Degradation characteristics of polylactide in thermophilic anaerobic digestion with hyperthermophilic solubilization condition

To test whether hyperthermophilic treatment promotes polylactide (PLA) dissolution and methane conversion under anaerobic digestion conditions, a single thermophilic control reactor (55 °C) and a two-phase system consisting of a hyperthermophilic reactor (80 °C) and a thermophilic reactor (55 °C) were continuously fed with a mixture of PLA and artificial kitchen garbage. In Runs 1 and 2, the PLA dissolution ratios in the two-phase system were 79.2 ± 6.5% and 85.2 ± 7.0%, respectively, higher than those of the control. Batch experimental results indicated that hyperthermophilic treatment could promote PLA dissolution to a greater degree as compared with single thermophilic treatment and that ammonia addition also had a promotional effect on PLA dissolution. In the two-phase system, after hyperthermophilic treatment, dissolved PLA was converted to methane gas under the subsequent thermophilic condition.     

Treatment of dye works wastewater using anaerobic-oxic biological filter reactor packed with carbon fibre and aerated with micro-bubbles.

A new anaerobic-oxic biological filter reactor, which was packed with carbon fibre and aerated with micro-bubbles, was proposed. The reactor performance was examined using dye works wastewater compared with the activated sludge reactor. Effluent SS from the experimental reactor was significantly lower than that from the activated sludge reactor, and transparency was higher. Temperatures of the activated sludge reactor were over 35 degrees C and DOC removal ratios were 40-80% depending on the influent wastewater. On the other hand, the DOC removal efficiency of the experimental reactor was over 70%, when the reactor temperature was over 22 degrees C. In the anaerobic zone, sulphate reduction occurred predominantly and acetate was produced. In the oxic reactor, sulphur oxidation and organic removal occurred. When the amount of sulphate reduction in the anaerobic zone increased, DOC and colour in effluent decreased. The sulphate reducing activity of biofilm at 30 degrees C was three times higher than those at 20 degrees C. The sulphate reducing activity of biofilm in the oxic zone was higher than those in the anaerobic zone, meaning that the sulphate reduction-oxidation cycles were established in the biofilm of the oxic zone. Microbial community of sulphate reducing bacteria was examined by in situ hybridisation with 16S rRNA targeted oligonucleotide probes. Desulfobulbus spp. was most common sulphate reducing bacteria in the anaerobic zone. In the oxic zone, Desulfobulbus spp. and Desulfococcus spp. were observed.     

Real-time quantifications of dominant anaerobes in an upflow reactor by polymerase chain reaction using a TaqMan probe.

This study was conducted to demonstrate the application of quantitative real-time polymerase chain reaction (qRT-PCR) for the quantification of dominant bacteria in an anaerobic reactor using a designed TaqMan probe. A novel group of uncultured thermophilic bacteria affiliated with Thermotogales was first found in a phenol-degrading sludge from a 55 degrees C upflow anaerobic sludge blanket (UASB) reactor, which effectively removed 99% of phenol at loading of 0.51 g-phenol l(-1) d(-1) h of hydraulic retention. A TaqMan probe was then designed targeting this group of Thermotogales affiliated bacteria (TAB), and used to monitor its concentration in the reactors. Results showed that the TAB population in the 55 degrees C reactor increased proportional to the phenol degrading rate. Results also showed that the TAB population ranged 3.5-9.9% in the 55 degrees C phenol-degrading sludge, but only 0.0044% in the 37 degrees C sludge and 0.000086% in the 26 degrees C sludge.     

Anaerobic digestion elutriated phased treatment of piggery waste.

The performance of a novel high-rate anaerobic process, the anaerobic digestion elutriated phased treatment (ADEPT) process, for treating a slurry-type piggery waste (55 g COD/L and 37 g TS/L) was investigated. The ADEPT process consists of an acid elutriation slurry reactor for hydrolysis and acidification, followed by an upflow anaerobic sludge bed reactor for methanification. This process provides stable and high system performance with short HRT (7.4 d) and better effluent quality (2 g SCOD/L and 0.68 g VSS/L) due to the alkaline pH condition for hydrolysis/acidification phase, high refractory solids removal and ammonia toxicity reduction. The optimum pH and HRT for hydrolysis/acidogenesis of the piggery waste were 9 and 5 days at both 35 degrees C and 55 degrees C conditions. The hydrolysis and acidification rate in the mesophilic reactor were 0.05 d(-1) and 0.11 d(-1), meaning that hydrolysis was a limiting step. SCOD production by the hydrolysis was about 0.26 g SCOD/g VS(fed) (3.6 g SCOD/g VS reduction). Methane production and content in the system were 0.3 L CH4/g VS(fed) (0.67 L CH4/g VS destroyed) and 80%, respectively, corresponding to 0.23 L CH4/g COD removal (@STP).     

Grey water treatment in upflow anaerobic sludge blanket (UASB) reactor at different temperatures

The treatment of grey water in two upflow anaerobic sludge blanket (UASB) reactors, operated at different hydraulic retention times (HRTs) and temperatures, was investigated. The first reactor (UASB-A) was operated at ambient temperature (14-25 degrees C) and HRT of 20, 12 and 8 h, while the second reactor (UASB-30) was operated at controlled temperature of 30 degrees C and HRT of 16, 10 and 6 h. The two reactors were fed with grey water from 'Flintenbreite' settlement in Luebeck, Germany. When the grey water was treated in the UASB reactor at 30 degrees C, total chemical oxygen demand (CODt) removal of 52-64% was achieved at HRT between 6 and 16 h, while at lower temperature lower removal (31-41%) was obtained at HRT between 8 and 20 h. Total nitrogen and phosphorous removal in the UASB reactors were limited (22-36 and 10-24%, respectively) at all operational conditions. The results showed that at increasing temperature or decreasing HRT of the reactors, maximum specific methanogenic activity of the sludge in the reactors improved. As the UASB reactor showed a significantly higher COD removal (31-64%) than the septic tank (11-14%) even at low temperature, it is recommended to use UASB reactor instead of septic tank (the most common system) for grey water pre-treatment. Based on the achieved results and due to high peak flow factor, a HRT between 8 and 12 h can be considered the suitable HRT for the UASB reactor treating grey water at temperature 20-30 degrees C, while a HRT of 12-24 h can be applied at temperature lower than 20 degrees C.     

UASB reactor for domestic wastewater treatment at low temperatures: a comparison between a classical UASB and hybrid UASB-filter reactor.

The performance of an upflow anaerobic sludge blanket (UASB) reactor and a hybrid UASB-filter reactor was investigated and compared for the treatment of domestic wastewater at different operational temperatures (28, 20, 14 and 10 degrees C) and loading rates. For each temperature studied a constant CODt removal was observed as long as the upflow velocity was lower than 0.35 m/h. At these upflow velocities similar removals were observed for both reactor types at 28 and 20 degrees C, 82 and 72% respectively. However, at 14 and 10 degrees C the UASB reactor showed a better COD removal (70% and 48%, respectively) than the hybrid reactor (60% and 38%). COD removal resulted from biological degradation and solids accumulation in the reactors. At 28 degrees C, a constant 200 g sludge mass was observed in both reactors and COD removal was attributed to biological degradation only. At lower temperatures, solids accumulation was observed in addition to biological degradation with an increase in reactor sludge as the temperature decreased. The decrease in biological degradation at lower temperatures was offset by solids accumulation and explains the similar overall COD removal efficiency observed at 28 degrees C, 20 degrees C and 14 degrees C. The decrease in temperature was also followed by an increase in the effluent TSS concentration in both reactors. At 14 and 10 degrees C a lower effluent TSS concentration and better performance was observed in the UASB reactor.     

Changes of microbial characteristics of retained sludge during low-temperature operation of an EGSB reactor for low-strength wastewater treatment.

In this study, a lab scale EGSB reactor was operated for 400 days to investigate the influence of temperature-decrease on the microbial characteristic of retained sludge. The EGSB reactor was started-up at 15 degrees C seeding with 20 degrees C-grown granular sludge. The influent COD of synthetic wastewater was set at 0.6-0.8 gCOD/L. The process-temperature was stepwise reduced from 15 degrees C to 5 degrees C during 400 days operation. Decrease of temperature of the reactor from 15 degrees C to 10 degrees C caused the decline of COD removal efficiency. However, continuous operation of the EGSB reactor led the efficient treatment of wastewater (70% of COD removal, 50% of methane recovery) at 10 degrees C. We confirmed that the both acetate-fed and hydrogen-fed methanogenic activities of retained sludge clearly increased under 15 to 20 degrees C. Changes of microbial profiles of methanogenic bacteria were analyzed by 16S rDNA-targeted DGGE analysis and cloning. It shows that genus Methanospirillum as hydrogen-utilizing methanogen proliferated due to low temperature operation of the reactor. On the other hand, genus Methanosaeta presented in abundance as acetoclastic-methanogen throughout the experiment.     

Anammox process for synthetic and practical wastewater treatment using a novel kind of biomass carriers

The anammox process, as an alternative to conventional nitrogen removal technologies, has abstracted much attention in recent years. In this study, one column-type reactor using a novel support material--net type acrylic fiber (Biofix)--was used for anammox treatment. The Biofix reactor was operated at 25 degrees C (peak summer temperature, 31.5 degrees C). Over 330 days of operation for synthetic wastewater treatment, the nitrogen loading rates of the reactor were increased to 3.6 kg-N/m3/d and T-N removal efficiencies reached to 81.3%. For the practical anaerobic sludge digester liquor treatment, the average TN removal efficiency of 72% was obtained. A protein substance was shown to be the most abundant extracellular polymeric substances (EPS) in the granular sludge with almost two times more in the attached sludge of the Biofix reactor. Considering the EPS levels and observation by scanning electron microscopy, the anammox granules in the Biofix reactor were showing dense state. Results of DNA analyses indicated that the KSU-1 strain might prefer relatively low nutrient levels, while the KU2 strain might be better suited for the high media concentration. Other kinds of bacteria were also identified with the potentials for consuming the dissolved oxygen in the influent and facilitating anammox bacteria surviving under aerobic conditions.     

Two-stage thermophilic-mesophilic anaerobic digestion of waste activated sludge from a biological nutrient removal plant.

A two-stage thermophilic-mesophilic anaerobic digestion pilot-plant was operated solely on waste activated sludge (WAS) from a biological nutrient removal (BNR) plant. The first-stage thermophilic reactor (HRT 2 days) was operated at 47, 54 and 60 degrees C. The second-stage mesophilic digester (HRT 15 days) was held at a constant temperature of 36-37 degrees C. For comparison with a single-stage mesophilic process, the mesophilic digester was also operated separately with an HRT of 17 days and temperature of 36-37 degrees C. The results showed a truly thermophilic stage (60 degrees C) was essential to achieve good WAS degradation. The lower thermophilic temperatures examined did not offer advantages over single-stage mesophilic treatment in terms of COD and VS removal. At a thermophilic temperature of 60 degrees C, the plant achieved 35% VS reduction, representing a 46% increase compared to the single-stage mesophilic digester. This is a significant level of degradation which could make such a process viable in situations where there is no primary sludge generated. The fate of the biologically stored phosphorus in this BNR sludge was also investigated. Over 80% of the incoming phosphorus remained bound up with the solids and was not released into solution during the WAS digestion. Therefore only a small fraction of phosphorus would be recycled to the main treatment plant with the dewatering stream.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Adapting UASB technology for sewage treatment in Palestine and Jordan.

High rate anaerobic technologies offer cost-effective solutions for "sewage" treatment in the temperate climate of Palestine and Jordan. However, local sewage characteristics demand amendments to the conventional UASB reactor design. A solution is found in a parallel operating digester unit that stabilises incoming solids and enriches the UASB sludge bed with methanogenic activity. The digester operational conditions were assessed by operating eight CSTRs fed with primary sludge. The results showed a high degree of sludge stabilization in the parallel digesters at SRTs>or=10 and 15 days at process temperatures of 35 and 25 degrees C, respectively. The technical feasibility of the UASB-digester combination was demonstrated by continuous flow pilot-scale experiments. A pilot UASB reactor was operated for 81 days at 6 hours HRT and 15 degrees C and was fed with raw domestic sewage. This period was subsequently followed by an 83 day operation period incorporating a parallel digester unit, which was operated at 35 degrees C. The UASB-digester combination achieved removal efficiencies of total, suspended, colloidal and dissolved CODs of respectively 66, 87, 44 and 30%. Preliminary model calculations indicated that a total reactor volume of the UASB-digester system corresponding to 8.6 hours HRT might suffice for sewage treatment in Palestine.     

Pilot-scale studies on biological treatment of hypersaline wastewater at low temperature.

In order to investigate the feasibility of biological treatment of hypersaline wastewater produced from toilet flushing with seawater at low temperature, pilot-scale studies were established with plug-flow activated sludge process at low temperature (5-9 degrees C) based on bench-scale experiments. The critical salinity concentration of 30 g/L, which resulted from the cooperation results of the non-halophilic bacteria and the halophilic bacteria, was drawn in bench-scale experiments. Pilot-scale studies showed that high COD removal efficiency, higher than 80%, was obtained at low temperature when 30 percent seawater was introduced. The salinity improved the settleability of activated sludge, and average sludge value dropped down from 38% to 22.5% after adding seawater. Seawater salinity had a strong negative effect on notronomonas and nitrobacter growth, but much more on the nitrobacter. The nitrification action was mainly accomplished by nitrosomonas. Bench-scale experiments using two SBRs were carried out for further investigation under different conditions of salinities, ammonia loadings and temperatures. Biological nitrogen removal via nitrite pathway from wastewater containing 30 percent seawater was achieved, but the ammonia removal efficiency was strongly related not only to the influent ammonia loading at different salinities but also to temperature. When the ratio of seawater to wastewater was 30 percent, and the ammonia loading was below the critical value of 0.15 kgNH4+-N/(kgMLSS.d), the ammonia removal efficiency via nitrite pathway was above 90%. The critical level of ammonia loading was 0.15, 0.08 and 0.03 kgNH4+-N/(kgMLSS.d) respectively at the different temperature 30 degrees C, 25 degrees C and 20 degrees C when the influent ammonia concentration was 60-80 mg/L and pH was 7.5-8.0.     

The effect of temperature and sludge age on COD removal and nitrification in a moving bed sequencing batch biofilm reactor.

This study investigates the effect of temperature and the sludge age on the performance of a moving bed sequencing batch biofilm reactor (MBSBBR) for COD removal and nitrification. The experiments are conducted in a lab-scale MBSBBR operated at three different temperatures (20, 15 and 10 degrees C) with a synthetic feed simulating domestic sewage characteristics. Evaluation of the results revealed that removal of organic matter at high rates and with efficiencies over 90% was secured at all operation conditions applied. The nitrification rate was significantly influenced by changes in temperature but complete nitrification occurred at each temperature. The nitrification rates observed at 20 and 15 degrees C were very close (0.241 mg NO(x)-N/m2d, 0.252 mg NO(x)-N/m2 d, respectively), but at 10 degrees C, it decreased to 0.178 mg NO(x)-N/m2d. On the other hand, the biomass concentration and sludge age increased while the VSS/TSS ratios that can be accepted as an indicator of active biomass fraction decreased with time. It is considered that, increasing biofilm thickness and diffusion limitation affected the treatment efficiency, especially nitrification rate, negatively.     

Grey water treatment in UASB reactor at ambient temperature.

In this paper, the feasibility of grey water treatment in a UASB reactor was investigated. The batch recirculation experiments showed that a maximum total-COD removal of 79% can be obtained in grey-water treatment in the UASB reactor. The continuous operational results of a UASB reactor treating grey water at different hydraulic retention time (HRT) of 20, 12 and 8 hours at ambient temperature (14-24 degrees C) showed that 31-41% of total COD was removed. These results were significantly higher than that achieved by a septic tank (11-14%), the most common system for grey water pre-treatment, at HRT of 2-3 days. The relatively lower removal of total COD in the UASB reactor was mainly due to a higher amount of colloidal COD in the grey water, as compared to that reported in domestic wastewater. The grey water had a limited amount of nitrogen, which was mainly in particulate form (80-90%). The UASB reactor removed 24-36% and 10-24% of total nitrogen and total phosphorus, respectively, in the grey water, due to particulate nutrients removal by physical entrapment and sedimentation. The sludge characteristics of the UASB reactor showed that the system had stable performance and the recommended HRT for the reactor is 12 hours.     

Anaerobic ammonium oxidation of ammonium-rich waste streams in fixed-bed reactors.

The feasibility of anaerobic ammonium oxidation (Anammox) in fixed-bed reactors was evaluated on laboratory and pilot scales. Using synthetic wastewater, the specific nitrogen removal rate was increased from 0.05-0.1 kgNm(-3)(reactor)d(-1) to 0.35-0.38 kgNm(-3)(reactor)d(-1) within a year (T= 22-27 degrees C) in all applications. However, the anammox activity was seriously and repeatedly inhibited at prolonged high nitrite concentrations (e.g. six days at 30-50 gNO2-Nm(-3)) and recovery was always a lengthy process. But even at a moderate nitrite concentration (11+/-10 gNO2-Nm(-3)), the observed specific growth rate was only 0.018 d(-1) at 26.4+/-0.8 degrees C, which corresponds to approximately 0.025 d(-1) at 30 degrees C (doubling time: 28 days). In a second experimental period for another 250 days, one of the laboratory reactors was fed with partially nitrified sludge liquors from a domestic wastewater treatment plant (WWTP). In this case, the specific elimination rate was as high as 3.5 kgNm(-3)(reactor)d(-1) at 26-27 degrees C. Independently of the feed, the average nitrogen elimination rate lay between 80-85% in all applications. An appropriate hydraulic design is essential to prevent clogging and local nitrite inhibition in fixed-bed reactors.     

Low strength wastewater treatment under low temperature conditions by a novel sulfur redox action process.

The objective of this research is to make a novel wastewater treatment process activated by a sulfur-redox cycle action of microbes in low temperature conditions. This action is carried out by sulfate-reducing bacteria (SRB) and sulfur-oxidizing bacteria (SOB). The process was comprised of a UASB reactor as pre-treatment and an aerobic downflow hanging sponge (DHS) reactor as post-treatment. As the results of reactor operation, the whole process achieved that over 90% of CODcr removal efficiency, less than 30 mgCODcr/L (less than 15 mgBOD/L) of final effluent, at 12 h of HRT and at 8 degrees C of UASB reactor temperature. Acetobacterium sp. was detected as the predominant species by PCR-DGGE method targeting 16SrDNA with band excision and sequence analysis. In the UASB reactor, various species of sulfate-reducing bacterium, Desulfobulbus sp., Desulfovibrio sp., and Desulfomicrobium sp., were found by cloning analysis. In the DHS reactor, Tetracoccus sp. presented as dominant. The proposed sulfur-redox action process was considered as an applicable process for low strength wastewater treatment in low temperature conditions.     

Enhanced primary treatment of concentrated black water and kitchen residues within DESAR concept using two types of anaerobic digesters.

Anaerobic digestion of concentrated domestic wastewater streams--black or brown water, and solid fraction of kitchen waste is considered as a core technology in a source separation based sanitation concept (DESAR--decentralised sanitation and reuse). A simple anaerobic digester can be implemented for an enhanced primary treatment or, in some situations, as a main treatment. Two reactor configurations were extensively studied; accumulation system (AC) and UASB septic tank at 15, 20 and 25 degrees C. Due to long retention times in an AC reactor, far stabilisation of treated medium can be accomplished with methanisation up to 60%. The AC systems are the most suitable to apply when the volume of waste to be treated is minimal and when a direct reuse of a treated medium in agriculture is possible. Digested effluent contains both liquid and solids. In a UASB septic tank, efficient separation of solids and liquid is accomplished. The total COD removal was above 80% at 25 degrees C. The effluent contains COD and nutrients, mainly in a soluble form. The frequency of excess sludge removal is low and sludge is well stabilised due to a long accumulation time.     

Biological nutrient removal in simple dual sludge system with an UMBR (upflow multi-layer bioreactor) and aerobic biofilm reactor.

In this study, a simple dual sludge process was developed for small sewage treatment. It is a hybrid system that consists of upflow multi-layer bioreactor (UMBR) as anaerobic and anoxic reactor with suspended growth microorganisms and post aerobic biofilm reactor with inclined plates. UMBR is a multifunction reactor that acts as primary sedimentation tank, anaerobic reactor, anoxic reactor, and thickener. The sludge blanket in the UMBR is maintained at a constant level by automatic control so that clear water (30 mg-SS/L) can flow into the post aerobic biofilm reactor. It leads to improving performance of the biofilm reactor due to preventing of excess microbial attachment on the media surface and no requirment for a large clarifier caused by low solid loading. The HRT in the UMBR and the aerobic biofilm reactor were about 5.8 h and 6.4 h, respectively. The temperature in the reactor during this study varied from 12.5 degrees C to 28.3 degrees C. The results obtained from this study show that effluent concentrations of TCOD, TBOD, SS, TN, and TP were 29.7 mg/L, 6.0 mg/L, 10.3 mg/L, 12.0 mg/L, and 1.8 mg/L, which corresponded to a removal efficiency of 92.7%, 96.4%, 96.4%, 74.9%, and 76.5%, respectively. The sludge biomass index (SBI) of the excess sludge in the UMBR was about 0.55, which means that the sludge in the UMBR was sufficiently stabilized and may not require further treatment prior to disposal.     

Maize mono-digestion efficiency: results from laboratory tests

A laboratory experimental campaign was carried out in order to assess the optimal configuration for the anaerobic digestion of a mixture of sweet corn and ensiled maize. Batch hydrolysis tests were conducted at 35 and 55 °C and at four different particle sizes (2, 5, 20 and 50 mm) obtained by manual chopping and sieving. Chemical pre-treatment by 24 h incubation at various acid and alkaline pH was also considered for its potential to increase the maize methane yield. Results suggest that the hydrolytic phase proceeds significantly faster under thermophilic conditions. Significant differences in the solubilization rate were also observed when comparing coarse (20-50 mm) with fine (2-5 mm) particles, while 2 and 5 mm particles were solubilized at similar rates. No advantages from the chemical pre-treatment, in terms of solubilization efficiency and biomethanization potential were observed. According to these preliminary results, a two-stage semi-continuous laboratory plant consisting of a thermophilic hydrolytic reactor followed by a mesophilic methanogenic reactor was operated for 110 days. Steady state loading parameters were: influent concentration (maize mixture diluted in tap water) of 46 g VS/L, hydraulic retention time of 31 d, organic loading rate of 1.5 g VS/L/d. Alkalinity was dosed to the methanogenic reactor to avoid pH drops. Collected data allowed the average biodegradation efficiency to be estimated at around 60-65%.     

Alkaline and acid hydrolytic processes in aerobic and anaerobic sludges: effect on total EPS and fractions.

Sludge samples from an upflow anaerobic sludge blanket (UASB) reactor and four submerged aerated biofilters (BFs) of a wastewater treatment plant (1,000 inhab.) were processed at bench scale by alkaline and acid hydrolysis with the objective to evaluate the organic matter solubilization, volatile solids (VS) destruction and the effect of hydrolytic processes on the extracellular polymeric substances (EPS) fraction of the sludge samples. The results showed that alkaline hydrolysis of sludge samples treatment with 1.0% total solids (TS) using NaOH 20 meq L(-1) was more efficient on organic matter solubilization and VS destruction than acid hydrolysis. The EPS sludge content was also affected by the alkaline treatment of anaerobic sludge samples. The EPS concentrations (mg EPS/gVSS) on the anaerobic sludge after the alkaline treatment were significantly lowered according to sample height in the UASB reactor. Data indicated that the EPS sludge fraction is the main component affected by the alkaline hydrolytic process of anaerobic sludge samples.