冷变形对12Cr铁素体/马氏体钢回复与再结晶过程的影响

研究了一种新型高Cr低活性铁素体/马氏体(F/M)钢用作超临界水堆燃料包壳管用候选材料,研究冷变形对其铁素体和板条马氏体双相组织的回复、再结晶过程的影响.结果表明,不同冷变形量对板条马氏体再结晶的促进程度不同,10%冷变形后780℃高温退火只发生回复,回火马氏体板条发生合并与迁移;60%冷变形后780℃高温退火,回火马...     

LOW-CYCLE FATIGUE INVESTIGATIONS AND NUMERICAL SIMULATIONS ON DUAL PHASE STEEL WITH DIFFERENT MICROSTRUCTURES

Abstract— Fully reversed low cycle fatigue tests were carried out on 7 mm diameter cylindrical specimens of a dual phase steel treated to give five different microstructures, namely F—ferrite (+ little carbide particles), CF—continuous ferrite + 8.2% martensite, FM—49.1% ferrite + 50.9% martensite mixed structure, CM—continuous martensite + 22.4% ferrite and M—100% martensite. A finite element program was developed based on Eisenberg's cyclic plasticity theory and the low cycle stress-strain response of the steels with duplex phase microstructures was calculated from the low cyclic curves of the single ferrite (steel F) and martensite (steel M) phase. The experimental results show that fatigue performance of dual phase steel improves as martensite content is increased up to about 50%, thereafter it obviously deteriorates. During cyclic loading, the calculated plastic strain accumulated in ferrite is higher than that in martensite. Inhomogeneity of the plastic strain accumulation in steel CF is more pronounced than that in steel CM. In steel FM a relatively uniform strain distribution was found. Controlling the size of particle phase can result in an optimum strain distribution. Thus, the plastic deformation capability of the constituent phases can be enhanced leading to fatigue performance improvement. Crack initiation occurs easily at the ferrite/martensite interface with a coarse particle phase size, regardless of phase continuity. In steel CF, a crack initiates at the interface perpendicular to the stress axis and propagates in the ferrite matrix by deflecting around coarse martensite particles or by cutting fine martensite particles. In steel CM, a crack initiates at the interface along the stress axis and propagates in the martensite matrix through ferrite particles.     

Studies on the stress-strain relations of dual-phase steels

The correlations of the work-hardening exponent,n, with quenching temperature, martensite volume-fraction (MVF) and solute concentration in ferrite are discussed and derived for dual-phase steel. The flow stress of dual-phase steel at low strain is suggested to be expressed by the combination of the terms due to plastic deformation in ferrite and elastic deformation of martensite. Previous experimental results are compared with the behaviour suggested by this theoretical work. In addition, an expression for the work hardening exponents at moderate strains and at the onset of necking are also theoretically suggested.     

Effects of microstructural variables on the deformation behaviour of dual-phase steel

An expression for the stress of martensite in dual-phase steel was developed, which shows the interdependence of the stress of martensite and strain hardening in the ferrite matrix and the contribution of microstructural variables (the volume fraction of martensite f_m, ferrite grain size d_f, and martensite particle size d_m). The onset of plastic deformation of martensite in dual-phase steel was predicted to depend on its yield strength and the microstructural variables, and this was verified by the modified Crussard-Jaoul analysis. It was found that for this dual-phase steel, refining the grain size and increasing f_m increase the flow stress and raise the strain hardening rate at low strains, but little affect the strain hardening rate at high strains. The effect of the ferrite grain size on the flow stress of this dual-phase steel was found to obey the Hall-Petch relation, i.e. σ = σ₀^e + K^ed_f^−1/2, where the Hall-Petch intersection σ₀^e and slope K^e are functions of strain, f_m and d_m. The effects of the plastic deformation of martensite and the microstructural variables on the strain hardening rate and the Hall-Petch behaviour were analysed in terms of the densities of statistically stored dislocations and geometrically necessary dislocations using the previously developed theoretical model.     

Real microstructure based micromechanical model to simulate microstructural level deformation behavior and failure initiation in DP 590 steel

Dual phase (DP) steels having a microstructure consists of a ferrite matrix, in which particles of martensite are dispersed, have received a great deal of attention due to their useful combination of high strength, high work hardening rate and ductility. In the present work, a microstructure based micromechanical model is developed to capture the deformation behavior, plastic strain localization and plastic instability of DP 590 steel. A microstructure based approach by means of representative volume element (RVE) is employed for this purpose. Dislocation based model is implemented to predict the flow behavior of the single phases. Plastic strain localization which arises due to incompatible deformation between the hard martensite and soft ferrite phases is predicted for DP 590 steel. Different failure modes arise from plastic strain localization in DP 590 steel are investigated on the actual microstructure by finite element method.     

Mechanical properties of ultrafine grained ferritic steel sheets fabricated by rolling and annealing of duplex microstructure

A new route to fabricate ultrafine grained (UFG) ferritic steel sheets without severe plastic deformation is proposed in this article. A low-carbon steel sheet with a duplex microstructure composed of ferrite and martensite was cold-rolled to a reduction of 91% in thickness, and then annealed at 620–700 °C. The microstructure obtained through the process with annealing temperatures below 700 °C was the UFG ferrite including fine cementite particles homogenously dispersed. The grain size of ferrite matrix changed from 0.49 to 1.0 μm depending on the annealing temperature. Dynamic tensile properties of the produced UFG steels were investigated. The obtained UFG ferrite–cementite steels without martensite phase showed high strain rate sensitivity in flow stress. The UFG ferritic steels are expected to have high potential to absorb crash energy when applied to automobile body.     

Role of microstructure and testing conditions in sulphide stress cracking of X52 and X60 API steels

The resistance of X52 and X60 API steels to sulphide stress cracking (SSC) was tested by tensile tests at a constant load and also by slow strain rate tensile (SSRT) tests. Both steels were tested after hot-rolling, when they had a microstructure which consisted predominantly of ferrite and pearlite. They were then tested after laboratory quenching and tempering, when their microstructure was predominantly of tempered bainite or martensite. The results showed that the resistance of the steel to SSC depended strongly on the microstructure when it was tested under a constant load. In this case, the quenching and tempering considerably increased the resistance of the steel to SSC. The results of SSRT tests were similar regardless of the heat treatment used. Non-metallic inclusions seemed to play an important role as crack initiation sites during the SSRT tests; this may be due to the hydrogen–deformation interaction. The resistance to SSC varied as a function of the specimen's orientation during the SSRT tests. This may be related to the geometric characteristics of the non-metallic inclusions.     

Effects of ferrite grain size and martensite volume fraction on dynamic deformation behaviour of 0·15C–2·0Mn–0·2Si dual phase steels

Abstract

Effects of ferrite grain size and martensite volume fraction on quasistatic and dynamic deformation behaviour of 0·15C–2·0Mn–0·2Si dual phase steels were investigated in this study. Dynamic torsional tests were conducted on six steel specimens that had different ferrite grain sizes and martensite volume fractions, using a torsional Kolsky bar, and then the test data were compared in terms of microstructures, tensile properties, fracture mode, and adiabatic shear band formation. Under dynamic torsional loading, maximum shear stress and fracture shear strain increased with decreasing ferrite grain size and increasing martensite volume fraction. Observation of the deformed area beneath the fracture surface after the dynamic torsional test indicated that adiabatic shear bands of 5 to 15 μm in width were formed along the shear stress direction, and that voids or microcracks initiated at ferrites or martensite/ferrite interfaces below the shear band. The width of the shear band decreased as the ferrite grain size increased or the martensite volume fraction decreased. These phenomena were then analysed by introducing concepts of theoretical critical shear strain.     

Effect of martensite content,its dispersion,and epitaxial ferrite content on Bauschinger behaviour of dual phase steel

Abstract

Dual phase microstructures were produced in a low carbon steel, in which the martensite volume fraction was kept constant at two levels, of 18 and 25%, while the epitaxial ferrite content was varied independently. The microstructures were produced with two dispersions of martensite, a relatively coarse dispersion by intercritical annealing of a ferrite/pearlite starting microstructure and a finer dispersion from an initial martensitic microstructure. Bauschinger tests were conducted using prestrains in both tension and compression of 0.4, 1, and 2.2%. Prestrain direction had no measurable effect on plastic flow behaviour after strain reversal. Mean back stresses increased with increasing strain and martensite content, and were higher for the finer martensite dispersion. They decreased significantly with increasing epitaxial ferrite content in the case of the finer dispersion, but less significantly in the coarser dispersion. These effects of microstructure are discussed in terms of stress transfer to martensite, work hardening, and tensile properties. It is concluded that about half of the mean back stress developed during early plastic deformation was generated by stress transfer to the martensite, the remainder arising from strain hardening of the matrix. A small permanent softening in the Bauschinger test resulted from a reduction of effective stress in the ferrite matrix when the strain path was reversed.     

Effect of epitaxial ferrite on yielding and plastic flow in dual phase steel in tension and compression

Abstract

A low carbon, microalloyed steel was heat treated to obtain dual phase microstructures containing constant levels of 18 and 25 vol.-% martensite at two levels of microstructural refinement and with varying epitaxial ferrite content. Tensile and compression tests were conducted at a strain sensitivity of 2 × 10^-5. Elastic limits in tension and compression were indistinguishable and very low, suggesting that mobile dislocations were present in the ferrite as a consequence of stress relaxation processes. These mobile dislocations accommodated the volume increase accompanying the austenite to martensite transformation during heat treatment. Epitaxial ferrite had little effect on the 0·2% proof stress, but average proof stresses were generally higher in compression than in tension owing to residual stresses in the martensite and ferrite following heat treatment. The residual stresses calculated from this asymmetry in the proof stresses were small because of stress relaxation in the ferrite at the temperature at which the martensite formed. Epitaxial ferrite significantly increased uniform elongation in tension with a small decrease in tensile strength for both levels of martensite in the finer microstructure but only at the 18 vol.-% martensite level in the coarser microstructure. The cause of the increased ductility was the effect of epitaxial ferrite on the work hardening rate between approximately 0·5 and 3% strain; epitaxial ferrite reduced the work hardening rate in this range of strain.     

硅对烧结M3∶2高速钢回火相及力学性能的影响

为研究硅对烧结高速钢力学性能的影响,采用真空热处理炉在1230℃对含0.4%碳粉及硅添加量在0～3.0%的M3∶2高速钢进行烧结,在500～600℃对烧结后的试样进行二次回火.采用X射线衍射仪,扫描电镜及能谱分析等手段研究了不同硅添加量对回火态高速钢的物相特征及力学性能的影响规律.物相分析结果表明,添加硅后,硅主要分布在回火马氏体及M6C碳化物中,而在MC碳化物中含量较低.回火马氏体组织中硅的含量随硅添加量的增加而增加,同时,硅的添加还显著影响回火马氏体组织中铁素体相的晶格常数,在硅添加量为0.7%时,铁素体相达到最大的晶格常数.力学性能测试结果表明,适量硅的添加可提高二次硬化效果,添加0.7%硅的高速钢在550℃二次回火后获得了最佳的硬度和弯曲强度.     

NM360钢与Q345钢异种钢焊接接头组织与性能研究

为了解NM360钢与异种钢焊接应用过程中焊接接头的力学性能,本文对NM360调质钢和Q345热轧钢采用气体保护焊进行异种钢焊接,对焊接接头进行了力学性能试验及微观组织观察,并分析了NM360钢ICHAZ的软化机理.研究表明:Q345热轧钢焊接接头CGHAZ组织为贝氏体+魏氏组织,为HAZ硬度值最高的区域,FGHAZ和ICHAZ组织为P+F;NM360调质钢焊接接头CGHAZ组织为低碳马氏体,FGHAZ组织为低碳马氏体+少量的粒状贝氏体,晶粒细小,为HAZ硬度值最高的区域,ICHAZ组织为回火马氏体+铁素体+粒状贝氏体,铁素体组织是造成ICHAZ硬度值大幅度降低的原因.     

Crystallographic texture evolution and martensite transformation in the strain hardening process of a ferrite-based low density steel

The strain-induced martensite transformation is of great importance in the strain hardening process of ferrite based low-density steel.Based on the microstructure analysis,the texture evolution and martensite transformation behavior in the strain hardening process were studied.The results show that martensite transformation accompanied by TWIP effect and high density dislocations maintains the con-tinuous hardening stage.As the strain increases,the texture of retained austenite evolves towards the F orientation{111}〈112〉,which is not conducive to martensite transformation.After the strain of 5％,the number of austenite grains with high Schmid factor orientations is gradually increased,and then signif-icantly reduced when the strain is over 10％due to the occurrence of martensitic transformation,which results in a high martensitic transformation rate.However,the unfavorable orientation and the reduced grain size of austenite slow down the martensite transformation at the final hardening stage.Moreover,because of the coordination deformation of austenite grains,strain preferentially spreads between adja-cent austenite grains.Consequently,the martensite transformation rate in strain hardening process is dependent on the orientation and grain size evolution of austenite,leading to a differential contribution to each strain hardening stage.     

A study on micro-mechanical deformation behaviour of heat-treated 20MnMoNi55 steel

Several heat treatment procedures are designed considering critical temperatures of phase transformation evaluated through dilatometric testing of 20MnMoNi55 steel to transform low carbon bainitic as-received material into ferrite-martensite dual-phase steels consisting of varied martensite fractions. A thorough metallographic study correlated with the micro-hardness of constituent phases ensures morphological characteristics along with its fractional variations in as-received and dual-phase steels. The impact of fractional variation in constituent phases on the uniaxial monotonic deformation characteristics of dual-phase steels has been observed with a correlation study between experimental tensile and finite element simulated results. Therefore, a physical-based model with a 2-dimensional representative volume element has been established, addressing actual morphological characteristics obtained from metallographic studies. Moreover, the constitutive flow behaviours of ferrite and martensite are also derived from the dislocation-based hardening model to address the actual deformation phenomenon. Finally, an inhomogeneous deformation behaviour among constituent phases and localization of plastic strain in ferrite matrix has been observed with von-Mises stress, and equivalent plastic strain distribution through finite element simulated results. This phenomenon is again confirmed with kernel average misorientation mapping and geometrically necessary dislocation density evaluation through electron backscattered diffraction of tensile samples subjected to different degrees of plastic strain.     

Tensile deformation of a duplex Fe-20Mn-9Al-0.6C steel having the reduced specific weight

The room temperature deformation characteristics of a duplex Fe-20Mn-9Al-0.6C steel with the reduced specific weight of 6.84 g/cm³ in the fully solutionized state were described in conjunction with the deformation mechanisms of its constituent phases. The phase fraction was insensitive to annealing temperature in the range of 800-1100 °C. The ferrite grain size was also nearly unaltered but the austenite grain size slightly increased with increasing annealing temperature. This revealed that there is little window to control the microstructure of the steel by annealing. The steel exhibited a good combination of strength over 800 MPa and ductility over 45% in the present annealing conditions. Ferrite was harder than austenite in this steel. Strain hardening of both phases was monotonic during tensile deformation, but the strain hardening exponent of austenite was higher than that of ferrite, indicating the better strain hardenability of austenite. In addition, the strain hardening exponent of austenite increased but that of ferrite remained unchanged with increasing annealing temperature. The overall strain hardening of the steel followed that of austenite. Considering element partitioning by annealing, the stacking fault energy of austenite of the steel was estimated as ∼70 mJ/m². Even with the relatively high stacking fault energy, planar glide dominantly occurred in austenite. Neither strain induced martensite nor mechanical twins formed in austenite during tensile deformation. Ferrite exhibited the deformed microstructures typically observed in the wavy glide materials, i.e. dislocation cells. The mechanical properties of the present duplex steel were compared to those of advance high strength automotive steels recently developed.     

硼对刃具钢组织与性能的影响

为研制开发适合水淬的新型刃具钢,采用显微组织观察、力学性能测试、热处理试验和磨粒磨损试验等技术手段,对比研究了含硼中碳钢与不含硼的65Mn钢热轧后与热处理后的显微组织和应用性能.结果表明:热轧态中碳含硼钢中存在较多铁素体相,强硬性更低,韧塑性更好;中碳含硼钢水淬回火后组织为回火马氏体,硬度可达50 HRC以上,高于油淬回火的65Mn钢,韧塑性和耐磨性也明显好于65Mn钢.中碳含硼钢完全适合水淬工艺,减少了工业污染,符合环保要求.     

焊后热处理对T92钢焊接接头组织及性能的影响

通过模拟现场热处理工艺,研究了T92钢焊接接头在不同回火温度下的组织和性能。结果表明,焊缝硬度和母材抗拉强度均随回火温度的升高而降低。接头处未回火的马氏体粗大,呈细针状;740-780℃回火,马氏体组织变细,板条特征明显;超过780℃,马氏体板条特征消失,表现为屈氏体组织;随回火温度升高,母材碳化物产生偏聚,铁素体含量增加;780℃以下回火母材力学性能满足ASME标准要求。     

Microstructural evolution and tensile behaviour of medium carbon microalloyed steel processed through two thermomechanical routes

Abstract

A multiphase microstructure was obtained in a medium carbon microalloyed steel using two step cooling (TSC) from a lower than usual finish forging/rolling temperature (800–850°C). A low temperature anneal was then used to optimise the tensile properties. A multiphase microstructure (ferrite–bainite–martensite) resulted from forging as well as rolling. These were characterised using optical and scanning and transmission electron microscopy. X-ray diffraction, transmission electron microscopy and hardness measurements were used for phase identification. Tensile properties and work hardening curves were obtained for both the forged and the rolled multiphase variants. A Jaoul–Crussard (J–C) analysis was carried out on the tensile data to understand the basic mode of deformation behaviour. Rolling followed by the TSC process produced a uniform microstructure with a very fine grain boundary allotriomorphic ferrite, in contrast to the forged variety, which contained in addition coarse idiomorphic ferrite. The volume fraction of ferrite and its contiguity ratio in the rolled microstructure were greater than in the forged grade. The rolled microstructure exhibited a better combination of strength and toughness than that of the forged material. The rolled steel work hardened more than the forged variety owing to its fine, uniform (bainite–martensite and ferrite) microstructure. Retained austenite present in these steels underwent a strain induced transformation to martensite during tensile deformation. The J–C analysis of the work hardening rates revealed typical three stage behaviour in both varieties during tensile deformation.     

Microscopic deformation behaviour of martensitic–ferritic dual-phase steels

Abstract

The deformation behaviour of the two phases of three plain carbon dual–phase steels after various treatments has been studied using a scanning electron microscope equipped with a tensile straining stage. The distribution of strains between the ferrite and martensite phases, as well as among the different grains of each phase, was observed to be inhomogeneous. The martensite/ferrite strain ratio, which defines the degree of uniformity of straining between the phases, depends on the microstructural parameters of the steels: it increases with increasing volume fraction of martensite, but decreases as the carbon content of the martensite increases. Tempering at various temperatures causes a decrease in the martensite/ferrite microhardness ratio and hence causes an increase in the strain ratio. The macroscopic strain of the specimen at which the martensite begins to deform was also found to be dependent on the microstructural parameters. Regions of applicability of the existing theories of the strength of dual–phase steels can be estimated according to the deformation condition of the martensite.

MST/235     

Acoustic emissions during tensile test of DC06 and HCT600X

In this paper the acoustic emission behaviour during tensile tests of the materials DC06 and HCT600X is studied. Two steels with different characteristics (mild deep‐drawing steel DC06 and high‐strength steel HCT600X) are consciously chosen to show the influence of the material properties on the generated acoustic emissions. The acoustic emission behaviour and the corresponding signals differ clearly from each other. In addition, the effect of the strain rate as well as the rolling direction (0°, 90°) on the acoustic emission behaviour is investigated. Both parameters have a significant influence on the resulting acoustic emissions during tensile deformation. Furthermore, a new criterion based on the acoustic emission parameter FCOG (centroid frequency) for detection of damage beginning in dual‐phase steels is developed. The criterion supports the assumption that during tensile deformation of dual‐phase steels two failure mechanisms, ferrite/martensite interface decohesion and martensite phase fracture, exist.