Enhancement of dielectric characteristics in donor doped Aurivillius SrBi2Ta2O9 ferroelectric ceramics

In this study, investigations have been made on the crystal structure, surface morphology, dielectric and electrical properties of tungsten doped SrBi₂(W_xTa_1−x)₂O₉ (0.0 ≤ x ≤ 0.20) ferroelectric ceramics. Dielectric measurements performed as a function of temperature at 1, 10 and 100 kHz show an increase in Curie temperature (T_c) over the composition range of x = 0.05–0.20. W⁶⁺ substitution in perovskite-like units results in a sharp dielectric transition at the ferroelectric Curie temperature with the dielectric constant at their respective Curie temperature increasing with tungsten doping. The dielectric loss reduces significantly with tungsten addition. The temperature dependence of ac and dc conductivity vis-à-vis tungsten content shows a decrease in conductivity, which is attributed to the suppression of oxygen vacancies. The activation energy calculated from the Arrhenius plots is found to increase with tungsten content.     

Influence of Ca substitution on microstructure and electrical properties of Ba(Zr,Ti)O3 ceramics

In the present work, lead-free (Ba_1?xCa_x)(Zr_0.04Ti_0.96)O₃ (x=0.00–0.09) ceramics were fabricated via a solid-state reaction method. The microstructure and electrical properties of the ceramics were investigated. The microstructure of the BCZT ceramics showed a core shell structure at compositions of x=0.03 and 0.06. The substitution of small amount of Ba²⁺ by Ca²⁺ resulted in an improvement of the piezoelectric, dielectric and ferroelectric properties of the ceramics. The orthorhombic–tetragonal phase transition was found in the composition of x≤0.03. Piezoelectric coefficient of d₃₃～392 pC/N and lowest E_c～3.3 kV/cm with highest P_r～14.1 μC/cm² were obtained for the composition of x=0.03 while its Curie temperature (T_C) was as high as 125 °C. However, the ferroelectric to paraelectric transition temperature had slightly shifted towards room temperature with increasing Ca²⁺ concentration.     

Effect of CuO addition on magnetic and electrical properties of Sr2Bi4Ti5O18 lead-free ferroelectric ceramics

The effect of CuO addition on magnetic and electrical properties of Sr₂Bi₄Ti₅O₁₈ (SBT) lead-free bismuth layered structure ferroelectric ceramics have been studied and reported. Interestingly, the prepared samples exhibit multiferroic behavior with the coexistence of magnetic and ferroelectric phase transition temperature. Magnetic phase transition with Neel׳s temperature (T_N) of 657 K is observed at 0.75 mol% of CuO added SBT ceramics, which is higher than the well known multiferroic BiFeO₃ (643 K) and the ferroelectric phase transition with Curie temperature (T_C) of 587 K is observed at 1 mol% of CuO added SBT ceramics, which is relatively higher than the reported pure SBT ceramics (558 K). Further, the electrical properties such as dielectric, ferroelectric, piezoelectric, leakage current density characteristics and optical properties were investigated as a function of x (x=0, 0.25, 0.5, 0.75 and 1 mol%). Presence of strong magnetic super-exchange interactions in CuO and the creation of oxygen vacancies play a vital role in the enhancement of magnetic and electrical properties of CuO doped SBT ceramics. Moreover, the present results indicate that, small amount (0.25 mol%) of CuO addition in SBT ceramics enhances the electrical properties significantly and vice versa, large amount (0.75 mol%) of CuO addition enhances the magnetic properties. Thus, the presence of magneto-electric coupling effect was observed in CuO doped Sr₂Bi₄Ti₅O₁₈ ferroelectric ceramics.     

Preparation and photoluminescence properties of Eu3+-doped ZrO2 nanotube arrays

Zr–Eu alloy containing 3 at% Eu was prepared by a powder metallurgical method and Eu³⁺-doped ZrO₂ nanotube arrays were prepared by anodising the Zr–Eu alloy. The properties of Eu³⁺-doped ZrO₂ nanotube arrays were studied in contrast to undoped ZrO₂ nanotube arrays under different annealing temperatures. Results showed that the Eu³⁺ ions could not only stabilise the tetragonal phase of zirconium oxide, but also make the crystallite sizes smaller. Annealing temperature exerted a significant influence on the absorbance value, as well as the intensity and position of the photoluminescence peaks. When the excitation wavelength was either 248 nm or 270 nm, the sample annealed at 600 °C displayed the strongest emission peak; while under excitation at 232 nm, the sample annealed at 400 °C exhibited the strongest emission peak.     

Tunable full color emission from single-phase LiSr3.99−xDy0.01(BO3)3:xEu3+ phosphors

Tunable full color emissive LiSr_3.99?xDy_0.01(BO₃)₃:xEu³⁺ (0≤x≤0.09) phosphors peaked at 481 nm (blue), 574 nm (yellow), 592 nm (orange), and 617 nm (red) were synthesized in air by high temperature solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), photoluminescence excitation (PLE) and photoluminescence (PL) spectra. The PLE spectra in the range from 200 to 500 nm include an Eu–O charge transfer band (CTB) and several 4f–4f transition peaks of Dy³⁺ and Eu³⁺, indicating its potential application in white light emitting diodes (LEDs). The effect of Eu³⁺ concentration on the emission intensity of LiSr_3.99?xDy_0.01(BO₃)₃:xEu³⁺ phosphors was investigated in detail and the optical concentration is found to be x=0.005. The CIE chromaticity coordinates for LiSr_3.99?xDy_0.01(BO₃)₃:xEu³⁺ phosphors are simulated. With an increase in Eu³⁺ ion concentration, the chromaticity color coordinates can be tuned efficiently from the border of greenish white region to its equal-energy white light point, and eventually to red region. All the results imply that the studied LiSr_3.99?xDy_0.01(BO₃)₃:xEu³⁺ phosphors could be potentially used as white LEDs.     

Processing and enhanced electrical properties of Sr1-x(K0.5Bi0.5)xBi2Nb2O9 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics, Sr_1−x(K_0.5Bi_0.5)_xBi₂Nb₂O₉ (SKBN-x, x=0, 0.2, 0.5, 1.0), were synthesized by a conventional solid-state reaction. Structural and electrical properties of SKBN-x ceramics were investigated. X-ray diffraction analysis suggested that the substitution led to the formation of a layered perovskite structure. Plate-like morphologies for the grains were clearly observed in all the samples, which are characteristic for layer-structure Aurivillius compounds. The Curie temperature (T_c) is found to shift to higher temperature from 445 °C to 509 °C with increasing (K, Bi) content. Excellent remanent polarization (2P_r∼15 μC/cm²) were obtained for SKBN-0.2 ceramic. High piezoelectric coefficient of d₃₃∼21  pC/N were obtained for the samples at x=0.5. Additionally, thermal annealing studies indicated that the piezoelectric coefficient (d₃₃) of SKBN-0.5 was unchanged even if annealing temperature increased to be 450 °C, demonstrating the ceramics are the promising candidates for high-temperature applications.     

Dielectric,ferroelectric and field-induced strain behavior of K0.5Na0.5NbO3-modified Bi0.5(Na0.78K0.22)0.5TiO3 lead-free ceramics

Lead-free piezoelectric (1 ? x)Bi_0.5(Na_0.78K_0.22)_0.5TiO₃–xK_0.5Na_0.5NbO₃ (BNKT–xKNN, x = 0–0.10) ceramics were synthesized using a conventional, solid-state reaction method. The effect of KNN addition on BNKT ceramics was investigated through X-ray diffraction (XRD), dielectric, ferroelectric and electric field-induced strain characterizations. XRD revealed a pure perovskite phase with tetragonal symmetry in the studied composition range. As the KNN content increased, the depolarization temperature (T_d) as well as maximum dielectric constant (?_m) decreased. The addition of KNN destabilized the ferroelectric order of BNKT ceramics exhibiting a pinched-type hysteresis loop with low remnant polarization (11 μC/cm²) and small piezoelectric constant (27 pC/N) at 3 mol% KNN. As a result, at x = 0.03 a significant enhancement of 0.22% was observed in the electric field-induced strain, which corresponds to a normalized strain (S_max/E_max) of ～434 pm/V. This enhancement is attributed to the coexistence of ferroelectric and non-polar phases at room temperature.     

Reduced dielectric loss and strain hysteresis in (0.97−x)BiScO3–xPbTiO3–0.03Pb(Mn1/3Nb2/3)O3 piezoelectric ceramics

(0.97−x)BiScO₃–xPbTiO₃–0.03Pb(Mn_1/3Nb_2/3)O₃ (BS–PT–PMnN) ceramics were prepared by solid-state reaction method. X-ray diffraction analysis revealed that the morphotropic phase boundary (MPB) of BS–PT–PMnN ceramics located near x=0.58. The high Curie temperature (437 °C), large piezoelectric constant (300 pC/N), low dielectric loss (0.015) and small strain hysteresis (20%) were obtained for the MPB composition. Its dielectric loss and strain hysteresis were reduced down to one third and half those of pure BiScO₃–PbTiO₃ (BS–PT) ceramics, respectively. In addition, the maximum vibration velocity of the BS–PT–PMnN ceramics was 0.85 ms⁻¹, much superior to those of BS–PT (0.15 ms⁻¹) and modified PZT (0.4 ms⁻¹) ceramics. These results indicated BS–PT–PMnN ceramics were promising candidates for high temperature piezoelectric applications.     

White light emitting from YVO4/Y2O3:Eu3+,Bi3+ composite phosphors for UV light-emitting diodes

A series of (1−x)YVO₄/xY₂O₃:Eu³⁺_0.006,Bi³⁺_0.006 (0≤x≤0.54) composite phosphors was synthesized in one step by high temperature solid state reaction and the photoluminescence properties were investigated. By means of co-doping Eu³⁺ and Bi³⁺ ions into the composite matrices composed of YVO₄ and Y₂O₃ crystals, the YVO₄/Y₂O₃:Eu³⁺,Bi³⁺ phosphor exhibits simultaneously the blue (418 nm), green (540 nm) and orange-red (595, 620 nm) emissions. The broad blue and green emissions are attributed to the ³P₁–¹S₀ transitions of Bi³⁺ ion both in Y₂O₃ and in YVO₄ matrices. Moreover, the sharp orange-red emissions are attributed to the ⁵D₀–⁷F_1,2 transitions of Eu³⁺ ion in YVO₄ matrix. By tuning the mole ratio of YVO₄/Y₂O₃ matrices the white light-emitting could be obtained. The results indicated that when the mole ratio of Y₂O₃ (x) is at 0.11–0.54 mol, the (1−x)YVO₄/xY₂O₃:Eu³⁺_0.006,Bi³⁺_0.006 phosphors emit white light by combining the blue, green and orange-red emissions under the excitation of 360–370 nm wavelength which matches the emission of the commercial UV-LED diode. This implies that the phosphors may be the promising white light materials with broad absorption band for white light-emitting diodes.     

Creating adjoining polymorphic phase transition (PPT) regions in ferroelectric (Ba,Sr)(Zr,Ti)O3 ceramics

In this work, we report the polymorphic phase transitions(PPT) in ferroelectric Ba_0.95Sr_0.05Zr_xTi_(1-x)O₃ (BSZT, x = 0.01–0.10) ceramics synthesized by using a solid-state reaction method. The doping elements and composition ratios were selected to create adjoining PPT phase boundaries near room temperature, hence to achieve a broadened peak of piezoelectric performance with respect to composition. The temperature-composition phase diagram was constructed and the effects of PPT on the electromechanical and ferroelectric properties of the ceramics were investigated. It was revealed that the two adjacent PPT regions at room temperature showed different characteristics in property enhancement. However, due to the proximity of the phase boundaries, Ba_0.95Sr_0.05Zr_xTi_(1-x)O₃ ceramics in a fairly broad range of compositions (0.02 ≤ x ≤ 0.07) showed excellent piezoelectric properties, including a large piezoelectric constant (312 pC/N ≤ d₃₃ ≤ 365 pC/N) and a high electromechanical coupling coefficient k_p (0.42 ≤ k_p ≤ 0.49).     

Synthesis and characterizations of KNN ferroelectric ceramics near 50/50 MPB

Lead free ferroelectric ceramics near the morphotropic phase boundary (MPB) of K_xNa_1?x(NbO₃)/KNN system (where x=0.48, 0.50, 0.52) were synthesized in the single perovskite phase by the partial co-precipitation synthesis route. The compositional dependences of phase, structure and electrical properties were studied in detail. X-ray diffraction (XRD) study revealed the coexistence of orthorhombic and monoclinic structures in K_0.50N_0.50NbO₃. SEM characterization of the sintered KNN ceramics revealed dense and homogeneous packing of grains. Room temperature (RT) dielectric constant (ε_r) ～648, dielectric loss (tan δ) ～0.05 at 100 kHz, a relatively high density (ρ) ～4.49 g/cm³, remnant polarization (P_r) ～11.76 μC/cm², coercive field (E_c) ～9.81 kV/cm, Curie temperature (T_c) ～372 °C and piezoelectric coefficient (d₃₃) ～71 pC/N observed in K_0.50N_0.50NbO₃ suggested that it can be an important lead free ferroelectric material.     

Strong photoluminescence and piezoelectricity properties in Pr-doped Ba(Zr0.2Ti0.8)O3–(Ba0.7Ca0.3)TiO3 ceramics: Influence of concentration and microstructure

(Ba_0.85Ca_0.15)_1−xPr_x(Zr_0.1Ti_0.9)O₃ (where 0 < x < 0.01, abbreviated as BCZT:xPr) ceramics were fabricated by conventional solid-state reaction method. The influence of dopant concentration and microstructure on photoluminescence, ferroelectric, and piezoelectric properties was systematically investigated. The results showed that the photoluminescence spectra of the samples exhibited strong green (530 nm) and red (602 nm) emissions upon excitation of the 430 nm to 500 nm light, which couples well with to the emission band of the commercial blue light-emitting diodes chips. The emission intensities were strongly dependent on the dopant concentration and crystallite size, which reached the optimal value when the crystallite size and dopant concentration were 8 μm and 0.002 mol, respectively. Meanwhile, a large piezoelectric response with d₃₃ = 325 pC/N was obtained for BCZT:0.002Pr near the morphotropic phase boundary. Therefore, the Pr-doped BCZT materials, simultaneously exhibiting excellent luminescent properties and high piezoelectric properties, may have significant technological promise in novel multifunctional devices.     

A new route for the synthesis of β-sialon: Eu2+ phosphors using pyrophyllite powders

Eu²⁺ ion doped β-sialon (Si_6?zAl_zO_zN_8?z:xEu²⁺) phosphors were prepared from pyrophyllite-based mixtures by a carbothermal reduction and nitridation method first. Then, the effects of z values and the Eu concentration on the structure and the photoluminescence (PL) properties were investigated. β-Sialon was successfully synthesized as a dominant phase even at the low temperature of 1500 °C, while Si₃N₄ and AlN weakly coexisted as secondary phases. The PL excitation spectra exhibited the broad spectra covering up to 500 nm, and the greenish-yellow emission was observed at around 580 nm. At z=1 and x=0.012, excellent emission intensity could be attained.     

Phase structure,piezoelectric, ferroelectric,and electric-field-induced strain properties of Nb-modified 0.8Bi0.5Na0.5TiO3−0.2Sr0.85Bi0.1TiO3 ceramics

0.8Bi_0.5Na_0.5Ti_(1-x)Nb_xO₃−0.2Sr_0.85Bi_0.1TiO₃ (BNT-SBT-xNb, x = 0.00, 0.01, 0.02, and 0.03) piezoelectric ceramics were prepared by traditional solid state reaction and the influence of Nb substitution on the phase structure, ferroelectric, piezoelectric, and electric-field-induced strain properties in BNT-SBT ceramics were studied. XRD results exhibited that Nb⁵⁺ ions could fully diffuse into BNT-SBT structure to form a solid solution when x = 0.01. P-E loops and S-E curves suggested that the ferroelectric phase transformed to ergodic relaxor state (FE-to-ER) with the increasing the amount of Nb additive, indicating the ferroelectric long-ranged order was disturbed by the excess of Nb. With increasing Nb doping, phase transition temperature from normal ferroelectric to ergodic relaxor (short for T_F-R) could be reduced from 120 °C to 40 °C. Furthermore, for sample with x = 0.01, the normalized strain d₃₃^* got a maximum value ~571 pm/V due to the phase transition from ergodic relaxor to ferroelectric (ER-to-FE) under electric field.     

Low-temperature sintering and electrical properties of (K,Na)NbO3 based lead-free ceramics with high Curie temperature

Lead-free ceramics (1 ? x)(K_0.48Na_0.52)NbO₃–(x/5.15)K_2.9Li_1.95Nb_5.15O_15.3 (x = 0.3–0.6, KNN–KLN100x) were prepared by conventional sintering technique at a low temperature of 960 °C. The effects of KLN contents on microstructure, dielectric, and piezoelectric properties were investigated. After the addition of KLN, the sintering performance and Curie temperature of the ceramics were markedly improved. The ceramics with x = 0.3 exhibited very good piezoelectric properties: d₃₃ = 138 pC/N, k_p = 45.03%, T_c = 495 °C, the dielectric constant at room temperature ?_r (RT) = 478 and the maximum dielectric constant ?_r (max) = 5067. These results indicated that the KNN–KLN100x lead-free ceramics sintered at low temperatures are promising for high temperature piezoelectric applications.     

High performance Aurivillius-type bismuth titanate niobate (Bi3TiNbO9) piezoelectric ceramics for high temperature applications

This paper reports the significant improved piezoelectric properties of high temperature bismuth titanate niobate (Bi₃TiNbO₉, BTN) polycrystalline ceramics. The piezoelectric performance of BTN ceramics is significantly enhanced by cerium modifications. The dielectric measurements indicate that the Curie temperature T_c gradually decreases over the temperature range of 907–889 °C with cerium contents increasing up to 0.7 wt%. The BTN-5Ce (BTN+0.5 wt% CeO₂) exhibits optimized piezoelectric properties with a piezoelectric constant d₃₃ of 16 pC/N, which is five times the value of unmodified BTN (d₃₃~3 pC/N), while BTN-5Ce maintains a high Curie temperature T_c of 894 °C. The temperature-dependent electrical impedance and electromechanical coupling factors (k_p, and k_t) reveal that the BTN-5Ce exhibits thermally stable electromechanical coupling characteristics up to 500 °C but significantly deteriorates at 600 °C due to high conductivity at a higher temperature. The thermally stable electromechanical properties in combination with the ceramics׳ high electrical resistivity (10⁶ Ω cm at 500 °C) and high Curie temperature (~900 °C) demonstrate that cerium-modified BTN ceramics are good materials for high temperature sensing applications.     

Enhanced microstructure and electrical properties of Mn-modified Bi0.5(Na0.65K0.35)0.5TiO3 ferroelectric ceramics

Bi_0.5(Na_0.65K_0.35)_0.5TiO₃ (BNKT) and Mn-modified Bi_0.5(Na_0.65K_0.35)_0.5(Mn_xTi_1−x)O₃ (BNKMT-10³x), (x=0.0–0.5%) ferroelectric ceramics were synthesized by solid-state reaction method. Optimization of calcination temperature in Mn-doped ceramics was carried out for the removal of secondary phases observed in XRD analysis. BNKMT ceramics sintered at 1090 °C showed enhanced dielectric, piezoelectric and ferroelectric properties in comparison to pure BNKT. The average grain size was found to increase from 0.35 μm in BNKT to 0.52 μm in Bi_0.5(Na_0.65K_0.35)_0.5(Mn_0.0025Ti_0.9975)O₃ (BNKMT-2.5) ceramics. The dielectric permittivity maximum temperature (T_m) was increased to a maximum of 345 °C with Mn-modification. AC conductivity analysis was performed as a function of temperature and frequency to investigate the conduction behavior and determine activation energies. Significant high value of piezoelectric charge coefficient (d₃₃=176 pC/N) was achieved in BNKMT 2.5 ceramics. Improved temperature stability of ferroelectric behavior was observed in the temperature dependent P–E hysteresis loops as a result of Mn-incorporation. The fatigue free nature along with enhanced dielectric and ferroelectric properties make BNKMT-2.5 ceramic a promising candidate for replacing lead based ceramics in device applications.     

Effect of Nd substitution on the microstructure and electrical properties of Bi7Ti4NbO21 piezoceramics

Neodymium (Nd) doped intergrowth bismuth layer-structured ferroelectric compounds Bi_7?xNd_xTi₄NbO₂₁ (x = 0, 0.5, 0.75, 1.0, 1.25, 1.5, 1.75 and 2.0) were synthesized through a solid-state method. The influence of the Nd³⁺ substitution of Bi³⁺ on the lattice, microstructure and electrical properties of these compounds were investigated. The X-ray diffraction and Raman scattering analyses demonstrate that a phase transition from orthorhombic to pseudo-tetragonal occurs in these compounds, relying on substitution proportions and sites of Nd³⁺ for Bi³⁺. With the increasing Nd³⁺ dopants, the growth of plate-like grains along the a–b plane and a secondary intergranular metallic Bi phase were retarded which resulted in the increases of sintering temperature, density and electrical resistance of the doped ceramics. The resultant ceramic with x = 1.25 possesses a piezoelectric coefficient d₃₃ up to 16.3 pC/N with a Curie temperature T_C above 750 °C were obtained for the compound.     

Self-crystallized Ba2LaF7:Nd3+/Eu3+ glass ceramics for optical thermometry

Eu³⁺/Nd³⁺-codoped Ba₂LaF₇ transparent bulk glass ceramics were successfully fabricated by glass self-crystallization. The structure and morphology of the sample were investigated by X-ray diffraction, transmission electron microscopy (TEM), high-resolution TEM, and selected area electron diffraction. The fluorescence intensity ratios of Nd³⁺ emission at 800 nm to the Eu³⁺ emission at 699 nm (⁵D₀ → ⁷F₄) were measured under 578.3 nm laser excitation in a wide temperature range from 290 to 740 K. A relatively good temperature sensing performance was obtained with a maximum relative sensitivity of 1.02% K⁻¹ at 420 K. Both the emission peaks for temperature sensing were located in the optical window of biological tissue, which is favorable for biomedical applications. The results indicate that Ba₂LaF₇:Nd³⁺/Eu³⁺ glass ceramics have a potential application as temperature probes.     

The influence of Mo6+ doping on the luminescence properties of red-emitting phosphor Sr9Eu2W4−xMoxO24 (x = 0–4)

A series of red emitting phosphors Sr₉Eu₂W_4?xMo_xO₂₄ (x = 0–4) have been synthesized by solid-state reactions and their crystal structures, photoluminescence properties were studied. The excitation and emission spectra of Sr₉Eu₂W_4?xMo_xO₂₄ phosphors can be modified by Mo⁶⁺ doping. As the molybdate content increased, the Eu³⁺ emission intensity of Sr₉Eu₂W_4?xMo_xO₂₄ (x = 0–4) under 395 nm excitation was found to increase and reached a maximum at x = 2. The excitation spectra, the emission intensities and the chromaticity coordinates of Sr₉Eu₂W_4?xMo_xO₂₄ (x = 2) were compared to those of the conventional red phosphor Y₂O₂S: Eu³⁺. The intense red-emission under near-UV excitation suggests that Sr₉Eu₂W_4?xMo_xO₂₄ (x = 2) could be a potential candidate for white light generation by using near-UV LEDs. In this study, the effects of Mo⁶⁺ doping on the crystal structure and photoluminescence properties of Sr₉Eu₂W_4?xMo_xO₂₄ were discussed.