Effect of MgO/La2O3 additives on sintering behavior and microwave dielectric properties of (Sr,Ca)TiO3-(Sm,Nd)AlO3 ceramics

The effect of MgO/La₂O₃ additives on phase composition, microstructures, sintering behavior, and microwave dielectric properties of 0.7(Sr_0.01Ca_0.99)TiO₃−0.3(Sm_0.75Nd_0.25)AlO₃ (7SCT-3SNA) ceramics prepared via conventional solid-state route were systematically investigated. MgO/La₂O₃ as additives showed no obvious influence on the phase composition of the 7SCT-3SNA ceramics and all the samples exhibited pure perovskite structures. The presence of MgO/La₂O₃ additives effectively reduced the sintering temperature of 7SCT-3SNA ceramics due to the formation of a liquid phase at a relatively low temperature during sintering progress. The 0.5 wt% MgO doped 7SCT-3SNA sample with 0.5 wt% of La₂O₃, sintered at 1320 °C for 4 h, was measured to show superior microwave dielectric properties, with an ε_r of 45.57, a Q×f value of 46205 GHz (at 5.5 GHz), and τ_f value of −0.32 ppm/°C, which showed dense and uniform microstructure as well as well-developed grain growth.     

Synthesis and microwave dielectric properties of BaO-Sm2O3-5TiO2 ceramics with NdAlO3 additions

BaO-Sm₂O₃-5TiO₂ (BST5) ceramics with NdAlO₃ additions of up to 15 wt% were produced with a solid state reaction method, and their structural and microwave dielectric properties were determined. Experimental results showed that NdAlO₃ neither merged nor altered the orthorhombic tungsten bronze structure of the main phase of the produced ceramics (except for a shrinkage in the crystal lattice), but it was segregated in distinct grains in the microstructure of the produced ceramics. However, the amount of NdAlO₃ strongly influenced the densification and the microstructure (i.e. grain shape and size) of the produced ceramics. Analysis of the experimental results suggests that the microstructural features can be correlated to the dielectric properties of these ceramics. Accordingly, the dielectric constant (ε_r) and the temperature coefficient of resonant frequency (τ_f) of the produced BLT5 ceramics can be tuned with the amount of NdAlO₃ additions and the sintering process parameters. The best dielectric properties were achieved for BaO-Sm₂O₃-5TiO₂ ceramics with 7.5% NdAlO₃ (ε_r=73.22, Q×f =10,300 GHz, and τ_f=−1.05 ppm/°C).     

Low sintering BaNd2Ti4O12 microwave ceramics prepared by CuO thin layer coated powder

Recently, BaO–Nd₂O₃–TiO₂ systems are widely studied for microwave applications because of their high dielectric constant and high quality factor. However, pure BaNd₂Ti₄O₁₂ ceramics without additives have to be sintered above 1300 °C to achieve densification. Copper oxide has been known as a good sintering aid for electronic ceramics and less reactive toward silver. We have introduced the CuO into BaNd₂Ti₄O₁₂ by modifying the surface of BaNd₂Ti₄O₁₂ by CuO thin layer on the calcined powder instead of mixing CuO directly with BaNd₂Ti₄O₁₂ powder. The process reduces the amount of sintering aid and minimized the negative impact of sintering aid on dielectric properties such as quality factor. The CuO precursor solution of Cu(CH₃COO)₂, Cu(NO₃)₂ and CuSO₄, were used to prepare CuO thin layer. They were investigated individually to determine their effects on the densification, crystalline structure, microstructure and microwave dielectric properties of BaNd₂Ti₄O₁₂. The CuSO₄ coated BaNd₂Ti₄O₁₂ sintered at 1150 °C has exhibited better dielectric properties than those of CuO doped BaNd₂Ti₄O₁₂ (k, 62.5 versus 61.2; Q × f, 11,500 GHz versus 10,500 GHz). The thin layer dopant coating process has been found to be a very effective way to lower ceramic sintering temperature without scarifying its dielectric properties.     

Microwave dielectric properties of YAG ceramics prepared by sintering pyrolysised nano-sized powders

YAG ceramics with good dielectric properties were prepared via a modified pyrolysis method, with yttrium nitrate as the yttrium source and combined aluminium sulphate and aluminium nitrate as aluminium sources, and subsequent sintering in a muffle furnace. The effects of the different aluminium sources on the powder characteristic and the impact of sintering temperature, sintering aids (TEOS) and additive (TiO₂) on the dielectric properties of the ceramics were studied. The results show that well-dispersed pure YAG nano-powders can be obtained after calcination at 1000 °C with an aluminium sulphate and aluminium nitrate molar ratio of 1.5:2. The relative density, permittivity (ε_r) and quality factor (Q×f) of the YAG ceramics increase with sintering temperature and TEOS addition. TiO₂ can greatly promote τ_f to near-zero but decreases Q×f. The relative density, ε_r, Q×f and τ_f of the YAG–1 wt% TEOS–1 wt% TiO₂ ceramic obtained at 1520 °C are 97.6%, 9.9, 71, 738 GHz and −30 ppm/°C, respectively.     

Temperature stable and high-Q microwave dielectric ceramics in the Li2Mg3−xCaxTiO6 system (x=0.00–0.18)

Microwave dielectric properties of Li₂Mg_3−xCa_xTiO₆ (x=0–0.18) ceramics were studied using a conventional solid-state route to find temperature stable and high Q microwave ceramics. As the calcination temperature was 500 °C, the Li₂TiO₃ phase with monoclinic rock salt structure in C2/c space group started to form. When the samples were calcined from 600 °C to 900 °C, the XRD patterns exhibited a remarkable chemical reaction between the MgO and Li₂TiO₃ phases, which eventually formed the Li₂Mg₃TiO₆ phase. The results indicated the Li₂Mg₃TiO₆and CaTiO₃ co-existed with each other and formed a stable composite system when the calcium content was added. The SEM photographs indicated that the pores caused by the Li evaporation could be effectively reduced due to the appearance of CaTiO₃. As x was increased from 0 to 0.18, the relative density was significantly improved due to the elimination of pores. As the Ca content increased, the dielectric constant (εr) increased from 14.8 to 20.6; the quality factor (Q×f) decreased from 148,713 GHz to 79,845 GHz, and the temperature coefficient of resonant frequency (τf) significantly increased from −42.4 to +10.8 ppm/°C due to the increased amount of CaTiO₃. Therefore, at x=0.12, the LMCxT ceramics sintered at 1280 °C for 6 h displayed excellent comprehensive properties of εr=17.8,Q×f=102,246 GHz and τf=−0.7 ppm/°C.     

Effect of dopants on synthesis of BaTi4O9 and Ba2Ti9O20 ceramics prepared by reaction-sintering process

The effect of dopants on BaTi₄O₉ (BT4) and Ba₂Ti₉O₂₀ (B2T9) ceramics by the reaction-sintering process was investigated. CuO addition is more effective in lowering the sintering temperature of BT4 and B2T9 ceramics. MnO₂ and CuO addition are effective to obtain temperature stable BT4 ceramics. With MnO₂ addition, Q × f of BT4 ceramics could be raised. ZrO₂ addition is effective to obtain B2T9 ceramics with higher dielectric constant. With CuO addition, τ_f of B2T9 ceramics shifted toward negative values and 0 ppm/°C could be obtained. Optimum properties in BT4 doped with MnO₂ of ɛ_r = 37.1, Q × f = 51,200 GHz (at 7 GHz) and τ_f = 0 ppm/°C and in B2T9 doped with ZrO₂ of ɛ_r = 37.9, Q × f = 39,700 GHz (at 7 GHz) and τ_f = 5.9 ppm/°C were obtained.     

Influence of TiO2 additive on sintering temperature and microwave dielectric properties of Mg0.90Ni0.1SiO3 ceramics

(1-x)Mg_0.90Ni_0.1SiO₃-xTiO₂ (x = 0, 0.01, 0.03, 0.05) ceramics were successfully formed by the conventional solid-state methods and characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS), and their microstructure and microwave dielectric properties systematically investigated. It was observed that when TiO₂ content increased from 0 to 5 wt%, the Q_uf_o of the sample decreased from 118,702 GHz to 101,307 GHz and increases the τ_f value from −10 ppm/°C to +3.14 ppm/°C accompanied by a notable lowering in the sintering temperature (125 °C). A good combination of microwave dielectric properties (ε_r ∼ 8.29, Q_uf_o ∼ 101,307 GHz and τ_f ∼ −2.98 ppm/°C) were achieved for Mg_0.90Ni_0.1SiO₃ containing 3 wt% of TiO₂ sintered at 1300 °C for 9 h which make this material of possible interest for millimeter wave applications.     

High Q dielectric resonator material with low dielectric constant for millimeter-wave applications

Al₂O₃TiO₂ ceramics has great promise as a dielectric resonator material for millimeter-wave use. The Al₂O₃TiO₂MnO system provides low dielectric constant and high quality factor (Q). TiO₂ and Al₂O₃ can compensate each other's temperature coefficient of resonant frequency. It is important to suppress the appearance of Al₂TiO₅ phase for obtaining high Q-value. In this study, dense Al₂O₃TiO₂ mixed ceramics without Al₂TiO₅ phase was synthesized by lowering the sintering temperature. The addition of MnO decreases the sintering temperature from 1400 to 1300 °C. In this temperature range, Al₂TiO₅ phase is hardly formed. X-ray powder diffraction (XRD) patterns show that the ceramics is composed of Al₂O₃ and TiO₂ phases only. Dense and well dispersed mixture of Al₂O₃ and TiO₂ grains is observed by scanning electron microscopy (SEM).The 0.9Al₂O₃0.1TiO₂ ceramics doped with 0.4 mol% of MnO has dielectric constant of 12.4, Q × f of 274,000 GHz at 76 GHz, and temperature coefficient of resonant frequency of +0.4 ppm/°C. The dielectric constant and the temperature coefficient of resonant frequency can be controlled by TiO₂ content. This ceramics is suitable for millimeter-wave applications because of its low dielectric constant, high Q-value, and small temperature coefficient of resonant frequency.     

Microwave dielectric properties of low-fired Li2MnO3 ceramics co-doped with LiF–TiO2

Li₂MnO₃ ceramics co-doped with 2 wt% LiF and x wt% TiO₂ (x=0, 3, 5, 7, 10) were prepared by solid-state reaction for low-temperature co-fired ceramics (LTCC) applications. The sintering temperatures of Li₂MnO₃ ceramics were successfully lowered to 925°C due to the formation of a LiF liquid phase. Their temperature stability was improved by doping with TiO₂. A typical Li₂MnO₃-2 wt% LiF-5 wt% TiO₂ sample with well-densified microstructures displayed optimum dielectric properties (ε_r=13.8, Q×f= 23,270 GHz, τ_f=1.2 ppm/°C). Such sample was compatible with Ag electrodes, which suggests suitability of the developed material for LTCC applications in wireless communication systems.     

Microwave dielectric properties and low-temperature sintering of Ba3Ti4Nb4O21 ceramics with B2O3 and CuO additions

The low sintering temperature and the good dielectric properties such as high dielectric constant (ɛ_r), high quality factor (Q × f) and small temperature coefficient of resonant frequency (τ_f) are required for the application of chip passive components in the wireless communication technologies. In the present study, the sintering behaviors and dielectric properties of Ba₃Ti₄Nb₄O₂₁ ceramics were investigated as a function of B₂O₃–CuO content. Ba₃Ti₄Nb₄O₂₁ ceramics with B₂O₃ or CuO addition could be sintered above 1100 °C. However, the additions of both B₂O₃ and CuO successfully reduced the sintering temperature of Ba₃Ti₄Nb₄O₂₁ ceramics from 1350 to 900 °C without detriment to the microwave dielectric properties. From the X-ray diffraction (XRD) studies, the sintering behaviors and the microwave dielectric properties of low-fired Ba₃Ti₄Nb₄O₂₁ ceramics were examined and discussed in the formation of the secondary phases. The Ba₃Ti₄Nb₄O₂₁ sample with 1 wt% B₂O₃ and 3 wt% CuO addition, sintered at 900 °C for 2 h, had the good dielectric properties: ɛ_r = 65, Q × f = 16,000 GHz and τ_f = 101 ppm/°C.     

Li4Mg3Ti2O9: A novel low-loss microwave dielectric ceramic for LTCC applications

Low-loss novel Li₄Mg₃Ti₂O₉ dielectric ceramics with rock-salt structure were prepared by a conventional solid-state route. The crystalline structure, chemical bond properties, infrared spectroscopy and microwave dielectric properties of the abovementioned system were initially investigated. It could be concluded from this work that the extrinsic factors such as sintering temperatures and grain sizes significantly affected the dielectric properties of Li₄Mg₃Ti₂O₉ at lower sintering temperatures, while the intrinsic factors like bond ionicity and lattice energy played a dominant role when the ceramics were densified at 1450 °C. In order to explore the origin of intrinsic characteristics, complex dielectric constants (ε^’ and ε^’’) were calculated by the infrared spectra, which indicated that the absorptions of phonon oscillation predominantly effected the polarization of the ceramics. The Li₄Mg₃Ti₂O₉ ceramics sintered at 1450 °C exhibited excellent properties of ε_r=15.97, Q·f=135,800 GHz and τ_f=−7.06 ppm/°C. In addition, certain amounts of lithium fluoride (LiF) were added to lower the sintering temperatures of matrix. The Li₄Mg₃Ti₂O₉−3 wt% LiF ceramics sintered at 900 °C possessed suitable dielectric properties of ε_r=15.17, Q·f =42,800 GHz and τ_f=−11.30 ppm/°C, which made such materials promising for low temperature co-fired ceramic applications (LTCC).     

Characterization and dielectric behavior of willemite and TiO2-doped willemite ceramics at millimeter-wave frequency

Willemite ceramics (Zn₂SiO₄) have been successfully prepared in the temperature range from 1280 to 1340 °C. It is found that willemite ceramics possess excellent millimeter-wave dielectric properties: a dielectric constant ɛ_r value of 6.6, a quality factor Q × f value of 219,000 GHz and a temperature coefficient of resonant frequency τ_f value of −61 ppm/°C. By adding TiO₂ with large positive τ_f value (450 ppm/°C), near zero τ_f value can be achieved in a wide sintering temperature range. With 11 wt% of TiO₂, an ɛ_r value of 9.3, a Q × f value of 113,000 GHz, and a τ_f value of 1.0 ppm/°C are obtained at 1250 °C. The relationships between microstructure and properties are also studied. Our results show that willemite with appropriate TiO₂ is an ideal temperature stable, low ɛ_r and high Q × f dielectric for millimeter-wave application.     

Structure and dielectric properties of novel low temperature co-fired Bi2O3-RE2O3-MoO3 (RE=Pr,Nd, Sm,and Yb) based microwave ceramics

Novel monoclinic Bi₂O₃-xRE₂O₃-yMoO₃ (RE=Pr, Nd, Sm, and Yb) based low temperature co-fired ceramics (LTCC) systems with high sintering density and low microwave dielectric loss are synthesized by conventional solid state reaction technique. The structure and dielectric properties of Bi₂O₃-xRE₂O₃-yMoO₃ ceramics are investigated. Dense BiNdMoO₆ ceramics sintered at 900 °C for 8 h in air have a low dielectric constant ε_r=~7.5, a high quality factor Q×f=~ 24, 800 GHz at 7.0 GHz, and τ_f=~−16 ppm/̊C. Especially, good chemical compatibility of BiNdMoO₆ with Ag electrodes is represented as well. In contrast, BiSmMoO₆ ceramics sintered at 1000 °C for 8 h show enhanced Q×f=~43, 700 GHz at 7.8 GHz with ε_r=~8.5 and τ_f=~−27 ppm/°C. Bi₂O₃-xRE₂O₃-yMoO₃ (RE=Pr, Nd, Sm, and Yb) based ceramics could be considered as promising microwave ceramics for LTCC applications.     

Temperature stability and high-Qf of low temperature firing Mg2SiO4–Li2TiO3 microwave dielectric ceramics

In this work, a series of low-temperature-firing (1−x)Mg₂SiO₄–xLi₂TiO₃–8 wt% LiF (x = 35–85 wt%) microwave dielectric ceramics was prepared through conventional solid state reaction. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses showed that the Li₂TiO₃ phase was transformed into cubic phase LiTiO₂ phase and secondary phase Li₂TiSiO₅. Partial substitution of Mg²⁺ ions for Ti³⁺ ions or Li⁺Ti³⁺ ions increased the cell volume of the LiTiO₂ phase. The dense microstructures were obtained in low Li₂TiO₃ content (x ≤ 65 wt%) samples sintered at 900 °C, whereas the small quantity of pores presented in high Li₂TiO₃ content (x ≥ 75 wt%) samples sintered at 900 °C and low Li₂TiO₃ content (x = 45 wt%) sintered at 850 and 950 °C. Samples at x = 45 wt% under sintering at 900 °C for 4 h showed excellent microwave dielectric properties of ε_r = 10.7, high Q × f = 237,400 GHz and near-zero τ_f = − 3.0 ppm/°C. The ceramic also exhibited excellent chemical compatibility with Ag. Thus, the fabricated material could be a possible candidate for low temperature co-fired ceramic (LTCC) applications.     

Effect of B2O3 and CuO additives on the sintering temperature and microwave dielectric properties of Ba(Zn1/3Nb2/3)O3 ceramics

The B₂O₃ added Ba(Zn_1/3Nb_2/3)O₃ (BBZN) ceramic was sintered at 900 °C. BaB₄O₇, BaB₂O₄, and BaNb₂O₆ second phases were found in the BBZN ceramic. Since BaB₄O₇ and BaB₂O₄ second phases have an eutectic temperature around 900 °C, they might exist as the liquid phase during sintering at 900 °C and assist the densification of the BZN ceramics. Microwave dielectric properties of dielectric constant (ɛ_r) = 32, Q × f = 3500 GHz, and temperature coefficient of resonance frequency (τ_f) = 20 ppm/°C were obtained for the BZN with 5.0 mol% B₂O₃ sintered at 900 °C for 2 h. The BBZN ceramics were not sintered below 900 °C and the microwave dielectric properties of the BBZN ceramics sintered at 900 °C were very low. However, when CuO was added, BBZN ceramic was well sintered even at 875 °C. The liquid phase related to the BaCu(B₂O₅) second phase could be responsible for the decrease of sintering temperature. Good microwave dielectric properties of ɛ_r = 36, Q × f = 19,000 GHz and τ_f = 21 ppm/°C can be obtained for CuO doped BBZN ceramics sintered at 875 °C for 2 h.     

Densification behavior and electrical properties of CuO-doped Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 ternary ceramics

CuO modified Pb(In_1/2Nb_1/2)O₃–Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PIN–PMN–PT) ternary relaxor based ferroelectrics with the composition near the morphotropic phase boundary were synthesized by two-step columbite precursor method. The introduction of CuO significantly improved the sinterability of PIN–PMN–PT ceramics, resulting in the full densification of samples at lower sintering temperatures. It also profoundly modified the crystal structure and fracture mode of the ceramics. Properly increasing CuO content led to the disappearance of rhombohedral-tetragonal phase transition, remarkably improved the Curie temperature (T_c), and made the ceramics more relaxorlike. The ternary ceramics doped with 0.25 wt% CuO possessed optimum piezoelectric properties (d₃₃=584 pC/N, d₃₃^*=948 pC/N, and k_p=0.68), high ferroelectric properties (E_c=9.9 kV/cm, and P_r=33.1 μC/cm²), low dielectric loss (tan δ=0.9%), and wider temperature usage range (T_c=225 °C). The obtained properties are much higher than those of previously reported PIN–PMN–PT based ceramics, indicating that CuO doped PIN–PMN–PT is a promising candidate for electromechanical applications with high performance and wide temperature/electric field usage ranges.     

Effects of microwave sintering on the properties of 0.87(Mg0.7Zn0.3)TiO3–0.13(Ca0.61La0.26)TiO3 ceramics

0.87(Mg_0.7Zn_0.3)TiO₃–0.13(Ca_0.61La_0.26)TiO₃ (referred to as 87MZCLT) ceramics were prepared by microwave sintering and conventional sintering. The experimental results demonstrated that the sintering cycle of 87MZCLT ceramics was greatly shortened and the impurity phase (Mg_0.7Zn_0.3)Ti₂O₅ was eliminated by microwave sintering. Moreover, the 87MZCLT ceramics prepared by microwave sintering show more uniform, fine-grained microstructure as well as much less Zn evaporation. As a result, the quality factor was increased by 40% compared with conventional sintering. All samples were sintered at 1275 °C for 20 min with heating and cooling rate of 15 °C/min and gave excellent microwave dielectric properties: ?_r = 26.21, Q × f = 120,000 GHz, τ_f = ?3 ppm/°C.     

Porous acicular mullite ceramics fabricated with in situ formed soot oxidation catalyst obtained from waste MoSi2

Porous acicular mullite (3Al₂O₃·2SiO₂) ceramics containing Cu₃Mo₂O₉ as a soot oxidation catalyst was fabricated by a novel approach using commercial powders of Al₂O₃ and CuO, and powder obtained by controlled oxidation of ground waste MoSi₂. The obtained material consisted of elongated mullite grains which are known to be effective in carbon soot removal from diesel engine exhaust. The presence of in situ created Cu₃Mo₂O₉ was found to catalyze the carbon burnout which is an extremely important feature when it comes to filter regeneration, i.e., the captured soot removal. The carbon burnout temperature in the sample containing 12 wt% CuO was by 90 °C lower than that in the sample without CuO. Effect of sintering temperature as well as the effect of amount of CuO additive on mullite properties were studied. It was found that the increase in amount of CuO in samples sintered at 1300 °C decreased porosity and increased compressive strength of the porous mullite ceramics. The addition of 12 wt% CuO increased the strength of the porous mullite ceramics up to 70 MPa, whereas the porosity was reduced from 62% in the mullite without CuO to 44% in the mullite ceramics containing 12 wt% CuO. Although affected by the amount of CuO, the microstructure still consisted of elongated mullite grains.     

Microwave dielectric properties of LiNb3O8 ceramics with TiO2 additions

The microwave dielectric properties of LiNb₃O₈ ceramics were investigated as a function of the sintering temperature and the amount of TiO₂ additive. LiNb₃O₈ ceramics, which were calcined at 750 °C and sintered at 1075 °C for 2 h, showed a dielectric constant (ɛ_r) of 34, a quality factor (Q × f₀) of 58,000 GHz and a temperature coefficient of resonance frequency (τ_f) of −96 ppm/°C, respectively. The density of the samples influenced the properties of these properties. As the TiO₂ content increased in the LiNb₃O₈–TiO₂ system, ɛ_r and τ_f of the material were increased due to the mixing effect of TiO₂ phase, which has higher dielectric constant and larger positive τ_f. The 0.65LiNb₃O₈–0.35TiO₂ ceramics showed a dielectric constant ɛ_r of 46.2, a quality factor (Q × f₀) of 5800 GHz and a temperature coefficient of resonance frequency τ_f of near to 0 ppm/°C.     

Effect of Li2O–V2O5 on the low temperature sintering and microwave dielectric properties of Li1.0Nb0.6Ti0.5O3 ceramics

Li₂O–Nb₂O₅–TiO₂ based ceramic systems have been the candidate materials for LTCC application, due to their high dielectric constant and Q × f value and controllable temperature coefficient in the microwave region. However, the sintering temperature was relatively higher (above 1100 °C) for practical application. In this study, dielectric properties of Li_(1+x−y)Nb_(1−x−3y)Ti_(x+4y)O₃ solid solution were studied with different x and y contents and among them, the Li_1.0Nb_0.6Ti_0.5O₃ composition (x = 0.1, y = 0.1) was selected, due to its reasonable dielectric properties to determine the possibility of low temperature sintering. The effects of 0.17Li₂O–0.83V₂O₅, as a sintering agent, on sinterability and microwave dielectric properties of Li_1.0Nb_0.6Ti_0.5O₃ ceramics were investigated as a function of the sintering agent content and sintering temperature. With addition of 0.17Li₂O–0.83V₂O₅ above 0.5 wt%, the specimens were well densified at a relatively lower temperature of 850 °C. Only slight decrease in apparent density was observed with increasing 0.17Li₂O–0.83V₂O₅ content above 0.75 wt%. In the case of 0.5 wt% 0.17Li₂O–0.83V₂O₅ addition, the values of dielectric constant and Q × f reached maximum. Further addition caused inferior microstructure, resulting in degraded dielectric properties. For the specimens with 0.5 wt% 0.17Li₂O–0.83V₂O₅ sintered at 850 °C, dielectric constant, Q × f and TCF values were 64.7, 5933 GHz and 9.4 ppm per °C, respectively.