Miscibility of poly(methoxymethyl methacrylate) and poly(methylthiomethyl methacrylate) with poly(styrene-co-acrylonitrile) and poly(p-methylstyrene-co-acrylonitrile)

The miscibility of poly(methoxymethyl methacrylate) (PMOMA) and poly(methylthiomethyl methacrylate) (PMTMA) with poly(styrene-co-acrylonitrile) (SAN) and poly(p-methylstyrene-co-acrylonitrile) (pMSAN) was studied by differential scanning calorimetry. PMOMA is miscible with SAN having an acrylonitrile (AN) content around 30 wt %. However, PMOMA is immiscible with any of the pMSAN having AN contents between 9 and 36 wt % and with pMSAN having AN contents between 19 and 34 wt %. The miscibility of the blends enables the evaluation of various segmental interaction parameters.     

Rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS)

The rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS) was investigated using a cone-and-plate rheometer. The rheological properties measured were shear stress (σ₁₂), viscosity (η), and first normal stress difference (N₁) as functions of shear rate (\documentclass{article}\pagestyle{empty}\begin{document}$ \dot \gamma$ \end{document}) in steady shearing flow, and storage modulus (G′) and loss modulus (G″) as functions of frequency (ω) in oscillatory shearing flow. It has been found that the rheological behavior of blends of ABS and PMMA was very similar to that of blends of poly(styrene-stat-acrylonitrile) (SAN) and PMMA, in that N₁ in logarithmic plots of N₁ versus σ₁₂, and G′ in logarithmic plots of G′ versus G″, vary regularly with blend composition. This has led us to conclude that the rubber particles that are grafted on an SAN resinous matrix in ABS resin plays only a minor role in influencing the compatibility of ABS/PMMA blends, and that the SAN chains attached to the surface of rubber particles, and the SAN matrix phase, play a major role in compatibilizing ABS resin with PMMA.     

Photo-Initiated Lamination of Polyethylene (PE) and Poly(ethylene terephthalate) (PET)

Besides plasma-based processes, photo-initiated surface modifications have an interesting potential for adhesion promotion. This is of special interest with applications ranging from classical finishing to composites. Photo-chemical processes using continuous UV sources — monochromatic as well as broad band — are based on radical activation and ensuing reaction with the atmosphere. Achievable effects are addition of atoms — e.g., introduction of oxygen (photo-oxidation) resulting in increased surface energy — or grafting of functional groups. Both have certain potentials for adhesion promotion in a physico-chemical way. Based on the fundamental scheme of these processes — i.e., a photon-initiated radical reaction at the substrate-atmosphere interface — a direct 'inter-linking' of coating polymer and substrate is presented in this paper. The principal idea is to apply a thin layer of coating polymer on the substrate and irradiate this composite system at certain UV wavelengths. Given a low absorption of the radiation by the thin coating and — at the same time — a high absorption by the substrate, the radiation will penetrate the coating layer and generate radicals at the interface, which will induce cross-linking between the coating polymer and substrate. It is shown that for the example of laminates of polyethylene (PE) film on fabrics made of poly(ethylene terephthalate) (PET), extremely high adhesion strenghths are achieved without any use of additional adhesion promoters.     

Victrex® poly(ethersulfone) (PES) and Victrex® poly(etheretherketone) (PEEK)

Properties of two high performance engineering thermoplastics, amorphous polyethersulfone (PES) and semicrystalline polyetheretherketone (PEEK), are discussed. Both resins can be processed by conventional techniques, compounded with high performance fibers, and have high service temperature (up to 300°C). Due to the amorphous character PES can be dissolved and spray coated into metals.     

Photooxidative stability of substituted poly(phenylene vinylene) (PPV) and poly(phenylene acetylene) (PPA)

The addition of side groups to improve the photooxidative stability of polymers used in polymer-based light-emitting diodes (LEDs) is explored. Infrared spectroscopy and computational chemistry techniques are used to study the effects of chemical substitution of the reactive vinylene moiety in poly(phenylene vinylene) (PPV). The bond order of the vinylene group in small oligomers is calculated using semiempirical techniques to assess the improvement in stability toward oxidants such as singlet oxygen. We find that PPV dimers allow relative comparisons across a range of possible substitutions. Experimental results correlate well with these calculations. The addition of electron-withdrawing substituents, such as nitrile groups, to the vinylene moiety is found to be particularly effective in reducing the reactivity of alkoxy-substituted PPV toward singlet oxygen. The photooxidative stability of a poly(phenylene acetylene) (PPA) derivative is also studied. It appears that this family of polymers is more stable toward photooxidation than are its PPV analogs. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2451–2458, 1998     

Synthesis and properties of ABA-type triblock copolymers of poly(glycolide-co-caprolactone) (A) and poly(ethylene glycol) (B)

Poly(glycolide-co-caprolactone) (A)-poly(ethylene glycol) (B) ABA-type triblock copolymers (PGCE) were synthesized by bulk ring opening polymerization, using the hydroxyl endgroups of poly(ethylene glycol) (PEG) as initiator and stannous octoate as catalyst. The resulting copolymers were characterized by various analytical techniques. Gel permeation chromatographic analysis indicated that the polymerization product was free of residual monomers, PEG and oligomers. ¹H NMR and differential scanning calorimeter results demonstrated that the copolymers had a structure of poly(glycolide-co-caprolactone) (PGC) chains chemically attached to PEG segments. All the PGCE copolymers showed improved hydrophilicity in comparison with the corresponding PGC copolymers with the same molar ratio of glycolidyl and caproyl units. The microspheres of PGCE copolymer exhibited rough surfaces quite different from the smooth surface of PGC microspheres. This phenomenon was attentively ascribed to the highly swollen ability of PGCE copolymers and the freeze-drying process in the microspheres fabrication.     

Finite strain behavior of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate)-glycol (PETG)

Uniaxial and plane strain compression experiments are conducted on amorphous poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate)-glycol (PETG) over a wide range of temperatures (25-110 °C) and strain rates (.005-1.0 s⁻¹). The stress-strain behavior of each material is presented and the results for the two materials are found to be remarkably similar over the investigated range of rates, temperatures, and strain levels. Below the glass transition temperature (θ_g=80 °C), the materials exhibit a distinct yield stress, followed by strain softening then moderate strain hardening at moderate strain levels and dramatic strain hardening at large strains. Above the glass transition temperature, the stress-strain curves exhibit the classic trends of a rubbery material during loading, albeit with a strong temperature and time dependence. Instead of a distinct yield stress, the curve transitions gradually, or rolls over, to flow. As in the sub-θ_g range, this is followed by moderate strain hardening and stiffening, and subsequent dramatic hardening. The exhibition of dramatic hardening in PETG, a copolymer of PET which does not undergo strain-induced crystallization, indicates that crystallization may not be the source of the dramatic hardening and stiffening in PET and, instead molecular orientation is the primary hardening and stiffening mechanism in both PET and PETG. Indeed, it is only in cases of deformation which result in highly uniaxial network orientation that the stress-strain behavior of PET differs significantly from that of PETG, suggesting the influence of a meso-ordered structure or crystallization in these instances. During unloading, PETG exhibits extensive elastic recovery, whereas PET exhibits relatively little recovery, suggesting that crystallization occurs (or continues to develop) after active loading ceases and unloading has commenced, locking in much of the deformation in PET.     

Thermal studies of blends of poly(phenylene sulfide) (PPS) with poly(phenylene sulfide sulfone) (PPSS) and with poly(phenylene sulfide ether) (PPSE)

The miscibilities of poly(phenylene) sulfide/poly(phenylene sulfide sulfone) (PPS/PPSS) and poly(phenylene) sulfide/poly(phenylene sulfide ether) (PPS/PPSE) blends were invesigated in terms of shifts of glass transition temperatures T_g of pure PPS, PPSS, a dn PPSE. The crystallization kinetics of PPS/PPSS blends was also studied as a function of molar composition. The PPS/PPSS and PPS/PPSE blends are respectively partially and fully miscible. PPSE shows a plasticizing effect on PPS as does PPS on PPSS, which necessarily improves te processibility in the respective systems. We can control T_g and melting temperature T_m of PPS by varying amounts of PPSE in blends. The melt crystallization temperature T_mc of PPS/PPSE blends was higher than that of the PPSE homopolymer. Therefore, these blends require shorter cycle times in processing than pure PPSE. The overall rate of crystallization for PPS/PPSS blends follows the Avrami equation with an exponent ?2. The maximal rate of crystallization for PPS/PPSS blends occurs at a temperatre higher by 10°C than that for PPS, while the crystallization half time t_1/2 is 4 times shorter. In the cold crystallization range, crystal growth rates increase and Avrami exponents decrease significantly as the temperature increases.     

New gold(I) and silver(I) complexes of sulfamethoxazole: Synthesis,X-ray structural characterization and microbiological activities of triphenylphosphine(sulfamethoxazolato-N2)gold(I) and (sulfamethoxazolato)silver(I)

Sulfamethoxazole (SMTZ) reacts with Ph₃PAuCl and AgCl in methanol/triethylamine to give [Ph₃PAu(SMTZ_-1H+)] (SMTZ_-1H+ = sulfamethoxazolato anion) (1) and [Ag(SMTZ_-1H+)] (2). While the lattice of 1 contains single molecules with linear N–Au–P bonds, compound 2 comprises a two-dimensional polymeric assembly of the deprotonated SMTZ ligand and silver ions, which are coordinated by one oxygen and three nitrogens in a distorted tetrahedral array. The microbiologic activities (Mueller–Hinton broth dilution tests) of 1 and 2 were determined in relation to free sulfamethoxazole.     

Synthesis and characterization of new poly(butadiene-co-acrylic acid(g) acrylic acid) and poly(butadiene(g) acrylic acid)

Synthetic crosslinked polymers from oligomers of butadiene-co-acrylic acid (Mw 5000) or oligomers of butadiene (Mw 6000) and acrylic acids were obtained after grafting reactions using varying reactant ratios. Characterization of the new crosslinked polymers were carried out by use of FTIR, H-NMR, and ¹³C-NMR in the solid state and also with the swollen products in D₂O, DMF D7, or DMSO D6. Determinations of swelling in distilled water for the different synthesized hydrogels showed increase in the V/Vo ratios as the concentrations of anions (carboxylate) became higher. These values were sensitive to different pH values and changes in the concentrations of electrolytes. Different behavior was observed for the polymers obtained from mass and from synthesis in benzene. SEM analysis of the surfaces of the polymers obtained in mass showed a fibrous structure (with lower contents of carboxylic groups, and more swellable and with greater capacity to retain albumin). A porous surface was observed for products obtained in benzene (with higher content of carboxyl groups and capacity to retain cations such as copper and malachite green).     

Polymerization and characterization of bis(trichlorophenolato)di(pyridine) nickel(II) and bis(tribromophenolato)di(pyridine) nickel(II) dihydrate complexes in solution in the presence of iodine

The syntheses of bis(trihalophenolato)di(pyridine) nickel(II) complexes were achieved in aqueous solution, and their characterizations were performed by Fourier transform infrared (FTIR) spectroscopy, ultraviolet‐visible analysis, differential scanning calorimetry, and elemental analysis. The thermal polymerization of these complexes was studied in toluene solution in the presence of iodine. The effect of time, temperature, and amount of iodine added on the percentage conversion, structure of polymers, and intrinsic viscosity ([η]) were investigated. Polymers were characterized by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopic analyses, glass‐transition temperatures determined by differential thermal analysis, and [η] values determined by the viscometric method. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2232–2239, 2002     

Adhesion of UV-Cured Laminates of Poly(ethylene-2,6-naphthalate) (PEN) and Poly(ethylene terephthalate) (PET) films

This paper describes the properties of an ultraviolet (UV) curable laminating adhesive system that can be used with PEN, PET and UV-stabilized PET films. The adhesive system that contains (2,4,6-trimethylbenzoyl) diphenylphosphine oxide (TPO) as photoinitiator was optimally cured with a V-bulb fitted ultraviolet irradiator. The laminated structures built with this adhesive system and PEN, PET and UV-stabilized PET films showed a large manufacturing operating window, both in terms of adhesive layer thickness, initial peel strengths above 1500 N/m, V- and D-bulb UV sources and curing speeds from 5– 10 m/min. The 600-h dry heat aging tests indicated that the UV-stabilized PET films underwent less than approximately 1% decrease in light transmission and less than a 1% gain in color. The UV-stabilized PET film and its laminate showed particularly strong retention of optical properties under damp aging and QUV weathering, compared to PEN and non-UV-stabilized PET films. Finally, the peel strengths of the laminates were retained to greater than 1300 N/m for laminate structures of 50 μm film thickness, whereas structures made from thicker films retained approx. 40–60% (700–1100 N/m) of their initial peel strength.     

Antibacterial Co(II) and Ni(II) Complexes of N-(2-Furanylmethylene)-2-Aminothiadiazole and Role of SO(4), NO(3), C(2)O(4) and CH(3)CO(2) anions on Biological Properties

Co(II) and Ni(II) complexes with a Schiff base, N-(2-furanylmethylene)-2-aminothiadiazole have been prepared and characterized by their physical, spectral and analytical data. The synthesized Schiff-bases act as tridentate ligands during the complexation reaction with Co(II) and Ni(II. metal ions. They possess the composition [M(L)(2)]X(n) (where M=Co(II) or Ni(II), L=, X=NO(3) (-), SO(4) (2-), C(2)O(4) (2-) or CH(3)CO(2) (-) and n=1 or 2) and show an octahedral geometry. In order to evaluate the effect of anions upon chelation, the Schiff-base and its complexes have been screened for antibacterial activity against bacterial strains e.g., Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa.     

HDPE、改性HDPE与PA6,6共混物的机械性能和结构形态

研究了HDPE、改性HDPE与PA6,6的共混比、制备方法及增容剂对共混物性能的影响。结果表明,改性HDPE与PA6,6共混,能够得到很好的相容性(特别是在共混比是50/50时),并在很多方面(拉伸强度、屈挠强度、伸长率)得到良好的性能;两步法得到的共混物中,HDPE与PA6,6获得良好的相容;一步法得到的共混物可得到较高的屈挠强度。     

Production and characterization of films containing poly(hydroxybutyrate) (PHB) blended with esterified alginate (ALG‐e) and poly(ethylene glycol) (PEG)

Alternative materials have long been studied and developed to replace conventional skin dressings with the emergence of new biopolymers and development of polymeric film fabrication techniques. As a new material for polymeric dressings, films of poly(hydroxybutyrate) (PHB) blended with esterified alginate (ALG‐e) and poly(ethyleneglycol) was studied. The esterification of sodium alginate (ALG‐e) generated a material with some amphiphilic characteristics and increased compatibility with the PHB. PEG was added as plasticizer in PHB/ALG‐e films was also tested, since PEG is often used in blends with PHB to improve flexibility and reduce hydrophobicity. At the amounts studied, it was found that both PEG and ALG‐e increase the degree of crystallinity, but a decrease was observed in the hydrophobic nature of PHB films. At the maximum concentration of ALG‐e and PEG used an increase in water vapor permeability and a decrease in tensile strength was reached due to the synergistic effect caused by better homogenization of PEG and ALG‐e in the PHB matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44362.     

Co(II) and Ni(II) Concentration,and Co(II) Purification with Microbiological Collectors (Saccharomyces cerevisiae)

Abstract

Co(II) and Ni(II) can be concentrated quantitatively using a microbiological collector consisting of a Saccharomyces cerevisiae strain suspended in a glucose containing phosphate buffer. Optimal conditions for such accumulation as regards pH, time, and concentration have been studied. The influence of some complexing agents on the accumulation of a mixture of Co(II) and Ni(II) has also been investigated. By adapting the Saccharomyces cerevisiae strain to Co(II), separation of Co(II) from Ni(II) in dilute solution has been achieved.     

Reduction of nitroaromatics with poly(vinylpyridine) complexes of palladium(II) and platinum(II)

Palladium(II) and platinum(II) anchored to 2- and 4-vinylpyridine polymers of different molecular weights were used for the dihydrogen reduction of various nitroaromatics and benzaldehyde in ethanol at 50°C. Palladium(II) complexes were far more effective than their platinum(II) analogues and the activity decreased with increasing molecular weights of the polymers. The nitroaromatics were selectively and almost completely reduced to the corresponding anilines. During reduction, the orange palladium(II) complexes changed to voluminous green precipitates, which could be used repeatedly and preserved for a long time without any loss of activity. A rate equation of the type: rate = K[Cat] [H₂] has been derived and a reduction mechanism has been proposed on the basis of experimental results and kinetic data.     

乙烯-乙酸乙烯酯共聚物(EVA)的性能及应用

本文综述了乙酸乙烯酯(VA)含量和熔体流动速率(MFR)对乙烯-乙酸乙烯酯共聚物(EVA)性能的影响以及EVA树脂的应用。     

双[（三氟甲基）苯并三唑]酞酸酯的合成及其缩合性能

１－羟基－６－三氟甲基苯并三唑与双酰卤化物反应，获得了三氟甲基苯并三唑双酰衍生物、双（６－三氟甲基苯并三唑）草酸酯（ＢＴＢＯ）和双（６－三氟甲基苯并三唑）邻苯二甲酸酯（ＢＴＢＰ）。其缩合试验表明是合成二肽的良好缩合剂。