to 0.9998, respectively. The analysis of variance (ANOVA) showed significant difference between the R(2) values of the two models at 99% confidence level. The Freundlich isotherm (R(2)=0.8778) described Cr (VI) adsorption slightly better than the Langmuir isotherm (R(2)=0.8715). Difficulty in desorption of Cr (VI) suggests the suitability of treated oil palm fibre as a single-use adsorbent for Cr (VI) removal from aqueous solution.     

Biosorption of Pb(II) and Cd(II) from aqueous solution using green alga (Ulva lactuca) biomass

The biosorption characteristics of Pb(II) and Cd(II) ions from aqueous solution using the green alga (Ulva lactuca) biomass were investigated as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by U. lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of U. lactuca biomass for Pb(II) and Cd(II) ions was found to be 34.7mg/g and 29.2mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 10.4kJ/mol for Pb(II) biosorption and 9.6kJ/mol for Cd(II) biosorption, indicating that the biosorption of both metal ions was taken place by chemisorption. The calculated thermodynamic parameters (DeltaG degrees , DeltaH degrees and DeltaS degrees ) showed that the biosorption of Pb(II) and Cd(II) ions onto U. lactuca biomass was feasible, spontaneous and exothermic under examined conditions. Experimental data were also tested in terms of biosorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the biosorption processes of both metal ions followed well pseudo-second-order kinetics.     

Adsorption of copper (II), chromium (III), nickel (II) and lead (II) ions from aqueous solutions by meranti sawdust

The present study proposed the use of meranti sawdust in the removal of Cu(II), Cr(III), Ni(II) and Pb(II) ions from synthetic aqueous solutions. Batch adsorption studies showed that meranti sawdust was able to adsorb Cu(II), Cr(III), Ni(II) and Pb(II) ions from aqueous solutions in the concentration range 1–200 mg/L. The adsorption was favoured with maximum adsorption at pH 6, whereas the adsorption starts at pH 1 for all metal ions. The effects of contact time, initial concentration of metal ions, adsorbent dosage and temperature have been reported. The applicability of Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherm was tried for the system to completely understand the adsorption isotherm processes. The adsorption kinetics tested with pseudo-first-order and pseudo-second-order models yielded high R² values from 0.850 to 0.932 and from 0.991 to 0.999, respectively. The meranti sawdust was found to be cost effective and has good efficiency to remove these toxic metal ions from aqueous solution.     

The study of adsorption characteristics Cu and Pb ions onto PHEMA and P(MMA-HEMA) surfaces from aqueous single solution

The adsorption characteristics of Cu²⁺ and Pb²⁺ ions onto poly2-hydroxyethyl methacrylate (PHEMA) and copolymer 2-hydroxyethyl methacrylate with monomer methyl methacrylate P(MMA-HEMA) adsorbent surfaces from aqueous single solution were investigated with respect to the changes in the pH of solution, adsorbent composition (changes in the weight percentage of MMA copolymerized with HEMA monomer), contact time and the temperature in the individual aqueous solutions. The linear correlation coefficients of Langmuir and Freundlich isotherms were obtained. The results revealed that the Langmuir isotherm fitted the experimental results better than the Freundlich isotherm. Using the Langmuir model equation, the monolayer adsorption capacity of PHEMA surface was found to be 0.840 and 3.037 mg/g for Cu²⁺ and Pb²⁺ ions and adsorption capacity of (PMMA-HEMA) was found to be 31.153 and 31.447 mg/g for Cu²⁺ and Pb²⁺ ions, respectively. Changes in the standard Gibbs free energy (ΔG⁰), standard enthalpy (ΔH⁰) and standard entropy (ΔS⁰) show that the adsorption of mentioned ions onto PHEMA and P(MMA-HEMA) are spontaneous and exothermic at 293–323 K.