Rapid and uniform in-situ solidification of alumina suspension via a non-contamination DCC-HVCI method using MgO sintering additive as coagulating agent

A novel rapid, uniform and non-contamination in-situ solidification method for alumina suspension by DCC-HVCI method using MgO sintering additive as coagulating agent was reported. MgO was used to release Mg²⁺ in suspensions via reaction with acetic acid generated from glycerol diacetate (GDA) at elevated temperature as well as to improve density and suppress grain growth of alumina ceramics during sintering. Influence of adding 0.7 wt% MgO with 2.0 vol% GDA in alumina suspension on coagulation process and properties of green bodies and sintered samples were investigated. It was indicated that the controlled coagulation of the suspension could be achieved after treating at 70 °C for 10 min. Homogeneous composition distribution of Mg element in EDS result indicated the uniform solidification of suspensions. Compressive strength of wet-coagulated bodies is 2.09±0.25 MPa. Dense alumina ceramics with relative density of 99.2% and flexural strength of 354±16 MPa sintered at 1650 °C for 4 h present homogeneous microstructure. The result indicated that the novel DCC-HVCI method via a sintering additive reaction with no contamination, short coagulation time and uniform in-situ solidification is a promising colloidal forming method for preparing high-performance ceramic components with complex shape.     

Direct coagulation casting of yttria-stabilized zirconia using magnesium citrate and glycerol diacetate

Direct coagulation casting via controlled release of high valance counter ions (DCC-HVCI) has been reported in recent years. In this paper, concentrated yttria-stabilized zirconia (YSZ) suspensions were coagulated using DCC-HVCI method with magnesium citrate as coagulating agent assisted by pH shift in the presence of glycerol diacetate. The effect of ammonium polyacrylate (PAA-NH₄) on the dispersibility of YSZ powder was investigated. The influence of concentrations of glycerol diacetate and magnesium citrate on pH and viscosities of YSZ suspensions was studied. The results indicate that concentrated YSZ suspensions can be coagulated by adding 2 vol% glycerol diacetate and magnesium citrate above 0.5 wt% at room temperature for 2–5 h. The compressive strength of coagulated wet samples is above 2.0 MPa. YSZ ceramics sintered at 1450 °C show homogeneous microstructures with relative densities of 98.9–99.2%. Flexural strength of YSZ ceramics is 869±84 MPa.     

Rapid in-situ solidification of SiO2 suspension by direct coagulation casting via controlled release of high valence counter ions from calcium iodate and pH shift

Rapid in-situ solidification of SiO₂ suspension under the joint action of releasing calcium ions and shifting pH has been proposed. When the suspension was heated up to 60 ℃, decomposition of calcium iodate which released calcium ions, as well as hydrolysis of diacetate (GDA) which shifted the pH toward the isoelectric point, both contributed to the solidification of suspension. The controlled coagulation of SiO₂ suspension could be realized via controlled release of high valence counter ions and pH shift at 60 ℃ within 30 min, which could considerably shorten the coagulation time compared with present reported results (1–3 h). Green body prepared by heating the SiO₂ suspension with 6.5 g L⁻¹ calcium iodate and 2.0 vol% GDA at 60 ℃ for 30 min shows uniform microstructure with compressive strength of close to 0.3 MPa. SiO₂ ceramics sintered at 1275 ℃ for 3 h possess homogeneous microstructure with bulk density of 2.06 g cm⁻³ and flexural strength of 40.3 MPa.     

Properties and microstructure evolution of Cf/SiC composites fabricated by polymer impregnation and pyrolysis (PIP) with liquid polycarbosilane

In the present study, a novel liquid polycarbosilane (LPCS) with a ceramic yield as high as 83% was applied to develop 3D needle-punched C_f/SiC composites via polymer impregnation and pyrolysis process (PIP). The cross-link and ceramization processes of LPCS were studied in detail by FT-IR and TG-DSC; a compact ceramic was obtained when LPCS was firstly cured at 120 °C before pyrolysis. It was found that the LPCS-C_f/SiC composites possessed a higher density (2.13 g/cm³) than that of the PCS-C_f/SiC composites even though the PIP cycle for densification was obviously reduced, which means a higher densification efficiency. Logically, the LPCS-C_f/SiC composites exhibited superior mechanical properties. The shorter length and rougher surfaces of pulled-out fibers indicated the LPCS-C_f/SiC composites to possess a stronger bonding between matrix and PyC interphase compared with the PCS-C_f/SiC composites.     

Effect of short fibers on residual permeability and mechanical properties of hybrid fibre reinforced high strength concrete after heat exposition

Mechanical and permeability performance of fibre reinforced high strength concrete after heat exposition were evaluated in the experimental study. Cylindrical concrete specimens were exposed to heat with the rate of 10 °C/min of up to 400 °C. In order to study the effect of short fibres on residual performance of heated high strength concrete, polypropylene and steel fibres had been added into the concrete mix. The melting and vaporization of its fibre constituents were found to be responsible for the significant reduction in residual properties of polypropylene fibre reinforced high strength concrete. In terms of non-destructive measurement, UPV test was proposed as a promising initial inspection method for fire damaged concrete structure. Furthermore, the effect of hybrid fibre on the residual properties of heated fibre reinforced high strength concrete was also presented.     

Waste recycling of coal fly ash: A novel approach to prepare hierarchically porous coal fly ash/Al2O3 ceramic composite with high porosity and high strength templated by emulsion-assisted self-assembly

The coal fly ash (CFA) produced from coal-fired power generation is classified as a common solid waste; thus, improving the recovery and utilization rate of CFA is highly desirable. In this study, a novel strategy using CFA and Al₂O₃ as raw materials, to prepare hierarchically porous ceramic composites that serve as potential candidates for future building materials is developed. In this process, the well-developed self-assembly method in which an anionic modifier is used to prepare hydrophobic powders that form an attractive oil/water network via electrostatic interactions, thereby yielding honeycomb-like structures. In order to explore the mechanism of preparation, five samples with different mixture ratios of alumina and CFA were prepared according to 1: 0, 2: 1, 1: 1, 1: 2, and 0: 1 (Alumina: CFA). Compared with the sample prepared with pure CFA, the as-prepared CFA/Al₂O₃ composite exhibited both superior porosity and high mechanical property. When the porosity is as high as 73 ± 0.17%, the compressive strength is as high as 80.9 ± 3.4mpa (alumina: CFA = 1:1). As the porosity decreases to 49.3 ± 0.7%, the compressive strength reaches 159.33 ± 36.89mpa (alumina: CFA = 1:2). Moreover, this work obtains the highest compressive strength-porosity related B-value in comparison to previously reported CFA-based composites and provides a new insight into the effective recycling of CFA and offers a novel approach to prepare CFA/Al₂O₃ composite with excellent overall mechanical properties.     

Nanoindentation study of nickel manganite ceramics obtained by a complex polymerization method

The chemical synthesis of nickel manganite powder was performed by a complex polymerization method (CPM). The obtained fine nanoscaled powders were uniaxially pressed and sintered at different temperatures: 1000–1200 °C for 2 h, and different atmospheres: air and oxygen. The highest density was obtained for the sample sintered at 1200 °C in oxygen atmosphere. The energy for direct band gap transition (Eg) calculated from the Tauc plot decreases from 1.51 to 1.40 eV with the increase of the sintering temperature. Indentation experiments were carried out using a three-sided pyramidal (Berkovich) diamond tip, and Young's modulus of elasticity and hardness of NTC (negative temperature coefficient) ceramics at various indentation depths were calculated. The highest hardness (0.754 GPa) and elastic modulus (16.888 GPa) are exhibited by the ceramics sintered at highest temperature in oxygen atmosphere.     

Fabrication of toughened B4C composites with high electrical conductivity using MAX phase as a novel sintering aid

MAX phase Ti₃AlC₂ was chosen as a novel sintering aid to prepare electrically conductive B₄C composites with high strength and toughness. Dense B₄C composites can be obtained at a hot-pressing temperature as low as 1850 °C with 15 vol% Ti₃AlC₂. The enhanced sinterability was mainly ascribed to the in situ reactions between B₄C and Ti₃AlC₂ as well as the liquid phase decomposed from Ti₃AlC₂. Both the Vickers hardness and fracture toughness increase with increasing Ti₃AlC₂ amount, and high hardness and toughness values of 28.5 GPa and 7.02 MPa m^−1/2 respectively were achieved for B₄C composites sintered with 20 vol% Ti₃AlC₂ at 1900 °C. Crack deflection by homogenously distributed TiB₂ particles was identified as the main toughening mechanism. Besides, B₄C composites sintered with Ti₃AlC₂ show significantly improved electrical conductivity due to the percolation of highly conductive TiB₂ phase, which could enhance the machinability of B₄C composites largely by allowing electrical discharge machining.     

Fabrication of short carbon fibre reinforced SiC multilayer composites by tape casting

Silicon carbide multilayer composites containing short carbon fibres (C_sf/SiC) were prepared by tape casting and pressureless sintering. C fibres were dispersed in solvents and then mixed with SiC slurry to make green C_sf/SiC tape. Triton X-100 was found to be the best one for Toho Tenax HTC124 fibres (with water soluble coating) among BYK-163, BYK-410, BYK-2150, BYK-9076, BYK-9077 and Triton X-100 dispersants. C_sf/SiC multilayer composites containing 5 vol.% fibre (mean fibre length of 3, 4.5, and 6 mm) were obtained. Addition of short C fibres seems to worsen the densification process in the C_sf/SiC multilayer composites, whereas anisotropy shrinkage in C_sf/SiC was also observed. Open pores size was increased slightly after the addition of C fibre but it decreased with the mean fibre length. Mechanical properties were affected by high residual porosity. The addition of short C fibre has not changed the crack deflection at weak interfaces. C_sf/SiC multilayer composites containing longer fibres (4.5 and 6 mm) presented higher elastic modulus, bending strength and Vickers hardness as compared to shorter fibres (3 mm). Improved sintering performance and fibre content are necessary to improve mechanical properties.     

Microstructure and mechanical properties of dental 3Y-TZP ceramics by using CaO-P2O5 glass as additive

This study investigated the effects of glass frits on the sintering and mechanical properties of dental 3Y-TZP ceramics. The glass frits, which consisted of MgO, CaO, Al₂O₃, SiO₂, and P₂O₅, were selected to lower the sintering temperature of zirconia via liquid phase sintering.The results of the experiment showed that these glass frit additives neither destroy the stability of the high temperature t-phase nor induce grain growth. All the mechanical properties and the relative densities were strongly correlated with the addition of glass frits. At lower sintering temperatures, the presence of glass additives resulted in an increase in mechanical properties. At higher sintering temperatures, the presence of glass additives decreased the mechanical properties.