Characterization and X-ray peak broadening analysis in PZT nanoparticles prepared by modified sol–gel method

Lead zirconate titanate nanoparticles (PZT-NPs) were synthesized by a modified sol–gel method and were calcinated at temperatures of 600, 650 and 700 °C. Fourier transform infrared (FTIR), powder X-ray diffraction (XRD) and thermal analysis (TGA/DTA), indicate that single-phase perovskite PZT-NPs are obtained after heat treatment at a temperature of 650 °C. The TEM results obtained from the PZT-NPs confirm that the morphology of the PZT nanoparticles is spherical, with an average diameter size of 17 nm. We also investigated the crystallite development in the nanostructured PZT by X-ray peak broadening analysis. The individual contribution of many small crystallite sizes and lattice strains to the peak broadening in the PZT nanoparticles prepared at different temperatures were studied using Williamson–Hall (W–H) analysis in the range of 2θ = 15–80°.     

Optical properties of Nb-doped TiO2 thin films prepared by sol–gel method

In this work, we studied optical properties of pure and Nb-doped TiO₂ synthesized using a sol–gel method and deposited as thin films by spin-coating followed by annealing in air at 500 °C for 1 h. The surface elemental composition was derived from X-ray photoelectron spectra, while structure and surface morphology were investigated using X-ray diffraction and atomic force/scanning electron microscopy. Finally, the optical properties were investigated by means of UV–vis spectrophotometry and spectroscopic ellipsometry.The Nb content was determined from XPS measurements to vary between 1.8 and 4.3 at%. The XRD patterns of the deposited thin films, with a maximum thickness of about 56 nm, showed no diffraction peaks. As proven both by microscopy and spectroscopic ellipsometry studies doping TiO₂ with Nb modified the surface morphology of the samples; the grain size is increasing while the surface roughness decreases with the increase in Nb content. This is accompanied by a decrease in the refractive index and an increase of the extinction coefficient.     

Effect of carbon nanotubes on sintering behavior of alumina prepared by sol–gel method

Alumina (Al2O3)/carbon nanotube (CNT) (99/1 by weight) composite was prepared by mixing CNT dispersion with AlCl₃-based gel, followed by high temperature sintering at a temperature up to 1150 °C in argon. Composite alumina precursor showed phase transition order from amorphous to γ-Al₂O₃ after sintered at 900 °C for 2 h, partially to θ-Al₂O₃ after sintered at 1000 °C for 2 h, and then partially to α-Al₂O₃ after sintered at 1150 °C for 2 h. By comparison, control alumina precursor directly transformed from amorphous to α-Al₂O₃ after sintered at a relatively low temperature of 600 °C for 2 h. Composite alumina showed porous structure with pore diameter ranging from 100 nm to 2 µm, whereas control alumina was relatively pore-free. The elevated alumina-crystal phase transition temperatures and the formation of porous structure were ascribed to the presence of CNTs in alumina precursor. The composite alumina sintered at 900 °C for 2 h containing only γ-Al₂O₃ had a BET surface area of 138 m²/g, which was significantly higher than that of control alumina sintered at 1150 °C for 2 h containing only α-Al₂O₃, ~15 m²/g.     

Formation and characterization of p-type semiconductor CuCrO2 thin films prepared by a sol–gel method

This study adopted the sol–gel method to synthesize p-type semiconductor CuCrO₂ films and analyzed the effects of an annealing treatment, under a controlled argon atmosphere by changing the temperature and time, on the phase transformation, micro- and nano-structure, composition, and semiconductor properties of thin films. In the Cu–Cr–O phase transformation system, CuO, Cr₂O₃, and CuCr₂O₄ were the intermediate phases of the reaction for forming CuCrO₂: in the metastable state reaction process, the composite phases changed into a single phase, CuCrO₂; in the stable-state reaction process of CuCrO₂, carbon elements of precursors were released and eliminated; and finally the optoelectronic properties of the CuCrO₂ thin film were adjusted and changed. The CuCrO₂ thin film possessed cell- and polygon-like shaped microstructures. The carbon content in the CuCrO₂ film decreased, so the copper, chromium, and oxygen contents increased accordingly. The optical band gap of CuCrO₂ thin film increased from 2.81 eV to 3.05 eV, while the resistivity decreased. The nanoscale crystal was identified which also of the delafossite CuCrO₂ structure. Using the sol–gel method to prepare the CuCrO₂ thin films, an appropriate annealing temperature and time were helpful in forming the single-phase CuCrO₂; the decrease of precursor elements in the thin film could enhance the band gap and the conductivity of the material.     

One-pot synthesis of α-Fe2O3 nanospheres by solvothermal method

We have successfully prepared α-Fe₂O₃ nanospheres by solvothermal method using 2-butanone and water mixture solvent for the first time, which were about 100 nm in diameter and composed of very small nanoparticles. The as-prepared samples were characterized using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The results showed that the product was α-Fe₂O₃ nanosphere, and the temperature was an important factor on the formation of α-Fe₂O₃ nanospheres.     

Multilayer zirconium titanate thin films prepared by a sol–gel deposition method

Zirconium titanate multilayer thin films were prepared by an aqueous particulate sol–gel process followed by spin coating. The obtained structures were studied by transmission electron microscope, scanning electron microscope, atomic force microscope, and spectroscopic reflection analyses. According to the results, sound thin films up to three layers were developed, accompanied by an increase in thickness and roughness by increasing the number of the layers. It was also found that the coatings consist of globular nanoparticles with an average diameter of 50 nm. Considering the contribution of roughness to biological responses, the optimization of the surface characteristics to meet an optimal performance seems to be a challenging issue, which demands future studies.     

Highly selective removal of 2,4-dinitrophenol by a surface imprinted sol–gel polymer

In this work, 2,4-dinitrophenol (2,4-DNP), a new molecularly imprinted polymer (MIP) with excellent performance was synthesized in ethanol by the sol–gel method using 3-aminopropyltriethoxysilane as functional monomer on the surface of silica particles. The structure and morphology of MIP were characterized via scanning electron microscopy, nitrogen adsorption–desorption analysis, infrared spectra, and thermogravimetry analysis. Results demonstrated that MIP had excellent selectivity toward the template molecule (2,4-DNP) with an imprinting factor of 9.55 and a maximum static adsorption capacity of 114.7 mg g⁻¹. Data obtained from the adsorption isotherm of 2,4-DNP were fitted well with the Freundlich isotherm model, and the adsorption process can be described by the pseudo-second-order model. The investigation of adsorption mechanism revealed that the specific recognition process of MIP toward 2,4-DNP was dominated by the hydrogen bond and molecular structure. By employing as a sorbent, the as-prepared MIP was applied to recognize and remove 2,4-DNP in poster paper, nonwoven fabric and brown curtain with recoveries in the range from 85.74 to 100.00%. However, the MIP can effectively remove 2,4-DNP after five cycles.     

Structural properties and hyperfine interactions in Co–Zn Y-type hexaferrites prepared by sol–gel method

Y-type barium hexaferrites Ba₂Co_2−xZn_xFe₁₂O₂₂ (0.0≤x≤2.0) were prepared using sol–gel method and then sintering at temperatures between 900 and 1100 °C. The properties of the prepared samples were investigated using X-ray diffraction, scanning electron microscopy, and Mössbauer spectroscopy. XRD patterns revealed the presence of a single Y-type hexaferrite phase in the samples sintered at temperatures above 1000 °C. Mössbauer data indicated that Co²⁺ ions occupied octahedral sites in the T blocks, while Zn²⁺ ions were distributed between the two tetrahedral sites. This trend for cationic distribution resulted in weakening the superexchange interactions between spin-up and spin-down sublattices with increasing Zn content, and a consequent reduction in the hyperfine fields in Zn rich compounds.     

Synthesis of silica nanoparticles from Vietnamese rice husk by sol–gel method

Silica powder at nanoscale was obtained by heat treatment of Vietnamese rice husk following the sol–gel method. The rice husk ash (RHA) is synthesized using rice husk which was thermally treated at optimal condition at 600°C for 4 h. The silica from RHA was extracted using sodium hydroxide solution to produce a sodium silicate solution and then precipitated by adding H₂SO₄ at pH = 4 in the mixture of water/butanol with cationic presence. In order to identify the optimal condition for producing the homogenous silica nanoparticles, the effects of surfactant surface coverage, aging temperature, and aging time were investigated. By analysis of X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, the silica product obtained was amorphous and the uniformity of the nanosized sample was observed at an average size of 3 nm, and the BET result showed that the highest specific surface of the sample was about 340 m²/g. The results obtained in the mentioned method prove that the rice husk from agricultural wastes can be used for the production of silica nanoparticles.     

Single-phase γ-Fe2O3 nanoparticles synthesized by green ionothermal method and their magnetic characterization

The γ-Fe₂O₃ nanoparticles were prepared by ionothermal method in ionic liquids. A wide range of maghemite particle sizes within the nanometer scale are obtained by this method. The structural and magnetic properties of these γ-Fe₂O₃ particles were studied by using XRD, SEM and IR. Magnetic properties of the prepared nanoparticles were evaluated on a vibrating sample magnometer (VSM). By changing the ionic liquids, particles with an average diameter from 5 to 10 nm were prepared. The size of the final particle decreases with the longer alkyl chain of ionic liquid in this method while the template is bounded to the particle surface. Also magnetic properties of the products change with different ionic liquids. A longer alkyl chain in ionic liquid causes an increase in the magnetic properties in this method.     

Characterization of wollastonite coatings prepared by sol–gel on Ti substrate

Wollastonite coatings were prepared by sol–gel on Ti substrate and their microstructures have been studied. The phase compositions and the surface morphologies of these coatings were examined by X-ray diffraction and scanning electron microscopy. Thermal behavior of dried gel was examined by differential scanning calorimetry (DSC) and thermogravimetry (TG). There are many cracks among coatings and particles with size about 200–300 nm distributing inside cracks. DSC and TG results show that the glass transformation temperature of dried gel is about 850°C. After calcined at temperature 900°C, the phase of coatings consists of wollastonite, SiO₂, and CaSi₂O₅.     

Preparation of high pure α-Al2O3 nanoparticles at low temperatures using Pechini method

A Pechini process was successfully used to synthesize alpha-alumina (98.95% mass fraction) at relatively low calcination temperature (925 °C). The synthesis of these nanoparticles was carried out using a polymer prepared from citric acid and ethylene glycol by the melt blending method. This polymer worked as a chelating agent for aluminum cations. The final products were produced after a dual-stages thermal treatment. The resulting α-alumina consisted of nanoparticles of 8–16 nm in diameters with a surface area (～8 m² g^?1). The mass fraction of α-alumina was dependent on the concentration of aluminum salt and polymer precursor's solutions, while the surface area of the final product was dependent on the mass fraction of θ-alumina.     

Using modified Pechini method to synthesize α-Al2O3 nanoparticles of high surface area

A modified Pechini method for the preparation of a high surface area α-alumina is proposed. The synthesis of these nanoparticles was carried out using a polymer as a chelating agent. The polymer was prepared from citric acid and acrylic acid by the melt blending method. The resulting α-alumina (98.16%) after calcination at 900 °C consisted of cylindrical nanoparticles of 100–200 nm in length and <25 nm in diameter with a relatively high surface area (18 m² g^?1).     

Synthesis and optical characterization of Er-doped bismuth titanate nanoparticles grown by sol–gel hydrothermal method

The Er³⁺-doped bismuth titanate (Bi₄Ti₃O₁₂, BIT) nanoparticles were synthesized by a combined sol–gel and hydrothermal method under a partial oxygen pressure of 30 bar. The composition and morphology were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman scattering. They showed pure and homogeneous spherical BIT nanoparticles with a size below the 30 nm. The incorporation of Er ions showed a strong decrease in the lattice parameters, as well as averaged particle size. The photoluminescence up-conversion (excitation wavelength =1480 nm) showed an enhancement of the infrared emission (980 nm) as Er concentration increased, achieving a maximum for 6% mol, while photoluminescence spectra (excitation wavelength =473 nm) showed a strong green emission (529 and 553 nm) with a maximum at 4% mol.     

Infrared luminescence in Er3+:Yb3Al5O12 bulk ceramics prepared by sol–gel method

Erbium doped and pure ytterbium aluminium garnet (YbAG, Yb₃Al₅O₁₂) bulk ceramics were successfully prepared by a chelating sol–gel route based on the polyesterification of ethylenediaminetetraacetic acid (EDTA) with triethanolamine (TEA). The gel decomposition and phase formation in precursor powders were studied using XRD and TG/DTA. Amorphous precursor was directly converted to YbAG phase after calcinations at 800 °C. The influence of intermediate grinding on microstructure and luminescent properties was investigated. The discrete luminescence bands of the ⁴I_13/2 → ⁴I_15/2 transition were observed in the infrared emission spectra of erbium doped samples. The lifetime of luminescence at 1530 nm was 2.82 ms and 1.82 ms for the doped samples. This may be attributed to the different efficiency of surface recombination channel, caused by different grain size distribution. Prepared samples are suitable as a standard for photoluminescence measuring of Er-doped YbAG thin films.     

Structure and optical properties of transparent Er3+-doped CaF2–silica glass ceramic prepared by controllable sol–gel method

Transparent Er³⁺-doped CaF₂–silica glass ceramics were prepared by the direct physical introduction of Er³⁺ doped CaF₂ nanocrystals into acid-catalyzed sol–gel silica glass. The physical methods of ball milling, ultrasonic baths, and stirring were investigated to disperse Er³⁺ doped CaF₂ nanocrystals in the silica sols. The CaF₂–silica sol mixture went through gelation and heat-treatment to form Er³⁺-doped CaF₂–silica glass ceramics. The morphology of Er³⁺ doped CaF₂ in silica glass did not change after heat-treatment at 600 °C for 10 h. The experimental results showed that Er³⁺ doped CaF₂ in the glass ceramic prepared with the assistance of ball milling possesses the best dispersity and homogeneity. The highest in-line transmittance of the glass ceramic reached up to 85% in visible region. Glass ceramic exhibits efficient up-conversion emissions corresponding to the Er³⁺:⁴F_9/2→⁴I_15/2 transition and long lifetime of ⁴F_9/2 level (1.73 ms) under 980 nm excitation.     

Antireflective coatings prepared by sol–gel processing: Principles and applications

Sol–gel processing is a powerful tool to prepare antireflective (AR) coatings on optical surfaces. In this paper the different strategies to obtain antireflective properties are reviewed: porous λ/4 layers, multilayer interference-type films and index-gradient materials such as “moth eye” structures. The processing of the respective films is described and evaluated; references to respective commercial products on glass substrates are given.AR coatings may have a particularly high importance for transparent ceramics as their index of refraction is significantly higher than that of common glass types. Reflective losses therefore are higher which is especially unpleasant for materials with a yet improvable intrinsic transparency.Recent studies indicate that specific porous λ/4 layers may exhibit pronounced anti-soiling features. Laboratory experiments as well as outdoor exposure tests were used to demonstrate the dust-repellant properties.     

Porous water repellent silica coatings on glass by sol–gel method

Development of the solid surfaces with water-repellent and self-cleaning ability has attracted much research interest in recent years. In the present research work, we have prepared water repellent silica coatings on glass at room temperature (~27 °C) by sol gel process and surface silylation technique. Coating sol was prepared by keeping the molar ratio of tetramethoxysilane (TMOS), methanol (MeOH) and water (H₂O) constant at 1:12.36:4.25, respectively, with 0.01 M NH₄F. The dip coated silica films were surface silylated using two different silylating agents namely hexamethyldisiloxane (HMDSO) and hexamethyldisilazane (HMDZ). The HMDSO and HMDZ in hexane solvent were varied from 0 to 1 vol.% and silylation period was varied from 1 to 3 h. The HMDSO and HMDZ modified films showed dense and porous surface morphology, respectively. The HMDSO modified silica films showed static water contact angle of 122° whereas HMDZ modified films showed 165°. The HMDZ modified films displayed the extreme water repellency comparing with that of lotus leaves. The silica films were characterized by surface profilometer, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared microscopy, thermal and chemical aging tests, optical transmission and static water contact angle measurements.     

Preparation of nanocrystalline SrTiO3 powder by sol–gel combustion method

In this research a sol–gel combustion route has been presented to synthesize strontium titanate (SrTiO₃:ST) nanocrystalline, using citric acid as fuel. The synthesis procedure was optimized by systematically varying the molar ratios of total metal nitrate to citric acid (MN:CA) from 1:1 to 1:3. The effect was investigated through XRD, SEM and TEM analysis. Analysis of XRD spectrum shows the complete of SrTiO₃ nanocrystalline, however, a minor phase of SrCO₃ impurity was found. Hence, an acid treatment process, with 1 mol/l HNO₃ solution and deionized water, was applied to remove the impurity. The results show that the appropriate condition to prepare the single phase nanocrystalline SrTiO₃ powders is MN:CA molar ratio of 1:3, coupled with an acid treatment process and at the lower calcination temperature of 500 °C. The particle size of powders was in nanometer ranges. The average crystallite size calculated from FWHM was about 23 nm. Morphology of powders was identified by SEM analysis. However, TEM estimated the average particle size about 7.5 nm after applying an acid treatment technique at 600 °C.