Preparation of yttria nanopowders for use in transparent ceramics by dry ball-milling technique

To evaluate the effectiveness of dry ball-milling, yttria powders were ball-milled, and the optimal sample was spark plasma sintered to fabricated transparent yttria ceramics. The characterization of the powders and pellets were analyzed using XRD, FESEM, UV/VIS/NIR and FTIR spectrometer throughout the whole experimental process. The results indicated that ball-milling can significantly decrease yttria particle size and enhance the specifice surface area. The best duration is 20 h ball-milling with average particle size and specifice surface area of 64 nm and 20.4 m²/g, respectively. Transparent yttria ceramic was made up of grains in the size range of approximately 0.67 μm and the relative density was 99.8%. The in-line transmittance of the SPS-sintered yttria ceramic (2.5 mm thick) reached 83% in the infrared region, which is very close to the theoretical value of yttria.     

High optical quality Y2O3 transparent ceramics with fine grain size fabricated by low temperature air pre-sintering and post-HIP treatment

High optical quality Y₂O₃ transparent ceramics with fine grain size were successfully fabricated by air pre-sintering at various temperature ranging from 1500 to 1600 °C combined with a post-hot-isostatic pressing (HIP) treatment using co-precipitated powders as the starting material. The fully dense Y₂O₃ transparent ceramic with highest transparency was obtained by pre-sintered at 1550 °C for 4 h in air and post-HIPed at 1600 °C for 3 h (the pressure of HIP 200 MPa), and it had fine microstructure and the average grain size was 0.96 μm. In addition, the in-line transmittance of the ceramic reached 81.7% at 1064 nm (1 mm thickness). By this approach, the transparent Y₂O₃ ceramics with fine grain size (<1.6 μm) were elaborated without any sintering aid.     

Transmittance improvement of Dy–α-SiAlON in infrared range by post hot-isostatic-pressing

At present stage, the transmittance improvement is still a thorny problem in SiAlON ceramics due to their complex composition and processing. In the present research, Dy–α-SiAlON ceramics were selected to be translucent in the medium infrared range. The samples had a higher densification value by using hot-pressing (HP) sintering method at 1650–1700 °C with or without LiF additive. The as-sintered specimens experienced the post-hot-isostatic-pressing (PHIP) treatment at 1650–1700 °C for 30–90 min in either N₂ or Ar environment to increase the optical transmittance. A significant optical transparency improvement has been found in Dy–α-SiAlON, with or without LiF co-doping, undergone a PHIP at 1700 °C for 30 min under an Argon gas pressure of 180 MPa. The improved transmittance attributes to a fully developed α-Sialon crystalline phase, a uniform grain size, a denser grain arrangement, and a clean grain boundary, based on the X-ray diffraction analysis, SEM and TEM microstructure observation, and optical transmittance measurement.     

Effect of sintering temperature on the microstructure and transparency of Nd,Y:CaF2 ceramics

1 at% Nd, 3 at% Y doped CaF₂ transparent ceramics were obtained by hot pressing at the sintering temperature varing from 500 to 800 °C under vacuum environment with co-precipitated CaF₂ nanopowders. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) analysis showed that the obtained nanoparticles were single fluorite phase with grain size around 26 nm. Scanning electron microscopy (SEM) observations of the Nd, Y: CaF₂ ceramics indicated that the mean grain size of the ceramic sintered at 800 °C was about 748 nm. The influence of the temperature on the grain size, microstructure and optical transmittance was investigated. For the ceramic sintered at 800 °C, the transmittance was 85.49% at the wavelength of 1200 nm. The room temperature emission spectra of Nd: CaF₂ and Nd, Y: CaF₂ ceramics were measured and discussed.     

Effects of LiF on the microstructure and optical properties of hot-pressed MgAl2O4 ceramics

Transparent magnesium aluminate spinel (MgAl₂O₄) ceramics were fabricated by hot-pressing of the MgO and α-Al₂O₃ powder mixture using LiF as a sintering aid. Effects of the LiF additive on densification, microstructure and optical properties of MgAl₂O₄ ceramics were systematically investigated. It has been found that the addition of LiF can effectively remove the porosity and increase the optical transparency of MgAl₂O₄ ceramics. For the spinel ceramics HP-ed at 1550 °C for 3 h with 1 wt% LiF addition, the average grain size is about 36 µm and the in-line transmittance exceeds 60% at the wavelength of 800 nm.     

Fabrication and properties of transparent Tb:YAG fluorescent ceramics with different doping concentrations

Terbium doped yttrium aluminum garnet (Tb:YAG) transparent ceramics with different doping concentrations were fabricated by the solid-state reaction method using commercial Y₂O₃, α-Al₂O₃ and Tb₄O₇ powders as raw materials. Samples sintered at 1750 °C for 20 h were utilized to observe the optical transmittance, microstructure and fluorescence characteristics. It is found that all the Tb: YAG ceramics with different doping concentrations exhibit homogeneous structures with grain size distributions around 22–29 µm. For the 5 at% Tb:YAG transparent ceramics, the grain boundaries are clean with no secondary phases. The photoluminescence spectra show that Tb:YAG ceramics emit predominantly at 544 nm originated from the energy levels transition of ⁵D₄→⁷F₅ of Tb³⁺ ions, and the intensity of the emission peak reaches a maximum value when the Tb³⁺ concentration is 5 at%. The in-line transmittance of the 5 at% Tb:YAG ceramics is 73.4% at the wavelength of 544 nm, which needs to be further enhanced by optimizing the fabrication process. We think that Tb:YAG transparent ceramics may have potential applications in the high-power white LEDs.     

Optical and mechanical properties of amorphous bulk and eutectic ceramics in the HfO2–Al2O3–Y2O3 system

Bulk glasses containing HfO₂ nano-crystallites of 20–50 nm were prepared by hot-pressing of HfO₂–Al₂O₃–Y₂O₃ glass microspheres at 915 °C for 10 min. By annealing at temperatures below 1200 °C, the bulk glasses were converted into transparent glass-ceramics with HfO₂ nano-crystallites of 100–200 nm, which showed the maximum transmittance of ～70% in the infrared region. An increase of annealing temperature (>1300 °C) resulted in opaque YAG/HfO₂/Al₂O₃ eutectic ceramics. The eutectic ceramics contained fine Al₂O₃ crystallites and showed a high hardness of 19.8 GPa. The fracture toughness of the eutectic ceramics increased with increasing annealing temperature, and reached the maximum of 4.0 MPa m^1/2.     

Fabrication and characterization of highly transparent Er:Y2O3 ceramics with ZrO2 and La2O3 additives

In this study, we report highly transparent Er:Y₂O₃ ceramics (0–10 at% Er) fabricated by a vacuum sintering method using compound sintering additives of ZrO₂ and La₂O₃. The transmittance, microstructure, thermal conductivity and mechanical properties of the Er:Y₂O₃ ceramics were evaluated. The in-line transmittance of all of the Er:Y₂O₃ ceramics (1.2 mm thick) exceeds 83% at 1100 nm and 81% at 600 nm. With an increase in the Er doping concentration from 0 to 10 at%, the average grain size, microhardness and fracture toughness remain nearly unchanged, while the thermal conductivity decreases slightly from 5.55 to 4.89 W/m K. A nearly homogeneous doping level of the laser activator Er up to 10 at% in macro-and nanoscale was measured along the radial direction from the center to the edge of a disk specimen, which is the prominent advantage of polycrystalline over single-crystal materials. Based on the finding of excellent optical and mechanical properties, the compound sintering additives of ZrO₂ and La₂O₃ are demonstrated to be effective for the fabrication of transparent Y₂O₃ ceramics. These results may provide a guideline for the application of transparent Er:Y₂O₃ laser ceramics.     

Microstructures and optical properties of 6Li,Ce:YAG ceramics for thermal neutron detection

The microstructures and optical properties of 5%⁶Li: Ce_3xY_3(1-x)Al₅O₁₂ (x = 0.001, 0.003, 0.05, 0.01, 0.02) transparent ceramics prepared by solid-state reaction and vacuum sintering were investigated in this paper. The results revealed that the grain size of ⁶Li,Ce:YAG ceramics at this ration conditions is 4 μm–20 μm. With the doping of Ce³⁺, the transmittance of ⁶Li,Ce:YAG ceramics decreases from 82% (x = 0.001) to 67% (x = 0.02) at 800 nm, and the intensity of transmittance peak at 340 nm and 460 nm increases. The emission peaks show red shift at around 530 nm with the increasing of Ce³⁺ concentration.     

Toward vacuum sintering of YAG transparent ceramic using divalent dopant as sintering aids: Investigation of microstructural evolution and optical property

Transparent YAG ceramics were fabricated by solid state reaction sintering using divalent dopants (CaO and MgO) as sintering additives without TEOS doping, and the effects of divalent dopants on their microstructure evolution and optical properties were investigated. It was found that CaO was more effective with respect to inhibiting grain growth than MgO, but not as effective as MgO in promoting densification. Fully dense, transparent YAG ceramics with excellent optical qualities could be achieved by optimizing the doping concentrations of CaO and MgO; the transmittance at 1064 nm was as high as 84.5% for 3 mm thick sample at the molar ratio of Ca: Mg=1:4, after sintered at 1840 °C for 8 h in vacuum.     

Sintering of Yb3+:Y2O3 transparent ceramics in hydrogen atmosphere

Highly transparent Yb³⁺:Y₂O₃ ceramics with doping concentration up to 40.0 at.% had been fabricated successfully via hydrogen atmosphere sintering, where the raw powders were synthesized by co-precipitation method. The sintering temperature is about 600 °C lower than its melting temperature. SEM investigation revealed the average grain size of Yb³⁺:Y₂O₃ ceramics sintered at 1850 °C for 9 h was about 7 μm. The highest transmittance of as-prepared 1 mm thickness samples around wavelength of 1050 nm reached 80%, which is close to the theoretical value of Y₂O₃. The optical spectroscopic properties of Yb³⁺:Y₂O₃ transparent ceramics have also been investigated, which shows that it is a very good laser material for diode laser pumping and short pulse mode-locked laser.     

Tb3+/Yb3+ co-doped Y2O3 upconversion transparent ceramics: Fabrication and characterization for IR excited green emission

Tb³⁺/Yb³⁺ co-doped Y₂O₃ transparent ceramics were fabricated by vacuum sintering of the pellets (prepared from nanopowders by uniaxial pressing) at 1750 °C for 5 h. Zr⁴⁺ and La³⁺ ions were incorporated in Tb³⁺/Yb³⁺ co-doped Y₂O₃ nanoparticle to reduce the formation of pores which limits the transparency of ceramic. An optical transmittance of ∼80% was achieved in ∼450 to 2000 nm range for 1 mm thick pellet which is very close to the theoretical value by taking account of Fresnel’s correction. High intensity luminescence peak at 543 nm (green) was observed in these transparent ceramics under 976 and 929 nm excitations due to Yb–Tb energy transfer upconversion.     

Highly transparent AlON ceramics sintered from powder synthesized by carbothermal reduction nitridation

Aluminum oxynitride (AlON) powders were synthesized by the carbothermal reduction and nitridation process using commercial γ-Al₂O₃ and carbon black powders as starting materials. And AlON transparent ceramics were fabricated by pressureless sintering under nitrogen atmosphere. The effects of ball milling time on morphology and particle size distribution of the AlON powders, as well as the microstructure and optical property of AlON transparent ceramics were investigated. It is found that single-phase AlON powder was obtained by calcining the γ-Al₂O₃/C mixture at 1550 °C for 1 h and a following heat treatment at 1750 °C for 2 h. The AlON powder ball milled for 24 h showed smaller particles and narrower particle size distribution compared with the 12 h one, which was benefit for the improvement of optical property of AlON transparent ceramics. With the sintering aids of 0.25 wt% MgO and 0.04 wt% Y₂O₃, highly transparent AlON ceramics with in-line transmittance above 80% from visible to infrared range were obtained through pressureless sintering at 1850 °C for 6 h.     

Fabrication of highly transparent AlON ceramics by hot isostatic pressing post-treatment

Highly transparent aluminum oxynitride (AlON) ceramics were fabricated by pressureless sintering with hot isostatic pressing (HIP) post-treatment. The experimental results showed that the optical transparency of AlON ceramics was improved markedly over the visible and near-infrared range by HIP at 1825 °C for 3 h in 200 MPa argon gas, which derived from the elimination of residual pores in the prepared ceramics. For AlON ceramics pre-sintered at 1800 °C, the transmittances of the sample increased from 63.6% to 84.8% at 600 nm and from 75.4% to 86.1% at 2000 nm, respectively. The average grain size of the HIPed sample was about 47.9 μm.     

Post-treatment of nanopowders-derived Nd:YAG transparent ceramics by hot isostatic pressing

Neodymium doped yttrium aluminum garnet (Nd:YAG) transparent ceramics were fabricated from Nd:YAG nanopowders synthesized via a reverse precipitation method by vacuum sintering and successive hot isostatic pressing (HIP) post-treatment. The powders obtained by calcining the precursor at 1100 °C for 4 h and then ball milling for 2 h with 0.5 wt% TEOS as sintering aid were used to fabricate Nd:YAG ceramics. The green bodies were vacuum sintered at 1500–1800 °C for 10 h, followed by the HIP at 1600 °C for 3 h in 200 MPa Ar atmosphere. Influence of the calcination temperature on the phase, morphology and particle size evolution of the nanopowders, as well as the optical transparency and microstructure of the obtained Nd:YAG ceramics before and after the HIP post-treatment was investigated in detail. It was found that for the post-treated 1800 °C-vacuum-sintered Nd:YAG ceramic sample, the in-line transmittance increased from 48.0% up to 81.2% at the lasing wavelength of 1064 nm.     

Essential Macleod Program (EMP) simulated fabrication of high quality Zn:SnO2/Ag/Zn:SnO2 multilayer transparent conducting electrode on flexible substrates

In the quest of promising Indium free amorphous transparent conducting oxide (TCO), Zn-doped SnO₂/Ag/Zn-doped SnO₂ (OMO) multilayer films were prepared on flexible polyethylene terephthalate (PET) substrates by RF sputtering at room temperature (RT). Growth parameters were optimized by varying sputtering power and working pressure, to have high electrical conductivity and optical transmittance. Optimization of the thickness of each layer was done by Essential Macleod Program (EMP) simulation to get the higher transmission through OMO multilayer. The sheet resistance and transmittance of 3 at% Zn-doped SnO₂ thin film (30 nm) were 2.23 kΩ/□, (ρ ~ 8.92×10⁻³ Ω∙cm) and 81.3% (at λ ~ 550 nm), respectively. By using optimized thicknesses of Zn-doped SnO₂ (30 nm) and Ag (12 nm) and optimized growth condition Zn-doped SnO₂/Ag/Zn-doped SnO₂ multilayer thin films were deposited. The low sheet resistance of 7.2 Ω/□ and high optical transmittance of 85.1% in the 550 nm wavelength region was achieved with 72 nm multilayer film.     

The growth of transparent amorphous carbon thin films from coal

Large-area, uniform, transparent amorphous carbon (a-C) thin films were synthesized through simple chemical vapor deposition using coal as the solid carbon source. The atomic force microscopy characterization showed that the synthesized carbon thin film has ∼5 nm thickness with ∼0.55 nm surface roughness. The optical transmittance spectrum showed that the carbon thin film has >96% optical transmittance over the spectral range from 350 nm to 900 nm. The carbon thin films can be transferred to various substrates, which show promise for applications in solar cell, optical and magnetic storage disks, light emitting diodes, photodiodes, and biomedical implants.     

Spark plasma sintering of Sm3+ doped Y2O3 transparent ceramics for visible light lasers

Transparent Sm:Y₂O₃ ceramics were fabricated by spark plasma sintering (SPS). The effects of LiF additive and sintering temperature on the microstructure and optical transmittance of the Sm:Y₂O₃ ceramics were investigated. The optimal content of LiF additive and sintering temperature was found to be 0.3 wt% and 1500 ℃. The transmittance of Sm:Y₂O₃ ceramics with a thickness of 1.7 mm reached 75.3% at 609 nm, which is about 94% of the theoretical value. The average grain size of the sample was about 50 µm.     

Influence of post-HIP temperature on microstructural and optical properties of pure MgAl2O4 spinel: From opaque to transparent ceramics

Transparent MgAl₂O₄ spinel ceramics were processed from sub-micrometric commercial powder by applying a two-step procedure: pressureless sintering under vacuum followed by hot isostatic pressing. To limit grain growth and to avoid secondary reactions or impurities, no additives or sintering aids were added to the powder. First, pressureless sintering at 1500 °C during 2 h under vacuum led to opaque samples due to a high level of porosity. To improve the optical quality of the MgAl₂O₄ ceramics and the in-line transmission in the visible range, a post-treatment by hot isostatic pressing was applied. Highly transparent ceramics were obtained after a post-treatment at 1800 °C for 10 h with an in-line transmission of 81% at 400 nm and 86% from 950 to 3000 nm for a thickness of 2 mm (98.8% of the theoretical transmission).     

Fabrication and optical characterizations of Yb,Er codoped CaF2 transparent ceramic

Nanoparticles of Yb, Er codoped calcium fluoride were obtained by a co-precipitation method. Scanning electron microscope (SEM) and X-ray powder diffraction (XRD) analysis showed that the obtained nanoparticles were single fluorite phase with grains size around 30–50 nm. Yb, Er:CaF₂ transparent ceramics were fabricated by hot pressing (HP) the nanoparticles at a temperature of 800 °C in a vacuum environment. For a 2 mm thickness ceramic sample, the transmittance at 1200 nm reached about 83%. Microstructures were characterized using SEM analysis, and the average grain size was about 700 nm. Grain boundaries of the ceramic sample were clean and no impurities were detected. The absorption, upconversion and infrared emission spectra of transparent ceramic sample under 978 nm excitation were measured and discussed.