Preparation and characterization of porous mullite ceramics via foam-gelcasting

Porous mullite ceramics were prepared via foam-gelcasting using industrial grade mullite powder as the main raw materials, Isobam-104 as the dispersing and gelling agent, sodium carboxymethyl cellulose as the foam stabilizing agent, and triethanolamine lauryl sulfate as the foaming agent. The effects of processing parameters such as type and amount of additive, solid loading level and gelling temperature on rheological properties and gelling behaviors of the slurries were investigated. The green samples after drying at 100 °C for 24 h were fired at 1600 °C for 2 h, and the microstructures and properties of the resultant porous ceramic samples were characterized. Based on the results, the effects of foaming agent on the porosity level, pore structure and size and mechanical properties of the as-prepared porous mullite ceramics were examined. Porosity levels and pore sizes of the as-prepared samples increased with increasing the foaming agent content up to 1.0%, above which both porosity levels and pore sizes did not change. The compressive strength and flexural strength of the as-prepared sample with porosity of 76% and average pore size of 313 μm remained as high as 15.3±0.3 MPa and 3.7±0.2 MPa, respectively, and permeability increased exponentially with increasing the porosity.     

Porous SiC/SiCN composite ceramics fabricated by foaming and reaction sintering

Porous SiC/SiCN composite ceramics with heterogeneous pore structure and rod-like SiCN grains were fabricated by foaming and reaction sintering. The mixture slurry containing SiC and silicon as raw materials, cornstarch as binder, Y₂O₃ as sintering additive and an electrosteric dispersant was stirred with foams derived from pre-foaming using foaming agent. The casted green body was sintered at 1650 °C under nitrogen atmosphere. The results demonstrated that the porous SiC/SiCN ceramics exhibited hierarchical vias ranging from 1 μm to 1 mm and the rod-like crystalline SiCN grains generated in the SiC matrix.     

Foam-gelcasting preparation,microstructure and thermal insulation performance of porous diatomite ceramics with hierarchical pore structures

Hierarchically pore-structured porous diatomite ceramics containing 82.9∼84.5% porosity were successfully prepared for the first time via foam-gelcasting using diatomite powder as the main raw material. Sizes of mesopores derived from the raw material and macropores formed mainly from foaming were 0.02∼0.1 μm and 109.7∼130.5 μm, respectively. The effect of sintering temperature, additive content and solid loading of slurry on pore size and distribution, and mechanical and thermal properties of as-prepared porous ceramics were investigated. Compressive strength of as-prepared porous ceramics increased with sintering temperature, and the one containing 82.9% porosity showed the highest compressive strength of 2.1 ± 0.14 MPa. In addition, the one containing 84.5% porosity and having compressive strength of 1.1 ± 0.07 MPa showed the lowest thermal conductivity of 0.097 ± 0.001 W/(m·K) at a test temperature of 200 ̊C, suggesting that as-prepared porous ceramics could be potentially used as good thermal insulation materials.     

Effects of LiF on the microstructure and optical properties of hot-pressed MgAl2O4 ceramics

Transparent magnesium aluminate spinel (MgAl₂O₄) ceramics were fabricated by hot-pressing of the MgO and α-Al₂O₃ powder mixture using LiF as a sintering aid. Effects of the LiF additive on densification, microstructure and optical properties of MgAl₂O₄ ceramics were systematically investigated. It has been found that the addition of LiF can effectively remove the porosity and increase the optical transparency of MgAl₂O₄ ceramics. For the spinel ceramics HP-ed at 1550 °C for 3 h with 1 wt% LiF addition, the average grain size is about 36 µm and the in-line transmittance exceeds 60% at the wavelength of 800 nm.     

Preparation and properties of mullite-bonded porous fibrous mullite ceramics by an epoxy resin gel-casting process

Porous fibrous mullite ceramics with a narrow range of pore size distribution have been successfully prepared utilizing a near net-shape epoxy resin gel-casting process by using mullite fibers, Al₂O₃ and SiC as raw materials. The effects of sintering temperatures, different amounts of fibers and Y₂O₃ additive on the phase compositions, linear shrinkage, apparent porosity, bulk density, microstructure, compressive strength and thermal conductivity were investigated. The results indicated that mullite-bonded among fibers were formed in the porous fibrous mullite ceramics with a bird nest pore structure. After determining the sintering temperatures and the amount of fibers, the tailored porous fibrous mullite ceramics had a low linear shrinkage (1.36–3.08%), a high apparent porosity (61.1–71.7%), a relatively high compressive strength (4.4–7.6 MPa), a low thermal conductivity (0.378–0.467 W/m K) and a narrow range of pore size distribution (around 5 µm). The excellent properties will enable the porous ceramics as a promising candidate for the applications of hot gas filters, thermal insulation materials at high temperatures.     

Fabrication and characterization of cordierite-bonded porous SiC ceramics

A reaction bonding technique was used for the preparation of cordierite-bonded porous SiC ceramics in air from α-SiC, α-Al₂O₃ and MgO, using graphite as the pore-forming agent. Graphite was burned out to produce pores and the surface of SiC was oxidized to SiO₂ at high temperature. With further increasing the temperature, SiO₂ reacted with α-Al₂O₃ and MgO to form cordierite. SiC particles were bonded by the cordierite and oxidation-derived SiO₂. The reaction bonding characteristics, phase composition, open porosity, pore size distribution and mechanical strength as well as microstructure of porous SiC ceramics were investigated. The pore size and porosity were strongly dependent, respectively, on graphite particle size and volume fraction. The porous SiC ceramics sintered at 1350 °C for 2 h exhibited excellent combination properties, the flexural strength of 26.0 MPa was achieved at an open porosity of 44.51%.     

Foam-gelcasting preparation of high-strength self-reinforced porous mullite ceramics

High-strength self-reinforced porous mullite ceramics were prepared via foam-gelcasting using mullite powder as a main raw material, AlF₃·3H₂O (0–8 wt%) as an additive, Isobam-104 as a dispersing and gelling agent, sodium carboxymethyl cellulose as a foam stabilizing agent, and triethanolamine lauryl sulfate as a foaming agent. The effects of AlF₃·3H₂O content on rheological and gelling behaviors of the slurries, and porosity and mechanical properties of self-reinforced porous mullite samples were examined. Addition of AlF₃·3H₂O promoted the in-situ formation of elongated mullite in the fired porous samples, which improved considerably their mechanical properties. Compressive strength and flexural strength of 67.0% porous mullite ceramics prepared with addition of 6 wt% AlF₃·3H₂O was as high as 41.3 and 13.9 MPa, respectively. Its hot modulus rupture (HMOR) increased initially with the testing temperature, and peaked (with a maximum value of 16.6 MPa) at 800 °C above which it started to decrease with the testing temperature. Nevertheless, it was still retained as high as 6.7 and 2.8 MPa at 1200 and 1400 °C, respectively.     

Porous Si3N4 ceramics fabricated through a modified incomplete gelcasting and freeze-drying method

Porous Si₃N₄ ceramics were fabricated via incomplete gelcasting and freeze-drying method followed by pressureless sintering at 1690 ℃. The specific way used in this work was to slow down the gelling process of ceramic suspensions by stopping water evaporation. Since water was retained and further frozen before the suspensions were totally gelled in normal way, pore structure was modified. Compared to direct freeze-casting, the polymer framework generated by polymerization of organic components prevented ice crystals from growing to large sizes. Performance of porous ceramics can also be controlled by the gelling time. Further on, porous Si₃N₄ ceramics with controlled pore structures can be obtained without using other organic additives. The gelling agent used in this study is a copolymer of isobutylene and maleic anhydride (IBMA). The small addition amount was only 0.2 wt%, but could greatly change the microstructure as well as mechanical performance of porous ceramics.     

Capillary rise properties of porous mullite ceramics prepared by an extrusion method using organic fibers as the pore former

Porous mullite ceramics with unidirectionally oriented pores were prepared by an extrusion method to investigate their capillary rise properties. Rayon fibers 16.5 μm in diameter and 800 μm long were used as the pore formers by kneading with alumina powder, kaolin clay, China earthen clay and binder with varying Fe₂O₃ contents of 0, 5 and 7 mass%. The resulting pastes were extruded into cylindrical tubes (outer diameter (OD) 30–50 mm and inner diameter (ID) 20–30 mm), dried at room temperature and fired at 1500 °C for 4 h. The bulk densities of the resulting porous ceramics ranged from 1.31 to 1.67 g/cm³, with apparent porosities of 43.2–59.3%. The pore size distributions measured by Hg porosimetry showed a sharp peak at 10.0 μm in the sample without Fe₂O₃ and at 15.6 μm in the samples containing Fe₂O₃; these pores, which arose from the burnt-out rayon fibers, corresponded to total pore volumes ranging from 0.24 to 0.34 ml/g. SEM showed a microstructure consisting of unidirectionally oriented pores in a porous mullite matrix. Prismatic mullite crystals were well developed on the surfaces of the pore walls owing to the liquid phase formed by the Fe₂O₃ component added to color the samples. The bending strengths of the tubular samples ranged from 15.6 to 26.3 MPa. The height of capillary rise, measured under controlled relative humidities (RH) of 50, 65 and 85%, was greater in the ceramics containing Fe₂O₃ than in those without Fe₂O₃, especially in the thinner samples. The maximum capillary rise reached about 1300 mm, much higher than previously reported. This excellent capillary rise ability is thought to be due to the controlled pore size, pore distribution and pore orientation in these porous mullite ceramics.     

Investigating the effect of SPRM on mechanical strength and thermal conductivity of highly porous alumina ceramics

For recycling waste refractory materials in metallurgical industry, porous alumina ceramics were prepared via pore forming agent method from α-Al₂O₃ powder and slide plate renewable material. Effects of slide plate renewable material (SPRM) on densification, mechanical strength, thermal conductivity, phase composition and microstructure of the porous alumina ceramics were investigated. The results showed that SPRM effectively affected physical and thermal properties of the porous ceramics. With the increase of SPRM, apparent porosity of the ceramic materials firstly increased and then decreased, which brought an opposite change for the bulk density and thermal conductivity values, whereas the bending strength didn’t decrease obviously. The optimum sample A2 with 50 wt% SPRM introducing sintered at 1500 °C obtained the best properties. The water absorption, apparent porosity, bulk density, bending strength and thermal conductivity of the sample were 31.7%, 62.8%, 1.71 g/cm³, 47.1 ± 3.7 MPa and 1.73 W/m K, respectively. XRD analysis indicated that a small quantity of silicon carbide and graphite in SPRM have been oxidized to SiO₂ during the firing process, resulting in rising the porous microstructures. SEM micrographs illustrated that rod-like mullite grains combined with plate-like corundum grains to endow the samples with high bending strength. This study was intended to confirm the preparation of porous alumina ceramics with high porosity, good mechanical properties and low thermal conductivity by using SPRM as pore forming additive.     

Mechanical properties and microstructure of porous BN–SiO2–Si3N4 composite ceramics

Porous silicon nitride (Si₃N₄) ceramics incorporated with hexagonal boron nitride (h-BN) and silica (SiO₂) nanoparticles were fabricated by pressureless-sintering at relatively low temperature, in which stearic acid was used as pore-making agent. Bending strength at room and high temperatures, thermal shock resistance, fracture toughness, elastic modulus, porosity and microstructure were investigated in detail. The mechanical properties and thermal shock resistance behavior of porous Si₃N₄ ceramics were greatly influenced by incorporation of BN and SiO₂ nanoparticles. Porous BN–SiO₂–Si₃N₄ composites were successfully obtained with good critical thermal shock temperature of 800 °C, high bending strength (130 MPa at room temperature and 60 MPa at 1000 °C) and high porosity.     

Fabrication and electrochemical properties of SOFC single cells using porous yttria-stabilized zirconia ceramic support layer coated with Ni

A porous yttria-stabilized zirconia (YSZ) ceramic supported single cell with a configuration of porous YSZ support layer coated with Ni/Ni–Ce_0.8Sm_0.2O_1.9 (SDC) anode/YSZ/SDC bi-layer electrolyte/La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ cathode was fabricated. The porosity, mechanical strength, and microstructure of porous YSZ ceramics were investigated with respect to the amount of poly(methyl methacrylate) (PMMA) used as a pore former. Porous YSZ ceramics with 56 vol.% PMMA showed a mechanical strength of 24 ± 3 MPa and a porosity of 37 ± 1%. The electrochemical properties of the single cell employing the porous YSZ support layer were measured using hydrogen and methane fuels, respectively. The single cell exhibited maximum power densities of 421 mW/cm² in hydrogen and 399 mW/cm² in methane at 800 °C. Moreover, at a current density of 550 mA/cm², the cell maintained 91% of its initial voltage after operation in methane for 13 h at 700 °C.     

Preparation and properties of porous alumina ceramics with oriented cylindrical pores produced by an extrusion method

Porous alumina ceramics with unidirectionally-oriented pores were prepared by extrusion. Carbon fibers of 14 μm diameter and 600 μm length to be used as the pore-forming agent were kneaded with alumina, binder and dispersing agent. The resulting paste was extruded, dried at 110 °C, degreased at 1000 °C and fired at 1600 °C for 2 h. SEM showed a microstructure of dispersed highly oriented pores in a dense alumina matrix. The pore area in the cross section was 25.3% with about 1700 pores/mm². The pore size distribution of the fired body measured by Hg porosimetry showed a sharp peak corresponding to the diameter of the burnt-out carbon fibers. The resulting porous alumina ceramics with 38% total porosity showed a fracture strength of 171 MPa and a Young's modulus of 132 GPa. This strength is significantly higher than the reported value for other porous alumina ceramics even though the present pore size is much larger.     

Preparation of porous Y2SiO5 ceramics with relatively high compressive strength and ultra-low thermal conductivity by a TBA-based gel-casting method

Porous Y₂SiO₅ ceramics with relative high compressive strength (as high as 24.45 MPa) and ultra-low thermal conductivity (～0.08 W/m K) were successfully fabricated by a tert-butyl alcohol based gel-casting method. The formation mechanism of the 3D interconnected pores and the properties of the green body are discussed. The porosity, pore size, compressive strength and thermal conductivity could be controlled by varying the initial solid loading and the sintering temperature. When regulating the initial solid loading (from 20 to 50 wt%) and sintering temperature (from 1200 to 1500 °C), the porosity can be controlled between 47.74% and 73.93%, and the compressive strength and the thermal conductivity of porous Y₂SiO₅ ceramics varied from 3.34 to 24.45 MPa and from 0.08 to 0.55 W/m K, respectively. It should be noted that the porous Y₂SiO₅ ceramics with 30 wt% solid loading and sintering at 1400 °C had an open porosity of 61.80%, a pore size of 2.24 μm, a low room-temperature thermal conductivity of 0.17 W/m K and a relatively high compressive strength of 13.91 MPa, which make this porous Y₂SiO₅ ceramics suitable for applications in high-temperature thermal insulators.     

Recycling of harmful waste lead-zinc mine tailings and fly ash for preparation of inorganic porous ceramics

The porous ceramics were prepared by directly sintering of lead-zinc mine tailings and fly ash as the raw materials without any additional sintering and foaming agent. The effects of fly ash addition on the crystalline phases, pore structure, physical–chemical porosities and mechanical strength were investigated. The results showed that the bulk density decreased firstly and then increased while the porosity and water absorption presented the opposite tendency with the increase of fly ash content. Meanwhile, the chemical stability improved and the flexural strength had the same variation tendency of the bulk density. The phase evolution of sample with 60 wt% fly ash addition indicated that anorthite phase was formed at low temperature (1000 °C). The thermal behavior illustrated that the foaming process was initiated by the reaction of internal constituents in the lead-zinc mine tailings. Different pore structures indicated different foaming mechanisms that probably occurred at different temperatures. The porous ceramics with 60 wt% fly ash addition exhibited excellent properties, including bulk density of 0.93 g/cm³, porosity of 65.6%, and flexural strength of 11.9 MPa.     

Mechanical and dielectric properties of porous magnesium aluminate (MgAl2O4) spinel ceramics fabricated by direct foaming-gelcasting

Porous ceramic materials have been broadly applied in various fields due to their multifunctional properties. Optimization of their microstructural characteristics, such as pore morphology, total porosity, and pore size distribution, which determine various properties of the final products, is crucial to improve their performances and thus extend their applications. In this study, single-phase porous MgAl₂O₄ materials were fabricated by direct foaming–gelcasting. With an increase in the foam volume from 260 to 350 mL, the total porosity and pore size of the porous ceramic increased, and its microstructure varied from mostly closed cells to open cells containing interconnected large pores (40–155 μm) and small circular windows (10–40 μm) in the ceramic skeleton. The total porosity could be tailored from 84.91% to 76.08% by modulating the sintering temperature and foam volume and the corresponding compressive strengths were in the range of 2.8–15.0 MPa. The compressive strength exhibited a power-law relationship with the relative density with indices of approximately 3.409 and 3.439, respectively. Porous MgAl₂O₄ ceramics exhibited low dielectric constants in the range of 1.618–1.910 at room temperature, which are well matched with theoretical calculations on account of a modified Bruggeman model. The porous MgAl₂O₄ ceramics with good mechanical and dielectric properties controlled easily by various sintering temperatures and foam volumes are promising for practical applications.     

Influence of post-HIP temperature on microstructural and optical properties of pure MgAl2O4 spinel: From opaque to transparent ceramics

Transparent MgAl₂O₄ spinel ceramics were processed from sub-micrometric commercial powder by applying a two-step procedure: pressureless sintering under vacuum followed by hot isostatic pressing. To limit grain growth and to avoid secondary reactions or impurities, no additives or sintering aids were added to the powder. First, pressureless sintering at 1500 °C during 2 h under vacuum led to opaque samples due to a high level of porosity. To improve the optical quality of the MgAl₂O₄ ceramics and the in-line transmission in the visible range, a post-treatment by hot isostatic pressing was applied. Highly transparent ceramics were obtained after a post-treatment at 1800 °C for 10 h with an in-line transmission of 81% at 400 nm and 86% from 950 to 3000 nm for a thickness of 2 mm (98.8% of the theoretical transmission).     

Microstructure and properties of porous SiC ceramics by LPCVI technique regulation

A new gradient pore structure in porous SiC ceramics was fabricated by low pressure chemical vapor infiltration (LPCVI). Effects of deposition duration on the mechanical properties and permeability of porous SiC ceramics were investigated. Results demonstrated that pore diameter and shapes decreased from the surface to the interior along with LPCVI duration. Porous SiC ceramics with deposition duration of 160 h exhibited flexural strength of 48.05 MPa and fracture toughness of 1.30 MPa m^1/2, where 221% and 189% improvements were obtained compared to porous SiC ceramics without LPCVI, due to CVI-SiC layer strengthening effect. Additionally, at the same gas velocity, pressure drop increase rate was faster due to apparent porosity and pore size change.     

Preparation of porous Al2TiO5-Mullite ceramic by starch consolidation casting and its corrosion resistance characterization

Stabilized Al₂TiO₅ (AT)-mullite (M) porous ceramics were fabricated by starch consolidation casting using corn starch as curing agent and their microstructure, mechanical properties, pore size distribution and corrosion resistance were examined. Results showed that AT-M porous ceramic with the flexural strength of 11.5 MPa, apparent porosity of about 54.7% and pore size distribution in the range of 1–15 µm could be obtained with 10 wt% corn starch addition. Corrosion resistance results showed mass losses in hot H₂SO₄ solution and NaOH solution for 10 h to decreased from 1.03% to 0.36% and 4.39–2% when the calcination temperature increased from 1400 °C to 1450 °C, which proved these AT-M porous ceramics to possess an excellent corrosion resistance in acidic condition when calcined at 1450 °C.     

Effects of pore shape and porosity on the properties of porous PZT 95/5 ceramics

Porous lead zirconate titanate (PZT 95/5) ferroelectric ceramics were prepared by sintering compacts consisting of PZT and pore formers. The piezoelectric, dielectric and ferroelectric properties of porous PZT ceramics were investigated as a function of pore shape and porosity. Piezoelectric coefficient (d₃₃), dielectric constant (ɛ₃₃) and remnant polarization (P_r) decreased with an increase in porosity, and the porous PZT ceramics with spherical pores exhibited better properties than that with irregular pores. Furthermore, the electrical conductivities of PZT ceramics were investigated to explain the phenomena that porous PZT ceramics exhibited lower dielectric loss (tan δ) than dense PZT ceramics in the temperature range from 250 to 500 °C.