Bright green organic light-emitting devices having a composite electron transport layer

A bright green organic light-emitting device employing a co-deposited Al-Alq₃ layer has been fabricated. The device structure is glass/indium tin oxide (ITO)/ N, N′-diphenyl-N, N′- (3-methylphenyl)-1, 1′-biphenyl-4, 4′-diamine (TPD)/tris(8-quinolinolato) aluminum (Alq₃)/ Al-Alq₃/Al. In this device, Al-Alq₃ is used as electron transport layer (ETL). The device shows an operation voltage of 6.1 V at 20 mA/cm². At optimal condition, the brightness of a device at 20 mA/cm² is 2195 cd/m² achieved a luminance efficiency of 5.64lm/W. The result proves that the composite Al-Alq₃ layer is suitable for the ETL of organic light-emitting devices (OLEDs).     

The electroluminescent investigation of double layer Eu-complex organic electronic luminescence diodes

Double layer organic electronic luminescence diodes (OLEDs) based on europium(dibenzoylmethanato)₃monophenanthroline [Eu(DBM)₃bath], ITO/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′-diamine (TPD)/Eu(DBM)₃bath/LiF/Al have been fabricated. With increasing the thickness of hole transporting layer, the maximum EL efficiency was increased, and the EL efficiency of 10 cd/A was achieved when the thickness of TPD layer was 80 nm; however, at high current density, the EL efficiency of all devices was decreased drastically. Besides, the evolution of EL emission spectra with increasing operating voltage was found, the mechanisms of the symmetry around the ion improved and the annihilation of excited state of Eu(DBM)₃bath were discussed in explaining this phenomenon.     

Deep blue organic light-emitting diode using non anthracene-type fused-ring spiro[benzotetraphene-fluorene] with aromatic wings

We prepared three spirobenzotetraphene-based fused-ring spiro[benzo[ij]tetraphene-7,9′-fluorene] (SBTF) derivatives for use in non anthracene-type deep-blue organic light-emitting diode (OLED) hosts. 3-(2-Naphthyl)-10-naphthylspiro[benzo[ij]tetraphene-7,9′-fluorene] (N-NSBTF), 3-[4-(2-naphthyl)phenyl]-10-naphthylspiro[benzo[ij]tetraphene-7,9′-fluorene] (NP-NSBTF), and 3-(phenyl)-10-naphthylspiro[benzo[ij]tetraphene-7,9′-fluorene] (P-NSBTF) were synthesized via multi-step Suzuki coupling reactions. The optimized device structure – ITO/N,N′-bis-[4-(di-m-tolylamino)phenyl]-N,N′-diphenylbiphenyl-4,4′-diamine (DNTPD, 60 nm)/bis[N-(1-naphthyl)-N-phenyl]benzidine (NPB, 30 nm)/NSBTF hosts: LBD (5%) (20 nm)/aluminum tris(8-hydroxyquinoline) (Alq₃, 20 nm)/LiF/Al – was characterized by its blue electroluminescence to have a current efficiency of 6.25 cd/A, a power efficiency of 5.07 lm/W, and an external quantum efficiency of 5.24% at 18.7 mA/cm² at CIE coordinates of 0.130, 0.149.     

Efficient nondoped organic light-emitting diodes with Cu complex emitter

In Cu^I complex based organic light emitting diodes (OLEDs) a host matrix is traditionally thought to be required to achieve high efficiency. Herein, it is found that the device ITO/MoO₃ (1 nm)/4,4′-N,N′-dicarbazole-biphenyl (CBP, 35 nm)/[Cu(μ-I)dppb]₂ (dppb = 1,2-bis[diphenylphosphino]benzene, 20 nm)/1,3,5-tris(N-phenylbenzimidazole-2-yl)benzene (TPBi, 65 nm)/LiF (1 nm)/Al (100 nm) with a vacuum thermal evaporated nondoped Cu^I complex emissive layer (EML) showed external quantum efficiency and current efficiency of 8.0% and 24.3 cd/A at a brightness of 100 cd/m², respectively, which are comparable to the maximum efficiencies reported in an optimized doped OLED with the same emitter, higher efficiency than the OLED with a [Cu(μ-I)dppb]₂:CBP EML, and much higher efficiencies than the nondoped OLED with a bis(2-phenylpyridine)(acetylacetonate)iridium [Ir(ppy)₂(acac)] EML. A series of reference films and single carrier devices were fabricated and studied to understand the difference between Cu^I and Ir^III complex based nondoped OLEDs.     

基于Alq3光耦合层的新型顶发射蓝光有机电致发光器件

研制了一种结构为Ag/Glass/ITO/TAPC/mCP/mCP∶Firpic/TPBi/LiF/Al/Ag/Alq₃的顶发射有机电致发光器件,通过在ITO玻璃衬底背面生长一层Ag反射膜,使器件发出的蓝光被反射膜反射到顶电极出射。利用顶电极表面的Alq₃光耦合层有效地提升了金属复合阴极的透射率,降低了器件的微腔效应。实验结果表明,当光耦合层厚度为30nm时,获得了最大电流效率和最大亮度分别为8.91cd/A和5758cd/m²的蓝光顶发射有机电致发光器件(TEOLED);同时,在10V电压下,其色坐标为(0.157,0.320),当亮度从1cd/m²变化到5000cd/m²时,其色坐标仅漂移(0.002,0.010),表现出良好的色稳定性。     

Blade coating of Tris(8-hydroxyquinolinato)aluminum as the electron-transport layer for all-solution blue fluorescent organic light-emitting diodes

Organic light-emitting diodes (OLEDs) with a low driving voltage and efficient blue fluorescence were fabricated through blade coating. Tris(8-hydroxyquinolinato)aluminum (Alq₃) is a relatively stable electron-transporting material commonly used in evaporation. However, depositing Alq₃ through a solution process is difficult because of its extremely low solubility organic solvents, a result of its symmetrical molecular structure. In this study, Alq₃ was successfully deposited through blade coating at a very low concentration below 0.1wt%. The OLEDs contained co-dopants BUBD-1 and p-bis(p-N,N-diphenyl-aminostyryl)benzene (DSA-Ph), and a high-band-gap host 2-methyl-9,10-bis(naphthalen-2-yl)anthracene (MADN) as the emission layer with the following structure: ITO/PEDOT:PSS (40 nm)/VB-FNPD (30 nm)/MADN:2% BUBD-1:1% DSA-Ph (50 nm)/TPBI (30 nm)/LiF (0.8 nm)/Al (100 nm)or ITO/PEDOT:PSS (40 nm)/VB-FNPD (30 nm)/MADN:3% BUBD-1 (50 nm)tris(8-hydroxyquinolinato)aluminum (Alq₃; 10 nm)/LiF (0.8 nm)/Al (100 nm). 2,7-disubstituted fluorene-based triaryldiamine(VB-FNPD)is the cross-linking transporting material. The device exhibited a peak current efficiency of 5.67 cd/A for Alq₃ and 5.76 cd/A for TPBI. The device with Alq₃ has operated lifetime seven times higher than the device with TPBI.     

利用石墨烯掺杂在NPB中的OLED性能研究

采用NPB掺杂石墨烯作为空穴传输层,制备有机电致发光器件(OLED),器件结构为ITO/NPB:Graphene(20wt.%)(50nm)/Alq3(80nm)/LiF(0.5nm)/Al(120nm)。将其与标准器件ITO/NPB(50nm)/Alq3(80nm)/LiF(0.5nm)/Al(120nm)作性能比较,研究石墨烯对OLED性能的影响。结果表明,在NPB中掺杂石墨烯薄层的器件,在同等条件下性能最佳,当电流密度为90mA/cm2时器件电流效率达到最大值3.40cd/A,与标准器件最高效率相比增大1.49倍;亮度在15V时达到最大值10 070cd/m2,比标准器件最大亮度增大5.16倍。     

MoO3修饰氧化石墨烯作为空穴注入层影响研究

研究了MoO₃修饰氧化石墨烯(GO)作为空穴注入层的影响。采用旋涂的方法制备了GO, 再真空蒸镀修饰层MoO₃,得到了空穴注入能力强和透过率高的复合薄膜。MoO₃的厚分 别采用0、3、5和8nm。通过优化MoO₃的厚度发现,当MoO₃的厚为5nm时,复合薄膜 的透过率达到最大值,在 550nm的光波长下透光率为88%,且此时采用 复合薄膜作为空穴注入层制备的结构为 ITO/GO/MoO₃(5nm)/NPB(40nm)/Alq₃(40nm)/LiF(1nm)/Al(100nm)的有机电致发光器件(OLED)性能 最佳。通过对OLED进一步的优化,改变Alq₃的厚度,分别取50、60和70nm,测量其电压 、电流、亮度、色坐标和电致发光(EL)光谱等参数发现,当Alq₃的厚为50nm时器件性能最 佳。最终制备了结构为ITO/GO/MoO₃(5nm)/NPB(50nm)/Alq₃(50nm)/LiF(1nm)/Al(100 nm)的OLED,在电压为10V时,最大电流效率达到5.87cd/A,与GO单独作为空穴注入层制备的器件相比,提高了50%。     

功能层界面制备方法对OLED性能的影响

在功能层界面处采用各功能材料共蒸的方法,制备了典型的绿光有机发光器件(OLED)。器件的结构为ITO/NPB(37nm)/(NPB:Alq3)(3nm)/Alq3(27nm):C545T(3%)/Alq3(20nm)/LiF(1nm)/Al(100nm),并与传统的制备方法进行了比较。结果发现,起亮电压从4.5V降低到2.5V,最高耐压从16V提高到21V,最大亮度从13 940cd/m2提高到24 630cd/m2,发光效率由7.0cd/A提高到11.4cd/A。结果表明,本文方法有利于载流子传输,可以有效提高激子形成概率,提高了OLED发光效率。     

Bright,efficient, deep blue-emissive polymer light-emitting diodes of suitable hole-transport layer and cathode design

This study reports the fabrication of efficient deep blue-emissive polymer light-emitting diodes (PLEDs), incorporating a polyfluorene derivative of nonsymmetric and bulky aromatic groups at C-9 position as the light-emissive layer. Another poly(fluorene-co-triphenylamine) (PFO-TPA) derivative of the highest occupied molecular orbital level, −5.3 eV, is used as the hole-injection and -transport layer in the anode part. The thermally crosslinking of styryl groups in PFO-TPA inhibits the solvation of an interlayer in constructing the multilayer device architecture of PLEDs. While applying a cesium carbonate (Cs₂CO₃)/Aluminum (Al) cathode rather than Calcium (Ca)/Al, the device has the superior performance (i.e. one order of magnitude higher). Experimental results indicate that the interfacial reactions at the polymer/Ca junction, as characterized in this study, significantly degrade the luminescence properties and the device performance. Moreover, Cs₂CO₃/Al is a highly favorable cathode in fabricating polyflourene-based PLEDs. The device of the optimal configuration has a decent deep blue emission centered at 430–450 nm of the Commission Internationale de l’Eclairage chromaticity coordinates, (0.15, 0.14), with a maximum brightness of 35054.2 cd/m² and luminous efficiency of 14.0 cd/A (at 2975.0 cd/m²).     

Effect of Al:Ag alloy cathode on the performance of transparent organic light-emitting devices

Transparent organic light-emitting devices (TOLEDs) based on a stacked alloy cathode of LiF/Al:Ag are investigated. The devices have a structure of indium-tin-oxide (ITO)/4,4′,4′′-Tris[2-naphthyl(phenyl)amino]triphenylamine (2T-NATA) (25 nm)/N,N''-Di-[(1-naphthyl)-N,N''-diphenyl]-1,1''-biphenyl-4,4''-diamine (NPB) (40 nm)/tris-(8-hydroxyquinoline) aluminum (Alq3) (50 nm)/LiF (1 nm)/Al:Ag (1:3) (x), where the thicknesses of cathode metal layers (Al:Ag) are adjusted, respectively, from 70 nm to 100 nm. In the experiment, it is found that the LiF (1 nm)/Al:Ag (1:3) (75 nm) has good electron injection efficiency. Compared with an Al-only cathode, the turn-on voltage is lowered. At the voltage of 10 V, the luminances for bottom emission from ITO anode side and top emission from metal cathode side are 2 459 cd/m2 and 1 729 cd/m2, respectively. Thanks to electron injection enhancement by using Al:Ag cathode, we can obtain a better energy level matching between the cathode and the organic layer, thus the devices have lower turn-on voltage and higher luminance. The total transmittance of the devices can achieve about 40% at the wavelength of 550 nm.     

Electronic structures of CuI interlayers in organic electronic devices: An interfacial studies of N,N′-diphenyl-N,N′-bis(1-naphthyl)-1,1′-biphenyl-4,4′-diamine/CuI and tris-(8-hydroxyquinolinato)aluminum/CuI

Electronic structures with the copper iodide (CuI) interlayer in organic electronic devices were measured and its strong electron-withdrawing properties were revealed. In situ ultraviolet and X-ray photoelectron spectroscopy showed the interfacial electronic structures of N,N′-diphenyl-N,N′-bis(1-naphthyl)-1,1′-biphenyl-4,4′-diamine (NPB)/CuI/indium–tin-oxide (ITO) and tris-(8-hydroxyquinolinato)aluminum (Alq₃)/CuI/ITO as a representative hole- and electron-transport material. The large work function of the CuI interlayer induces electron transfer from both molecules and ITO to CuI. As a result, CuI dramatically reduces the hole injection barrier (HIB) from ITO to NPB and Alq₃ layers. Notably, CuI assists molecular ordering of the NPB layer, which would increase the intermolecular interaction, so would enhance the charge transport properties. Simultaneous enhancement in HIB and molecular ordering with the CuI interlayer would improve the device performance.     

Efficient blue emitters based on 1,3,5-triazine for nondoped organic light emitting diode applications

Two novel efficient blue emitters (TTT-1, TTT-2) containing 1,3,5-triazine, thiophene and triphenylamine have been designed and synthesized. Organic light emitting diodes (OLEDs) using these new triazine derivatives as emissive layers, ITO/TAPC (60 nm)/TTT-1 (Device A) or TTT-2 (Device B) (40 nm)/TPBi (60 nm)/LiF (1 nm)/Al (100 nm), were fabricated and tested. The OLEDs exhibited good performances with low turn-on voltage of 3 V, maximum luminance of ca. 8990 cd/m² for TTT-1 and 15,980 cd/m² for TTT-2, and maximum luminance efficiency of 4.7 cd/A for TTT-1 and 4.0 cd/A for TTT-2, respectively.     

MgF2缓冲层对蓝光OLED性能的影响

为了提高蓝光有机电致发光器件(OLED)的发光性能,将MgF2缓冲层插入ITO阳极与空穴传输层NPB之间,通过优化MgF2的厚度,制备了结构为ITO/MgF2(x nm)/NPB(50nm)/DPVBi:DSA-ph(30nm)/Alq3(30nm)/LiF(0.6nm)/Al(100nm)的高性能蓝光器件。实验结果表明,MgF2厚为1.0nm时,器件性能最佳,对应的器件最大电流效率达到5.51cd/A,最大亮度为23 290cd/m2(10.5V),与没有MgF2缓冲层的标准器件相比,分别提高47.3%和25.2%。对ITO表面的功函数测量结果表明,MgF2缓冲层可以有效修饰ITO表面,降低ITO与NPB之间的势垒高度差,改善空穴的注入效率,从而导致电子和空穴的注入更加平衡,激发机制更高效,实现了高性能的蓝光发射,为实现高效而稳定的全彩显示和白光照明奠定了基础。     

White organic light-emitting diodes based on emission from DPVBi-doped 4,48-bis (2,28-diphenylvinyl)-1, 18-biphenyl

Organiclight-emitting diodes (OLEDs) have beenin-vestigated for many years on account of their highlumi-nance,low driven voltages ,wide visual range,flexiblesubstratesinflat-panel ,full color displays and backlightapplications .For high brightness and eff…     

Low sublimation temperature cesium pivalate complex as an efficient electron injection material for organic light-emitting diode devices

Cesium pivalate ((CH₃)₃CCOOCs) has been synthesized and applied as an electron injection material for organic light-emitting diodes, which showed low sublimation temperature of 180 °C. Typical bilayer structure of ITO/NPB (60 nm)/Alq₃ (50 nm)/EIL/Al was used to evaluate the electron injection efficacy of (CH₃)₃CCOOCs, the results showed (CH₃)₃CCOOCs/Al exhibits better electron injection than LiF/Al cathode and the power efficiency was improved by about 19% at current density of 50 mA/cm². More interestingly, in the typical three layer OLED structure ITO/2-TNATA (60 nm)/NPB (10 nm)/Alq₃:2% C545T (40 nm)/MADN (15 nm)/(CH₃)₃CCOOCs (2 nm)/Al, the maximum current efficiency is up to 20 cd/A with Commission Internationale d’Eclairage (CIE_x,_y) color coordinates of (x = 0.30, y = 0.65) at current density of 140 mA/cm², which indicates that the non-aromatic alkali metal complex can also have good match with the chemically stable compound and exhibit good electron injection properties.     

CdS薄层对有机电致发光器件性能的影响

将光电材料硫化镉(CdS)薄层插入到结构为ITO/NPB/Rubrene/NPB/DPVBi/Alq3/LiF/Al的白光有机发光器件(OLED)的Alq3和LiF之间,研究了CdS对OLED性能的影响。结果表明,0.1nm厚的CdS插入Alq3和LiF之间的器件性能最好。器件电压从7 V变化到14 V时,色度均在白光的中心区域;当电压为7V时,器件的最大电流效率为9.09cd/A;当电压为14V时,器件的最大亮度为16 370cd/m2。不加CdS时,当电压为8V时,器件的最大效率为5.16cd/A;当电压为14V时,最大亮度为6 669cd/m2。加CdS的器件比不加CdS的器件最大效率提高了1.76倍,最大亮度提高了2.42倍。     

Pure‐Red Dye for Organic Electroluminescent Devices: Bis‐Condensed DCM Derivatives

In this paper, the bis‐condensed 4‐(dicyanomethylene)‐2‐methyl‐6‐[p‐(dimethylamino)styryl]‐4H‐pyran ( DCM) derivatives are introduced as a new class of red dye for organic light‐emitting devices (OLEDs). They showed more red‐shifted emission than the mono‐substituted DCM derivatives and the emission maxima increased as the electron‐donating ability of the aromatic donor group increased. On the basis of these results, red light‐emitting devices were fabricated with bis‐condensed DCM derivatives as red dopants. For a device of configuration ITO/TPD/Alq₃ + DADB (5.2 wt.‐%)/Alq₃/Al (where ITO is indium tin oxide, TPD is N,N′‐diphenyl‐N,N′‐bis(3‐methylphenyl)‐1,1′‐biphenyl‐4,4′‐diamine, Alq₃ is tris(8‐hydroxyquinoline) aluminum, and DADB is [2,6‐bis[2‐[5‐(dibutylamino)phenyl]vinyl]‐4H‐pyran‐4‐ylidene]propanedinitrile), pure red emission was observed with Commission Internationale de l’Eclairage (CIE 1931) coordinates of (0.658, 0.337) at 25 mA/cm².     

High‐Purity‐Blue and High‐Efficiency Electroluminescent Devices Based on Anthracene

Novel blue‐light‐emitting materials, 9,10‐bis(1,2‐diphenyl styryl)anthracene (BDSA) and 9,10‐bis(4′‐triphenylsilylphenyl)anthracene (BTSA), which are composed of an anthracene molecule as the main unit and a rigid and bulky 1,2‐diphenylstyryl or triphenylsilylphenyl side unit, have been designed and synthesized. Theoretical calculations on the three‐dimensional structures of BDSA and BTSA show that they have a non‐coplanar structure and inhibited intermolecular interactions, resulting in a high luminescence efficiency and good color purity. By incorporating these new, non‐doped, blue‐light‐emitting materials into a multilayer device structure, it is possible to achieve luminance efficiencies of 1.43 lm W^–1 (3.0 cd A^–1 at 6.6 V) for BDSA and 0.61 lm W^–1 (1.3 cd A^–1 at 6.7 V) for BTSA at 10 mA cm^–2. The electroluminescence spectrum of the indium tin oxide (ITO)/copper phthalocyanine (CuPc)/1,4‐bis[(1‐naphthylphenyl)‐amino]biphenyl (α‐NPD)/BDSA/tris(9‐hydroxyquinolinato)aluminum (Alq₃)/LiF/Al device shows a narrow emission band with a full width at half maximum (FWHM) of 55 nm and a λ_max = 453 nm. The FWHM of the ITO/CuPc/α‐NPD/BTSA/Alq₃/LiF/Al device is 53 nm, with a λ_max = 436 nm. Regarding color, the devices showed highly pure blue emission ((x,y) = (0.15,0.09) for BTSA, (x,y) = (0.14,0.10) for BDSA) at 10 mA cm^–2 in Commission Internationale de l'Eclairage (CIE) chromaticity coordinates.     

To observe bidirectional negative differential resistance at room temperature by narrowing transport channels for charge carriers in vertical organic light-emitting transistor

Bidirectional negative differential resistance (NDR) at room temperature with high peak-to-valley current ratio (PVCR) of ～10 are observed from vertical organic light-emitting transistor indium-tin oxide (ITO)/N,N′-di(naphthalene-1-yl)-N,N′-diphenyl-benzidine) (α-NPD)(60 nm)/Al(30 nm)/α-NPD(60 nm)/tris-(8-hydroxyquinoline) aluminium (Alq₃)(50 nm)/Al by narrowing the transport channels for charge carriers with a thick-enough middle Al gate electrode layer to block charge carriers transporting from source electrode to drain electrode. When the transport channel for charge carriers gets large enough, the controllability of gate bias on the drain–source current gets weaker and the device almost works as an organic light-emitting diode only. Therefore, it provides a very simple way to produce NDR device with dominant bidirectional NDR and high PVCR (～10) at room temperature by narrowing transport channels for charge carriers in optoelectronics.