Tribological behavior between micro- and nano-crystalline diamond films under dry sliding and water lubrication

The tribological behavior of micro- and nano-crystalline diamond films is evaluated in dry sliding and water lubricating condition. The main wear mechanism is found to be abrasive wear mode induced by self-polishing. Non-diamond components and higher compressive residual stresses are detected in flat MCD films after dry sliding, in comparison to NCD. Origin of decreased friction coefficient in CVD diamond tribosystems under water lubrication is attributed to the effect of water on the formed graphic material and the chemisorbing of diamond surface with H₂O, hydrogen or hydroxyl ions. For the MCD/NCD or NCD/MCD contact, the surface roughness of ball largely determines the stable friction coefficient in dry sliding, where NCD film usually presents higher wear rate.     

Tribological Performance of Diamond and Diamondlike Carbon Films at Elevated Temperatures

In this study, the authors investigated the tribological performance of diamond and diamondlike carbon (DLC) films as a function of temperature. Both films were deposited on silicon carbide (SiC) by microwave plasma chemical vapor deposition and ion-beam deposition processes. Tribological tests were performed on a reciprocating wear machine in open air (20 to 30% relative humidity) and under a 10 N load using SiC pins. For the test conditions explored, the steady-state friction coefficients of test pairs without a diamond or DLC film were 0.7 to 0.9 and the average wear rates of pins were 10^?5 to 10^?7 mm³/N·m, depending on ambient temperature. DLC films reduced the steady-slate friction coefficients of the test pairs by factors of three to five and the wear rates of pins by two to three orders of magnitude. Low friction coefficients were also obtained with the diamond films, but wear rates of the counterface pins were high due to the very abrasive nature of these films. The wear of SiC disks coated with either diamond or DLC films was virtually unmeasurable while the wear of uncoated disks was substantial. Test results showed that the DLC films could afford low friction up to about 300° C. At higher temperatures, the DLC films graphitized and were removed from the surface. The diamond films could withstand much higher tempera-lures, but their tribological behavior degraded. Raman spectroscopy and scanning electron microscopy were used to elucidate the friction and wear mechanisms of both films at high temperatures.     

Reciprocative sliding friction and wear properties of electrical discharge machined ZrO2‐based composites

Hot‐pressed, laboratory‐made, ZrO₂‐based composites with 40 vol. % WC, TiCN or TiN were surface finished by electrical discharge machining in order to compare their reciprocating sliding friction and wear response against WC–6wt%Co cemented carbide in unlubricated conditions. Sliding experiments were performed using a Plint TE77 pin‐on‐flat wear test rig, revealing a strong impact of the secondary phase on the tribological behaviour of the ZrO₂‐based composites. The worn surfaces and wear debris were characterised by scanning electron microscopy, energy dispersive X‐ray analysis and surface topography scanning, pointing out abrasion, polishing and adhesion as main wear mechanisms. The most favourable friction and wear characteristics were encountered with ZrO₂–WC composites compared to the other grades with equal amount of volumetric secondary phase. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization and tribological investigation of self-assembled lanthanum-based thin films on glass substrates

Rare-earth (RE) (lanthanum-based) thin films were prepared on hydroxylated glass substrates by a self-assembling process from specially formulated solution. Atomic force microscope (AFM) and X-ray photoelectron spectrometry (XPS) and scanning electron microscope (SEM) are used to characterize the thin films. The tribological properties of the as-prepared thin films sliding against a steel ball were evaluated on a friction and wear tester. The tribological experiment shows that the friction coefficient of glass substrate reduced from 0.85 to 0.13 after the formation of RE self-assembled film (SAM) on its surface. And the RE self-assembled film has longer wear life (2880 sliding pass). It is demonstrated that RE self-assembled film exhibited good wear resistant property. The superior friction reduction and wear life of RE films are attributed to good adhesion of the film to the substrate and special characteristic of the RE elements.     

Impact of Cr3C2/VC addition on the dry sliding friction and wear response of WC–Co cemented carbides

Two grades of WC–10 wt.%Co cemented carbide with or without addition of Cr₃C₂/VC grain growth inhibitor during liquid phase sintering were produced with the goal to investigate their reciprocating sliding friction and wear behaviour against WC–6 wt.%Co cemented carbide under unlubricated conditions. The tribological characteristics were obtained on a Plint TE77 tribometer using distinctive normal contact loads. The generated wear tracks were analyzed by scanning electron microscopy and quantified topographically using surface scanning equipment. The post-mortem obtained wear volumes were compared to the online assessed wear. Correlations between wear volume, wear rate and coefficient of friction on the one hand and sliding distance and microstructural properties on the other hand were determined, revealing a significant influence of Cr₃C₂/VC on the friction characteristics and wear performance.     

CVD diamond coated silicon nitride self-mated systems: tribological behaviour under high loads

Friction and wear behaviour of self-mated chemical vapour deposited (CVD) diamond films coating silicon nitride ceramics (Si₃N₄) were investigated in ambient atmosphere. The tribological tests were conducted in a reciprocal motion ball-on-flat type tribometer under applied normal loads up to 80 N (∼10 GPa). Several characterisation techniques—including scanning electron microscopy (SEM), atomic force microscopy (AFM) and micro-Raman studies—were used in order to assess the quality, stress state and wear resistance of the coatings. In addition, a novel method is presented to estimate the wear coefficient of the diamond coated flat specimens from AFM and optical microscopy (OM) observations of the wear tracks.     

Microstructural Characterization of Wear Particles Formed During Tribological Stressing of TiC and Ti(C,N) Coatings

An attempt was undertaken to obtain a better understanding of the tribological properties of two wear-resistant coatings on tool steel by structural and microchemical analysis of wear particles using a transmission electron microscope. Coatings were deposited by physical vapor deposition and plasma-assisted chemical vapor deposition techniques and tribological properties were derived from reciprocating sliding tests of the coatings against alumina balls. Three types of wear particles were identified by electron diffraction and energy dispersive X-ray spectroscopy: nanocrystalline rutile (TiO₂), nanocrystalline graphite and microcrystalline graphite. Low coefficients of friction, of the order of 0.2, were attributed to the formation of solid lubricant films of sub-stoichiometric TiO_2-x Magnéli phases and/or graphite.     

Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

SiO₂, TiO₂, and hydroxyapatite (HA) thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500 °C The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). Atomic force microscopy (AFM) and high-resolution scanning electron microscopy (SEM) are applied to characterize the original unworn films. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the result, the target films composed of nano-particles ranging from 30 nm to 100 nm around were obtained. All the sol–gel ceramic films are superior in resisting wear compared with the TC4 substrate. Among all, HA film shows the best resistance while SiO₂ film shows the worst wear resistance both under higher (3 N) and lower load (1 N). TiO₂ shows good wear resistance under lower load (1 N). SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro-fracture dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA film is greatly due to the slight plastic deformation of the film. It is supposed that the deformation of the HA film is closely related to the special arrangement of the nano-particles and microstructure. HA film is recommended for clinical application from the point of wear resistance view.     

Tribological behaviour of diamond coatings sliding against Al alloys

A low wear rate, combined with exceptional physical properties, makes diamond an ideal candidate for the machining of non-ferrous materials. It is particularly interesting for tooling aluminium and its alloys as it offers these soft materials clean cutting and lets the shavings slide on the tool surface.It results from studies dealing with the friction of diamond against aluminium, that the tribological behaviour of this pair is greatly influenced by the presence of oxides, more particularly Al₂O₃, on the counterface surface. It was therefore necessary to better understand the role of these oxides during the cutting process, the way they modify the nature of the contact, and their effects on transferred layer formation.The tribological behaviour of diamond coatings prepared by the combustion flame process, sliding against aluminium alloys under different environments (vacuum, oxygen and water vapour), at two applied normal loads is presented here; the modifications of both the coatings (formation of amorphous carbon) and the counterfaces (depth of the friction track), as well as the transferred layers (chemical composition, aspect) are specifically studied.The surface changes are revealed by scanning electron microscopy observations. Raman spectroscopy and energy dispersive spectroscopy analyses were realised to highlight the observed phenomena.     

Influence of Surface Finishing on the Tribological Behavior of Self-Lubricating Iron-Based Composites

Recently, we presented the tribological evaluation of self-lubricating sintered steels produced by taking advantage of the powder injection molding process, the recently introduced plasma-assisted debinding and sintering process, and the in situ formation of solid lubricant particles. This new processing route promotes the in situ generation of nanostructured turbostratic graphite particles during silicon carbide dissociation. In this work, we present the influence of surface finishing on the tribological behavior of self-lubricating composites sintered at 1150°C with (3 and 5 wt%) and without SiC additions. We discuss the effects of the surface topography (R_a) on the friction coefficient and wear rates of specimens and counterbodies. The tribological behavior was analyzed using linear reciprocating sliding tests (constant load of 7 N, 60-min duration). It was shown that the reduction in surface roughness increased both the friction coefficients and wear rates of specimens and counterbodies, probably due to plastic deformation and consequent graphite reservoir sealing. Chemical analyses of the wear scars using scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analysis showed a tribolayer that was composed predominantly of carbon and oxygen. Analyses of the wear scars showed traces of plastic deformation on both samples and counterbodies and the predominance of abrasion as the main wear mechanism.     

Tribological Properties of Phosphor Bronze and Nanocrystalline Nickel Coatings Under PAO + MoDTC and Ionic Liquid Lubricated Condition

The friction and wear properties of phosphor bronze and nanocrystalline nickel coatings were evaluated using a reciprocating ball-on-plates UMT-2MT sliding tester lubricated with ionic liquid and poly-alpha-olefin containing molybdenum dialkyl dithiocarbamate, respectively. The morphologies of the worn surfaces for the phosphor bronze and nanocrystalline nickel coatings were observed using a scanning electron microscope. The chemical states of several typical elements on the worn surfaces were examined by means of X-ray photoelectron spectroscopy. Results show that the phosphor bronze and nanocrystalline nickel coatings exhibited quite different tribological behaviors under different lubricants. Phosphor bronze plate shows higher friction coefficient (0.14) and wear rate (3.2 × 10⁻⁵ mm³/Nm) than nanocrystalline nickel coatings (average friction coefficient is 0.097, wear rate is 1.75 × 10⁻⁶ mm³/Nm) under poly-alpha-olefin containing molybdenum dialkyl dithiocarbamate lubricated conditions. The excellent tribological performance of nanocrystalline nickel coatings under above lubricant can be attributed to the formation of MoS₂ and MoO₃ on the sliding surface. a quite a number of C, O and F products on worn surface of phosphor bronze than NC nickel coatings can improve anti-wear properties while using ionic liquid as lubricant.     

Influence of secondary phases on the tribological response of electro-discharge machined zirconia-based composites against WC-Co cemented carbide

Three ceramic composite grades, consisting of a ZrO₂ matrix and 40 vol.% WC, TiC_0.5N_0.5 or TiN phase, were completely self-developed by hot pressing powder mixtures of yttria-stabilised zirconia (Y-TZP) and distinctive WC, TiC_0.5N_0.5 or TiN powder sources. The friction and wear characteristics of the zirconia-based composites against WC-Co cemented carbide were investigated by performing dry reciprocating sliding experiments on a pin-on-plate tribometer under various normal contact forces. The generated wear was quantified using surface scanning topography. Post-mortem obtained wear volumes were correlated to real-time recorded wear depth. The ZrO₂-40 vol.% WC grade displayed more favorable tribological properties compared to the other grades with equal secondary phase content. The worn surfaces and the wear debris were analysed by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX), revealing several wear mechanisms such as polishing, abrasion and wear debris layer formation, mainly depending on the imposed contact load and the material composition.     

Effect of temperature on friction and wear of prehardened tool steel during sliding against 22MnB5 steel

Abstract

Mechanical components in tribological systems exposed to elevated temperatures are gaining increased attention since more and more systems are designed to operate under extreme conditions. In hot metal forming, the effect of temperature on friction and wear is especially important since it is directly related to process economy (tool wear) and quality of the produced parts (friction between tool and workpiece). This study is therefore focused on fundamental understanding pertaining to the tribological characteristics of prehardened hot work tool steel during sliding against 22MnB5 boron steel. The tribological tests were carried out using a high temperature reciprocating sliding friction and wear tester under a normal load of 31 N (corresponding to a contact pressure of 10 MPa), a sliding speed of 0·2 m s^?1 and temperatures ranging from 40°C to 800°C. It was found that friction coefficient and specific wear rate decreased at elevated temperature because of formation of compacted wear debris layers on the surfaces.     

Sliding tribological behavior of AlCrN coating

The sliding tribological behavior of the PVD AlCrN coating against Si₃N₄ ball have been investigated by using the CETR multi-functional UMT-2 test system under two sliding conditions (bidirectional and unidirectional). Reciprocating sliding tests (bidirectional) were performed under varied normal loads (5, 10 and 20 N) at sliding velocity of 0.48 m/min. Ball-on-disc tests (unidirectional) were performed at varied sliding velocities (0.48 and 5 m/min) under normal load of 5 N. The wear scars of the coating were evaluated by surface profilometer, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), and the sliding wear mechanism of the coating was consequently discussed. The results showed that AlCrN coating had excellent anti-abrasion properties. Both the normal load in reciprocating sliding test and the sliding velocity in ball-on-disc test had significant influence on the sliding tribological behavior of the AlCrN coating. The combination of abrasion and oxidation was the main sliding wear mechanism for the AlCrN coating. The wear resistant and thermally stable oxides formed by the tribo-chemical reactions of chromium and aluminum protected the AlCrN coating against wear admirably.     

Tribological properties of lubricated nanocrystalline diamond surfaces for various loads and geometries

Abstract

Diamond and diamond-like carbon films are well known for their outstanding properties such as high hardness, low coefficient of friction, good thermal conductivity, excellent biocompatibility and electrical insulation. Diamond films with nanocrystalline grains offer added advantages of higher hardness, improved surface finish (less roughness), very high sp³ content, etc. In view of the above, the present investigation is undertaken to explore the possibility of using nanocrystalline diamond films in advanced tribological applications. In this work, a nanocrystalline diamond film is deposited using a unique chemical vapour deposition (CVD) technique. The microstructural features are characterised using atomic force microscopy (AFM). Tribological behaviour of these films is evaluated by means of a reciprocating model tribometer with various lubricants. The worn surfaces are examined using three-dimensional confocal microscopy. The results show that these films have comparable friction coefficient with and without lubricants. Furthermore, they exhibited negligible wear for the tested range of loads.     

Dry reciprocating wear of Al-Si-SiCp composites: A statistical analysis

In this paper, effect of various wear test and material related parameters (applied load, sliding distance, reciprocating velocity, counter surface temperature and weight percentage of silicon) on dry wear behavior of two Al-Si-SiC_p composites under reciprocating conditions was studied using fractional factorial design. Developed mathematical model showed that Al-Si-SiC_p with high silicon content composite is subjected to a lower wear compared to that of low silicon composite. The applied load, sliding distance, reciprocating velocity and percentage silicon weight in composite are the four important and controlling factors; counter surface temperature has a minor effect on the wear of the composite specimens in dry condition.     

Ionic Liquid Lubrication Effects on Ceramics in a Water Environment

Ionic liquids were studied to determine their effectiveness as boundary lubricant additives for water. The chemical and tribochemical reactions that govern their behavior were probed to understand lubrication mechanisms. Under water lubricated conditions, silicon nitride ceramics are characterized by a running-in period of high friction, during which time the surface is modified causing a dramatic decrease in friction and wear. Two mechanisms have been proposed to explain the friction and wear behavior. Si₃N₄ sliding against itself may result in tribochemical reactions that form a hydrated silicon oxide layer on the surface of the sliding contact. This film has been suggested to mediate friction and wear. Others have suggested that tribo-dissolution of SiO₂ results in an ultra smooth surface and after a running-in period of high wear, the lubrication mode becomes hydrodynamic. The goal of this study was to examine the effects that ionic liquids have on the friction and wear properties of Si₃N₄, in particular their effects on the running-in period. Tribological properties were evaluated using pin-on-disk and reciprocating tribometers. The tribological conditions of the tests were selected to produce mixed/hydrodynamic lubrication. The relative lubrication mode between mixed and hydrodynamic was controlled by the initial surface roughness. Solutions containing 2 wt% ionic liquids were produced for testing purposes. Chemical analysis of the sliding surfaces was accomplished with X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The test specimens were 1 in diameter Si₃N₄ disks sliding against 1/4 in Si₃N₄ balls. The addition of ionic liquids to water resulted in dramatically reduced running-in periods for silicon nitride from thousands to the hundreds of cycles. Proposed mechanisms include the formation of BF_x and PF_x films on the surface and creation of an electric double layer of ionic liquid.     

Characterization and mechanical/tribological properties of nano Au-TiO2 composite thin films prepared by a sol-gel process

Nano Au-TiO₂ composite thin films on Si(1 0 0) and glass substrates were successfully prepared with a facile sol-gel process followed by sintering. The morphology and mircostructure of the films were investigated via X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and scanning electron microscopy (SEM). The Au particles, of diameter 14-22 nm depending on the sintering temperatures used, were found to be well dispersed in the TiO₂ matrix, with a small amount of the particles escaped from the film. The surfaces of the films were uniform, compact and crack-free. Hardness and elastic modulus of the films were measured by using the nanoindentation technique. Friction and wear properties were investigated by using a one-way reciprocating tribometer. It was found that the highest hardness and elastic modulus values were obtained for the films prepared with 500 °C sintering temperature. The films displayed superior antiwear and friction reduction performances in sliding against an AISI 52100 steel ball. With 5.0 mol% Au, the friction coefficient was only 0.09-0.10 and the wear life was more than 2000 sliding cycles. The friction coefficient and wear life decreased with increasing sliding speed and load. The failure mechanism of the Au-TiO₂ films was identified to be light scuffing and abrasion. Those films can be potentially applied as ultra-thin lubricating coatings.     

Particulate Matter Generation Properties from Sliding Parts Made of Various Carbonaceous Films

The purpose of this work is to reduce the particulate matter (PM) generation from sliding parts by applying carbonaceous films. We investigate particle generation properties of wear-resistant carbonaceous films in the form of a particle size distribution chart. Using a laser scattering type particle counter, we evaluated the particle generation properties of sliding parts coated with high crystallinity, N⁺-implanted high-crystallinity and low-crystallinity diamond films, diamond-like carbon films deposited by ion beam enhanced deposition using static and dynamic mixing methods, Si₃N₄ silicon nitride, and SUS340C stainless steel. The diamond films showed significantly lower particle generation, especially for large particles, than DLC, Si₃N₄, and SUS340C films owing to lower wear. Particle generation from N⁺-implanted diamond films was greater for small particles than for the other diamond films owing to the wear of the N⁺-implanted layer.     

Microstructure and Tribological Properties of a HfB<Subscript>2</Subscript>-Containing Ni-Based Composite Coating Produced on a Pure Ti Substrate by Laser Cladding

A HfB₂-containing Ni-based composite coating was fabricated on Ti substrates by laser cladding, and its microstructure and tribological properties were evaluated during sliding against an AISI-52100 steel ball at different normal loads and sliding speeds. The morphologies of the worn surfaces were analyzed by scanning electron microscopy (SEM) and three-dimensional non-contact surface mapping. The results show that wear resistance of the pure Ti substrate and NiCrBSi coating greatly increased after laser cladding of the HfB₂-containing composite coating due to the formation of hard phases in the composite coating. The pure Ti substrate sliding against the AISI-52100 counterpart ball at room temperature displayed predominantly adhesive wear, abrasive wear, and severe plastic deformation, while the HfB₂-containing composite coating showed only mild abrasive wear and adhesive wear under the same conditions.