Mechanical properties and microstructures of 2D Cf/ZrC–SiC composites using ZrC precursor and polycarbosilane

Two-dimensional C_f/ZrC–SiC composites were fabricated through mold-pressing and polymer infiltration and pyrolysis (PIP) using T700SC plain weave fiber fabrics as reinforcements with ZrC precursor and polycarbosilane. The mechanical properties and microstructures of the composites with 34, 45, and 56% fiber fraction were investigated. All composites showed a typical non-brittle fracture behavior and a large amount of pulled-out fibers were observed on the fracture surface. The bending strength and elastic modulus of the composite with 56 vol% fiber fraction increased up to 582 ± 80 MPa and 167 ± 25 GPa, with increasing fiber fraction. The mass loss and linear recession rate of the composites during the oxy-propane torch test were 0.008 g/s and ?0.003 mm/s, respectively. The formation of a ZrSiO₄ melt on the surface of the composite significantly contributed to the excellent ablative property of the 2D C_f/ZrC–SiC composites.     

Mechanical behaviour and microstructure of Cf/ZrC,Cf/SiC and Cf/ZrC – SiC composites

Cf/ZrC, Cf/SiC and Cf/ZrC–SiC composites were successfully prepared by polymer infiltration and pyrolysis (PIP) using polycarbosilane and a liquid ZrC precursor. The densification process, mechanical properties and microstructures were studied in a view of comparison. After the same total 20 PIP cycles, the Cf/ZrC, Cf/SiC and Cf/ZrC–SiC composites had flexural strengths of 50.1±5.3, 285.7±22.6, 141.5±13.1?MPa respectively; elastic moduli of 7.8±0.9, 57.1±3.2 and 45.1±2.6?GPa respectively; and fracture toughness of 2.5±0.2, 10.4±0.9 and 10.9±1.1?MPa m^1/2 respectively. With the introduction of high modulus SiC phase into the ZrC matrix, the densification and modulus of the matrix were improved; as a result, the Cf/ZrC–SiC composite showed higher mechanical properties compared to Cf/ZrC.     

Effect of zirconia content on mechanical and thermal properties of mullite–zirconia composite

Abstract

Mullite–zirconia composites were prepared by adding various zirconia contents in the mullite ranging from 0 to 30 wt-% and sintering at 1400–1600°C for 2 h. The phase composition examined by X-ray diffraction showed that mullite was the major phase combined with developed t-ZrO₂ and m-ZrO₂ phase as a function of zirconia content, especially at 1600°C, wherein m-ZrO₂ predominated. Density increased when the zirconia content and sintering temperature were increased ranging from 2·2 to 3·53 g cm^?3. The morphology of mullite grain showed elongated grains, whereas dispersed zirconia showed equiaxed and intergranular grains. Flexural strength was continuously improved by adding zirconia during the sintering temperature ranging from 1400 to 1500°C, whereas flexural strength was initially improved up to 5 wt-% of zirconia addition and deteriorated with more than 5 wt-% of zirconia content during sintering between 1550 and 1600°C. The maximum strength, 190 MPa, was obtained when sintering mullite with 30 wt-% of zirconia content at 1500°C. The degradation of strength at high sintering temperature may be a result from more occurrence of m-ZrO₂ phase. Thermal expansion of sintered specimens indicated linear change and hysteresis loop change. The hysteresis loop obtained with increased zirconia content resulted in the t–m phase transformation. Martensitic start temperature M_s was determined to be 530°C for 15 wt-% zirconia sintered at 1500°C, implying that the t–m phase transformation occurred.     

Enhanced mechanical and microwave-absorption properties of SiCf/AlPO4 composite with PIP–SiC interphase and the MWCNTs filler

A single-layer radar-absorbing structure in the X-band (8.2 GHz to 12.4 GHz) was designed and fabricated by blending multi-walled carbon nanotubes (MWCNTs) with the binder matrix of SiC fiber/aluminum phosphate matrix (SiC_f/AlPO₄) composite. The SiC interphase was successfully prepared on SiC fibers by a precursor infiltration and pyrolysis (PIP) method. The morphology of as-received interphase was observed by SEM, and its structure was characterized by XRD and Raman spectrum. The effects of PIP–SiC interphase on the mechanical and dielectric properties of the composite were investigated. The influence of MWCNTs content on the dielectric and microwave-absorption properties of coated SiC_f/AlPO₄ composite was discussed. When the content of MWCNTs was between 1.5 wt% and 3.5 wt% and the composite thickness is in the range of 2.5–3.5 mm, the SiC_f/AlPO₄ composite achieved excellent absorbing wave property in X-band.     

Densification,microstructure, and mechanical properties of ZrC–SiC ceramics

ZrC–SiC ceramics were fabricated by high-energy ball milling and reactive hot pressing of ZrH₂, carbon black, and varying amounts of SiC. The ceramics were composed of nominally pure ZrC containing 0 to 30 vol% SiC particles. The relative density increased as SiC content increased, from 96.8% for nominally pure ZrC to 99.3% for ZrC-30 vol% SiC. As SiC content increased from 0 to 30 vol%, Young's modulus increased from 404 ± 11 to 420 ± 9 GPa and Vickers hardness increased from 18.5 ± 0.7 to 23.0 ± 0.5 GPa due to a combination of the higher relative density of ceramics with higher SiC content and the higher Young's modulus and hardness of SiC compared to ZrC. Flexure strength was 308 ± 11 MPa for pure ZrC, but increased to 576 ± 49 MPa for a SiC content of 30 vol%. Fracture toughness was 2.3 ± 0.2 MPa·m^1/2 for pure ZrC and increased to about 3.0 ± 0.1 MPa·m^1/2 for compositions containing SiC additions. The combination of high-energy ball milling and reactive hot pressing was able to produce ZrC–SiC ceramics with sub-micron grain sizes and high relative densities with higher strengths than previously reported for similar materials.     

Influence of graphite nano-flakes on densification and mechanical properties of hot-pressed ZrB2–SiC composite

Hot pressed monolithic ZrB₂ ceramic (Z), ZrB₂–20 vol% SiC composite (ZS₂₀) and ZrB₂–20 vol% SiC–10 vol% nano-graphite composite (ZS₂₀G_n10) were investigated to determine the influence of graphite nano-flakes on the sintering process, microstructure, and mechanical properties (Vickers hardness and fracture toughness) of ZrB₂–SiC composites. Hot pressing at 1850 °C for 60 min under 20 MPa resulted in a fully dense ZS₂₀G_n10 composite (relative density: 99.6%). The results disclosed that the grain growth of ZrB₂ matrix was efficiently hindered by SiC particles as well as graphite nano-flakes. The fracture toughness of ZS₂₀G_n10 composite (7.1 MPa m^1/2) was essentially improved by incorporating the reinforcements into the ZrB₂ matrix, which was greater than that of Z ceramic (1.8 MPa m^1/2) and ZS₂₀ composite (3.8 MPa m^1/2). The fractographical observations revealed that some graphite nano-flakes were kept in the ZS₂₀G_n10 microstructure, besides SiC grains, which led to toughening of the composite through graphite nano-flakes pull out. Other toughening mechanisms such as crack deflection and branching as well as crack bridging, due to the thermal residual stresses in the interfaces, were also observed in the polished surface.     

Architectural engineering inspired method of preparing Cf/ZrC–SiC with graceful mechanical responses

Inspired by grouting technique in architectural engineering, an innovative method of slurry injection and vacuum impregnation was put forward to introduce nanosized ZrC–SiC ceramics into PyC modified 3-D needle-punched carbon fiber preform homogeneously and continuously, followed by spark plasma sintering to prepare C_f/ZrC–SiC with graceful mechanical responses. The composite possessed improved fracture toughness and work of fracture at 5.37 ± 0.25 MPa∙m^1/2 and 951 ± 12 J/m², 50% and nearly one order of magnitude higher than those of ZrC–SiC composite, respectively, with rivaling flexural strength at 177 ± 8 MPa synchronously. A graceful fracture mode was embodied in an obviously extended yield plateau with increased failure displacement by 300%. This enhancement was attributed to the uniform and continuous combination of ZrC–SiC with carbon fiber preform as well as protection and interface tailoring from PyC coating. The study offered an easy and effective method of preparing 3-D fiber reinforced ceramic matrix composites.     

Heat treatment effects on microstructure and mechanical properties of CVI SiCf/PyC/SiC composites with Cansas-Ⅲ SiC fibers

The microstructure and mechanical properties of CVI-Cansas-III/PyC/SiC composites were systematically investigated after heat treatment under high temperature argon atmosphere, ranging from 1000 °C to 1500 °C, for different time durations. The results showed that the Cansas-III fibres degraded with increasing heat treatment temperature, resulting in degradation of the fibre properties due to pyrolysis of the SiOC phase inside the fibres. The bending strength of the composites remained nearly constant upon heat treatment at 1000 °C and 1250 °C, while a decline in bending strength was observed upon increasing the heat treatment temperature and time, specifically at 1350 °C and above. Moreover, the composites maintained their pseudo-plastic fracture behaviour below 1450 °C, while displaying brittle fracture of the ceramic after 100 h of heat treatment at 1500 °C, due to the complete crystallisation of the fibres.     

Effects of high-temperature annealing on the microstructure and properties of C/SiC–ZrC composites

C/SiC–ZrC composites were prepared by a combining slurry process with precursor infiltration and pyrolysis, and then annealed from 1200 °C to 1800 °C. With rising annealing temperature, their mass loss rate increased, and the flexural strength and modulus decreased from 227.9 MPa to 41.3 MPa and from 35.3 GPa to 22.7 GPa, respectively. High-temperature annealing, which elevated thermal stress and strengthened interface bonding, was harmful to the flexural properties. However, it improved the ablation properties by increasing the crystallization degree of SiC matrix. The mass loss rate and linear recession rate decreased with increasing annealing temperature and those of the samples annealed at 1800 °C were 0.0074 g/s and 0.0011 mm/s respectively. Taking mechanical and ablation properties into consideration simultaneously, the optimum annealing temperature was 1600 °C.     

Microstructure,mechanical and anti-ablation properties of SiCnw/PyC core-shell networks reinforced C/C–ZrC–SiC composites fabricated by a multistep method of chemical liquid-vapor deposition

C/C–ZrC–SiC composites reinforced by SiC nanowire (SiCnw)/pyrocarbon (PyC) core-shell networks were prepared by a multistep method of chemical liquid-vapor deposition (CLVD). The microstructure, mechanical property and ablation resistance were researched. The investigations presented that the PyC was deposited on the SiC nanowires, and the micro-scale core-shell structures were produced. Moreover, these micro-scale structures not only connected with the fibers and matrices, but also filled the pores in the composites. In contrast with C/C–ZrC–SiC composites, the flexural modulus and strength of SiCnw/PyC-C/C–ZrC–SiC composites increased by 36.91% and 44.53%, and the fracture mode was changed from the brittle to pseudo-plastic fracture. After the oxyacetylene torch ablation at two temperatures for 90s, the composites strengthened by SiCnw/PyC core-shell possessed a better resistant ablation. At ablation temperature of 2300 °C, the mass loss rate and linear reduction rate of the composites with core-shell networks decreased by 66.18% and 57.55% in contrast with the non-reinforced composites, and declined by 56.46% and 57.48% at ablation temperature of 3000 °C. The obvious decrease of ablation rates was ascribed to the dense microstructure, the small coefficient of thermal expansion (CTE), the good thermal conductivity, and the resistant ablation roles of SiCnw/PyC core-shell systems.     

Effect of ZrC content on the properties of biomorphic C–ZrC–SiC composites prepared using hybrid precursors of novel organometallic zirconium polymer and polycarbosilane

A novel organometallic zirconium polymer was synthesized through the copolycondensation using n-butyllithium, 1,4-diethynylbenzene, phenylacetylene and zirconium tetrachloride as raw materials. Then biomorphic C–ZrC–SiC composites were fabricated from corn stover templates by precursor infiltration and pyrolysis process using hybrid polymeric precursors containing the organometallic zirconium polymer and polycarbosilane. The microstructure, mechanical properties and oxidation resistance of the composites were investigated. With ZrC content increasing, the mechanical properties of the composites were enhanced due to dispersion strengthening and grain fining of the homogeneously dispersed ZrC nanoparticles. The oxidation behavior of C–SiC–ZrC indicated that the oxidation resistance of the composite was reduced at 1000 °C but improved at 1500 °C with the increase of ZrC content. The improved oxidation resistance was mainly attributed to a proper ZrC content, the formation of ZrSiO₄ layer on the surface of the composite, and its matrix microstructure characterized by a nano-sized dispersion of ZrC–SiC phases.     

Effect of heat treatment on the mechanical properties of PIP–SiC/SiC composites fabricated with a consolidation process

Continuous SiC fiber reinforced SiC matrix composites (SiC/SiC) have been considered as candidates for heat resistant and nuclear materials. Three-dimensional (3D) SiC/SiC composites were fabricated by the polymer impregnation and pyrolysis (PIP) method with a consolidation process, mechanical properties of the composites were found to be significantly improved by the consolidation process. The SiC/SiC composites were then heat treated at 1400 °C, 1600 °C and 1800 °C in an inert atmosphere for 1 h, respectively. The effect of heat treatment temperature on the mechanical properties of the composites was investigated, the mechanical properties of the SiC/SiC composites were improved after heat treatment at 1400 °C, and conversely decreased with increased heat treatment temperature. Furthermore, the effect of heat treatment duration on the properties of the SiC/SiC composites was studied, the composites exhibited excellent thermal stability after heat treatment at 1400 °C within 3 h.     

Fabrication and mechanical properties of laminated HfC–SiC/BN ceramics

Laminated HfC–SiC/BN ceramics were successfully fabricated by tape casting and hot pressing. Fully dense HfC–SiC ultra-high temperature ceramics with homogeneous structure were obtained. The introduction of the weak BN layer resulted in a slight decrease of the flexural strength but significantly improved the fracture toughness compared with monolithic HfC–SiC ceramics. The fracture toughness of laminated HfC–SiC/BN ceramics in the parallel direction peaked at 8.06 ± 0.46 MPa m^1/2, which increased by 115% than that of monolithic HfC–SiC ceramics. The composites showed non-catastrophic fracture behaviors in both parallel and perpendicular directions. It indicates that laminated structure design is a promising approach to obtain full density HfC–SiC ceramics with high fracture toughness.     

Fiber/matrix interfacial shear strength of C/C composites with PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers

The fiber/matrix (F/M) interfacial shear strength (IFSS) of carbon/carbon (C/C) composites with PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers was investigated. To obtain C/C composites with PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers, a thin layer of PyC was deposited on carbon fibers. After this, TaC and SiC–TaC layer(s) were uniformly deposited on the PyC coated carbon fibers. As an outer-layer, a PyC layer was deposited on these TaC and/or SiC–TaC coated carbon fibers by isothermal chemical vapour infiltration (CVI) and then densified with resin carbon by impregnation and carbonization. Finally, C/C composites with PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers were obtained. The effects of PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers on interfacial shear strength (IFSS) of C/C composites were investigated. Single fiber push-out tests were conducted on the fibers aligned perpendicularly on the thin slices specimen surface using nano-indentation. Results showed that the IFSS of C/C composites decreased with the introduction of PyC–TaC–PyC and PyC–SiC–TaC–PyC multi-interlayers. After heat treatment (at temperatures ranging from 1400 to 2500 °C) of C/C composites with PyC–TaC–PyC multi-interlayers, it was found that the IFSS decreased with the increase in temperature. This decrease in IFSS is explained by taking into account the microstructural variations on heat treatment.     

Effects of porous C/C density on the densification behavior and ablation property of C/C–ZrC–SiC composites

C/C–ZrC–SiC composites were prepared by precursor infiltration and pyrolysis process using a mixture solution of organic zirconium-containing polymer and polycarbosilane as precursors. Porous carbon/carbon (C/C) composites with density of 0.92, 1.21 and 1.40 g/cm³ were used as preforms, and the effects of porous C/C density on the densification behavior and ablation resistance of C/C–ZrC–SiC composites were investigated. The results show that the C/C preforms with a lower density have a faster weight gain, and the obtained C/C–ZrC–SiC composites own higher bulk density and open porosity. The composites fabricated from the C/C preforms with a density of 1.21 g/cm³ exhibit better ablation resistance with a surface temperature of over 2400 °C during ablation. After ablation for 120 s, the linear and mass ablation rates of the composites are as low as 1.02 × 10⁻³ mm/s and −4.01 × 10⁻⁴ g/s, respectively, and the formation of a dense and continuous coating of molten ZrO₂ solid solution is the reason for their great ablation resistance.     

Effect of nanocarbon sources on microstructure and mechanical properties of MgO–C refractories

A study of microstructural evolution, mechanical and thermo-mechanical properties of MgO–C refractories, based on graphite oxide nanosheets (GONs), carbon nanotubes (CNTs) and carbon black (CB), was carried out by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS), three-point bending and thermal shock tests. Meanwhile, these results were compared to the conventional MgO–C refractory containing 10 wt% flaky graphite prepared under the same conditions. The results showed that higher cold modulus of rupture was obtained for the composition containing GONs, and the composition containing CNTs exhibited larger displacement after coking at 1000 °C and 1400 °C. Also, the addition of nanocarbons led to an improvement of the thermal shock resistance; in particular, both compositions containing CNTs and CB had higher residual strength ratio, approaching the thermal shock resistance of the reference composition containing 10 wt% flaky graphite, as it was associated with the presence of nanocarbons and in-situ formation of ceramic phases in the matrix.     

Effect of SiC on the corrosion resistance of electroless Cu–P–SiC composite coating

In this work, Cu–P–SiC composite coatings were deposited via electroless plating with the addition of sodium hypophoshite (NaH₂PO₂) as a reducing agent. The coating compositions deposited were determined by using energy dispersive X-ray spectroscopy (EDX). The surface morphology of the coatings that were analyzed using scanning electron microscopy (SEM) showed that SiC particles were uniformly distributed by virtue of surfactant addition and mechanical stirring. The anti-corrosion properties of Cu–P and Cu–P–SiC coatings in NaCl and HCl solutions were investigated by the weight loss and potentiodynamic polarization techniques. The results showed that the corrosion resistance of Cu–P–SiC coatings was superior to that of electroless Cu–P coatings and carbon steel substrates in various concentrations of NaCl and HCl solutions.     

Fabrication and characterization of biomorphic cellular C/SiC–ZrC composite ceramics from wood

Biomorphic cellular C/SiC–ZrC composite ceramics were fabricated from pine and oak wood precursors. Carbonaceous preforms were first prepared by wood pyrolysis and subsequently infiltrated with polyzirconobutanediol (PZC) and polycarbosilane (PCS) to form the composite ceramics. TGA/DTG and dilatometric analysis were used to study the pyrolysis of the wood precursor. XRD and SEM analyses were applied to characterize the microscopic properties of the resulting biomorphic cellular C/SiC–ZrC composite ceramics. Compared with oak, pine was preferable for preparation of cellular C/SiC–ZrC composite ceramics because of its unique microstructure. The SiC–ZrC phase distribution differed within the composite ceramics. In addition, the compression strengths of wood, charcoal, and cellular C/SiC–ZrC composite ceramics were measured in the axis direction. Results showed the improved compression strength of biomorphic cellular C/SiC–ZrC composite ceramics when the impregnation cycles were repeated.     

Multiscale investigation on fatigue properties and damage of a 3D braided SiC/SiC + PyC/SiC composites in the full stress range at 1300 °C

Monotonic tensile and fatigue tests of a SiC/SiC composites were conducted at 1300 °C in the full stress range. The macroscopic behaviors were studied based on the strain data. The mesoscopic morphology was observed by X-ray computed tomography, and the microanalysis was conducted using SEM, EDS and XRD. Besides, the interfacial debonding strength (IDS) were measured by nano-indenter. The results reveal that the fatigue behaviors can be divided into three zones. The inelastic strains accumulation and stiffness reduction can be observed in all three zones due to matrix cracking, interface damage, and failure of fibers. The fatigue life is long in the run-out zone because the maximum stress is lower than the proportional limit stress (PLS). In the stress-insensitive zone, the fracture depends on high-temperature and oxidation effects. The failure in the stress-sensitive zone is dominated by the fiber strength. The interface behaviors greatly affect the fatigue life above the PLS.     

Effect of phosphorus–nitrogen compound on flame retardancy and mechanical properties of polylactic acid

A phosphorus-nitrogen flame retardant (PN) was synthesized by using cytosine and diphenylphosphinic chloride. The flame retardancy and thermal stability of polylactic acid (PLA)/PN composites were investigated by the UL-94 vertical burning test, limited oxygen index (LOI), cone calorimeter test, and thermogravimetric analysis. The PN performs efficiently on improving the flame retardancy of PLA. The PLA composite achieves the UL-94 V-0 rating and its LOI increases to 30.4 vol% by adding 0.5 wt% PN. The flame retardant mechanism analysis showed that PN catalyzes the degradation of PLA to improve the flame retardancy by melting-away mode. Meanwhile PN reduces the release of flammable gasses during thermal degradation of PLA by promoting the transesterification of PLA, which is helpful for extinguishing flame. Moreover, triglycidyl isocyanurate (TGIC) was used as a micro-crosslinking agent to reduce the loss of mechanical properties of PLA/PN composites caused by degradation. Adding 0.1 wt% TGIC and 1.0 wt% PN into PLA, the tensile strength and elongation at break of PLA/PN are increased to the same level as that of PLA. Therefore, PLA with excellent comprehensive performance can be obtained.