Surface organic modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.     

Formation of bulk ferromagnetic nanostructured Fe<Subscript>40</Subscript>Ni<Subscript>40</Subscript>P<Subscript>14</Subscript>B<Subscript>6</Subscript> alloys by metastable liquid spinodal decomposition

Nanostructured Fe₄₀Ni₄₀P₁₄B₆ alloy ingots of 3–5 mm in diameter could be synthesized by a metastable liquid state spinodal decomposition method. For undercooling ΔT > 260 K, the microstructure of the undercooled specimen had exhibited liquid state spinodal decomposition in the undercooled liquid state. The microstructure could be described as two intertwining networks with small grains dispersed in them. For undercooling ΔT > 290 K, the overall microstructure of the specimen changed into a granular morphology. The average grain sizes of the small and large grains are ≅ 30 nm and ≅ 80 nm, respectively. These prepared samples are soft magnets with saturation magnetization B _s ≅ 0.744 T. Supported by the Hong Kong Research Grants Council the National Natural Science Foundation of China (Grant No. 50861007) and Xinjiang University Doctoral Research Start-up Grant (Grant No. BS050102)     

Influences of dopants on microstructure and magnetic properties of (Mg<Subscript>0.476</Subscript>Mn<Subscript>0.448</Subscript>Zn<Subscript>0.007</Subscript>)(Fe<Subscript>1.997</Subscript>Ti<Subscript>0.002</Subscript>)O<Subscript>4</Subscript> ferrites

Influences of addition of CaO, CoO and V2O5 on the microstructure and magnetic properties of (Mg0.476Mn0.448Zn0.007)(Fe1.997Ti0.002)O4 ferrites were investigated. The powders of (Mg0.476Mn0.448Zn0.007) (Fe1.997Ti0.002)O4 composition were prepared by using a conventional ceramic powder processing technique. The experimental results showed that the average grain size of the sintered ferrites codoped with 0.03wt% CaO, 0.04wt% CoO and 0.06wt% V2O5 was about 15 μm; the saturation magnetization of ferrites was 68.78 emu/g. The addition of V2O5 in the ferrites can not only increase value of the saturation magnetization, but also decrease the average grain size of (Mg0.476Mn0.448Zn0.007)(Fe1.997Ti0.002)O4 ferrites. Simultaneous incorporation of CoO, CaO and V2O5 dopants into (Mg0.476Mn0.448Zn0.007)(Fe1.997Ti0.002)O4 ferrites can not only improve the saturation magnetization of the materials, but also inhibit abnormal grain growth.     

Synthesis and characterization of (PEO)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>−(V<Subscript>0.85</Subscript>Mo<Subscript>0.15</Subscript>)<Subscript>2</Subscript>O<Subscript>5</Subscript> nanocomposite films

(PEO) _x −(V_0.85Mo_0.15)₂O₅(x=0,0.5,1.0) nanocomposite films were prepared by a modified sol-gel method. The structure of the films was analyzed by XRD, and the DC electrical conductivity. Cyclic voltammogram and optical spectral transmittance were investigated. The results show that the (V_0.85Mo_0.15)₂O₅ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1.7897 nm at x=1.0. The introduction of MoO₃ improved the DC electrical conductivities of the films due to the generation of V₄₊ to maintain the electrical neutrality of the oxides. PEO intercalated in the interlayer of (V_0.85Mo_0.15)₂O₅ oxides has interaction with the oxides, enhancing the amount of Li⁺ ions inserted into the interlayer of the oxides. Moreover, the intercalation of PEO into the interlayer of (V_0.85Mo_0.15)₂O₅ oxides improved the cathodic electrochromic property in near ultraviolet region and anodic electrochromic property in visible range. JIANG Cong-sheng: Born in 1963 Supported by the Science Foundation of Hubei Province (Grant No. 2001ABB083)     

Modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles by L-dopa or dopamine as an enzyme support

Fe3O4 magnetic nanoparticles were prepared by co-precipitation of Fe^2＋ and Fe^3＋ in an ammonia solution, and its size was about 36 nm measured by an atomic force microscope. Fe3O4 magnetic nanoparticles were modified by L-dopa or dopamine using sonication method. The analysis of FTIR clearly indicated the formation of Fe-O-C bond. Direct immobilization of trypsin （EC： 3.4.21.4） on Fe3O4 magnetic nanoparticles with L-dopa and dopamine spacer was investigated using glutaraldehyde as a coupling agent. No significant changes in the size and magnetic property of the three kinds of magnetic nanoparticles linked with or without trypsin were observed. The existence of the spacer molecule on magnetic nanoparticles could greatly improve the activity and the storage stability of bound trypsin through increasing the flexibility of enzyme and changing the microenvironment on nanoparticles surface compared to the naked magnetic nanoparticles.     

Self-Propagating High-Temperature Reduetive Synthesis of TiB2-Al2O3 Composite Powders

TiB2-Al2O3 composite powders were produced by self-propagating high-temperature synthesis（SHS） method with reductive process from B2O3-TiO2-AI system. X-ray diffraction（XRD） and scanning electron microscopy（SEM） analyses show the presence of TiB2 and Al2O3 only in the composite powders produced by SHS. The powders are uniform and free-agglomerate. Transmission electron microscopy （TEM） and high resolution electron microscopy （HREM） observation of microstructure of the composite powders indicate that the interfaces of the TiB2-Al2O3 bond well, without any interfacial reaction products. It is proposed that the good interfacial bonding of the composite powders can be resulted from the TiB2 particles crystallizing and growing on the Al2O3 particles surface with surface defects acting as nucleation centers.     

Domain structure and defects of highly ordered Bi<Subscript>4</Subscript>Si<Subscript>3</Subscript>O<Subscript>12</Subscript> micro-crystals

Highly ordered Bi₄Si₃O₁₂ micro-crystals were prepared at normal atmosphere. Phase identification of the prepared crystals was accomplished by X-ray diffractometer (XRD). Domain structure and defects were characterized by environmental scanning electron microscopy (ESEM). XRD shows that the obtained micro-crystals are of eulytite structure with chemical formulation of Bi₄Si₃O₁₂. A highly ordered growth pattern is confirmed due to the faster growth of the {124} faces than that of the {204} faces by ESEM. The growing process of the domain structure is of pollen parent and filial generation pattern. The filial generations of Bi₄Si₃O₁₂ crystals are generated from the pollen parent. Cracks generate from the defect areas and propagate along the {124} faces due to their lower binding energy under a proper temperature gradient, contributing to the total transcrystalline fracture. It is confirmed that the generation and development of the voids in the crystal grains can be developed when unmatched dimensions of the two opposite faces are formed. And the development of the voids is dependent on the dimensions and orientations of the two opposite faces. Supported by the Innovation Research Team Funds of Shaanxi University of Science & Technology (Grant No. SUST-A04)     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> content on residual stress and properties of CAS glass-ceramics

The structure and properties of the glass-ceramics were tested with X-ray diffraction testing instrument,correlative software,and other modern testing means.Then the effect of Al2O3 content on internal stresses in CaO-Al2O3-SiO2 glass-ceramics was studied deeply.In order to study the relationship of Al2O3 to the residual stress of CaO-Al2O3-SiO2 glass-ceramics,X-ray diffraction ＂sin2ψ＂ was used.The means utilized the x radial incidence produced from cathode radial tube,and took the space between crystals as measurement of strain.When the stresses produced,the space between crystals changed and the diffraction peak moved during Bragg diffraction.The magnitude of movement is related to the stresses.The experimental results show the residual stress is considerably high and Al2O3 can influence the mechanical properties of this material hugely.     

Synthesis and characterization of a new Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> pillared triple-layered perovskite KSr<Subscript>2</Subscript>Nb<Subscript>3</Subscript>O<Subscript>10</Subscript>

A n-Hexyl NH₃Sr₂Nb₃O₁₀ is obtained by the stepwise ion-exchange reaction, then is dispersed in aqueous solution of trinuclear acetato-hydroxo iron (III) nitrate, [Fe₃(OCOCH₃)₇OH·2H₂O]NO₃, and the interlayer potassium cations of the perovskite niobate are exchanged with the partially hydrolyzed trinuclear acetato complex ions. On heating, the exchanged complex ions are converted into iron oxide pillars which keep the perovskite sheets apart. The product is characterized by XRD, SEM, EDAX and surface area measurement respectively. Zhang Hui: Born in 1970 Funded by the National Natural Science Foundation of China (No. 50002007), Major Program of Ministry of Education (No. 0201) and Open Foundation of State Key Lab of Advanced Tech. for Materials Synthesis and Processing.     

Effect of La doping on microstructure and ferroelectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films prepared by sol-gel method

The Bi4Ti3Oi2 and Bi3.25La0.75Ti3O12 thin films were prepared on the Pt/Ti/SiO2/Si substrate using the sol-gel method. The effect of La doping on the microstructure and ferroelectric properties of Bi4Ti3O12 films were investigated. Both the Bi4Ti3O12 and Bi3.25La0.75Ti3O12 thin films exhibited typical bismuth layered perovskite structure. The 2Pr （remanent polarization） value of Bi3.25La0.75Ti3O12 thin films is 18.6 μC/cm^2, which is much larger than that of Bi4Ti3O12 thin films. And the Bi3.2eLa0.75Ti3O12 films show fatigue-free behavior, while the Bi4Ti3O12 thin films exhibit the fatigue problem. The mechanism of improvement of La doping was discussed.     

Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> thin films prepared by sulfurizing different multilayer metal precursors

Cu₂ZnSnS₄ (CZTS) thin films were successfully fabricated on glass substrates by sulfurizing Cu-Sn-Zn multilayer precursors, which were deposited by ion beam sputtering and RF magnetron sputtering, respectively. The structural, electrical and optical properties of the prepared films under various processing conditions were investigated in detail. Results showed that the as-deposited CZTS thin films with the precursors by both ion beam sputtering and RF magnetron sputtering have a composition near stoichiometric. The crystallization of the samples, however, has a strong dependence on the atomic percent of constituents of the prepared CZTS films. A single phase stannite-type structure CZTS with a large absorption coefficient of 10₄/cm in the visible range could be obtained after sulfurization at 520°C for 2 h. The samples relative to the RF magnetron sputtering showed a low resistivity of 0.073 Ωcm and band gap energy of about 1.53 eV. The samples relative to the ion beam sputtering exhibited a resistivity of 0.36 Ωcm and the band gap energy is about 1.51 eV. Supported by the National Natural Science Foundation of China (Grant No. 10574106), the Planned Science and Technology Project of Guangdong Province (Grant No.2003C05005) and the Natural Science Fund of Zhanjiang Normal University (Grant No.200801)     

High-temperature oxidation behavior of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl matrix composite in air

The oxidation behavior of Al₂O₃/TiAl in situ composites fabricated by hot-pressing technology was investigated at 900° in static air. The results indicate that the mass gains of the composites samples decrease gradually with increasing Nb₂O₅ content and the inert Al₂O₃ dispersoids effectively increase the oxidation resistance of the composites. The higher the Al₂O₃ dispersoids content, the more pronounced the effect. The primary oxidation precesses obey approximately the linear laws, and the cyclic oxidation precesses follow the parabolic laws. The oxidized sample containing Ti₂AlN and TiAl phases in the scales exhibits excellent oxidation resistance. The oxide scale formed after exposure at 900°C for 120 h is multiple-layered, consisting mainly of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner TiO₂+Al₂O₃ mixed layer. From the outer layer to the inner layer, TiO₂+Al₂O₃ mixed layer presents the transit of Al-rich oxide to Ti-rich oxide mixed layer. Near the substrate, cross-section micrograph shows a relatively loose layer, and micro- and macro-pores remain on this layer, which is a transition layer and transferres from Al₂O₃+TiO₂ scale to substrate. The thickness of oxide layer is about 20 μm. It is also found that continuous protective alumina scales can not be observed on the surface of oxidation scales. Ti ions diffuse outwardly to form the outer TiO₂ layer, while oxygen ions transport inwardly to form the inner TiO₂+Al₂O₃ mixed layer. Under long-time intensive oxidation exposure, the internal Al₂O₃ scale has a good adhesiveness with the outer TiO₂ scale. No obvious spallation of the oxide scales occurs. The increased oxidation resistance by the presence of in situ Al₂O₃ particulates is attributed to the enhanced alumina-forming tendency and thin and dense scale formation. Al₂O₃ particulates enhance the potential barrier of Ti ions from M/MO interface to O/MO interface, thereby the TiO₂ growth rate decreases, which is also beneficial to improve the oxidation resistance. Moreover, the multi-structure of the TiO₂+Al₂O₃ mixed layer decreases the indiffusion of oxygen ions and also avails to improve the high temperature oxidation resistance of the as-sintered composites. Supported by the Special Program for Education Bureau of Shaanxi Province, China (Grant No. 08JK240) and Scientific Research Startup Program for Introduced Talents of Shaanxi University of Technology, China (Grant No. SLGQD0751)     

Synthesis of polyaniline-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocomposites and their conductivity and magnetic properties

By using inorganic Fe₃O₄ nanoparticles of different content as nucleation sites, PAn-Fe₃O₄ nanorods were successfully synthesized through a simple, conventional, and inexpensive one-step in-situ polymerization method. The TEM images revealed the size and morphology of the resultant nanocomposite. The EDS pattern confirmed the existence of Fe₃O₄ in the composite. The FT-IR spectral analysis confirmed the formation of PAn encapsulated Fe₃O₄ nanocomposite. With the content of Fe₃O₄ increasing, the conductivity of the nanocomposites gradually decreases, meanwhile, the saturation magnetization increases and reveals a super paramagnetic behavior. With controllable electrical, magnetic, and electromagnetic properties, the well-prepared nanocomposites may have the potential applications in chemical sensors, catalysis, microwave absorbing, and electro-magneto-rheological fluids, etc.     

Dielectric tunable properties of BaTi<Subscript>4</Subscript>O<Subscript>9</Subscript>-doped Ba<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>TiO<Subscript>3</Subscript> microwave composite ceramics

BaTi₄O₉-doped Ba_0.6Sr_0.4TiO₃ (BST) composite ceramics were prepared by the conventional solid-state reaction and their structure, dielectric nonlinear characteristics and microwave dielectric properties were investigated. The secondary phase of the orthorhombic structure Ba₄Ti₁₃O₃₀ is formed among BST composite ceramics with the increase of BaTi₄O₉. At the same time, a duplex or bimodal grains size distribution shows fine grains in a coarse grain matrix. The degree of frequency dispersion of dielectric permittivity below T _m is increased initially and then decreased with respect to BaTi₄O₉. As the BaTi₄O₉ content increases, the tunability of composite ceramics decreases, while the Q value increases. Interestingly, 70 wt% BaTi₄O₉-doped BST has a tunability ∼4.0% (under 30 kV/cm biasing) versus a permittivity ∼68 and quality factor ∼134.1 (at ∼3.2 GHz). Supported by the Ministry of Science and Technology of China through 973-project (Grant No. 2009CB623302), the Cultivation Fund of the Key Scientific and Technical Innovation Project, Ministry of Education of China (Grant No.707024), Shanghai Committee of Science and Technology (Grant No. 07DZ22302), and Shanghai Foundation Project under 06JC14070     

Optical and magnetic properties of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nano-composite films

Fe₂O₃/SiO₂ nano-composite films were prepared by sol-gel technique combining heat treatment in the range of 100–900 °C. The particle size was observed by FE-SEM. Optical properties of the films were investigated by UV-visible spectra. Structural and magnetic characteristics were investigated through FT-IR and VSM. The transparency of the Fe₂O₃/SiO₂ nano-composite films decreased with the content of the Fe₂O₃. Water and organic solvent in the films were evaporated with heat treatment, so the transparency of the films was enhanced under high temperature. It is also found that the saturation magnetization (M _s) of the films increases with the temperature. As the content of the Fe₂O₃ increases, when the content of the Fe₂O₃ is around 30wt%, the M _s of the films has a maximum value.     

The film-forming behavior on the interface between air and hydrosol of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

The film forming behavior on the interface between air and hydrosol of Fe₂O₃ nanoparticles was investigated by the surface pressure-time isotherms, the surface pressure-trough area isotherms, Brewster angle microscopy and transmission electron microscopy. It is found that the freshly prepared hydrosol of Fe₂O₃ nanoparticles is not stable. The surface pressure increases with the aging time and finally approaches a constant, and the smaller the concentration is, the smaller the surface pressure is stabilized at and the shorter the time the hydrosol reaching stable needs. The surface pressure also increases with compression until collapsed, and the longer the hydrosol is aged, the higher the collapsing pressure is. A uniform and compact film composed of nanoparticles with an average diameter of about 2–3 nm on the air-hydrosol interface is observed by Brewster angle microscope and transmission electron microscope. Funded by the National Natural Science Foundation of China (50672089), the Encouraging Foundation for the Scientific Research of the Excellent Young and Middleaged Scientists in Shandong Province(2006BS04034)     

Dielectric Properties of B2O3 Doped MgTiO3-CaTiO3 System Ceramics

The dielectric ceramics with a main crystal phase of MGTiO3 and additional crystal phase of CaTiO3 were prepared by the conventional electronic ceramics technology .the strucures of MgTiO3 are ilmenitetype,and belong to hexagonal syngony.the ratio of MgTiO3 to Ca TiO3 doping on the dielectric properties of MGTiO3-CaTiO3(MCT)ceranics were inrestigated.the addition of B2O3 decreases the sintering temperatnre and results in rapid desification without obrious negative effect on the Q values of the system(Q=1/tan ).B2O3 exists as liquid phase in the sintering process,promoting the reactions as a singering agent.     

Preparation and ferroelectric properties of Bi<Subscript>3.4</Subscript>Ce<Subscript>0.6</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films grown by sol-gel method

We have investigated the preparation and properties of Bi_3.4Ce_0.6Ti₃O₁₂ thin films. The Bi_3.4Ce_0.6Ti₃O₁₂ thin films were fabricated on the Pt/Ti/SiO₂/Si substrates using sol-gel method. The structure and morphology of the films were characterized using X-ray diffraction and atomic force microscopy. The thin films showed a perovskite phase and dense microstructure. The dielectric constant and the dissipation factor of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were about 172 and 0.031 at 1 kHz, respectively. The 2P _r and 2E _c of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were 67.1 μC/cm² and 299.7 kV/cm, respectively, under an applied field of 600 kV/cm. The Bi_3.4Ce_0.6Ti₃O₁₂ film did not show fatigue up to 4.46×10⁹ switching cycles at a frequency of 1 MHz, and showed good insulating behavior according to the test of leakage current. Supported by the Natural Science Foundation of Hubei Province (Grants No. 2004ABA082)     

Microstructures and mechanism of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al composites fabricated by the reaction between SiO<Subscript>2</Subscript> and molten aluminum

Al₂ O₃/Al composite was fabricated by the reaction between SiO₂ and molten aluminum. The microstructures of the composite obtained under different reaction conditions were analyzed. The formation mechanism of the composite microstructure was discussed. Results show that the reaction kinetics is influenced remarkably by the reaction temperature, reaction time and the quantity of SiO₂. The morphologies of Al₂O₃ have different features, depending on the reaction temperature. The composite has equaxed Al₂O₃ grains when materials reacted below 1200°C, and the composite is composed of a large number of fine Al₂O₃ grains and aluninum. The composite has a frame-shaped Al₂O₃ microstructure at the reaction temperature of above 1250°C. CHENG Xiao-min: Born in 1964 Funded by the National Natural Science Foundation of China (No. 91522)     

Incrusting structure of nanosized Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> particles in magnetic fluids

High-performance nanosized Fe₃O₄ magnetic fluids are prepared by chemical co-precipitate method. The microstructure of magnetic fluids is characterized using a transmission electron microscope (TEM) and high-resolution microscope (HREM). The results are satisfactory. The nanosized magnetic particles have diameter of 8–10 nm and the minimum diameter is 4 nm, belonging to super-paramagnetic material. The nanosized magnetic particles crystallized completely and have clear crystal boundary. The surfactant used in the test coats the magnetic particles homogeneously and forms a uniform and complete elastic spherical shell of amorphous phase around the magnetic particles. The study proves that the incrusting layer of surfactant has the protective effect and stable effect on the magnetic particles. These effects can enhance and maintain the magnetic properties of the magnetic fluids effectively.