Dielectric and piezoelectric properties of (1−x)(Bi,Na)TiO3–x(Bi,K)TiO3 lead-free ceramics for piezoelectric energy harvesters

The piezoelectric and dielectric properties of the (1−x)(Bi,Na)TiO₃–x(Bi,K)TiO₃ (x=0.12, 0.14, 0.18, 0.20 and 0.30) lead-free ceramics were investigated. Specimens were prepared by the conventional mixed oxide method and sintered at 1170 °C in air. Scanning electron microscopy indicated that increasing x from 0.12 to 0.30 causes a decrease in the grain size. The (1−x)(Bi,Na)TiO₃–x(Bi,K)TiO₃ ceramics shows a homogeneous microstructure and excellent dielectric and piezoelectric properties. Specimens with optimum composition showed a piezoelectric charge constant d₃₃ of 166 pC/N, an electromechanical coupling factor k_p of 0.5, a dielectric constant ε_r of 1591.32 at 1 kHz and generated power output of 37.49 nW/cm².     

Structural properties of (Bi0.5Na0.5)1−xBaxTiO3 lead-free piezoelectric ceramics

A systematic XRD investigation of poled and unpoled ceramics of the system (1 ? x) Bi_0.5Na_0.5TiO₃–x BaTiO₃ (0 ≤ x ≤ 0.2) (BNBT) was performed. The variation of the lattice parameters confirms the existence of a morphotropic phase boundary at 0.06 ≤ x ≤ 0.08; however, significant differences in unit cell parameters between poled and unpoled states appear. Lattice distortions of the rhombohedral and tetragonal phases are significantly increased in poled samples. Dramatic changes in peak intensities of the pseudo-cubic (2 0 0) reflections between poled and unpoled samples reveal a strong enhancement of the tetragonal volume fraction in the poled state. Temperature-dependent XRD studies confirm a transition into a cubic high-temperature phase. This transition is rather smooth in the unpoled state. In poled samples, the tetragonal distortion and the tetragonal volume fraction display a different temperature variation and tetragonal regions seem to persist into the cubic phase field.     

Phase structure,ferroelectric properties,and electric field-induced large strain in lead-free 0.99[(1−x)(Bi0.5Na0.5)TiO3-x(Bi0.5K0.5)TiO3]–0.01Ta piezoelectric ceramics

Lead-free 0.99[(1−x)(Bi_0.5Na_0.5)TiO₃-x(Bi_0.5K_0.5)TiO₃]–0.01Ta piezoelectric ceramics were prepared by a conventional solid-state reaction process. The ferroelectric properties, and strain behaviors were characterized. Increase of the (Bi_0.5K_0.5)TiO₃ content induces a phase transition from coexistence of ferroelectric tetragonal and rhombohedral to a relaxor pseudocubic phase. Accordingly, the ferroelectric order is disrupted significantly with the increase of (Bi_0.5K_0.5)TiO₃ content and the destabilization of the ferroelectric order is accompanied by an enhancement of the unipolar strain, which peaks at a value of 0.35% (corresponding to a large signal d₃₃ of 438 pm/V) in samples with 20 mol% (Bi_0.5K_0.5)TiO₃ content. Temperature dependent measurements of both polarization and strain from room temperature to 120 °C suggested that the origin of the large strain is due to a reversible field-induced nonpolar pseudocubic-to-polar ferroelectric phase transformation.     

Enhanced energy storage properties of BiAlO3 modified Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3 lead-free antiferroelectric ceramics

Lead-free (1−x)(0.75Bi_0.5Na_0.5TiO₃–0.25Bi_0.5K_0.5TiO₃)–xBiAlO₃ (BNT–BKT–100xBA, x=0–0.10) ceramics were prepared by two-step sintering method and their phase structure, micro morphology and electrical properties were systematically investigated. X-ray diffraction analysis indicates a pure perovskite phase for x≤0.06 as well as a structural evolution from a tetragonal toward a pseudocubic phase. Transmission electron microscopy study of the x=0.04 composition reveals the existence of antiferroelectric phase with a⁰a⁰c⁺ oxygen octahedron tilting which is in the form of nano-domains. Polarization-electric field and current-electric field hysteresis loops demonstrate that the increase of BA concentration destroys the ferroelectric order and strengthens antiferroelectric order. A much enhanced energy storage density of 1.15 J/cm³ and efficiency of 73.2% is achieved under 105 kV/cm at x=0.06. In addition, its energy storage property is found to depend weakly on temperature within the measurement range of 25–150 °C.     

Field-induced large strain in lead-free 0.99[(1−x) Bi0.5(Na0.80K0.20)0.5TiO3–xBiFeO3]–0.01(K0.5Na0.5)NbO3 piezoelectric ceramics

Lead-free 0.99[(1−x) Bi_0.5(Na_0.80K_0.20)_0.5TiO₃–xBiFeO₃]–0.01(K_0.5Na_0.5)NbO₃ (BNKT20–100xBF–1KNN) piezoelectric ceramics were fabricated through conventional techniques. Results showed that changes in BF content of BNKT20–100xBF–1KNN induced transition from the ferroelectric phase to the ergodic relaxor phase. These changes also significantly disrupted long-range ferroelectric order, thereby correspondingly adjusting the ferroelectric-relaxor transition point T_F-R to room temperature. A large strain of 0.39% at the electric-field of 80 kV/cm (corresponding to a large signal d₃₃^* of 488 pm/V) was obtained at x=0.06, which originated from the composition proximity to the ferroelectric-relaxor phase boundary. Moreover, the high-strain material exhibited exceptional fatigue resistance (up to 10⁶ cycles) as a result of the reversible field-induced phase transition. The proposed material exhibits potential for novel ultra-large stroke and nonlinear actuators that require enhanced cycling reliability.     

Phase transition behavior and electrical properties of lead-free (Bi0.5K0.5)TiO3–LiNbO3 relaxor ferroelectric ceramics

(1?x)(Bi_0.5K_0.5)TiO₃–xLiNbO₃ ((1?x)BKT–xLN) lead-free relaxor ferroelectric ceramics were prepared by a conventional solid-state route and their phase transition behavior and the corresponding electrical properties were investigated. A morphotropic phase boundary separating rhombohedral and tetragonal phases was identified in the composition range of 0.015<x<0.03, where the improved electrical properties of piezoelectric constant d₃₃=75 pC/N and electromechanical coupling factor k_p=0.18 were obtained. Moreover, all samples show typical relaxor behavior characterized by the presence of diffuse phase transition and frequency dispersion. It was found that the dielectric relaxation behavior of BKT ceramics can be obviously enhanced with the addition of LN. In addition, the effect of the LN addition on the ferroelectric properties was also investigated by measuring polarization versus electric field hysteresis loops.     

Growth and electrical properties of Na0.5Bi0.5TiO3–K0.5Bi0.5TiO3 lead-free single crystals by the TSSG method

A series of NBT-KBT lead-free crystals with dimensions of Φ 35×10 mm were successfully grown by the TSSG method. The as-grown crystals possess rhombohedral perovskite structure at room temperature. The curves ε(T) for all crystals show two abnormal dielectric peaks. The depolarization temperatures T_d derived from the first peak of curves tan δ(T) vary with the KBT content, which are 130, 150, 140, and 115 °C respectively, for (100−x)NBT−xKBT (x=5, 8, 12, 15) crystals, being well consistent with the T_d obtained from the temperature dependence of k_t. A notable thermal hysteresis, ΔT≈35 °C, for ferroelectric-antiferroelectric phase transition was also disclosed for 92NBT-8KBT crystal. The investigation of orientation dependence for electrical properties disclosed the dielectric parameters show weak anisotropy. The piezoelectric constants (d₃₃) are 147, 175, 205, 238 pC/N and the values of k_t are 38%, 52%, 52%, 54%, respectively for (100−x)NBT−xKBT (x=5, 8, 12, 15) crystals.     

Enhancing the dielectric and energy storage properties of lead-free Na0.5Bi0.5TiO3–BaTiO3 ceramics by adding K0.5Na0.5NbO3 ferroelectric

A novel strategy of enhancing the dielectric and energy storage properties of Na_0.5Bi_0.5TiO₃–BaTiO₃ (NBT–BT) ceramics by introducing a K_0.5Na_0.5NbO₃ (KNN) ferroelectric phase is proposed herein, and its underlying mechanism is elucidated. The lead-free KNN ceramic decreases the residual polarisation and increases the electric breakdown strength of the NBT–BT matrix through the simultaneous modification of its A-sites and B-sites. The obtained NBT?BT?x?KNN ceramics have a perovskite structure with unifying grains. A bulk 0.9NBT–BT–0.1KNN ceramic sample with a thickness of 0.2 mm possesses a high energy storage density of 2.81 J/cm³ at an applied electric field of 180 kV/cm. Moreover, it exhibits good insulation properties and undergoes rapid charge and discharge processes. Therefore, the obtained 0.9NBT–BT–0.1KNN ceramic can be potentially used in high-power applications because of its high energy density, good insulation properties, and large discharge rate.     

Microstructure,ferroelectric and piezoelectric properties of Bi0.5K0.5TiO3-modified BiFeO3–BaTiO3 lead-free ceramics with high Curie temperature

The effects of composition, sintering temperature and dwell time on the microstructure and electrical properties of (0.75 ? x)BiFeO₃–0.25BaTiO₃–xBi_0.5K_0.5TiO₃ + 1 mol% MnO₂ ceramics were studied. The ceramics sintered at 1000 °C for 2 h possess a pure perovskite structure and a morphotropic phase boundary of rhombohedral and pseudocubic phases is formed at x = 0.025. The addition of Bi_0.5K_0.5TiO₃ retards the grain growth and induces two dielectric anomalies at high temperatures (T₁ ～ 450–550 °C and T₂ ～ 700 °C, respectively). After the addition of 2.5 mol% Bi_0.5K_0.5TiO₃, the ferroelectric and piezoelectric properties of the ceramics are improved and very high Curie temperature of 708 °C is obtained. Sintering temperature has an important influence on the microstructure and electrical properties of the ceramics. Critical sintering temperature is 970 °C. For the ceramic with x = 0.025 sintered at/above 970 °C, large grains, good densification, high resistivity and enhanced electrical properties are obtained. The weak dependences of microstructure and electrical properties on dwell time are observed for the ceramic with x = 0.025.     

Morphotropic phase boundary and electrical properties of lead-free (K0.5Bi0.5)TiO3–Bi(Ni0.5Ti0.5)O3 relaxor ferroelectric ceramics

Lead-free relaxor ferroelectric ceramics (1?x)(K_0.5Bi_0.5)TiO₃–xBi(Ni_0.5Ti_0.5)O₃ were prepared by a conventional solid-state route, the phase transition behavior and corresponding electrical properties were investigated. A typical morphotropic phase boundary (MPB) between rhombohedral and tetragonal ferroelectric phases was identified to be in the range of 0.05<x<0.07 where the optimum piezoelectric and electromechanical properties of d₃₃=126 pC/N and k_P=18% were achieved. Most importantly, a high Curie temperature ~320 °C, around which the material shows a typical relaxor ferroelectric behavior characterized by the presence of diffuse phase transition and frequency dispersion, was obtained in MPB compositions, significantly higher than those of some existing MPB lead-free titanate systems. These results demonstrate a tremendous potential of the studied system for device applications.     

Morphotropic phase boundary and electrical properties of 1−x[Bi0.5Na0.5]TiO3 –xBa[Zr0.25Ti0.75]O3 lead-free piezoelectric ceramics

Lead-free solid solutions (1?x)Bi_0.5Na_0.5TiO₃ (BNT)–xBaZr_0.25Ti_0.75O₃ (BZT) (x=0, 0.01, 0.03, 0.05, and 0.07) were prepared by the solid state reaction method. X-ray diffraction (XRD) and Rietveld refinement analyses of 1?x(BNT)–x(BZT) solid solution ceramic were employed to study the structure of these systems. A morphotropic phase boundary (MPB) between rhombohedral and cubic structures occured at the composition x=0.05. Raman spectroscopy exhibited a splitting of the (TO₃) mode at x=0.05 and confirmed the presence of MPB region. Scanning electron microcopy (SEM) images showed a change in the grain shape with the increase of BZT into the BNT matrix lattice. The temperature dependent dielectric study showed a gradual increase in dielectric constant up to x=0.05 and then decrease with further increase in BZT content. Maximum coercive field, remanent polarization and high piezoelectric constant were observed at x=0.05. Both the structural and electrical properties show that the solid solution has an MPB around x=0.05.     

Crystal structure,microstructure and electrical properties of (1−x−y)Bi0.5Na0.5TiO3–xBi0.5K0.5TiO3–yBiFeO3 ceramics near MPB prepared via the combustion technique

(1?x?y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃–yBiFeO₃ (BNKFT-x/y with 0.12≤x≤0.24, 0≤y≤0.07) lead-free piezoelectric ceramics have been prepared by the combustion technique. The effects of amounts of x and y on structures and electrical properties were examined. Powders and ceramics can be well calcined and sintered at 750 °C for 2 h and 1025–1050 °C, respectively. The results indicated that the crystalline structure and microstructure changed with the increase of x and y concentrations. XRD results of BNKFT-x/0.03 and BNKFT-0.18/y ceramics with 0.12≤x≤0.24 and 0≤y≤0.07 showed the rhombohedral–tetragonal morphotropic phase boundary (MPB). The addition of y caused a promoted grain growth while the addition of x suppressed the grain growth. The highest density (ρ=5.85 g/cm³), superior dielectric properties at T_c (ε_r=7846 and tan δ=0.02), remnant polarization measured at 40 kV/cm (P_r = 20.1 μC/cm²) and piezoelectric coefficient (d₃₃=213 pC/N) were obtained for x=0.18 and y=0.03.     

Temperature dependent phase transition of (Bi0.5Na0.5)1−xBaxTiO3 lead-free piezoelectric

Phase transformation and electric properties of lead-free piezoceramics (Bi_0.5Na_0.5)_1?xBa_xTiO₃ with x=0.05, 0.06, and 0.07(BNB5T, BNB6T and BNB7T) were investigated using dielectric, piezoelectric and ferroelectric measurements. Electric field induced strain measurement shows “W” shape bipolar strain characteristics for BNB5T with typical ferroelectric P–E curve, while BNB6T and BNB7T, possessing pinch-off P–E, exhibit “V” shape field-induced strain. All the BNBxT specimens exhibit relaxor characteristic, identified by the Debye Law. Dielectric properties measured at elevated temperatures with the frequency variation (10–500 kHz) reveal frequency dispersion below the T_d point, but no dispersion between T_d and T_m, which may be ascribed to an intermediate phase transition. By adding more Ba²⁺ ions, the region of intermediate phase, distinguished by frequency dependence dielectric constant, expands to lower temperature. Moreover, the ferroelectric properties measured at elevated temperature were carried out below and at the depolarization temperature to well investigate the existence of this phase. Much less ε–T profile dispersion were observed during the investigation of BNB6T and BNB7T, leading to possible existence of an intermediate phase in the investigated compositions. The results suggest that the linear field-induced-strain of (Bi_0.5Na_0.5)_1?xBa_xTiO₃ are expected to be attributed to the intermediate phase.     

Structural evolution and ferroelectric properties in lead-free (1−x)(Bi0.5Na0.4K0.1)TiO3-xSrTiO3 solid solutions

Bi_0.5Na_0.5TiO₃ (BNT)-based dielectric ceramics have received a lot of attention due to the increased demand for pulse ceramic capacitors. However, comprehensive study on the relationship between their internal phase structure, dielectric characteristics, and ferroelectric properties is still lacking. The phase evolution and its impact on dielectric and ferroelectric properties of an important BNT-based solid solution, Bi_0.5Na_0.4K_0.1TiO₃-xSrTiO₃ (x = 0, 0.1, 0.2, 0.3 and 0.4), were investigated systematically in this work using structural, dielectric, and ferroelectric characterization techniques. X-ray diffraction indicated the coexistence of rhombohedral and tetragonal phases. The frequency- and temperature-dielectric characterization was then used to derive the characteristic temperatures T_B, T_m, T_s, and T_d, and a phase diagram was developed. Furthermore, the temperature-dependent current against electric field curves and polarization versus electric field loops were used to derive the characteristic temperatures connected to high electric field features. This study not only explains the phase evolution of the Bi_0.5Na_0.4K_0.1TiO₃-xSrTiO₃ solid solution, but it also correlates microscopic domains and polar nanoregions to macroscopic dielectric and ferroelectric properties.     

Ferroelectric properties and large electric field-induced strain of Eu3+-doped Na0.5Bi0.5TiO3–BaTiO3 lead-free ceramics

Eu³⁺-doped lead-free piezoelectric ceramics, 0.937Na_0.5Bi_0.5?xEu_xTiO₃-0.063BaTiO₃ (abbreviated as NBE_xT-BT, where x = 0, 0.003, 0.005, 0.01, 0.013, 0.015, 0.017, and 0.02), were synthesized using a conventional solid-state synthesis method. All the component samples were crystallized in a pure perovskite structure without a secondary phase. The introduction of Eu³⁺ caused the evident variation of the dielectric, ferroelectric and luminescence properties. The remanent polarization and coercive field of the pure NBT-BT are P_r ～29.24 μC/cm², E_c～39.33 kV/cm, respectively. The maximum of the remanent polarization P_r of ～38.02 μC/cm² at room temperature and the highest dielectric constant of 6899 with a frequency of 1 kHz were obtained for NBE_0.003T-BT. The maximum bipolar strain S_max of ～0.91% and the minimum of coercive field E_c ～18.45 kV/cm were achieved by the NBE_0.015T-BT, resulting from the formation of a double hysteresis loop. For all the components, Eu³⁺ doping stabilized the antiferroelectric phenomenon at high temperature. Furthermore, the polarized NBE_0.015T-BT had the strongest fluorescence luminescence intensity as well as a fluorescence lifetime reaching 785.98 μs.     

Phase transition behavior and electrical properties of (1 − x)Bi0.5Na0.5TiO3–x(Na0.53K0.44Li0.04)(Nb0.88Sb0.08Ta0.04)O3 lead-free ceramics

(1 ? x)Bi_0.5Na_0.5TiO₃–x(Na_0.53K_0.44Li_0.04)(Nb_0.88Sb_0.08Ta_0.04)O₃ (BNT–xNKLNST) with x = 0–0.10 lead-free piezoelectric ceramics were prepared by a solid state method, and the structure and electrical properties were investigated in this study. It is found that a morphotropic phase boundary (MPB) of rhombohedral (R) and tetragonal (T) phase exists in the range of 0.03 ≤ x ≤ 0.05 and the structure changes to paraelectric phase when x > 0.07. The samples with x = 0.05 exhibit improved electrical properties owing to the formation of MPB, which are as follows: piezoelectric constant d₃₃ = 120 pC/N, remnant polarization P_r = 39.4 μC/cm² and coercive field E_c = 3.6 kV/mm. These results indicate that the enhanced piezoelectric properties for BNT can be achieved by forming the coexistence of R and T phase.     

Fabrication of transparent electro-optic (K0.5Na0.5)1−xLixNb1−xBixO3 lead-free ceramics

Lead-free transparent electro-optic ceramics (K_0.5Na_0.5)_1?xLi_xNb_1?xBi_xO₃ have been fabricated by hot-press sintering. Owing to the effective suppression of grain growth, the Li and Bi co-modified ceramics generally possess a dense and fine-grained structure. The co-modification also causes the ceramics to transform into a nearly cubic structure with minimal optical anisotropy. A diffuse phase transformation is also induced, causing the ceramics to become more relaxor-like and contain more polar nano-regions. These would reduce the light scattering by the grains, at the grain boundaries and at the domain walls, respectively, and thus making the ceramics become optically transparent. For the ceramic modified with 5 mol% Li⁺ and Bi⁵⁺, the optical transmittance reaches a high value of 60% in the near-IR region. The ceramics also exhibit a strong linear EO response, giving a large effective linear EO coefficient in the range of 120–200 pm/V.     

Quantification of relaxor behavior in (1 − x)Na0.5Bi0.5TiO3 – xCaTiO3 lead-free ceramics system

This work examines the relaxor behavior of lead-free ceramic (1 − x)Na_0.5Bi_0.5TiO₃–xCaTiO₃ systems. A stable rhombohedral (R3c) phase is detected at room temperature for all compositions by XRD and Raman spectroscopy. Relaxor behavior was observed in the temperature range 300 K - 400 K for all materials. Ceramics exhibit normal ferroelectric properties at room temperature, and then they develop relaxor characteristics with increasing temperature showing the same dispersive properties. This work quantifies the relaxor phenomenon at low temperature. For instance, the maximum temperature of relaxor and the order of dispersion were determined at the strongest dispersion. Finally, the substitution by low CT concentration unaltered the relaxor behavior at low temperature.