Synthesis of TiO2(B)/SnO2 composite materials as an anode for lithium-ion batteries

A TiO₂(B) nanosheets/SnO₂ nanoparticles composite was prepared by the hydrothermal and chemical bath deposition (CBD) methods, and its electrochemical properties were investigated for use as the anode material of a lithium-ion battery. The as-prepared composites consisted of monoclinic-phase TiO₂(B) nanosheets and cassiterite structure SnO₂ nanoparticles, in which SnO₂ nanoparticles were uniformly decorated on the TiO₂(B) nanosheets. The TiO₂(B)/SnO₂ composites showed a higher reversible capacity and better durability than that of the pure TiO₂(B) for use as a battery anode. The composite electrodes exhibiting a high initial discharge capacity of 2239.1 mAh g⁻¹ and a discharge capacity of more than 868.7 mAh g⁻¹ could be maintained after 50 cycles at 0.1 C in a voltage range of 1.0–3.0 V at room temperature. The results suggest that TiO₂(B) nanosheets coated with SnO₂ could be suitable for use as a stable anode material for lithium-ion batteries. In addition, the coulombic efficiency of the nanosheets remains at an average of 93.1% for the 3rd–50th cycles.     

TiO2–SnO2 nanomaterials for gas sensing and photocatalysis

Nanopowders of TiO₂–SnO₂ over a full composition range extending from 100 mol% TiO₂ to 100 mol% SnO₂ are obtained by the sol–gel method from TTIP and SnCl₂·5H₂O precursors of Ti and Sn, respectively followed by calcination at 400 °C. The samples are characterized by means of BET, XRD and TEM. Optical properties of the prepared nanomaterials are studied as well. TEM images indicate that the nanoparticles are regular in shape. The specific surface area, SSA of TiO₂ is 95 m²/g while that of SnO₂ amounts to 129 m²/g. The highest SSA of 156 m²/g is achieved at 20 mol% of TiO₂. Occurrence of rutile, anatase and brookite polymorphic forms depends on the chemical composition of nanopowders. Formation of rutile-type solid solution of TiO₂–SnO₂ over the range of 0–80 mol% TiO₂ is confirmed by Vegard rule applied to lattice constants. Electronic band gap decreases with Ti content from 3.84 eV (100 mol% SnO₂) to 3.18 eV (100 mol% TiO₂).     

Preparation and visible light photocatalytic activity of carbon quantum dots/TiO2 nanosheet composites

Carbon quantum dots (C QDs)/TiO₂ nanosheet (TNS) composites were prepared by a simple low temperature process in which TNS were dispersed in C QDs solution, and dried at 60 °C. The C QDs/TNS composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, transmission electron microscopy (TEM) and high-resolution TEM. The results indicated that C QDs were well combined with TNS through surface carbon–oxygen groups. The photocatalytic activity was investigated by degradation of rhodamine B under visible light irradiation. The photocatalytic activity of C QDs/TNS composites was significantly enhanced compared with that of C QDs/P25 composites and pure TNS, which indicated that the unique up-converted photoluminescence behavior of C QDs and highly reactive {0 0 1} facets of TNS both played important roles in the enhancement of photocatalytic activity of C QDs/TNS composites.     

Palygorskite and SnO2–TiO2 for the photodegradation of phenol

The photocatalytic removal of phenol was studied using palygorskite-SnO₂–TiO₂ composites (abbreviated as Paly-SnO₂–TiO₂) under ultraviolet radiation. The photocatalysts were prepared by attachment of SnO₂–TiO₂ oxides onto the surface of the palygorskite by in situ sol–gel technique. The products were characterized by XRD, TEM and BET measurements. SnO₂–TiO₂ nanoparticles, with an average diameter of about 10 nm, covered the surface of the palygorskite fibers without obvious aggregation. Compared with palygorskite-titania (Paly-TiO₂), palygorskite-tin dioxide (Paly-SnO₂), and Degussa P25, Paly-SnO₂–TiO₂ and SnO₂–TiO₂ exhibited much higher photocatalytic activity. The photodecomposition of phenol was as high as 99.8% within 1.5 h. The apparent rate constants (k_app) for Paly-SnO₂–TiO_2, TiO₂, and P25 were measured. Paly-SnO₂–TiO₂ showed the highest rate constant (0.03435 min^?1). The chemical oxygen demand (COD) of the phenol solution was reduced from 220.2 mg/L to 0.21 mg/L, indicating the almost complete decomposition of phenol. Reusability of the photocatalyst was proved.     

Combustion synthesis and EIS characterization of TiO2–SnO2 system

TiO₂ is an insulator, but using specific dopants, can modify sharply its electronic structure towards semiconducting behavior. This type of response is widely applied in many electrochemical and electrocatalytical devices, namely chlorine production, hydrocarbon oxidation, CO and CO₂ hydrogenation and as electroactive substrata for biological cell growth.Combustion synthesis is a very simple, rapid and clean method for material preparation, which will be used in the preparation of the (1 − x)TiO₂–xSnO₂, x = 0.05–0.3. Tin oxalate and titanium isopropoxide are used as precursors for the synthesis. The as-prepared powders are fine and homogeneous, the average particle size is in the range of 5–10 nm, powders and ceramic compact bodies are characterized by DRX, SEM–TEM–EDX, DTA–TG and EIS. The impedance spectroscopy of the sample 10 mol% of SnO₂ indicates the presence of several phases which promote a matrix composite based in an electrical TiO₂ insulator compatible with an electronic conducting phase tin rich. This could be attributed to the spinodal decomposition effect observed in TiO₂–SnO₂ system.     

Nb2O5 nanospheres/surface-modified graphene composites as superior anode materials in lithium ion batteries

Uniform Nb₂O₅ nanospheres/surface-modified graphene (SMG) composites for anode materials in lithium ion batteries were synthesized by hydrothermal method. The microstructure and morphology of composites were investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscope techniques. The experimental results showed that Nb₂O₅ nanospheres were tightly and uniformly grown on the surface of SMG nanosheets. Nb₂O₅ nanospheres/SMG composites exhibited an impressive reversible capacity of 404.6 mA h g⁻¹ at the current density of 40 mA g⁻¹ after 100 cycles, and an excellent rate capacity of 345.5 mA h g⁻¹ at the current density of 400 mA g⁻¹.     

Synthesis of CuInS2 quantum dots on TiO2 porous films by solvothermal method for absorption layer of solar cells

Copper indium disulfide (CuInS₂) nano-particles have been synthesized by solvothermal method for absorption layer of solar cells. The CuInS₂ nano-particles can be adsorbed in pores of TiO₂ porous films. The effects of heat-treatment on crystalline structures and sizes of the CuInS₂ nano-particles were investigated. Crystalline structures and sizes were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM) investigations. Surface morphologies and optical properties were studied by field-emission scanning electron microscope (FESEM) and UV–vis spectra when CuInS₂ were absorbed on TiO₂ films.The results show that the CuInS₂ quantum dots (size is smaller than 10 nm) can be synthesized by solvothermal method at 150 °C. CuInS₂ particles sizes increase with the rise of reaction temperature and time. The CuInS₂ quantum dots can be adsorbed on TiO₂ films well and high-absorptive anodic electrode of solar cells can be prepared. Blue shift of absorption edge was observed as the sizes of CuInS₂ quantum dots decreased.     

All-solid-state quantum-dot-sensitized solar cells with compact PbS quantum-dot thin films and TiO2 nanorod arrays

To improve the electron injection efficiency from PbS quantum dots to TiO₂ nanorods and prevent the direct contact of spiro-OMeTAD and TiO₂ nanorods, a compact PbS quantum-dot thin film can be successfully obtained on TiO₂ nanorod arrays 360 nm in length by repeated spin coating of Pb(Ac)₂, Na₂S and 1,2-ethanedithiol solution in a step-by-step process. The corresponding solid-state quantum-dot-sensitized solar cells are fabricated using a novel structured FTO/compact PbS quantum-dot thin film sensitized TiO₂ nanorod array/spiro-OMeTAD/Au that achieves a photoelectric conversion efficiency of 3.57% under AM 1.5 G illumination (100 mW cm⁻²), which represents a high value among all-solid-state PbS quantum-dot-sensitized TiO₂ nanorod array solar cells.     

The size and dispersion effect of modified graphene oxide sheets on the photocatalytic H2 generation activity of TiO2 nanorods

Nano graphene oxide (NGO) was produced by further refluxing graphene oxide (GO) sheets in HNO₃, and carboxylic acid functionalized graphene oxide (GO–COOH) was obtained by a simple etherification reaction between GO and chloroacetic acid. The GO, GO–COOH and NGO sheets are combined with TiO₂ nanorods by a two-phase assembling method, and confirmed by transmission electronic microscopy. The GO–TiO₂, GO–COOH–TiO₂ and NGO–TiO₂ composites are used in a comparative study of photocatalytic H₂ generation activity under UV light irradiation. The H₂ generation rate of TiO₂ nanorods was slightly increased from 15 to 30 mL h⁻¹ g⁻¹ by replacing oleic acid ligands with hydrophilic dopamine, and significantly increased to 105 mL h⁻¹ g⁻¹ after combining with GO sheets. The further comparative study shows that GO–COOH–TiO₂ composite has higher H₂ generation rate of 180 mL h⁻¹ g⁻¹ than that of GO–TiO₂ and NGO–TiO₂ composites.     

Absorption boost of TiO2 nanotubes by doping with N and sensitization with CdS quantum dots

A process of obtaining N-doped TiO₂ nanotubes sensitized by CdS nanoparticles is presented, including detailed characterizations performed along the synthesis. Transparent TiO₂ films consisting of nanotubes, 2.5 µm long and of ~60 nm inner diameter, were obtained after anodization of a titanium film deposited onto FTO glass substrate. N-doping was achieved by annealing of TiO₂ film in ammonia. X-ray Photoelectron Spectroscopy measurements showed that nitrogen was substitutionally incorporated in the TiO₂ matrix, with the N:Ti concentration ratio of 1:100. The doping changed the optical properties of the material in such a way that the absorption edge was shifted from 380 nm to 507 nm, as observed from diffuse reflectance spectra. The influence of the microwave (MW) irradiation on the synthesized CdS quantum dots and their optical properties was investigated. It was shown that the diameter of CdS nanoparticles was increased due to releasing of S^2- ions from dimethyl sulfoxide (DMSO) as a consequence of the MW treatment. The (N)TiO₂ films were then used as substrates for matrix assisted pulsed laser deposition of the CdS quantum dots with DMSO as a matrix. The laser parameters for the deposition were optimized in order to preserve the nanotubular structure open, the latter being an important feature of this type of photoanode. The structure obtained under optimized conditions has an additional absorption edge shift, reaching 603 nm.     

Improvements in acidity for TiO2 and SnO2 via impregnation with MoO3 for the esterification of fatty acids

The impregnation of TiO₂ or SnO₂ with MoO₃ forms solid materials exhibiting high acidity (MoO₃/TiO₂ and MoO₃/SnO₂) that might be applied as catalysts for the esterification of fatty acids. TiO₂ and SnO₂ oxide matrixes were prepared using a metal-chitosan complex method, and the acidity of these materials was modified via impregnation with MoO₃. These catalytic systems were characterized by FTIR, N₂ adsorption/desorption isotherms, thermogravimetric analysis, and NH₃ temperature programmed desorption (NH₃-TPD) and tested in the esterification of fatty acids in the presence of methanol. The esterification reactions were carried out at three different temperatures (120 °C, 140 °C and 160 °C) with a 400:100 molar ratio of alcohol:fatty acid and 1% (mass) catalyst loading. Both TiO₂ and SnO₂ only exhibited catalytic activity after their acidity was improved via impregnation with MoO₃, and yields of 80% and 90%, respectively, were achieved at 6 h and 160 ºC.     

A novel TiO2 − xNx/BN composite photocatalyst: Synthesis,characterization and enhanced photocatalytic activity for Rhodamine B degradation under visible light

A novel TiO_2 − xN_x/BN composite photocatalyst was prepared via a facile method using melamine–boron acid adducts (M·2B) and tetrabutyl titanate as reactants. The morphological results confirmed that nitrogen-doped TiO₂ nanoparticles were uniformly coated on the surface of porous BN fibers. A red shift of absorption edge from 400 nm (pure TiO₂) to 520 nm (TiO_2 − xN_x/BN composites) was observed in their UV–Vis light absorption spectra. The TiO_2 − xN_x/BN photocatalysts exhibited enhanced photocatalytic activity for the degradation of Rhodamine B (RhB) and the highest photocatalytic degradation efficiency reached 97.8% under visible light irradiation for 40 min. The mechanism of enhanced photocatalytic activity was finally proposed.     

Solvothermal fabrication of three-dimensionally sphere-stacking Sb–SnO2 electrode based on TiO2 nanotube arrays

TiO₂-NTs-based Sb–SnO₂ electrode with three-dimensionally sphere-stacking structure was successfully fabricated by the solvothermal method, followed by annealing at 500 °C for 1 h. The physico-chemical properties of electrodes were characterized through scanning electron spectroscopy (SEM), X-ray diffraction (XRD) and electrochemical measurements. SEM result showed that TiO₂-NTs/Sb–SnO₂ electrode has morphology of vertically sphere-stacking coralline. Compared with Ti/Sb–SnO₂, TiO₂-NTs/Sb–SnO₂ electrode has smaller grain size and greater specific surface area which can provide with more active sites. Compared with Ti/Sb–SnO₂ electrode, TiO₂-NTs/Sb–SnO₂ has a higher oxygen evolution potential and stronger phenol oxidation peak, indicating an improved catalytic activity for phenol degradation. The kinetic analysis of electrochemical phenol degradation showed that the first-order kinetics rate constant on TiO₂-NTs/Sb–SnO₂ electrode is 1.33 times as much as that on Ti/Sb–SnO₂, confirming that the sphere-stacking Sb–SnO₂ based on TiO₂ nanotube has a good electrocatalytic activity.     

Highly sensitive acetone sensor based on Eu-doped SnO2 electrospun nanofibers

In this study, a series of undoped and Eu-doped SnO₂ nanofibers were synthesized via a simple electrospinning technique and subsequent calcination treatment. Field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were carefully used to characterize the morphologies, structures and chemical compositions of these samples. The results reveal that the as-prepared nanofibers are composed of crystallite grains with an average size of about 10 nm and Eu³⁺ ions are successfully doped into the SnO₂ lattice. Compared with pure SnO₂ nanofibers, Eu-doped SnO₂ nanofibers demonstrate significantly enhanced sensing characteristics (e.g., large response value, short response/recovery time and outstanding selectivity) toward acetone vapor, especially, the optimal sensor based on 2 mol% Eu-doped SnO₂ nanofibers shows the highest response (32.2 for 100 ppm), which is two times higher than that of the pure SnO₂ sensor at an operating temperature of 280 °C. In addition, the sensor exhibits a good sensitivity to acetone in sub-ppm concentrations and the detection limit could extend down to 0.3 ppm, making it a potential candidate for the breath diagnosis of diabetes.     

The photo-catalytic activities of neodymium and fluorine doped TiO2 nanoparticles

A series of photo-catalysts were synthesized by neodymium and fluorine doped TiO₂, and their characteristics evaluated by X-ray diffraction (XRD), UV–vis diffuse reflectance spectra (UV–vis), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). Neodymium and fluorine doped TiO₂ has obvious absorption in the visible light and the absorption edge shifts toward red wavelength. In addition, compared with pure TiO₂, the doped catalyst has intense absorption at 528, 587, 750, 808, and 881 nm. The catalytic efficiency was tested by monitoring the photo-catalytic degradation of methylene blue (MB) in visible light and ultraviolet light. The results showed that the optimum doping content was Nd:F:TiO₂ = 0.5:5:100 (molar ratio) heat treated at 500 °C, and the reaction rates of MB degradation were estimated to be about 1.76 times and 1.45 times higher than undoped TiO₂ in ultraviolet light and visible light.     

Preparation and electrochemical performance of SnO2@carbon nanotube core–shell structure composites as anode material for lithium-ion batteries

Carbon nanotube-encapsulated SnO₂ (SnO₂@CNT) core–shell composite anode materials are prepared by chemical activation of carbon nanotubes (CNTs) and wet chemical filling. The results of X-ray diffraction and transmission electron microscopy measurements indicate that SnO₂ is filled into the interior hollow core of CNTs and exists as small nanoparticles with diameter of about 6 nm. The SnO₂@CNT composites exhibit enhanced electrochemical performance at various current densities when used as the anode material for lithium-ion batteries. At 0.2 mA cm^?2 (0.1C), the sample containing wt. 65% of SnO₂ displays a reversible specific capacity of 829.5 mAh g^?1 and maintains 627.8 mAh g^?1 after 50 cycles. When the current density is 1.0, 2.0, and 4.0 mA cm^?2 (about 0.5, 1.0, and 2.0C), the composite electrode still exhibits capacity retention of 563, 507 and 380 mAh g^?1, respectively. The capacity retention of our SnO₂@CNT composites is much higher than previously reported values for a SnO₂/CNT composite with the same filling yield. The excellent lithium storage and rate capacity performance of SnO₂@CNT core–shell composites make it a promising anode material for lithium-ion batteries.     

TiO2 nanofibers doped with rare earth elements and their photocatalytic activity

In the present study rare earth doped (Ln³⁺–TiO₂, Ln = La, Ce and Nd) TiO₂ nanofibers were prepared by the sol–gel electrospinning method and characterized by XRD, SEM, EDX, TEM, and UV-DRS. The photocatalytic activity of the samples was evaluated by Rhodamine 6G (R6G) dye degradation under UV light irradiation. XRD analysis showed that all the synthesized pure and doped titania nanofibers contain pure anatase phase at 500 °C but at 700 °C it shows both anatase and rutile phase. XRD result also shows that Ln³⁺-doped titania probably inhibits the phase transformation. The diameter of nanofibers for all samples ranges from 200 to 700 nm. It was also observed that the presence of rare-earth oxides in the host TiO₂ could decrease the band gap and accelerate the separation of photogenerated electron–hole pairs, which eventually led to higher photocatalytic activity. To sum up, our study demonstrates that Ln³⁺-doped TiO₂ samples exhibit higher photocatalytic activity than pure TiO₂ whereas Nd³⁺-doped TiO₂ catalyst showed the highest photocatalytic activity among the rare earth doped samples.     

Tuning the microwave dielectric properties of Zn2SnO4 ceramics by adding Ca0.8Sr0.2TiO3

The influence of sintering temperature on the microwave dielectric properties and microstructure of the (1−y)Zn₂SnO₄–yCa_0.8Sr_0.2TiO₃ ceramic system were investigated with a view to their application in microwave devices. A (1−y)Zn₂SnO₄–yCa_0.8Sr_0.2TiO₃ ceramic system was prepared by the conventional solid-state method. The X-ray diffraction patterns of the 0.85Zn₂SnO₄–0.15Ca_0.8Sr_0.2TiO₃ ceramic system did not significantly vary with sintering temperature. A dielectric constant of 9.6, a quality factor (Q×f) of 15,900 GHz, and a temperature coefficient of resonant frequency of −4 ppm/°C were obtained when the 0.85Zn₂SnO₄–0.15Ca_0.8Sr_0.2TiO₃ ceramic system was sintered at 1175 °C for 4 h.     

Enhanced optical,visible light catalytic and electrochemical properties of Au@TiO2 nanocomposites

Au@TiO₂ nanocomposites and pure TiO₂ were successfully used to know the effect of Au on TiO₂ and their comparative optical, visible light catalytic and electrochemical activities were investigated. Optical parameters such as band gap energy (E_g = 2.4 eV), absorption coefficient (α), refractive index (n) and dielectric constants (σ) have been determined using different methods. Visible light (λ = ～590 nm) catalytic activity of Au@TiO₂ nanocomposites was performed for reducing methyl orange (MO) under visible light irradiation. CV, EIS and DPV studies demonstrate that Au@TiO₂ nanocomposites exhibit redox behavior, charged its surface by accumulating electrons, store and release the electrons.     

Iron-doped TiO2 nanotubes with high photocatalytic activity under visible light synthesized by an ultrasonic-assisted sol-hydrothermal method

A series of iron-doped anatase TiO₂ nanotubes (Fe/TiO₂ NTs) catalysts with iron concentrations ranging from 0.88 to 7.00 wt% were prepared by an ultrasonic-assisted sol-hydrothermal process. The structures and the properties of the fabricated Fe/TiO₂ NTs were characterized in detail and photocatalytic activity was examined using a reactive brilliant red X-3B aqueous solution as pollutant under visible light. The lengths of the NTs were determined to range from 20 nm to 100 nm. The incorporation of the iron ions (Fe³⁺) into the TiO₂ nanotubes shifted the photon absorbing zone from the ultraviolet (UV) to the visible wavelengths, reducing the band gap energy from 3.2 to 2.75 eV. The photocatalytic activity of the Fe/TiO₂ NTs was 2–4 times higher than the values measured for the pure TiO₂ nanotubes.