Ionic outgassing from photoacid generators upon irradiation at 13.5 nm

Photoresist outgassing is considered a possible source of contamination of optics in extreme ultraviolet (EUV) lithography at 13.5 nm. We measured the relative proportions of ionic outgassing from 18 commercially available photoacid generators (PAG), which is a key component of chemically amplified photoresists, upon irradiation at 13.5 nm. These PAG include 17 triarylsulfonium or diaryliodonium salts, which contain or as the anion, and one PAG of molecular type. The overall outgassed ions in the range 10-200 u were counted in relative proportions. Outgassing of F⁺ is found to be dominant, and for most PAG the extent of F⁺ outgassing shows a satisfactory correlation with the ratio of F atomic photoabsorption to the overall PAG photoabsorption. Outgassed ions F⁺, CF⁺, and from PAG containing the anion and additional such as , and from those containing are identified. Triphenylsulfonium perfluoro-1-butanesulfonate is one PAG to emit the most abundant F⁺ and total ionic fragments, and a PAG of molecular type (N-hydroxy-5-norbornene-2,3-dicarboximide perfluoro-1-butanesulfonate) also emits abundantly both hydrocarbon ions and F⁺. Ionic outgassing of PAG cations includes (C₆H₅)₂S⁺ from R(C₆H₅)₂S⁺ salts and I⁺ from diaryliodonium salts. For PAG containing t-C₄H₉, significantly less F⁺ outgassing is observed; additional outgassing pathways are proposed. The pressure rise caused by PAG shows no dependence on the anion identity, but is correlated with cation photoabsorption, and ascribed to neutral aryl outgassing. Other minor outgassing species include from sulfonates; and ‘photostable’ PAH cations are identified for the first time and provide evidence of concurrent outgassing from, and polymerization of, PAG upon irradiation at 13.5 nm.     

Low-voltage nanopower clock generator for RFID applications

The design of an on-chip RC-based oscillator, implemented in a standard BiCMOS process, without any external component, is presented. The proposed oscillator provides a clock signal at a frequency of 50 kHz with a temperature coefficient smaller than 0.3%/^°C over a temperature range from 0 to , without any external trimming. The proposed oscillator operates with a supply voltage of 0.8 V and has a power consumption of at room temperature. The chip area is .     

A 1-V RF-CMOS LNA design utilizing the technique of capacitive feedback matching network

In this paper, a CMOS low-noise amplifier (LNA) with a new input matching topology has been proposed, analyzed and measured. The input matching network is designed through the technique of capacitive feedback matching network. The proposed LNA which is implemented in a technology is operated at the frequency of 12.8 GHz. It has a gain S21 of 13.2 dB, a noise figure (NF) of 4.57 dB and an NF_min of 4.46 dB. The reverse isolation S12 of the LNA can achieve and the input and output return losses are better than . The input 1-dB compression point is and IIP3 is . This LNA drains 10 mA from the supply voltage of 1 V.     

High-mobility pentacene thin-film transistors with copolymer-gate dielectric

Pentacene thin-film transistors have been obtained using polymethyl-methacrylate-co-glyciclyl-methacrylate (PMMA-GMA) as the gate dielectric. The optimum active layer thickness in thin-film transistors (OTFTs) was investigated. The present devices show a wide operation voltage range. The on/off current ratio is as high as 10⁵. In linear region (), the field-effect mobility of device increases with the increase in gate field at low-voltage region (), and a mobility of 0.33 cm²/V s can be obtained when . In saturation region, the mobility increases linearly with the gate field, and a high mobility of 1.14 cm²/V s can be obtained at . The influence of voltage on mobility of device was investigated.     

Properties of wurtzite GaN MESFETs studied by two-dimensional full band Monte Carlo approach

The properties of a GaN Metal-Semiconductor Field Effect Transistor were studied based on two-dimensional full band Monte Carlo simulations. The dependences of the distributions of the electric potential, electron concentration, electric field, drift velocity, and average electron energy on the gate-source voltage (V_GS) and drain-source voltage (V_DS) were obtained, then the characteristics of the drain current (I_DS) versus the drain-source voltage (V_DS) and the transconductance (G_m) versus V_GS characteristics were determined. At and I_DS is 5.03 A/cm, which is higher value. The G_m−V_GS curve shows bell shaped and the maximum G_m is 112 ms/mm at and The current gain cutoff frequency (f_T) is 98 GHz at and      

YBCO superconducting tapes by melt-annealing method on metallic Ni%5W substrates

Superconducting tapes of YBCO-123 were produced by melt-annealing method on metallic Ni%5W substrates. YBCO thick films of about thick were deposited on Ni%5W tapes previously CeO₂ coated using different thermal treatments. A final architecture of the tapes like Ni%5W/CeO₂/YBCO/Au-Pd was achieved.Critical temperatures (T_c) of the superconducting tapes around 89 K and critical current densities (J_c) of at 77 K and were determined by resistive methods. All the samples displayed a granular character and the crystalline structure of the superconducting YBCO-123 with and preferential orientation along the c-axis as determined by SEM and XRD analysis, respectively. Both grain sizes and c-axis orientation are dependent of the thermal treatments.     

Numerical optimization of an extracted HgCdTe IR-photodiodes for 10.6-μm spectral region operating at room temperature

The electrical and photoelectrical properties of long wavelength Hg_1−xCd_xTe structures have been optimized by using an exact numerical analysis. In this analysis we have been taking into account the degeneracy, non-parabolicty, deviation from thermodynamical equilibrium and graded interfaces. The band diagram, electrical field, carrier mobility, photoelectrical gain, responsivity, noise and detectivity have been calculated and optimized as a function of different variable such as alloy composition, doping concentration, thickness, and applied voltage to obtain optimized performance at room temperature. This numerical simulation can be used to optimize the mentioned parameters for other structures such as , operating in photodiode, or photovoltaic mode.     

A high precision low dropout regulator with nested feedback loops

A high precision low dropout regulator (LDO) with nested feedback loops is proposed in this paper. By nesting a zero-tracking compensation loop inside of the negative feedback loop comprising an error amplifier, the independence of off-chip capacitor and effective series resistance (ESR) is ensured for different load currents and operating voltages. This circuit is designed and fabricated using a standard CMOS process. The die area is a . The measurement results show that the total error of the output voltage caused by line and load variations is less than ±3% in low quiescent current (Iddq) or low voltage scenarios. Besides, the smallest dropout of the LDO, 0.11 V, while the output current is 165 mA, the output load is and 20 in parallel.     

Low power impedance measurement integrated circuit for sensor applications

In this paper an integrated circuit for the measurement of the real and imaginary part of an impedance is presented. The circuit is intended for its use in a wireless integrated system. A mixed analog/digital approach has been adopted in order to minimize power and area requirements, as requested by the application. The four electrode configuration is used for impedance measurement using two excitation current sources and a buffer instead of an instrumentation amplifier, therefore reducing the circuit complexity. The digital block controls the working frequency and can compensate the phase error introduced by the analog filters, thereby reducing the total error in the measurement. The integrated circuit has been designed in a CMOS process and it works with 3.3 V with a power consumption of . Experimental results to verify its functionality are presented.     

Self-aligned In0.49Ga0.51P/GaAs HBT DC and RF characteristics related with orientations

A self-aligned InGaP/GaAs HBT DC and RF characteristics related with orientations were studied. The DC current gain was greater for the [0 1 1] emitter orientation compared to orientation. However, it also showed slightly better RF performance for orientation with a cutoff frequency f_T 69 GHz compared to the f_T of 62 GHz for the [0 1 1] orientation. This experimental work has been proposed that the dependence of the characteristics could be attributed to both piezoelectric effect and the difference between lateral etched profiles in different directions.