Bubble size as a function of some situational variables in mechanical flotation machines简

The specific results of the work investigating the effect of gas density and water temperature on bubble size were present.These were surrogate variables designed to investigate the effect of viscosity（varying water temperature） and altitude（varying gas density）.The results show that there is a measurable but relatively small effect of gas density on bubble size.The D32 is revealed to increase proportionally as（ρ0/ρg）0.132.The projected impact on flotation kinetics at 4500 m versus sea level is small,of the order of 0.5% recovery loss for a bank of eight flotation cells.The effect of water temperature（4-40 °C） on bubble size is more significant than gas density.The relationship correlates with water viscosity values quite closely.A finding that D32 increases proportionally as（μ/μ20）0.776 highlights the importance of accounting for viscosity effects if,for example,large process temperature fluctuations or deviation from design/test conditions are expected.     

Bonding characteristics of the Al2O3-metal composite coating fabricated onto carbon steel by combustion synthesis

The fabrication of an alumina-metal composite coating onto a carbon steel substrate by using a self-propagating high-temperature synthesis technique was demonstrated. The effects of the type and thickness of the pre-coated layer on the binding structure and surface qual- ity of the coating were systematically investigated. The macrostructure, phase composition, and bonding interface between the coating and the substrate were investigated by scanning electronic microscopy （SEM）, X-ray diffraction （XRD）, and energy-dispersive X-ray spectrometry （EDS）. The diffraction patterns indicated that the coating essentially consisted of α-Al2O3, Fe（Cr）, and FeO-Al2O3. With an increase in the thickness of the pre-coated working layer, the coating became more smooth and compact. The transition layer played an important role in enhancing the binding between the coating and the substmte. When the pre-coated working layer was 10 mm and the pre-coated transition layer was 1 ram, a compact structure and metallurgical bonding with the substrate were obtained. Thermal shock test results indicated that the ceramic coating exhibited good thermal shock resistance when the sample was rapidly quenched from 800℃ to room temperature by plunging into water.     

Preparation of zeolite NaA for CO2 capture from nickel laterite residue

Zeolite NaA was successfully prepared from nickel laterite residue for the first time via a fusion-hydrothermal procedure. The structure and morphology of the as-synthesized zeolite NaA were characterized with a range of experimental techniques, such as X-ray diffraction, scanning electronic microscopy, and infrared spectroscopy. It was revealed that the structures of the produced zeolites were dependent on the molar ratios of the reactants and hydrothermal reaction conditions, so the synthesis conditions were optimized to obtain pure zeolite NaA. Adsorption of nitrogen and carbon dioxide on the prepared zeolite NaA was also measured and analyzed. The results showed that zeolite NaA could be prepared with reasonable purity, it had physicochemical properties comparable with zeolite NaA made from other methods, and it had excellent gas adsorption properties, thus demonstrating that zeolite NaA could be prepared from nickel laterite residue.     

Brazing behavior of ultrafine cemented carbide with stainless steel

In order to investigate the effects of brazing temperature, heating rate and cooling methods on shear strength, hardness, magnetic saturation and coercivity of the ultrafine cemented carbide, the ultrafine cemented carbide was fabricated according to conventional powder metallurgical procedures, and then brazed to the stainless steel with silver-based filler alloy by supersonic frequency induction brazing. The microstructure was observed using scanning electron microscope （SEM）, energy dispersive spectroscopy （EDS） and the magnetic properties were tested utilizing coercimeter and cobalt magnetism instrument. The results show that no micro-crack is found in the cemented carbide after brazing because of silver-based sandwich compound used as filler alloy. In the melted silver layer, there is more carbon in the region adjacent to the cemented carbide. Varied shear strengths, hardnesses, magnetic saturations and coercivities are present under different brazing temperatures, heating rates and coolings. This phenomenon is correlated with some factors such as wettability and fluidity of filler alloy, brazing stress, oxidation of cemented carbide, and allotrope transition of cobalt. Shear strength reaches the maximum of 340 MPa and hardness of ultrafine cemented carbide remains 1879 HV at the brazing temperature of 730℃. The carbon increases with the of increase of the heating rate. What＇s more, and there is no r/phase found under this condition. content decreases with the increase of brazing temperature, and it the lowest magnetic saturation reaches 81.8% of the theoretic value,     

Transformation and performance of granular sequence batch reactor under conventional organic loading rate condition

Laboratory experiments were conducted to investigate the transformation and performance of a granular sequence batch reactor（SBR） under the conventional organic loading rate（OLR） condition.Aerobic granules were successfully cultivated in a SBR by means of alternative feeding load combined with reducing settling time after 60 d operational period.Subsequently,the black fungal granules were presented in reactor because of the filamentous overgrowth on the surface of aerobic granules.A small amount of fungal granules had no effect on the performance of granular SBR.Aerobic granules completely vanished and fungal granules eventually became the dominant species in subsequent 90 d operation after granulation.The three-dimensional excitation emission matrix（EEM） spectra result shows that the extracellular polymeric substances（EPS） component in both granules has no much difference,whereas the content of EPS in fungal granules is higher than that in bacterial granules.Due to their low bioactivity,the chemical oxidation demand（COD） and NH4-N removal efficiencies gradually decrease from 90.4%–96.5% and 99.5% to 71.8% and 32.9% respectively while the fungal granules become dominant in the SBR.     

Effect of fiber angle on LYP steel shear walls behavior简

Steel shear wall（SSW） was properly determined using numerical and experimental approaches.The properties of SSW and LYP（low yield point） steel shear wall（LSSW） were measured.It is revealed that LSSW exhibits higher properties compared to SSW in both elastic and inelastic zones.It is also concluded that the addition of CFRP（carbon fiber reinforced polymers） enhances the seismic parameters of LSSW（stiffness,energy absorption,shear capacity,over strength values）.Also,stress values applied to boundary frames are lower due to post buckling forces.The effect of fiber angle was also studied and presented as a mathematical equation.     

Analysis and design of resistance-wire heater in MOCVD reactor

Metal organic chemical vapor deposition（MOCVD） is a key equipment in the manufacturing of semiconductor optoelectronic devices and microwave devices in industry. Heating system is a vital part of MOCVD. Specific heating device and thermal control technology are needed for each new reactor design. By using resistance-wire heating MOCVD reaction chamber model, thermal analysis and structure optimization of the reactor were developed from the vertical position and the distance between coils of the resistance-wire heater. It is indicated that, within a certain range, the average temperature of the graphite susceptor varies linearly with the vertical distance of heater to susceptor, and with the changed distances between the coils; furthermore, single resistance-wire heater should be placed loosely in the internal and tightly in the external. The modulate accuracy of the temperature field approximately equals the change of the average temperature corresponding to the change of the coil position.     

Effect of tempering temperature on the mechanical properties and microstructure of an copper-bearing low carbon bainitic steel

The effect of tempering temperature on the microstructure and mechanical properties of ultra-high strength, copperbearing, low-carbon bainitic steel has been investigated in the experiment. The results showed that the microstructure was mainly the laths of bainite in the as-quenched steel. The bainitic laths were restored and combined after the steel tempered at various tempera- tures. There were rnartensite/austenite （M/A） islands and numerous dislocations within and between the bainitic laths, while very t-me precipitates of ε-Cu were also observed within the laths. With increasing the tempered temperature from 400 to 600℃, the yield strength （YS） increased from 877 to 957 MPa, whereas the ultimate tensile strength （UTS） decreased from 1020 to 985 MPa. The Charpy V-notch （CVN） varied from 68.5 to 42 J, and the value was minimal for the steel tempered at 500℃. 2008 University of Science and Technology Beijing. All rights reserved.     

Effect of nanofibers at surface of carbon fibers on microstructure of carbon/carbon composites during chemical vapor infiltration

Before densification by chemical vapor infiltration,carbon or SiC nanofibers were grown on the surface of carbon fibers by catalytic chemical vapor deposition using electroplated Ni as catalyst.The modification and mechanism of nanofibers on the pyrocarbon deposition during chemical vapor infiltration were investigated.The results show that the nanofibers improve the surface activity of the carbon fibers and become active nucleation centers during chemical vapor infiltration.They can induce the ordered deposition of pyrocarbon and adjust the interface bonding between pyrocarbon and carbon fibers during the infiltration.     

Effects of magnetic fields on Fe-Si composite electrodeposition

Coatings containing Fe-Si particles were electrodeposited on 3.0wt% Si steel sheets under magnetic fields. The effects of magnetic flux density （MFD）, electrode arrangement and current density on the surface morphology, the silicon content in the coatings and the cathode current efficiency were investigated. When a magnetic field was applied parallel to the current and when the MFD was less than 0.5 T, numerous needle-like structures appeared on the coating surface. With increasing MFD, the needle-like structures weakened and were transformed into dome-shaped structures. Meanwhile, compared to results obtained in the absence of a magnetic field, the silicon content in the coatings significantly increased as the MFD was increased for all of the samples obtained using a vertical electrode system. However, in the case of an aclinic electrode system, the silicon content decreased. Furthermore, the cathode current efficiency was considerably diminished when a magnetic field was applied. A possible mechanism for these phenomena was discussed.     

Interference management via access control and mobility prediction in two-tier heterogeneous networks

Abstract： Two-tier heterogeneous networks （HetNets）, where the current cellular networks, i.e., macrocells, are overlapped with a large number of randomly distributed femtocells, can potentially bring significant benefits to spectral utilization and system capacity. The interference management and access control for open and closed femtocells in two-tier HetNets were focused. The contributions consist of two parts. Firstly, in order to reduce the uplink interference caused by MUEs （macrocell user equipments） at closed femtocells, an incentive mechanism to implement interference mitigation was proposed. It encourages femtoeells that work with closed-subscriber-group （CSG） to allow the interfering MUEs access in but only via uplink, which can reduce the interference significantly and also benefit the marco-tier. The interference issue was then studied in open-subscriber-group （OSG） femtocells from the perspective of handover and mobility prediction. Inbound handover provides an alternative solution for open femtocells when interference turns up, while this accompanies with PCI （physical cell identity） confusion during inbound handover. To reduce the PCI confusion, a dynamic PCI allocation scheme was proposed, by which the high handin femtocells have the dedicated PCI while the others share the reuse PCIs. A Markov chain based mobility prediction algorithm was designed to decide whether the femtoeell status is with high handover requests. Numerical analysis reveals that the UL interference is managed well for the CSG femtocell and the PCI confusion issue is mitigated greatly in OSG femtocell compared to the conventional approaches.     

Fabrication and densification enhancement of SiC-particulate-reinforced copper matrix composites prepared via the sinter-forging process

The fabrication of copper （Cu） and copper matrix silicon carbide （Cu/SiCp） particulate composites via the sinter-forging process was investigated. Sintering and sinter-forging processes were performed under an inert Ar atmosphere. The influence of sinter-forging time, temperature, and compressive stress on the relative density and hardness of the prepared samples was systematically investigated and subsequently compared with that of the samples prepared by the conventional sintering process. The relative density and hardness of the composites were enhanced when they were prepared by the sinter-forging process. The relative density values of all Cu/SiCp composite samples were observed to decrease with the increase in SiC content.     

Effect of substrate doping on threshold voltages of buried channel pMOSFET based on strained-SiGe technology

The effect of substrate doping on the threshold voltages of buried channel pMOSFET based on strained-SiGe technology was studied. By physically deriving the models of the threshold voltages, it is found that the layer which inversely occurs first is substrate doping dependent, giving explanation for the variation of plateau observed in theC-V characteristics of this device, as the doping concentration increases. The threshold voltages obtained from the proposed model are-1.2805 V for buried channel and-2.9358 V for surface channel at a lightly doping case, and-3.41 V for surface channel at a heavily doping case, which agrees well with the experimental results. Also, the variations of the threshold voltages with several device parameters are discussed, which provides valuable reference to the designers of strained-SiGe devices.     

Desulfurization ability of refining slag with medium basicity

The desulfurization ability of refining slag with relative lower basicity （B） and Al2O3 content （B = 3.5-5.0; 20wt%-25wt% Al2O3） was studied. Firstly, the component activities and sulfide capacity （Cs） of the slag were calculated. Then slag-metal equilibrium experiments were carried out to measure the equilibrium sulfur distribution （Ls）. Based on the laboratorial experiments, slag composition was optimized for a better desulfurization ability, which was verified by industrial trials in a steel plant. The obtained results indicated that an MgO-saturated CaO-Al2O3-SiO2-MgO system with the basicity of about 3.5-5.0 and the Al2O3 content in the range of 20wt%-25wt% has high activity of CaO （αCaO）, with no deterioration of Cs compared with conventional desulfurization slag. The measured Ls between high-strength low-alloyed （HSLA） steel and slag with a basicity of about 3.5 and an Al2O3 content of about 20wt% and between HSLA steel and slag with a basicity of about 5.0 and an Al2O3 content of about 25wt% is 350 and 275, respectively. The new slag with a basicity of about 3.5-5.0 and an Al2O3 content of about 20wt% has strong desulfurization ability. In particular, the key for high-efficiency desulfurization is to keep oxygen potential in the reaction system as low as possible, which was also verified by industrial trials.     

Production of HfO2 thin films using different methods： chemical bath deposition,SILAR and sol-gel process

Hafnium oxide thin films （HOTFs） were successfully deposited onto amorphous glasses using chemical bath deposition, successive ionic layer absorption and reaction （SILAR）, and sol-gel methods. The same reactive precursors were used for all of the methods, and all of the films were annealed at 300℃ in an oven （ambient conditions）. After this step, the optical and structural properties of the films produced by using the three different methods were compared. The structures of the films were analyzed by X-ray diffTaction （XRD）. The optical properties are investigated using the ultraviolet-visible （UV-VIS） spectroscopic technique. The film thickness was measured via atomic force microscopy （AFM） in the tapping mode. The surface properties and elemental ratios of the films were investigated and measured by scanning electron microscopy and energy-dispersive X-ray spectroscopy （EDX）. The lowest transmittance and the highest reflectance values were observed for the films produced using the SILAR method. In addition, the most intense characteristic XRD peak was observed in the diffraction pattern of the film produced using the SILAR method, and the greatest thickness and average grain size were calculated for the film produced using the SILAR method. The films produced using SILAR method contained fewer cracks than those produced using the other methods. In conclusion, the SILAR method was observed to be the best method for the production of HOTFs.     

Large-scale two-dimensional nonlinear FE analysis on PGA amplification effect with depth and focusing effect of Fuzhou Basin

Based on the explicit finite element（FE） method and platform of ABAQUS,considering both the inhomogeneity of soils and concave-convex fluctuation of topography,a large-scale refined two-dimensional（2D） FE nonlinear analytical model for Fuzhou Basin was established.The peak ground motion acceleration（PGA） and focusing effect with depth were analyzed.Meanwhile,the results by wave propagation of one-dimensional（1D） layered medium equivalent linearization method were added for contrast.The results show that：1） PGA at different depths are obviously amplified compared to the input ground motion,amplification effect of both funnel-shaped depression and upheaval areas（based on the shape of bedrock surface） present especially remarkable.The 2D results indicate that the PGA displays a non-monotonic decreasing with depth and a greater focusing effect of some particular layers,while the 1D results turn out that the PGA decreases with depth,except that PGA at few particular depth increases abruptly; 2） To the funnel-shaped depression areas,PGA amplification effect above 8 m depth shows relatively larger,to the upheaval areas,PGA amplification effect from 15 m to 25 m depth seems more significant.However,the regularities of the PGA amplification effect could hardly be found in the rest areas; 3） It appears a higher regression rate of PGA amplification coefficient with depth when under a smaller input motion; 4） The frequency spectral characteristic of input motion has noticeable effects on PGA amplification tendency.     

Dielectric,piezoelectric, and ferroelectric properties of lanthanum-modified PZTFN ceramics

Specimens of Pb1-1.5xLax（Zr0.53 Ti0.47）1-y-zFeyNb2O3 （x = 0, 0.004, 0.008, 0.012, and 0.016, y = z = 0.01） （PZTFN） ceramics were synthesized by a semi-wet route. In the present study, the effect of La doping was investigated on the structural, microstructural, dielectric, piezoelectric, and ferroelectric properties of the ceramics. The results show that, the tetragonal （space group P4mm） and rhombohedral （space group R3c） phases are observed to coexist in the sample at x = 0.012. Microstructural investigations of all the samples reveal that La doping inhibits grain growth. Doping of La into PZTFN improves the dielectric, ferroelectric, and piezoelectric properties of the ceramics. The hys- teresis loops of all specimens exhibit nonlinear behavior. The dielectric, piezoelectric and ferroelectric properties show a maximum response atx 〉 0.012, which corresponds to the morphotropic phase boundary （MPB）.     

Free clustering optimal particle probability hypothesis density（PHD） filter

As to the fact that it is difficult to obtain analytical form of optimal sampling density and tracking performance of standard particle probability hypothesis density（P-PHD） filter would decline when clustering algorithm is used to extract target states,a free clustering optimal P-PHD（FCO-P-PHD） filter is proposed.This method can lead to obtainment of analytical form of optimal sampling density of P-PHD filter and realization of optimal P-PHD filter without use of clustering algorithms in extraction target states.Besides,as sate extraction method in FCO-P-PHD filter is coupled with the process of obtaining analytical form for optimal sampling density,through decoupling process,a new single-sensor free clustering state extraction method is proposed.By combining this method with standard P-PHD filter,FC-P-PHD filter can be obtained,which significantly improves the tracking performance of P-PHD filter.In the end,the effectiveness of proposed algorithms and their advantages over other algorithms are validated through several simulation experiments.     

Effects of sintering temperature on the microstructural evolution and wear behavior of WCp reinforced Ni-based coatings

This article focuses on the microstructural evolution and wear behavior of 50wt%WC reinforced Ni-based composites prepared onto 304 stainless steel substrates by vacuum sintering at different sintering temperatures. The microstructure and chemical composition of the coatings were investigated by X-ray diffraction （XRD）, differential thermal analysis （DTA）, scanning and transmission electron microscopy （SEM and TEM） equipped with energy-dispersive X-ray spectroscopy （EDS）. The wear resistance of the coatings was tested by thrust washer testing. The mechanisms of the decomposition, dissolution, and precipitation of primary carbides, and their influences on the wear resistance have been discussed. The results indicate that the coating sintered at 1175℃ is composed of fine WC particles, coarse M6C （M=Ni, Fe, Co, etc.） carbides, and discrete borides dispersed in solid solution. Upon increasing the sintering temperature to 1225℃, the microstructure reveals few incompletely dissolved WC particles trapped in larger M6C, Cr-rich lamellar M23C6, and M3C2 in the austenite matrix. M23C6 and M3C2 precipitates are formed in both the γ/M6C grain boundary and the matrix. These large-sized and lamellar brittle phases tend to weaken the wear resistance of the composite coatings. The wear behavior is controlled simultaneously by both abrasive wear and adhesive wear. Among them, abrasive wear plays a major role in the wear process of the coating sintered at 1175℃, while the effect of adhesive wear is predominant in the coating sintered at 1225℃.     

Fluidized bed coating efficiency and morphology of coatings for producing Al-based nanocomposite hollow spheres

Abstract： We performed fluidized bed coating ofAl-based nanoeomposite powder-binder suspensions onto polymer substrates. The effects of the type and amount of the binder and nanoparticle additive on the coating process efficiency and coating characteristics were investigated. The efficiency decreased from 52% to 49% as the processing time increased from 15 to 20 min. However, the amount and thickness of the coating also increased as the processing time and amount of the binder were increased. The addition of nanoparticles to the system decreased the thickness of the coating from 222 to 207 μm when polyvinyl alcohol （PVA） was used as a binder. The suspension containing 3wt% R-4410 binder exhibited the greatest efficiency of 60%.