The compatibility of transition metal oxide/carbon composite anode and ionic liquid electrolyte for the lithium-ion battery

Three types of transition metal oxide/carbon composites including Fe₂O₃/C, NiO/C and CuO/Cu₂O/C synthesized via spray pyrolysis were used as anode for lithium ion battery application in conjunction with two types of ionic liquid: 1 M LiN(SO₂CF₃)₂ (LiTFSI) in 1-ethyl-3-methyl-imidazolium bis(fluorosulfonlyl)imide (EMI-FSI) or 1-methyl-1-propylpyrrolidinium bis(fluorosulfonyl)imide (Py13-FSI). From the electrochemical measurements, the composite electrodes using Py13-FSI as electrolyte show much better electrochemical performance than those using EMI-FSI as electrolyte in terms of reversibility. The Fe₂O₃/C composite shows the highest specific capacity and the best capacity retention (425 mAh g⁻¹) under a current density of 50 mA g⁻¹ for up to 50 cycles, as compared with the NiO/C and CuO/Cu₂O/C composites. The present research demonstrates that Py13-FSI could be used as an electrolyte for transition metal oxides in lithium-ion batteries.     

Membrane-based electrolyte sheets for facile fabrication of flexible dye-sensitized solar cells

New electrolyte sheets based on porous polyethylene membranes for flexible dye-sensitized solar cells have been developed. Ionic liquid electrolytes are accommodated in commercial polyethylene membranes to form the electrolyte sheets. The morphology of membranes and iodine concentrations in ionic liquid are varied. The electrochemical measurement results show that the morphology, pore structure, and iodine concentration affect mass transport in electrolyte sheet, as well as charge transfer between platinum electrode and electrolyte sheet greatly. Based on these electrolyte sheets, lamination method instead of conventional vacuum injection of electrolyte is used to fabricate flexible dye-sensitized solar cells. Optimal device with an open-circuit voltage (V_oc) of 0.63 V, a fill factor of 0.58, and a short-circuit current density (J_sc) of 6.17 mA cm⁻² at an incident light intensity of 100 mW cm⁻² is obtained, which yields a light-to-electricity conversion efficiency of 2.25%.     

A novel polymeric gel electrolyte systems containing magnesium salt with ionic liquid

A new polymeric gel electrolyte system consisting of poly(ethylene oxide)-modified polymethacrylate (PEO-PMA) with organic ionic liquid dissolving magnesium salt, Mg[(CF₃SO₂)₂N]₂, has been developed. The ionic conductance and electrochemical properties of the gel films were investigated. The obtained gel film was self-standing, transparent and flexible with sufficient mechanical strength. Thermal analysis of the gel film showed that it is homogeneous and amorphous over a wide temperature range. The highest conductivity, ca. 3.5 mS cm⁻¹ at 60 °C, was obtained for the polymeric gel containing 80 wt.% of the liquid component that consists of 80 mol% of EMITFSI (1-ethyl-3-methylimidazolium bis(trofluoromethylsulfonyl)imide) and 20 mol% of Mg[(CF₃SO₂)₂N]₂. The sort of the ionic liquid affected much on the ionic conductivity of the gel. The dc polarization of a Pt/polymeric gel electrolyte/Mg cell proved that the magnesium ion (Mg²⁺) can mobile in the present polymeric gel system.     

A new carbon nanotubes (CNTs)–poly acrylonitrile (PAN) composite electrolyte for solid state dye sensitized solar cells

A new carbon nanotube (CNTs)–poly acrylonitrile (PAN) composite electrolyte was prepared by the thermal polymerization of acrylonitrile (AN) with CNTs for solid-state dye sensitized solar cells (DSSCs). It was found that the uniform CNT–PAN composite was formed due to the thermal polymerization of AN on CNTs. The strong bonding between CNTs and PAN could be confirmed by the characterization of XPS and Raman spectroscopy, resulting in the lowering of crystallinity and the increasing the ionic conductivity of composite electrolytes. On comparison with bare CNTs and the other composite electrolytes, the formation of triiodide (I₃⁻) ions in CNT–PAN composite electrolytes was drastically increased which was expected from the high ionic conductivity of electrolyte via I₃⁻/I⁻ redox couple. DSSCs fabricated with CNT–PAN composite electrolytes achieved relatively high conversion efficiency of 3.9% with an open circuit voltage (V_OC) of 0.57 V, short circuit current density (J_SC) of 10.9 mA/cm² and fill factor of 63.6%, which attributed to supply the higher extent of I₃⁻ ions from CNT–PAN composite electrolyte during the charge transport process.     

Electrochemical investigation of LiMn2O4 cathodes in gel electrolyte at various temperatures

A composite lithium battery electrode of LiMn₂O₄ in combination with a gel electrolyte (1 M LiBF₄/24 wt% PMMA/1:1 EC:DEC) has been investigated by galvanostatic cycling experiments and electrochemical impedance spectroscopy (EIS) at various temperatures, i.e. −3<T<56 °C. For analysis of EIS data, a mathematical model taking into account local kinetics and potential distribution in the liquid phase within the porous electrode structure was used. Reasonable values of the double-layer capacitance, the exchange-current density and the solid phase diffusion were found as a function of temperature. The apparent activation energy of the charge-transfer (∼65 kJ mol⁻¹), the solid phase transfer (∼45 kJ mol⁻¹) and of the ionic bulk and effective conductance in the gel phase (∼34 kJ mol⁻¹), respectively, were also determined. The kinetic results related to ambient temperature were compared to those obtained in the corresponding liquid electrolyte. The incorporated PMMA was found to reduce the ionic conductivity of the free electrolyte, and it was concluded that the presence of 24 wt% PMMA does not have a significant influence on the kinetic properties of LiMn₂O₄.     

Carbon nanotubes-polyethylene oxide composite electrolyte for solid-state dye-sensitized solar cells

Novel carbon nanotubes (CNTs)-polyethylene oxide (PEO) composite electrolyte for dye-sensitized solar cell (DSSC) was prepared and characterized for the first time. The strong bonding and interaction between CNTs and PEO in CNTs-PEO composites was observed by the characterization of X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and Raman spectra. The introduction of CNTs into PEO matrix significantly improved the electrolyte properties of DSSC such as roughness, amorphicity and ionic conductivity. The solid-state DSSC fabricated with the optimum composite electrolyte (added 1% CNTs in PEO matrix, 1%CNT-PEO) achieved maximum conversion efficiency of 3.5%, an open circuit voltage (V_OC) of 0.589 V, short circuit current density (J_SC) of 10.64 mA/cm² and fill factor (FF) of 56%. The highest IPCE in the DSSC fabricated with 1%CNT-PEO electrolyte is ascribed to the improved ionic conductivity of composite electrolytes and enhanced interfacial contact between electrode and electrolyte.     

Preparation and electrochemical performance of gel polymer electrolytes with a novel star network

Well-defined star shaped polymers with α-Cyclodextrin (α-CD) core linking PMMA-block arms were synthesized by atom transfer radical polymerization (ATRP). Gel polymer electrolytes (GPEs) were prepared by encapsulating electrolyte solution of 1 mol L⁻¹ of LiClO₄/EC-PC (volume 1:1) into the obtained star shaped polymer host. The ionic conductivity of the GPEs and the cycling characteristics of LiCoO₂/GPEs/Graphite cell were studied by electrochemical impedance spectroscopy and charge-discharge testing, respectively. The results indicate that the GPEs have a high ionic conductivity up to 1.63 × 10⁻³ S cm⁻¹ at room temperature and exhibit a high electrochemical stability potential of 4.5 V (vs. Li/Li⁺). The discharge capacity of LiCoO₂/GPEs/Graphite cell is about 98% of its initial discharge capacity after 20 cycles at 0.1 C rate. Discharge capacity of the model cell with GPEs is stable with charge-discharge cycling.     

Preparation and Characterization of Composite Microporous Gel Polymer Electrolytes Containing SiO2(Li+)

In this paper, the single ionic conductor SiO₂(Li⁺) was first synthesized from Tetraethylorthosilicate and γ-(2,3-epoxypropoxy) propyltrimethoxysilane (KH560) by sol–gel hydrolysis and then neutralized by lithium hydroxide in methanol. The poly(vinylidene fluoride) based composite microporous gel polymer electrolytes (CMGPEs) doped with SiO₂(Li⁺) was prepared by phase inversion method and the desirable CMGPEs was obtained after being activated in liquid electrolyte. The physicochemical properties of the CMGPEs were characterized by FT-IR, DSC, XRD, TG, stress–strain response and electrochemical measurements. It was found that with the addition of SiO₂(Li⁺), the degree of crystallization of microporous polymer membrane was decreased while its porosity increased, which could promote the absorption and gelation of liquid electrolyte. In addition, due to vast amount of Li⁺ ions in the SiO₂(Li⁺), it would promote ionic conductivity at room temperature for the CMGPEs. When the content of SiO₂(Li⁺) reached 5 %wt, the ionic conductivity of the CMGPEs could reach 10^?2S/cm order of magnitude at room temperature and the reciprocal temperature dependence of ionic conductivity of as-prepared CMGPEs follow arrhenius equation, in addition, its electrochemical stability window could reach 5.2 V.     

P(VDF-HFP)-based micro-porous composite polymer electrolyte prepared by in situ hydrolysis of titanium tetrabutoxide

A micro-porous composite polymer electrolyte (MCPE) was prepared in situ by adding TiO₂ nanoparticles from the hydrolysis of titanium tetrabutoxide to a solution of poly(vinylidenefluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer. The prepared microporous polymer films (MCPFs) were characterized by scanning electronic microscopy, X-ray diffraction, thermogravimetric analysis, FT-IR and electrochemical interface resistance. After the addition of TiO₂ nanoparticles the polarity of CF₂ groups in the polymer chains and the crystallinity of the MCPFs decreased. When the composite polymer film contained 8.5 wt% of TiO₂ nanoparticles the MCPE exhibited excellent electrochemical properties such as high ionic conductivity, up to 2.40 × 10⁻³ S cm⁻¹ at room temperature.     

Preparation and performance analysis of barium titanate incorporated in corn starch‐based polymer electrolytes for electric double layer capacitor application

Polymer electrolyte membranes composing of corn starch as host polymer, lithium perchlorate (LiClO₄) as salt, and barium titanate (BaTiO₃) as composite filler are prepared using solution casting technique. Ionic conductivity is enhanced on addition of BaTiO₃ by reducing the crystallinity and increasing the amorphous phase content of the polymer electrolyte. The highest ionic conductivity of 1.28 × 10^?2 S cm^?1 is obtained for 10 wt % BaTiO₃ filler in corn starch‐LiClO₄ polymer electrolytes at 75°C. Glass transition temperature (T_g) of polymer electrolytes decreases as the amount of BaTiO₃ filler is increased, as observed in differential scanning calorimetry analysis. Scanning electron microscopy and thermogravimetric analysis are employed to characterize surface morphological and thermal properties of BaTiO₃‐based composite polymer electrolytes. The electrochemical properties of the electric double‐layer capacitor fabricating using the highest ionic conductivity polymer electrolytes is investigated using cyclic voltammetry and charge‐discharge analysis. The discharge capacitance obtained is 16.22 F g^?1. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43275.     

Analysis of carbon dioxide-to-methanol direct electrochemical conversion mediated by an ionic liquid

An intensified process for carbon dioxide capture and conversion is proposed and analyzed, considering an electrochemical parallel plate reactor which processes a CO₂-charged stream from an absorption unit at 40 °C and atmospheric pressure and where the target product of the conversion is methanol.The task-specific ionic liquid 1-(3-aminopropyl)-3-methylimidazolium bromide was selected, synthesized and characterized. This ionic liquid has shown a good absorption capacity, high ionic conductivity, high chemical–electrochemical stability and acts as a charged intermediate (CO₂^*−) stabilizer, enabling the electrochemical reduction of absorbed CO₂.The electrical energy in the electrochemical reactor was estimated to be 8.683 kWh kg (CO₂)⁻¹ or 115.16 g (CO₂) kWh⁻¹, too high to ensure the environmental sustainability of the process. A low concentration of carbon dioxide in the liquid phase, at ambient conditions, implies the need for a high electrode area for the process and is a major hindrance to improving the economy of the process.     

Characterization of poly(vinylidenefluoride-co-hexafluoropropylene)-based polymer electrolyte filled with TiO2 nanoparticles

Nanoscale TiO₂ particle filled poly(vinylidenefluoride-co-hexafluoropropylene) film is characterized by investigating some properties such as surface morphology, thermal and crystalline properties, swelling behavior after absorbing electrolyte solution, chemical and electrochemical stabilities, ionic conductivity, and compatibility with lithium electrode. Decent self-supporting polymer electrolyte film can be obtained at the range of <50 wt% TiO₂. Different optimal TiO₂ contents showing maximum liquid uptake may exist by adopting other electrolyte solution. Room temperature ionic conductivity of the polymer electrolyte placed surely on the region of >10⁻³ S/cm, and thus the film is very applicable to rechargeable lithium batteries. An emphasis is also be paid on that much lower interfacial resistance between the polymer electrolyte and lithium metal electrode can be obtained by the solid-solvent role of nanoscale TiO₂ filler.     

Electrochemical properties of novel ionic liquids for electric double layer capacitor applications

An aliphatic quaternary ammonium salt which has a methoxyethyl group on the nitrogen atom formed an ionic liquid (room temperature molten salt) when combined with the tetrafluoroborate (BF₄⁻) and bis(trifluoromethylsulfonyl)imide [TFSI; (CF₃SO₂)₂N⁻] anions. The limiting oxidation and reduction potentials, specific conductivity, and some other physicochemical properties of the novel ionic liquids, N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium tetrafluoroborate (DEME-BF₄) and DEME-TFSI have been evaluated and compared with those of 1-ethyl-3-methylimidazolium tetrafluoroborate. DEME-BF₄ is a practically useful ionic liquid for electrochemical capacitors as it has a quite wide potential window (6.0 V) and high ionic conductivity (4.8 mS cm⁻¹ at 25 °C). We prepared an electric double layer capacitor (EDLC) composed of a pair of activated carbon electrodes and DEME-BF₄ as the electrolyte. This EDLC (working voltage ∼2.5 V) has both, a higher capacity above room temperature and a better charge-discharge cycle durability at 100 °C when compared to a conventional EDLC using an organic liquid electrolyte such as a tetraethylammonium tetrafluoroborate in propylene carbonate.     

Study on Selective Dimerization of α-Methylstyrenes Promoted by Ionic Liquids

The catalytic systems composed of ionic liquids containing BF₄⁻ anion and HBF₄ showed high catalytic activity to produce 4-methyl-2,4-diphenyl-1-pentene (MDP-1) or 1,1,3-trimethyl-3-phenylindan (TPI) under different temperature conditions. Up to 90.8% selectivity to MDP-1 with a 98.7% conversion of α-methylstyrene was obtained at 60 °C in the presence of [HexMIm]BF₄–HBF₄, while exclusive TPI was yielded when the reaction temperature increased to 120 °C. Further studies showed that another ionic liquid, [BMIm]Cl · 2AlCl₃, could act as an excellent catalyst and solvent for the dimerization of α-methylstyrene to produce TPI. The dimerization of α-methylstyrene catalyzed by [HexMIm]BF₄–HBF₄ and [BMIm]Cl · 2AlCl₃ performed the same reaction mechanism and the proton was the active species.     

Influence of ionic additives NaI/I2 on the properties of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

The ionic additives NaI/I₂ in polymer gel electrolyte not only provide cations, but also affect the liquid electrolyte absorbency of the poly(acrylic acid)-poly(ethylene glycol) hybrid, which results in the change of ionic conductivity of polymer gel electrolyte and the photovoltaic performance of quasi-solid-state dye-sensitized solar cell. With the optimized components of liquid electrolyte containing 0.5 M NaI, 0.05 M I₂, 0.4 M pyridine, 70 vol.% γ-butyrolactone and 30 vol.% N-methylpyrrolidone, a 4.74% power conversion efficiency of quasi-solid-state dye-sensitized solar cell was obtained under 100 mW cm⁻² (AM 1.5) irradiation.     

Enhanced photoelectrochemistry and interactions in cadmium selenide-functionalized multiwalled carbon nanotube composite films

Cadmium selenide-functionalized multiwalled carbon nanotube (CdSe-f-MWCNT) composite films have been synthesized by the percolation of a f-MWCNT dispersion through the macropores of electrodeposited CdSe thin films during electrophoretic deposition. Evidence for efficient charge transfer from CdSe to f-MWCNTs was obtained by photoluminescence quenching and proof for strong interactions was provided by X-ray photoelectron spectroscopy analyses, which revealed a significant decrease in the reduced Se²⁻ content and evolution of new signals due to oxidized Se, and high resolution transmission electron microscopy and atomic force microscopy images of CdSe decorated f-MWCNTs in the composite film. Sputter depth profiling of the composite confirmed a homogeneous mixing of nanoparticulate CdSe and f-MWCNTs. A quasi solid-state photoelectrochemical cell fabricated by coupling the composite film with an ionic liquid based gel polymer electrolyte containing the I₃/I⁻ redox pair not only showed larger photocurrents, photovoltage and incident photon to current conversion efficiency as compared to the analogous CdSe cell but also showed a remarkably enhanced stability to photoerosion. The ability of f-MWCNTs to mediate fast charge transfer and retard charge recombination rate in the composite was also evident from electrochemical impedance spectroscopy (EIS) results. Cell degradation upon exposure was also reflected in the altered EIS parameters such as increased charge transfer resistance and the reduced ease of charge transport through the composite.     

Polymeric ionic liquid membranes as electrolytes for lithium battery applications

A new kind of polymeric ionic liquid (PIL) membrane based on guanidinium ionic liquid (IL) with ester and alkyl groups was synthesized. On addition of guanidinium IL, lithium salt, and nano silica in the PIL, a gel PIL electrolyte was prepared. The chemical structure of the PIL and the properties of gel electrolytes were characterized. The ionic conductivity of the gel electrolyte was 5.07 × 10⁻⁶ and 1.92 × 10⁻⁴ S cm⁻¹ at 30 and 80 °C, respectively. The gel electrolyte had a low glass transition temperature (T _g ) under −60 °C and a high decomposition temperature of 310 °C. When the gel polymer electrolyte was used in the Li/LiFePO₄ cell, the cell delivered 142 mAh g⁻¹ after 40 cycles at the current rates of 0.1 C and 80 °C.     

Electrodeposited Zn–TiO<Subscript>2</Subscript> nanocomposite coatings and their corrosion behavior

The present paper aims to investigate the electrodeposition on steel substrate and the corrosion behavior of Zn–TiO₂ nanocomposite coatings. Zn–TiO₂ composite coatings were electrodeposited on OL 37 steel from an electrolyte containing ZnCl₂, KCl, HBO₃ (pH 5.7) brightening agents and dispersed nanosized TiO₂. Corrosion measurements were performed in 0.2 g L⁻¹ (NH₄)₂SO₄ solution (pH 3) by using electrochemical methods (open-circuit potential measurements, polarization curves, electrochemical impedance spectroscopy). The results of electrochemical measurements were corroborated with those obtained by using non-electrochemical methods (X-ray diffraction, atomic force microscopy and scanning electron microscopy). The results indicate that the composite coatings exhibit higher corrosion resistance as compared to pure Zn coatings and a non-linear dependence of their polarization resistance on TiO₂ concentration in the plating bath was found. The importance of TiO₂ nature and concentration regarding the properties of the composite coatings was demonstrated.     

Effect of surface modified porous inorganic-organic hybrid polyphosphazene nanotubes on the properties of polyethylene oxide based solid polymer electrolytes

2-(2-methyloxyethoxy)ethanol modified poly (cyclotriphosphazene-co-4,4′-sufonyldiphenol) (PZS) nanotubes were synthesized and solid composite polymer electrolytes based on the surface modified polyphosphazene nanotubes added to PEO/LiClO₄ model system were prepared. Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) were used to investigate the characteristics of the composite polymer electrolytes (CPE). The ionic conductivity, lithium ion transference number and electrochemical stability window can be enhanced after the addition of surface modified PZS nanotubes. The electrochemical investigation shows that the solid composite polymer electrolytes incorporated with PZS nanotubes have higher ionic conductivity and lithium ion transference number than the filler SiO₂. Maximum ionic conductivity values of 4.95 × 10⁻⁵ S cm⁻¹ at ambient temperature and 1.64 × 10⁻³ S cm⁻¹ at 80 °C with 10 wt % content of surface modified PZS nanotubes were obtained and the lithium ion transference number was 0.41. The good chemical properties of the solid state composite polymer electrolytes suggested that the inorganic-organic hybrid polyphosphazene nanotubes had a promising use as fillers in solid composite polymer electrolytes and the PEO₁₀-LiClO₄-PZS nanotubes solid composite polymer electrolyte can be used as a candidate material for lithium polymer batteries.     

Ionic liquids based on (fluorosulfonyl)(pentafluoroethanesulfonyl)imide with various oniums

New hydrophobic ionic liquids based on (fluorosulfonyl)(pentafluoroethanesulfonyl)imide ([(FSO₂)(C₂F₅SO₂)N]⁻, FPFSI⁻) anion with various oniums, including imidazolium, tetraalkyl ammonium, pyrrolidinium, and piperidinium, were prepared and characterized. Their physicochemical and electrochemical properties, including phase transitions, thermal stability, viscosity, density, specific conductivity and electrochemical windows, were extensively characterized, and were comparatively studied with the corresponding ionic liquids containing the isomeric but symmetric TFSI⁻ ([(CF₃SO₂)₂N]⁻) anion. These new FPFSI⁻-based ionic liquids display low melting points, low viscosities, good thermal stability, and wide electrochemical windows allowing Li deposition/dissolution. All these desired properties suggest they are potential electrolyte materials for Li (or Li-ion) batteries.